Search NASA⌕ Search

SEARCH · Search NASA

Results for “ROLLING ELEMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Microstructure development of novel composite heating elements for steel decarbonization

The iron and steel industry is critical for the modern world but is also responsible for 7% of the total energy sector CO2 emissions. It is a difficult industry to decarbonize due to the high temperature heat required for the production of steel, such as reheating steel slabs to ~1250 °C for hot rolling. Electrification of this process using resistive heating is currently not possible due to the poor creep resistance of MoSi2 heating elements, which need to be operated well below their maximum temperatures when mounted horizontally. To solve this problem, novel MoSi2 composite heating elements with SiBCN ceramic reinforcements are being developed using high energy ball milling and electric field assisted sintering (EFAS). The microstructure and density of the composites after sintering depends on the sintering parameters chosen. Herein we present the effects of EFAS sintering parameters on the microstructure and density of the MoSi2-SiBCN composites.

36 - MATERIALS SCIENCE↗

Aeroacoustic Simulations of the High-Lift Common Research Model and Validation with Experiment

Aerodynamic and acoustic data from unsteady numerical simulations of the High-Lift Common Research Model are compared with experimental measurements from an open-jet wind tunnel test of a 10\-scale model. Time-averaged surface pressure data is in good agreement for all of the configurations evaluated during the test. Unsteady surface pressure spectra from the leading-edge slat and the nose of the main element are presented, demonstrating that the highest levels are associated with the wakes of slat brackets. At these locations the simulations and experiment match reasonably well at low enough frequencies (f < 10 kHz based on the model scale) before excessive numerical dissipation leads to a rapid roll off in the predicted frequency spectra. The agreement is inconsistent at other locations on the slat and main-element surfaces, where the pressure fluctuation levels are lower. Noise predictions using a synthetic microphone array are compared with equivalent experimental results, and the changes in levels predicted between three configurations are similar to those measured. However, some details of the noise predictions are inconsistent with the experiment, and the use of solid- instead of porous-surface data for the acoustic processing of the simulations likely contributes to the discrepancies. All of the simulations were completed before the test, and, despite some shortcomings, they provided valuable insight into the aeroacoustic performance of the model that greatly aided test planning and execution. Hence, the post-test comparisons presented here allow an assessment of the predictive methodology in the context of a realistic high-lift configuration.

High-lift↗

Tailoring ductile-phase toughened tungsten hierarchical microstructures for plasma-facing materials

Biological materials, such as bones, nacre, etc., have been found to show attractive and unique combinations of stiffness, strength and fracture toughness. Research has been conducted in various engineering areas to mimic the naturally hierarchical microstructures or nanostructures of these materials to produce materials with optimum stiffness, high strength and fracture toughness for their intended structural applications. In the same objective, this work applies a multiscale microstructural approach recently developed to investigate the deformation and fracture behavior of ductile phase toughened tungsten (W) materials such as tungsten-nickel/iron (W-Ni/Fe) composites that possess lamellar-like and hierarchical “brick-and-mortar” (BAM) microstructures. First, the approach is used to simulate tensile loading of W-Ni/Fe specimens cut out from hot-rolled W-Ni/Fe plates which possess lamellar-like microstructures. The finite element model of the gage section of the specimen consists of a W-Ni/Fe dual-phase microstructural domain in which the constitutive behaviors of W and Ni/Fe phases are described by an elastic-plastic damage model. The predicted material stress-strain response and crack pattern development as a function of loading are then compared to the corresponding experimental results to determine the constitutive model parameters for W and Ni/Fe. Subsequently, the model parameters are used to analyze W-Ni/Fe BAM microstructures that are artificially created to investigate the effects of microstructural features and morphologies on the composite stress-strain response, damage, and fracture patterns. The modeling shows that regular BAM microstructures that experience bridging mechanism combined with crack penetration across W-phase regions exhibit significantly higher strengths than the rather random lamellar-like microstructures. More significantly, however adjusting the brick’s length-to-height ratio, the BAM microstructure can be designed to allow a more distributed damage zone which leads to increased strength, ductility and fracture energy.

36 MATERIALS SCIENCE↗

Applicability of discrete element method with spherical and clumped particles for constitutive study of granular materials

Discrete element method (DEM) has been intensively used to study the constitutive behaviour of granular materials. However, to what extent a real granular material can be reproduced by virtual DEM simulations remains unclear. This study attempts to answer this question by comparing DEM simulations with typical features of experimental granular materials. Three groups of models with spherical and clumped particles are investigated from four perspectives: (i) deviatoric stress and volumetric behaviour; (ii) critical state behaviour; (iii) stress-dilatancy relationship; and (iv) the evolution of principal stress ratio against axial strain. The results demonstrate that DEM with spherical or clumped particles is capable of qualitatively describing macroscopic deviatoric stress responses, volumetric behaviour, and critical state behaviour observed in experiments for granular materials. On the other hand, some qualitative deviations between experiments and the investigated DEM simulations are also observed, in terms of the stress-dilatancy behaviour and principal stress ratio against axial strain, which are proven to be critical for constitutive modelling. The results demonstrate that DEM with spherical or clumped particles may not necessarily fully capture experimental features of granular materials even from a qualitative perspective. It is thus encouraged to thoroughly validate DEM with experiments when developing constitutive models based on DEM observations.

58 GEOSCIENCES↗

High Strength and Compatible Aluminum Alloy for Hydrogen-Peroxide Fuel Tanks

This paper describes the development of a new high strength and Hydrogen Peroxide (HP) propellant compatible aluminum alloy for NASA Hyper-X vehicle's fuel tanks and structures. The tensile strength of the new alloy is more than 3 times stronger than the conventional 5254 alloy while it still maintains HP compatibility similar to 5254 (Class 1 category). The alloy development strategy consists of selecting certain rare earth and transition metals, with unique electrochemical properties, that will not act as catalysts to decompose liquid HP at the atomic level. Such elements will added to the aluminum alloy and the mixture will be cast and rolled into thin sheet metals. Test coupons are machined from sheet metals for HP long-term exposure testing and mechanical properties testing. In addition, the ability to weld the new alloy using Friction Stir Welding has also been explored. Currently, aluminum alloy 5254 is the state-of-the-art material for HP storage, but its yield strength is very low (420 ksi) and may not be suitable for the development of light-weight fuel tanks for Hyper-X vehicles. The new high strength and HP compatible alloy could represent an enabling material technology for NASA's Hyper-X vehicles, where flight weight reduction is a critical requirement. These X-planes are currently under studied as air-breathing hypersonic research vehicles featuring a lifting body configuration with a Rocket Based Combined Cycle (RBCC) engine system.

Lee, Jonathan A.↗

Discrete Element Modeling (DEM) of Triboelectrically Charged Particles: Revised Experiments

In a previous work, the addition of basic screened Coulombic electrostatic forces to an existing commercial discrete element modeling (DEM) software was reported. Triboelectric experiments were performed to charge glass spheres rolling on inclined planes of various materials. Charge generation constants and the Q/m ratios for the test materials were calculated from the experimental data and compared to the simulation output of the DEM software. In this paper, we will discuss new values of the charge generation constants calculated from improved experimental procedures and data. Also, planned work to include dielectrophoretic, Van der Waals forces, and advanced mechanical forces into the software will be discussed.

Hogue, Michael D.↗

Solution-Processed Composite Transparent Metal Network Conductors for Next Generation Scalable PV

Transparent conductors (TCs) are essential components of thin film PV cells. Inherently, ITO and other related TC oxides, have fundamental trade-offs that balance conductivity versus optical transmission losses from metallic absorption and reflectivity. Furthermore, the ITO sputtering, materials and patterning costs represent one of the highest cost elements in the thin film cell process. As we consider emerging technologies such as roll to roll processing on lower temperature substrates, the problem is compounded by high ITO processing temperatures. Low temperature alternatives do exist, however, they cannot reach the metrics for high efficiency PV on their own. Numerical modeling has shown that combining high transparency, modestly conducting films with printed conductive grids can provide a TC with a 30% reduction in power loss relative to ITO. During this talk, current work on nanowire and printed TC films will be presented and the scale-up pathways for these technologies will be discussed.

14 SOLAR ENERGY↗

Accuracy Analysis of Anisotropic Yield Functions based on the Root-Mean Square Error

This paper evaluates the accuracy of popular anisotropic yield functions based on the root-mean square error (RMSE) of the yield stresses and the R-values. The yield functions include Hill48, Yld89, Yld91, Yld96, Yld2000-2d, BBC2000 and Yld2000-18p yield criteria. Two kind steels and five kind aluminum alloys are selected for the accuracy evaluation. The anisotropic coefficients in yield functions are computed from the experimental data. The downhill simplex method is utilized for the parameter evaluation for the yield function except Hill48 and Yld89 yield functions after the error functions are constructed. The yield stresses and the R-values at every 15 deg. from the rolling direction (RD) and the yield stress and R-value at equibiaxial tension conditions are predicted from each yield function. The predicted yield stresses and R-values are then compared with the experimental data. The root-mean square errors (RMSE) are computed to quantitatively evaluate the yield function. The RMSEs are calculated for the yield stresses and the R-values separately because the yield stress difference is much smaller that the difference in the R-values. The RMSEs of different yield functions are compared for each material. The Hill48 and Yld89 yield functions are the worst choices for the anisotropic description of the yield stress anisotropy while Yld91 yield function is the last choice for the modeling of the R-value directionality. Yld2000-2d and BBC2000 yield function have the same accuracy on the modeling of both the yield stress anisotropy and the R-value anisotropy. The best choice is Yld2000-18 yield function to accurately describe the yield tress and R-value directionalities of sheet metals.

36 MATERIALS SCIENCE↗

Processing and mechanical properties - 2016-0032

Hot extrusion is used within the forming route of cladding tubes to deform the billets into tube hollows, which are then cold-rolled to produce the final tubes with the suitable properties for in-reactor use. The hot extrusion goals are to give the appropriate geometry for cold pilgering (diameter and wall thickness suitable for cold-rolling mills, good concentricity) without surface defects and microstructural heterogeneities, which are detrimental for subsequent rolling. To ensure a good quality of the tube hollows, extrusion parameters (e.g., temperature of the billet, ram speed, extrusion ratio, lubrication) and extrusion tools have to be chosen as a function of the press capacity and mechanical and microstructural properties of the extruded alloy. For this purpose, finite-element and analytical models are used in addition to experimental tests. These models, particularly the former, can take into account the thermomechanical coupling that occurs in the tube and the tools during extrusion and provides a good prediction of the extrusion pressure and thermomechanical history of the extruded product. Together with a microstructural evolution model identified with small-scale extrusion tests, torsion tests, and heat treatments, this last result can also be used to calculate the fragmentation of the microstructure in the die and the meta-dynamic recrystallization after extrusion. Once validated against experimental data, numerical models were used to better understand and master the extrusion loads, the microstructure evolutions at the front end of the extruded tubes, and the temperature and stresses applied to the tools. (authors)

36 MATERIALS SCIENCE↗

Experimental investigation on the electrical contact behavior of rolling contact connector

Rolling contact connector (RCC) is a new technology utilized in high performance electric power transfer systems with one or more rotating interfaces, such as radars, satellites, wind generators, and medical computed tomography machines. Rolling contact components are used in the RCC instead of traditional sliding contacts to transfer electrical power and/or signal. Since the requirement of the power transmission is increasing in these years, the rolling electrical contact characteristics become more and more important for the long-life design of RCC. In this paper, a typical form of RCC is presented. A series of experimental work are carried out to investigate the rolling electrical contact characteristics during its lifetime. The influence of a variety of factors on the electrical contact degradation behavior of RCC is analyzed under both vacuum and air environment. Based on the surface morphology and elemental composition changes in the contact zone, which are assessed by field emission scanning electron microscope and confocal laser scanning microscope, the mechanism of rolling electrical contact degradation is discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Constitutive modelling of lubricants in concentrated contacts at high slide to roll ratios

A constitutive lubricant friction model for rolling/sliding concentrated contacts such as gears and cams was developed, based upon the Johnson and Tevaarwerk fluid rheology model developed earlier. The friction model reported herein differs from the earlier rheological models in that very large slide to roll ratios can now be accommodated by modifying the thermal response of the model. Also the elastic response of the fluid has been omitted from the model, thereby making it much simpler for use in the high slide to roll contacts. The effects of this simplification are very minimal on the outcome of the predicted friction losses (less than 1%). In essence then the lubricant friction model developed for the high slide to roll ratios treats the fluid in the concentrated contact as consisting of a nonlinear viscous element that is pressure, temperature, and strain rate dependent in its shear response. The fluid rheological constants required for the prediction of the friction losses at different contact conditions are obtained by traction measurements on several of the currently used gear lubricants. An example calculation, using this model and the fluid parameters obtained from the experiments, shows that it correctly predicts trends and magnitude of gear mesh losses measured elsewhere for the same fluids tested here.

Tevaarwerk, J. L.↗

Contact solution algorithms

Two algorithms for obtaining static contact solutions are described in this presentation. Although they were derived for contact problems involving specific structures (a tire and a solid rubber cylinder), they are sufficiently general to be applied to other shell-of-revolution and solid-body contact problems. The shell-of-revolution contact algorithm is a method of obtaining a point load influence coefficient matrix for the portion of shell surface that is expected to carry a contact load. If the shell is sufficiently linear with respect to contact loading, a single influence coefficient matrix can be used to obtain a good approximation of the contact pressure distribution. Otherwise, the matrix will be updated to reflect nonlinear load-deflection behavior. The solid-body contact algorithm utilizes a Lagrange multiplier to include the contact constraint in a potential energy functional. The solution is found by applying the principle of minimum potential energy. The Lagrange multiplier is identified as the contact load resultant for a specific deflection. At present, only frictionless contact solutions have been obtained with these algorithms. A sliding tread element has been developed to calculate friction shear force in the contact region of the rolling shell-of-revolution tire model.

Tielking, John T.↗

Prediction of contact path and load sharing in spiral bevel gears

A procedure is presented to perform a contact analysis of spiral bevel gears in order to predict the contact path and the load sharing as the gears roll through mesh. The approach utilizes recent advances in automated contact methods for nonlinear finite element analysis. A sector of the pinion and gear is modeled consisting of three pinion teeth and four gear teeth in mesh. Calculation of the contact force and stresses through the gear meshing cycle are demonstrated. Summary of the results are presented using three dimensional plots and tables. Issues relating to solution convergence and requirements for running large finite element analysis on a supercomputer are discussed.

Bibel, George D.↗

Concept Feasibility Report for Electroplating Zirconium onto Uranium Foil - Year 2

The Fuel Fabrication Capability within the U.S. High Performance Research Reactor Conversion Program is funded through the National Nuclear Security Administration (NNSA) NA-26 (Office of Material Management and Minimization). An investigation was commissioned to determine the feasibility of using electroplating techniques to apply a coating of zirconium onto depleted uranium/molybdenum alloy (U-10Mo). Electroplating would provide an alternative method to the existing process of hot roll-bonding zirconium foil onto the U-10Mo fuel foil during the fabrication of fuel elements for high-performance research reactors. The objective of this research was to develop a reproducible and scalable plating process that will produce a uniform, 25 μm thick zirconium metal coating on U-10Mo foil. In previous work, Pacific Northwest National Laboratory (PNNL) established a molten salt electroplating apparatus and protocol to plate zirconium metal onto molybdenum foil (Coffey 2015). During this second year of the research, PNNL furthered this work by moving to the U-10Mo alloy system (90 percent uranium:10 percent molybdenum). The original plating apparatus was disassembled and re-assembled in a laboratory capable of handling low-level radioactive materials. Initially, the work followed the previous year’s approach, and the salt bath composition was targeted at the eutectic composition (LiF:NaF:ZrF4 = 26:37:37 mol%). Early results indicated that the formation of uranium fluoride compounds would be problematic. Other salt bath compositions were investigated in order to eliminate the uranium fluoride production (LiF:NaF = 61:39 mol% and LiF:NaF:KF = 46.5:11.5:42 mol% ). Zirconium metal was used as the crucible for the molten salt. Three plating methods were used—isopotential, galvano static, and pulsed plating. The molten salt method for zirconium metal application provided high-quality plating on molybdenum in PNNL’s previous work. A key advantage of this approach is that plating can be performed under conditions that would greatly reduce the quantity of intermetallics that form at the interface between the zirconium and U-10Mo; unlike roll bonding, the molten salt plating approach would allow for complete coverage of the U-10Mo foil with zirconium. When utilizing the experimental parameters developed for zirconium plating onto molybdenum, a uranium fluoride reaction product was formed at the Zr/U-10Mo interface. By controlling the initial plating potential, the uranium fluoride could be prevented; however, the targeted zirconium thickness (25 ±12.5 μm) could not be achieved while maintaining 100% coverage.

36 MATERIALS SCIENCE↗

The NPOESS Preparatory Project (NPP) Science Data Segment (SDS) Data Depository and Distribution Element (SD3E) System Architecture

The National Polar-orbiting Operational Environmental Satellite System (NPOESS), the U.S. Government's future low-Earth orbiting satellite system, will monitor global weather and environmental conditions. Serving as a risk reduction for NPOESS, the NPOESS Preparatory Project (NPP) will provide remotely sensed atmospheric, land, ocean, ozone, and sounder data that will serve the meteorological and global climate change scientific communities. The National Aeronautics and Space Administration (NASA) NPP Science Data Segment's (SDS) primary role is to independently assess the quality of the NPP science and environmental data records for their ability to support climate research. The SDS is composed of nine elements; an input element that receives data from the operational agencies and acts as a buffer, a calibration analysis element, five elements devoted to measurement based quality assessment, an element used to test algorithmic improvements, and an element that provides overall science direction. Each element requires a set of sensor specific science data products for their evaluation. There are four NPP sensors that will be flown on the NPP observatory. They are the Visible Infrared Imagining Radiometer Suite (VIIRS), the Advanced Technology Microwave Sounder (ATMS), the Cross-Track Infrared Sounder (CrIS), and the Ozone Mapper/Profiler Suite (OMPS). It is estimated that these four sensors combined will make daily data requests for approximately six terabytes of NPP science products from the operational data providers. As a result, issues associated with duplicate data requests, data transfers of large volumes of diverse products, and data transfer failures raised concerns with respect to the network traffic and bandwidth consumption. Therefore, a central data broker system for receiving and buffering data requests and data products for the SDS was developed. The data element for this system is called the SDS Data Depository and Distribution Element (SD3E). It supports science mission data assessment by assuring the timely and validated acquisition and subsequent transfer of the NPP Science Mission data to the SDS Elements and NPP Science Team. The six science elements that interface with the SD3E span across the NASA Goddard Space Flight Center (GSFC), the NASA Jet Propulsion Laboratory (JPL), and the University of Wisconsin. As the primary communication vehicle for the science elements and science team, the SD3E has an interface to the operational data providers: National Environment Satellite, Data, and Information Service (NESDIS) Interface Data Processing System (IDPS) and the National Oceanic Atmospheric Administration's (NOAA) Comprehensive Large Array-data Stewardship system (CLASS) Archive Data System (ADS), that are responsible for product generation and archive and distribution respectively. The SD3E is designed to be a semi-customizable and semi-automated system. This system is designed to provide flexibility and ease of use for the science users in accessing the latest data products by creating a rolling data cache that temporarily stores the products locally before transferring the data to the SDS Measurement based elements for the land, ocean, atmosphere, sounder, and ozone. This paper describes the design and architecture of one of the nine SDS elements, the SD3E, and how this system has provided a mechanism for efficient data exchange, how it has helped in alleviating some of the network traffic and usage, and how it has contributed to reducing operational costs.

Ho, Evelyn L.↗

Experimental and Computational Investigation of High Entropy Alloys for Elevated-Temperature Applications

To create and design novel structural materials with enhanced creep-resistance, fundamental studies have been conducted on high-entropy alloys (HEAs), using (1) thermodynamic calculations, (2) mechanical tests, (3) neutron diffraction, (4) characterization techniques, and (5) crystal-plasticity finite-element modeling (CPFEM), to explore future candidates for next-generation power plants. All the constituent binary and ternary systems of the Al-Cr-Cu-Fe-Mn-Ni and Al-Co-Cr-Fe-Ni systems were thermodynamically modeled within the whole composition range. Comparisons between the calculated phase diagrams and literature data are in good agreement. Seven types of HEAs were fabricated from Al-Cr-Cu-Fe-Mn-Ni and Al-Co-Cr-Fe-Ni systems. The Al x CrCuFeMnNi HEAs have disordered [face-centered cubic (FCC) + body-centered cubic (BCC)] crystal structures, not FCC or BCC single structure. Excessive alloying of the Al element results in the change of both microstructural and mechanical properties in Al x CoCrFeNi HEAs. There are mainly three structural features in Al x CoCrFeNi: (1) the morphology, (2) the volume fractions of the constitute phases, and (3) existing temperatures of all six phases. After homogenization, the Al 0.3 CoCrFeNi material is a pure FCC solid solution. After aging at 700 °C for 500 hours, the optimal microstructure combinations, the FCC matrix, needle-like B2 phase within grains, and granular σ phase along grain boundary, is achieved for Al 0.3 CoCrFeNi. The cold-rolling process is utilized to reduce the grain size of Al 0.1 CoCrFeNi and Al 0.3 CoCrFeNi. The chemical elemental partitioning of FCC, BCC, B2, and σphases at different temperatures, before and after mechanical tests, in Al-Cr-Cu-Fe-Mn-Ni and Al-Co-Cr-Fe-Ni systems are quantitatively characterized by both synchrotron X-ray diffraction, neutron diffraction with levitation, scanning electron microscopy (SEM), advanced atom probe tomography (APT), and transmission electron microscopy (TEM). In-situ neutron diffraction experiments were conducted to study the strengthening effect of B2 phase on tensile properties of Al 0.3 CoCrFeNi HEAs directly. The results shows the creep behavior of Al 0.3 CoCrFeNi is superior to conventional alloys, and the heat treatment introduces secondary B2 phase into the FCC matrix, which increase the yielding strength, decrease the ductility, diminish the serrated flow during compression tests at high temperatures. In summary, the outcomes of the development of the HEAs with creep resistance include: (1) Suitable candidates, for the application to boilers and steam and gas turbines at temperatures above 760 °C and a stress of 35 MPa. (2) Fundamental understanding on the precipitate stability and deformation mechanisms of both single-phase and precipitate-strengthened alloys at room and elevated temperatures, and (3) The demonstration of an integrated approach, coupling modeling [thermodynamic calculations and crystal-plasticity finite-element modeling (CPFEM)] and focused experiments, to identify HEAs that outperform conventional alloys for high-temperature applications, which will be applicable for the discovery and development of other high-temperature materials in the power-generating industry.

36 MATERIALS SCIENCE↗

Some Experimental Results in the Rolling of Ni3Al Alloy

This study examines several issues to understand the cold rollability of Ni3Al alloy. It finds that the cold rolling response of Ni3Al alloy (IC50) is very sensitive to the starting thickness. The segregation of elements is worse for the thicker casting as opposed to the thinner section. This is exemplified by the point that cast plus annealed pieces showed cracking at much larger reduction as opposed to the as-cast piece.

Shih, Hui-Ru↗

Method of forming a hardened surface on a substrate

The invention includes a method of producing a hard metallic material by forming a mixture containing at least 55% iron and at least one of B, C, Si and P. The mixture is formed into an alloy and cooled to form a metallic material having a hardness of greater than about 9.2 GPa. The invention includes a method of forming a wire by combining a metal strip and a powder. The metal strip and the powder are rolled to form a wire containing at least 55% iron and from two to seven additional elements including at least one of C, Si and B. The invention also includes a method of forming a hardened surface on a substrate by processing a solid mass to form a powder, applying the powder to a surface to form a layer containing metallic glass, and converting the glass to a crystalline material having a nanocrystalline grain size.

Branagan, Daniel J↗