Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS INTENSITY FACTORS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Crack growth in single-crystal silicon

Crack growth in single-crystal silicon at room temperature in air was evaluated by double torsion (DT) load-relaxation method and monitored by acoustic emission (AE) technique. Both DT and AE methods indicated lack of subcritical crack growth in silicon. At the critical stress intensity factor, the crack front was found to be jumping several times in a 'mirror' region and then followed by fast crack growth in a 'hackle' region. Hackle marks were found to be associated with plastic deformation at the tip of the fast moving crack. No dislocation etch pits were found in the 'mirror' region, in which crack growth may result from interatomic bonds broken at the crack tip under stress without any plastic deformation. Acoustic emission appears to be spontaneously generated from both interatomic bonds broken and dislocation generation at the moving crack tip during the crack growth in single-crystal silicon.

Chen, C. P.↗

Deformation mechanisms of nanotwinned Al

The objective of this project is to investigate the role of different types of layer interfaces on the formation of high density stacking fault (SF) in Al in Al/fcc multilayers, and understand the corresponding deformation mechanisms of the films. Stacking faults or twins can be intentionally introduced (via growth) into certain fcc metals with low stacking fault energy (such as Cu, Ag and 330 stainless steels) to achieve high strength, high ductility, superior thermal stability and good electrical conductivity. However it is still a major challenge to synthesize these types of defects into metals with high stacking fault energy, such as Al. Although deformation twins have been observed in some nanocrystalline Al powders by low temperature, high strain rate cryomilling or in Al at the edge of crack tip or indentation (with the assistance of high stress intensity factor), these deformation techniques typically introduce twins sporadically and the control of deformation twin density in Al is still not feasible. This project is designed to test the following hypotheses: (1) Certain type of layer interfaces may assist the formation of SF in Al, (2) Al with high density SF may have deformation mechanisms drastically different from those of coarse-grained Al and nanotwinned Cu. To test these hypotheses, we have performed the following tasks: (i) Investigate the influence of layer interfaces, stresses and deposition parameters on the formation and density of SF in Al. (ii) Understand the role of SF on the deformation behavior of Al. In situ nanoindentation experiments will be performed to probe deformation mechanisms in Al. The major findings related to the formation mechanism of twins and mechanical behavior of nanotwinned metals include the followings: 1) Our studies show that nanotwins can be introduced into metals with high stacking fault energy, in drastic contrast to the general anticipation. 2) We show two strategies that can effectively introduce growth twins in high-stacking-energy metals: use Ag as a template to introduce high density growth twins in epitaxial Al; and the film thickness is important in determination of volume fraction of growth twins. 3) We prove that high density twin boundaries can lead to significant work hardening capability in nanotwinned Al. We have published 13 articles, including Nature Communications, Nano Letters, and two review articles, one in Annual Review of Materials Research; and one in MRS Bulletin. Two postdocs and three graduate students have worked on the project. Two of them have become postdoc at Sandia National Laboratory and Los Alamos National Laboratory. One of the postdoc has become a faculty at a University. One patent has been filed.

36 MATERIALS SCIENCE↗

The compelling case for indentation as a functional exploratory and characterization tool

The utility of indentation testing for characterizing a wide range of mechanical properties of brittle materials is highlighted in light of recent articles questioning its validity, specifically in relation to the measurement of toughness. Contrary to assertion by some critics, indentation fracture theory is fundamentally founded in Griffith–Irwin fracture mechanics, based on model crack systems evolving within inhomogeneous but well-documented elastic and elastic–plastic contact stress fields. Notwithstanding some numerical uncertainty in associated stress intensity factor relations, the technique remains an unrivalled quick, convenient and economical means for comparative, site-specific toughness evaluation. Most importantly, indentation patterns are unique fingerprints of mechanical behavior and thereby afford a powerful functional tool for exploring the richness of material diversity. At the same time, it is cautioned that unconditional usage without due attention to the conformation of the indentation patterns can lead to overstated toughness values. Limitations of an alternative, more engineering approach to fracture evaluation, that of propagating a precrack through a “standard” machined specimen, are also outlined. Thus misconceptions in the critical literature concerning the fundamental nature of crack equilibrium and stability within contact and other inhomogeneous stress fields are discussed.

36 MATERIALS SCIENCE↗

Measurement of Fatigue Crack Growth Relationships in Hydrogen Gas for Pressure Swing Adsorber Vessel Steels

We measured the hydrogen-assisted fatigue crack growth rates (da/dN) for SA516 Grade 70 steel as a function of stress-intensity factor range (ΔK) and load-cycle frequency to provide life-prediction data relevant to pressure swing adsorber (PSA) vessels. For ΔK values up to 18.5 MPa m 1/2 , the baseline da/dN versus ΔK relationship measured at 1Hz in 2.8 MPa hydrogen gas represents an upper bound with respect to crack growth rates measured at lower frequency. However, at higher ΔK values, we found that the baseline da/dN data had to be corrected to account for modestly higher crack growth rates at the lower frequencies relevant to PSA vessel operation.

36 MATERIALS SCIENCE↗

Probabilistic Simulation of Progressive Fracture in Bolted-Joint Composite Laminates

This report describes computational methods to probabilistically simulate fracture in bolted composite structures. An innovative approach that is independent of stress intensity factors and fracture toughness was used to simulate progressive fracture. The effect of design variable uncertainties on structural damage was also quantified. A fast probability integrator assessed the scatter in the composite structure response before and after damage. Then the sensitivity of the response to design variables was computed. General-purpose methods, which are applicable to bolted joints in all types of structures and in all fracture processes-from damage initiation to unstable propagation and global structure collapse-were used. These methods were demonstrated for a bolted joint of a polymer matrix composite panel under edge loads. The effects of the fabrication process were included in the simulation of damage in the bolted panel. Results showed that the most effective way to reduce end displacement at fracture is to control both the load and the ply thickness. The cumulative probability for longitudinal stress in all plies was most sensitive to the load; in the 0 deg. plies it was very sensitive to ply thickness. The cumulative probability for transverse stress was most sensitive to the matrix coefficient of thermal expansion. In addition, fiber volume ratio and fiber transverse modulus both contributed significantly to the cumulative probability for the transverse stresses in all the plies.

Minnetyan, L.↗

Gear Crack Propagation Investigation

Reduced weight is a major design goal in aircraft power transmissions. Some gear designs incorporate thin rims to help meet this goal. Thin rims, however, may lead to bending fatigue cracks. These cracks may propagate through a gear tooth or into the gear rim. A crack that propagates through a tooth would probably not be catastrophic, and ample warning of a failure could be possible. On the other hand, a crack that propagates through the rim would be catastrophic. Such cracks could lead to disengagement of a rotor or propeller from an engine, loss of an aircraft, and fatalities. To help create and validate tools for the gear designer, the NASA Lewis Research Center performed in-house analytical and experimental studies to investigate the effect of rim thickness on gear-tooth crack propagation. Our goal was to determine whether cracks grew through gear teeth (benign failure mode) or through gear rims (catastrophic failure mode) for various rim thicknesses. In addition, we investigated the effect of rim thickness on crack propagation life. A finite-element-based computer program simulated gear-tooth crack propagation. The analysis used principles of linear elastic fracture mechanics, and quarter-point, triangular elements were used at the crack tip to represent the stress singularity. The program had an automated crack propagation option in which cracks were grown numerically via an automated remeshing scheme. Crack-tip stress-intensity factors were estimated to determine crack-propagation direction. Also, various fatigue crack growth models were used to estimate crack-propagation life. Experiments were performed in Lewis' Spur Gear Fatigue Rig to validate predicted crack propagation results. Gears with various backup ratios were tested to validate crack-path predictions. Also, test gears were installed with special crack-propagation gages in the tooth fillet region to measure bending-fatigue crack growth. From both predictions and tests, gears with backup ratios (rim thickness divided by tooth height) of 3.3 and 1.0 produced tooth fractures, whereas a backup ratio of 0.3 produced rim fractures. For a backup ratio of 0.5, the experiments produced rim fractures and the predictions produced both rim and tooth fractures, depending on the initial geometry of the crack. Good correlation between predicted and measured crack growth was achieved when the fatigue crack-closure concept was introduced into the analysis. As the gear rim thickness decreased, the compressive cyclic stress in the gear-tooth fillet region increased. This retarded crack growth and increased the number of crack-propagation cycles to failure.

Source record↗

Grizzly: A Multi-scale and Multi-Physics Tool to Model Aging of Nuclear Power Plant Components

Grizzly is a multi-scale multi-physics tool being developed at Idaho National Laboratory (INL) as part of the US Department of Energy's Light Water Reactor Sustainability program to provide improved safety assessments of systems, components, and structures in nuclear power plants subjected to age-related degradation. Its goal is to provide an improved scientific basis for decisions surrounding license renewal, which would permit operation of commercial nuclear power plants beyond 60 years. Grizzly is based on INL's MOOSE framework, which enables multi-physics simulations in a massively parallel computing environment. The reactor pressure vessel (RPV) has been chosen as the initial application for Grizzly. The primary concern for the RPV is that it becomes increasingly susceptible to fracture initiation at the sites of pre-existing flaws over time. This is because exposure to irradiation and high temperatures embrittles the steel. Assessing the safety of an RPV under transient conditions involves simulations at multiple scales. At the engineering scale, strongly coupled equations of heat conduction and solid mechanics are solved to simulate the global response of the RPV to accident conditions. Sub-models are used to represent regions with pre-existing flaws and the stress intensity factors are evaluated from the domain integrals. Crack propagation is then determined using a model that provides the temperature and neutron fluence dependent fracture toughness of the RPV steel. The ability of Grizzly to provide accurate engineering scale estimates of RPV safety beyond 60 years of operation strongly relies on the predictability of the embrittlement model. Multiple models for embrittlement have been proposed, and the physically based empirical model is implemented in Grizzly. However, the formation of late blooming phases greatly reduces the confidence on the extrapolated values obtained from embrittlement model, which is further exacerbated by the absence of real field data for validation. Experimentally validated lower length scale models can significantly improve the predictability of the embrittlement model beyond the calibrated range and the development of such models is another ongoing effort in Grizzly. The modeling activity in Grizzly spans across different length scales, and can be divided into: (i) Irradiation induced microstructure evolution at the atomistic and single crystal length scale using molecular dynamics, atomistic kinetic Monte-Carlo, phase-field and rate theory; (ii) Effect of the irradiation induced defects on the flow stress and fracture processes at the polycrystalline scale using crystal plasticity. Subsequently, the prediction from these models can be used to obtain irradiation induced ductile-to-brittle transition temperature (DBTT) shifts from specimen-scale simulations; (iii) Global thermo-mechanical response of the RPV under normal and accident scenarios, and probabilistic risk analyses at the engineering scale using the DBTT shifts obtained from the lower length scale models. The item (i) has been discussed in a previous report. In this extended abstract an overview of items (ii) and (iii) is provided. The extended abstract summarizes the current status of the modeling effort under Grizzly. At the engineering scale, reduced order model development is underway using the statistical tool RAVEN. This will allow probabilistic analysis considering a wide range of flaw topologies in a computationally efficient manner. Coupling the irradiation induced defect growth predictions to crystal plasticity is also in progress. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Evaluating methods to reduce duration of near-threshold fatigue crack growth rate measurements for low-alloy steels in hydrogen gas

Measurement of the near-threshold fatigue crack growth rate (da/dN) vs. stress-intensity factor range (∆K) relationship in hydrogen gas is essential for maximizing the calculated design fatigue life of high-pressure hydrogen storage vessels. However, such measurements are rarely performed, since the low cyclic loading frequencies applied in standard practice lead to prohibitively protracted test durations. The objective of this study was to demonstrate two means for reducing test durations when measuring near-threshold da/dN vs. ΔK relationships under decreasing ΔK for low-alloy pressure vessel steels in hydrogen gas: 1) imposing steeper K-gradients relative to the recommended limits in standards such as ASTM E647, and 2) increasing cyclic loading frequency relative to typical values applied during fatigue crack growth testing of low-alloy steels in hydrogen gas. Recognizing that steeper K-gradients could amplify loading-history effects, test methods employing this approach were designed to mitigate such effects by either maintaining constant K max or gradually increasing the K-gradient as the threshold was approached. Although the varying K-gradient method was vulnerable to loading-history effects in the form of plasticity-induced crack closure, particularly at lower stress ratio (R) and higher starting K max values, these effects could be compensated by applying the adjusted compliance ratio (ACR) method. Here, it was demonstrated that steeper K-gradients in concert with increased cyclic loading frequency reduced the duration of near-threshold fatigue crack growth tests in hydrogen gas by more than 99% relative to standard practices.

Fatigue threshold↗

Elastic-plastic models for multi-site damage

This paper presents recent developments in advanced analysis methods for the computation of stress site damage. The method of solution is based on the p-version of the finite element method. Its implementation was designed to permit extraction of linear stress intensity factors using a superconvergent extraction method (known as the contour integral method) and evaluation of the J-integral following an elastic-plastic analysis. Coarse meshes are adequate for obtaining accurate results supported by p-convergence data. The elastic-plastic analysis is based on the deformation theory of plasticity and the von Mises yield criterion. The model problem consists of an aluminum plate with six equally spaced holes and a crack emanating from each hole. The cracks are of different sizes. The panel is subjected to a remote tensile load. Experimental results are available for the panel. The plasticity analysis provided the same limit load as the experimentally determined load. The results of elastic-plastic analysis were compared with the results of linear elastic analysis in an effort to evaluate how plastic zone sizes influence the crack growth rates. The onset of net-section yielding was determined also. The results show that crack growth rate is accelerated by the presence of adjacent damage, and the critical crack size is shorter when the effects of plasticity are taken into consideration. This work also addresses the effects of alternative stress-strain laws: The elastic-ideally-plastic material model is compared against the Ramberg-Osgood model.

Actis, Ricardo L.↗

An Improved Fracture Mechanics-Informed Multiscale Thermomechanical Damage Model for Ceramic Matrix Composites

This paper extends recent work done by the authors in modeling length scale-dependent damage behavior of ceramic matrix composites (CMCs) to include effects of local anisotropy introduced by matrix cracking. This model captures scale-dependent damage initiation and propagation behavior of the brittle matrix by employing internal state variable (ISV) theory within a multiscale modeling framework to obtain damaged matrix stress/strain constitutive relationships at each length scale. The damage ISV captures the effects of matrix cracking and growth by using fracture mechanics and the self-consistent scheme to determine the reduced stiffness of the cracked matrix. Matrix cracks, which activate when stress intensity factors near manufacturing induced cavities exceed the fracture toughness of the material, are assumed to be transversely isotropic in the plane of the crack, and matrix anisotropy occurs when the damaged stiffness tensor is rotated from the crack plane to the global axes. The crack progression and temporal evolution of the damage ISV are governed by fracture mechanics and crack growth kinetics. The model effectively captures first matrix cracking, which is the first significant deviation from linear elasticity. The nonlinear predictive capabilities of the material model are demonstrated for monolithic silicon carbide (SiC) and a 2D woven five-harness satin (5HS) carbon fiber SiC matrix (C/SiC) CMC.

Skinner, Travis↗

Modeling Three-Dimensional Fluid-Driven Propagation of Multiple Fractures using TOUGH-FEMM

Here, a novel numerical simulation tool named TOUGH-FEMM is presented and applied to model three-dimensional (3D) hydraulic fracturing in porous rock. The fluid flow in both fractures and porous rock is modeled using TOUGH2, which is a well-established code for analysis of multiphase and multi-component fluid flow. Rock deformations associated with fracture propagation are modeled using finite element-meshfree method (FEMM). FEMM is an approach to simulate fracture propagation without remeshing, in which the fracture path does not need to be predetermined. Fracture mechanics with mixed-mode stress intensity factors are employed to detect fracture instability and determine the direction of fracture propagation. TOUGH-FEMM is confirmed for modeling fluid-driven fracture propagation in 3D through a number of simulation examples, including modeling of hydraulic fracturing laboratory experiments and by comparison to independent numerical simulation results for multiple interacting hydraulic fractures at ten to hundred meter scale.

58 GEOSCIENCES↗

Quantitative In Situ Studies of Dynamic Fracture in Brittle Solids Using Dynamic X-ray Phase Contrast Imaging

Here, we demonstrate the use of X-ray phase contrast imaging with sub-microsecond temporal resolution to obtain quantitative visualization of dynamic fracture processes in brittle solids. We examine an amorphous solid (fused silica), a ceramic single crystal (single-crystal quartz), and a polycrystalline ceramic (boron carbide), in the form of single-edge notched specimens loaded using a three-point apparatus at nominal strain rates up to ~800 s -1 . We observe that the crack tip speed for boron carbide is relatively independent of mode I stress intensity factor rate ($\dot{K}$ I ) for these rates of loading, while that of fused silica and single-crystal quartz increases with $\dot{K}$ I . Further, for the amorphous and single crystal cases, we observe the development of a crack tip instability in the form of crack branching as the crack tip speed approaches 45% of the Rayleigh wave speed. This suggests that strain-rate-dependent mechanisms contribute to crack branching. Such mechanisms may, in turn, affect the macroscopic fracture properties of these materials.

36 MATERIALS SCIENCE↗

In situ high energy X-ray diffraction measurement of strain and dislocation density ahead of crack tips grown in hydrogen

The deformation fields near fatigue crack tips grown in hydrogen and in air were measured using high-energy x-ray diffraction. A larger magnitude of elastic strain was observed in the hydrogen case compared to the air case. The magnitude of elastic strain was quantified through an effective crack tip stress intensity factor. The dislocation profile ahead of the crack was probed via x-ray line broadening and electron back-scatter diffraction was used to assess the crack path (intergranular vs. transgranular). Ahead of the crack tip grown in hydrogen, an order of magnitude lower dislocation density, compared to a baseline density far from the crack, was observed. This decrease in dislocation density was not observed in the air case. These differences are discussed in terms of two leading hydrogen embrittlement mechanisms, Hydrogen Enhanced Localized Plasticity (HELP) and Hydrogen Enhanced Decohesion (HEDE). We have observed a decrease in transgranular cohesion (transgranular HEDE), as well as an increase in intergranular fracture. The measurements of dislocation activity support a model of a decrease in intergranular cohesion (intergranular HEDE) which is likely facilitated by the HELP mechanism. Here, this suggests that the increase in fatigue crack growth rate is due to a sum of the two effects of hydrogen, in which the crack grows faster in the transgranular fracture mode and faster due to an increase in a new mode of intergranular fracture. Published by Elsevier Ltd on behalf of Acta Materialia Inc.

36 MATERIALS SCIENCE↗

Investigation of dynamic fracture behavior of additively manufactured Al-10Si-Mg using high-speed synchrotron X-ray imaging

The dynamic tensile properties of additively manufactured (AM) and cast Al-10Si-Mg alloy were disccused using high-speed synchrotron X-ray imaging coupled with a modified Kolsky bar apparatus. A controlled tensile loading (strain rate ≈ 750 s -1 ) was applied using the Kolsky bar apparatus and the deformation and fracture behavior were recorded using the high-speed X-ray imaging setup. The CT and high-speed imaging results worked together to identify the location of the critical flaw and to capture the dynamics of crack propagation. In all experiments, the critical flaw was located on the surface of each specimen. The AM specimens displayed significantly higher crack propagation speed, yield strength, ultimate tensile strength, strain hardening coefficient, and yet lower ductility compared to the cast specimens under dynamic tension. Although the strength values were higher for the AM specimens, the critical mode I stress intensity factors were comparable for both specimens. The microstructures of the samples were characterized by synchrotron X-ray computed tomography (CT) and scanning electron microcopy. The correlation between the dynamic fracture behavior of the samples and the microstructure of the samples is analyzed and discussed.

36 MATERIALS SCIENCE↗

An integrated numerical model for coupled poro-hydro-mechanics and fracture propagation using embedded meshes

Integrated models for fluid-driven fracture propagation and general multiphase flow in porous media are valuable to the study and engineering of several systems, including hydraulic fracturing, underground disposal of waste, and geohazard mitigation across such applications. This work extends the coupled model multiphase flow and poromechanical model of Ren et al. (2018) to admit fracture propagation (FP). The coupled XFEM-EDFM scheme utilizes a separate fracture mesh that is embedded on a static background mesh. The onset and dynamics of fracture propagation are governed by the equivalent stress intensity factor (SIF) criterion. A domain-integral method (J integral) is applied to compute this information. Additionally, an adaptive time-marching scheme is proposed to rapidly restrict and grow temporal resolution to match the underlying time-scales. The proposed model is verified with analytical solutions, and shows the capability to accurately and adaptively co-simulate fluid transport and deformation as well as the propagation of multiple fractures.

42 ENGINEERING↗

Hydrogen accelerated fatigue crack growth of friction stir welded X52 steel pipe

Friction stir welded steel pipelines were tested in high pressure hydrogen gas to examine the effects of hydrogen accelerated fatigue crack growth. Fatigue crack growth rate (da/dN) vs. stress-intensity factor range (ΔK) relationships were measured for an X52 friction stir welded pipe tested in 21 MPa hydrogen gas at a frequency of 1 Hz and R = 0.5. Tests were performed on three regions: base metal (BM), center of friction stir weld (FSW), and 15 mm off-center of the weld. For all three material regions, tests in hydrogen exhibited accelerated fatigue crack growth rates that exceeded an order of magnitude compared to companion tests in air. Among tests in hydrogen, fatigue crack growth rates were modestly higher in the FSW than the BM and 15 mm off-center tests. Select regions of the fracture surfaces associated with specified ΔK levels were examined which revealed intergranular fracture in the BM and 15 mm off-center specimens but an absence of intergranular features in the FSW specimens. In conclusion, the X52 friction stir weld and base metal tested in hydrogen exhibited fatigue crack growth rate relationships that are comparable to those for conventional arc welded steel pipeline of similar strength found in the literature.

08 HYDROGEN↗

On the fatigue crack growth behavior of Ti–10V–2Fe–3Al in gaseous hydrogen

Here, the fatigue crack growth behavior of Ti–10V–2Fe–3Al in gaseous hydrogen (H 2 ) was assessed through comparative experiments conducted in laboratory air and 8.3 MPa H 2 . The measured fatigue crack growth rate (da/dN) versus applied stress intensity factor range (ΔK) relationships and observed fracture morphologies for laboratory air and H 2 were comparable up to ΔK ≈ 6.9 MPa√m, when tested at a load ratio of 0.1 and frequency of 10 Hz. At higher ΔK values, significant crack deflection and subsequent catastrophic failure occurred in the specimen tested in H 2 . This degradation was not observed in a specimen pre-exposed to 8.3 MPa H 2 for 96 h and then immediately tested in laboratory air. X-ray diffraction of the failed H 2 -tested specimen revealed that the material remnants were predominantly composed of TiH 2 , suggesting that hydride formation was the catalyst for catastrophic failure in H 2 . The mechanistic implications of these results and their impact on current material compatibility assessments for Ti alloys in hydrogen service are then discussed.

08 HYDROGEN↗

Grain-boundary fracture mechanisms in Li 7 La 3 Zr 2 O 12 (LLZO) solid electrolytes: When phase transformation acts as a temperature-dependent toughening mechanism

Garnet-type, solid electrolytes, such as Li 7 La 3 Zr 2 O 12 (LLZO), are a promising alternative to liquid electrolytes for lithium-metal batteries. However, such solid-electrolyte materials frequently exhibit undesirable lithium (Li) metal plating and fracture along grain boundaries. In this work, we employ atomistic simulations to investigate the mechanisms and key fracture properties associated with intergranular fracture along one such boundary. Our results show that, in the case of a Σ5 (310) grain boundary, this boundary exhibits brittle fracture behavior, i.e. the absence of dislocation activity ahead of the propagating crack tip, accompanied with a decrease in work of separation, peak stress, and maximum stress intensity factor as the temperature increases from 300 K to 1500 K. As the crack propagates, we predict two temperature-dependent Li clustering regimes. For temperatures at or below 900 K, Li tends to cluster in the bulk region away from the crack plane driven by a void-coalescence mechanism concomitant a simultaneous cubic-to-tetragonal phase transition. The tetragonalization of LLZO in this temperature regime acts as an emerging toughening mechanism. At higher temperatures, this phase transition mechanism is suppressed leading to a more uniform distribution of Li throughout the grain-boundary system and lower fracture properties as compared to lower temperatures.

36 MATERIALS SCIENCE↗