Search NASA⌕ Search

SEARCH · Search NASA

Results for “Scanning electron microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Mitigating Battery Cell Failure: Role of Ag‐Nanoparticle Fillers in Solid Electrolyte Dendrite Suppression

Abstract The development of solid‐state batteries (SSBs) with lithium Li metal anodes holds significant promise for enhancing the energy density and safety of next‐generation energy storage systems. However, their commercialization is hindered by challenges related to Li dendrite formation, which can lead to short circuits and battery failure. In this study, the role of Ag nanoparticles embedded within solid electrolytes (SE) is investigated in suppressing dendrite propagation. The results demonstrate that Ag nanoparticles effectively mitigate two key failure mechanisms: (1) dendrite growth within porous networks at low current densities and (2) stress intensification‐induced SE fracture at higher current densities (12 mA cm −2 ). Ex situ characterization using focused‐ion beam – scanning electron microscopy (FIB–SEM) and energy dispersive X‐ray spectroscopy (EDS,) reveals that Ag nanoparticles migrate alongside advancing Li dendrites, promoting homogeneous dendrite growth and reducing the likelihood of localized stress concentrations. Additionally, the incorporation of Ag nanoparticles is shown to facilitate a more uniform Li distribution toward the anode side, which can potentially enable the use of higher charging rates in SSBs. This study provides a new perspective on Li dendrite suppression and presents new opportunities for enhancing the performance and safety of SSBs.

Diallo, Mouhamad Said↗
DOE OSTI2022

Overcoming the Intrinsic Limitations of Fast Charging Lithium‐Ion Batteries Using Integrated Acoustic Streaming

A lithium‐ion battery's maximum charge rate and energy density are intrinsically limited by the ion diffusion rate in the electrolyte. Most research focuses on materials science solutions to this problem, with gradual improvement over the years. A mechanical solution is proposed to integrate an MHz‐order frequency surface acoustic wave (SAW) device into an existing 1.8 Ah multilayered Li‐ion pouch cell to enhance the ion diffusion rate and the overall battery performance. Both the charging rate and cycling lifetime are improved from SAW. At a 6C (10 min) charge and C/3 discharge rate, typical of electric vehicle applications, integrating SAW into the Li‐ion cell doubles the energy density and maintains at least 72% of the battery's initial capacity after 2000 cycles. Moreover, using SAW quantifiably reduces battery degradation in these conditions as determined by optical imaging, scanning electron microscopy, X‐ray diffraction, and neutron diffraction. The use of SAW appears to offer a method to avoid undesirable Li metal plating on the graphite anode during charging, and leads to a much longer battery lifetime and good charge capacity, all despite rapid charging.

Huang, An↗
DOE OSTI2021

Population balance modeling of polyurethane foam formation with pressure‐dependent growth kernel

Abstract Polyurethane foams are widely used materials often chosen for their useful characteristics such as low thermal conductivity, ease of application, and high strength‐to‐weight ratios. Computational models are needed to predict the dynamics of the flow and expansion, and the resulting material properties, to improve manufacturing processes. In this paper, a model for PMDI, a water‐blown polyurethane foam, is presented. By extending a kinetics‐based approach by adding bubble‐scale information via a population balance equation (PBE) using the quadrature method of moments, we can track bubble size distributions during foaming. We present results from a three‐dimensional computational fluid dynamics model using arbitrary Lagrangian–Eulerian interface tracking implemented in finite element software. The model compares favorably with experimental data, including dynamics, bubble distributions measured by both camera and diffusion wave spectroscopy, and post‐test bubble size from scanning electron microscopy and density measurements from x‐ray computed tomography.

Ortiz, Weston↗
DOE OSTI2023

Migration and Precipitation of Platinum in Anion‐Exchange Membrane Fuel Cells

Abstract Despite the recent progress in increasing the power generation of Anion‐exchange membrane fuel cells (AEMFCs), their durability is still far lower than that of Proton exchange membrane fuel cells (PEMFCs). Using the complementary techniques of X‐ray micro‐computed tomography (CT), Scanning Electron Microscopy (SEM) and Energy Dispersive X‐ray (EDX) spectroscopy, we have identified Pt ion migration as an important factor to explain the decay in performance of AEMFCs. In alkaline media Pt +2 ions are easily formed which then either undergo dissolution into the carbon support or migrate to the membrane. In contrast to PEMFCs, where hydrogen cross over reduces the ions forming a vertical “Pt line” within the membrane, the ions in the AEM are trapped by charged groups within the membrane, leading to disintegration of the membrane and failure. Diffusion of the metal components is still observed when the Pt/C of the cathode is substituted with a FeCo−N−C catalyst, but in this case the Fe and Co ions are not trapped within the membrane, but rather migrate into the anode, thereby increasing the stability of the membrane.

Raut, Aniket↗
DOE OSTI2023

Migration and Precipitation of Platinum in Anion–Exchange Membrane Fuel Cells

Despite the recent progress in increasing the power generation of Anion-exchange membrane fuel cells (AEMFCs), their durability is still far lower than that of Proton exchange membrane fuel cells (PEMFCs). Using the complementary techniques of X-ray micro-computed tomography (CT), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) spectroscopy, we have identified Pt ion migration as an important factor to explain the decay in performance of AEMFCs. In alkaline media Pt+2 ions are easily formed which then either undergo dissolution into the carbon support or migrate to the membrane. In contrast to PEMFCs, where hydrogen cross over reduces the ions forming a vertical “Pt line” within the membrane, the ions in the AEM are trapped by charged groups within the membrane, leading to disintegration of the membrane and failure. Furthermore, diffusion of the metal components is still observed when the Pt/C of the cathode is substituted with a FeCo–N–C catalyst, but in this case the Fe and Co ions are not trapped within the membrane, but rather migrate into the anode, thereby increasing the stability of the membrane.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Preparation of pH ‐responsive cellulose nanofibril/sodium alginate based hydrogels for drug release

Abstract In this work, hydrogels composed of cellulose nanofibril (CNF) and sodium alginate (SA) were prepared as a pH‐responsive release system by controlling the amount of CNF and SA. Scanning electron microscopy, thermogravimetric analysis, and swelling rate methods were used to characterize. The results showed that when the mass ratio of CNF to SA was 2:1, CNF/SA hydrogels with better morphology were obtained. Due to the deprotonation or protonation of calcium alginate, as the pH changing from 1.5 to 11.0, the swelling ratio increased from 7 times to 19 times compared with its dry weight. The drug release behaviors of the CNF/SA hydrogels using ibuprofen (IBU) as a model drug were investigated in vitro. The release of IBU was faster in alkaline conditions and slower in acidic conditions. The drug release mechanism under pH stimulation could be interpreted by the Fickian diffusion and erosion effect based on Korsmeyer‐Peppas model.

Li, Yuhang↗
DOE OSTI2022

Interlaminar improvement of carbon fiber/epoxy composites via fluorine‐containing high‐epoxy‐value sizing agent

Abstract To improve the interfacial bonding effect of carbon fibers (CFs) and epoxy resins, we prepared a fluorine‐containing high‐epoxy‐value sizing agent (named TS) in this article. It is an emulsion with a more uniform particle size distribution and higher stability better than a commercial Takemoto sizing agent. In addition, sulfonic acid groups can improve the hydrophilicity of the TS, and the presence of epoxy groups enhances the wettability between CFs and the matrix. The properties of the sizing agents were examined by Fourier transform infrared spectroscopy, dynamic light scattering, and thermogravimetric analysis. The sized CFs were evaluated by scanning electron microscopy, x‐ray photoelectron spectroscopy, monofilament tensile test, and dynamic contact angle. Afterward, CF/epoxy composites were prepared, and their fracture morphology and interlaminar shear strength (ILSS) were examined. Results indicated that the TS sizing significantly increased the content of activated carbon on the surface of the CFs and improved the bonding effect between the fiber and the matrix. After TS was sized, the ILSS increased from 49.64 to 58.74 MPa, 18.34% higher than unsized CF/epoxy composites, showing the prominent interfacial reinforcement better than commercial Takemoto.

Qiu, Zhijie↗
DOE OSTI2020

Briquetting characteristics of woody and herbaceous biomass blends: Impact on physical properties, chemical composition, and calorific value

Abstract Intercropping (or polyculture) is gaining a lot of interest as it increases yields, allows better utilization of resources (water and nutrients), and provides better land management. The objective of this study is to understand the briquetting characteristics of woody and herbaceous biomass blends, which might result from intercropping. Tests were conducted on blends of lodgepole pine, switchgrass, and corn stover biomass using three hammer mill screen sizes (i.e., 4.8, 12.7, and 19.05 mm), three blend moistures (12%, 15%, and 18%, w.b.), and two‐ and three‐blend ratios (i.e., 1:1 and 1:1:1) using a pilot‐scale hydraulic briquette press. The briquette properties, such as unit and bulk density, durability rating after 5 days of storage (as they tend to attain stable density), and the energy consumption of the process were measured. The results indicate that moisture content of 12% and 15% (w.b.) and smaller hammer mill screen size of 4.8 mm increased the unit and bulk densities to >750 and >430 kg/m 3 and moisture content (15% and 18% (w.b.)) and hammer mill screen size of 12.7 and 19.05 mm produced briquettes with durability rating values of >95%. The higher moisture content of 18% (w.b.) and the hammer mill screen size of 12.7 and 19.05 mm had the highest energy consumption. The proximate and ultimate analysis showed that energy content improved by blending lodgepole pine with both corn stover and switchgrass and also showed increased calorific value and reduced ash content. Scanning electron microscopy micrographs showed interlocking of particles and cracks in the briquettes. © 2020 Society of Chemical Industry and John Wiley & Sons, Ltd

Tumuluru, Jaya Shankar↗
DOE OSTI2021

Screening of alkali-assisted storage conditions to define the operational window of deacetylation within storage systems in the bioenergy supply chain

Overcoming biomass heterogeneity and associated recalcitrance to thermal, chemical, and enzymatic depolymerization is a necessary but challenging aspect of valorizing lignocellulosic biomass to fuels and chemicals. Here, this study explores how this recalcitrance can be reduced during the supply chain unit operation of storage, which is required for seasonally harvested agricultural residues to maintain constant throughput at a biorefinery. In this work, partial alkali pretreatment was performed just prior to corn stover entering storage, which had the benefit of providing a high pH environment entering storage such that soluble sugars were preserved and saponified acetyl groups in hemicellulose. This work investigated a range of viable conditions where saponification and preservation occur simultaneously by varying the moisture content (40% and 60%) and concentrations of sodium hydroxide (low and high) during aerobic and anaerobic storage. Anaerobic conditions preserved overall dry matter below 5% in the three scenarios evaluated, and the highest alkali loading solubilized up to 15% lignin, 18% xylan, and 50% of acetate, meanwhile doubling the extractable components. Scanning electron microscopy images highlighted potential physical impacts including cell-wall disruption near vascular bundles, pitting within parenchyma cells, and cell-wall distortion. Techno-economic assessment indicated that this storage approach and associated logistics system is economically competitive with a conventional approach using low-moisture bales.

09 BIOMASS FUELS↗
DOE OSTI2026

Influence of Air and Ethanol Dehydration on Structure, Behavior, and Function of Type I Collagen Scaffolds

Ethanol dehydration is a common step in both scaffold manufacturing and tissue processing, yet the influence of ethanol on collagen is not well understood. This study examined the effects of dehydration, via ethanol treatment and air drying, on collagen structure, behavior, mechanics, and rehydration capacity. Multiple material characterization methods were used including Fourier Transform infrared spectroscopy (FTIR), Raman spectroscopy, scanning electron microscopy, thermogravimetric analysis, small/medium angle x‐ray scattering, volumetric swelling analysis, and tensile testing. Ethanol dehydration removed bulk water from scaffolds, making them stronger and stiffer, but also showed loss of molecular water. This molecular water appears to act as a collagen stabilizer, resulting in less thermally stable scaffolds. The loss of molecular water is also evident in the molecular d‐spacing. Secondary structure of scaffolds was also altered by ethanol, resulting in significantly enhanced rehydration capacity. Bulk water, both before and after rehydration, largely determined mechanical properties, which did not correlate with other structural measures such as FTIR. While rehydration largely returned collagen spacing to pre‐ethanol treated state, structural alterations seen in FTIR cannot be recovered. These results have implications for not only collagen scaffolds, but in many tissue engineering and processing applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Influence of Water, Vacuum, and Temperature on Surface Conditions of a Zeolite‐based Molecular Sieve

Molecular sieves such as zeolite-based materials are ubiquitous in industrial separation processes. However, there is a significant gap in understanding the surface properties and adsorption mechanisms for commercial zeolites, as most research focuses on pure zeolite powders rather than industrially relevant forms. Here, this work addresses this gap in understanding by employing advanced characterization techniques, including positron annihilation spectroscopy, X-ray diffraction, scanning electron microscopy, X-ray fluorescence spectroscopy, X-ray photoelectron spectroscopy, liquid nitrogen sorption, and Fourier-transform infrared spectroscopy, to investigate the adsorption and desorption behavior of water in commercial zeolite 13X. Our research reveals insights into the pore-filling mechanisms, the impact of material binders on adsorption properties, and the dynamics of hydration and drying processes for zeolites. Monitoring changes on a minute scale allowed the distinction between fast and slow processes leading to sample drying. The identification of positronium bound to Na + ions indicated that water molecules remain in the vicinity of Na + ions after air-drying zeolite 13X. These findings highlight the importance of various environmental conditions in restoring zeolite properties to baseline after hydration, with significant implications for optimizing industrial processes. This work sets the direction for further research aimed at developing more efficient and robust separation techniques.

Beads Binder↗
DOE OSTI2023

Photoexcitation of Fe 3 O Nodes in MOF Drives Water Oxidation at pH=1 When Ru Catalyst Is Present

Abstract Artificial photosynthesis strives to convert the energy of sunlight into sustainable, eco‐friendly solar fuels. However, systems with light‐driven water oxidation reaction (WOR) at pH=1 are rare. Broadly used [Ru(bpy) 3 ] 2+ (bpy=2,2’‐bipyridine) photosensitizer has a fixed +1.23 V potential which is insufficient to drive most water oxidation catalysts (WOCs) in acid, while Fe 2 O 3 , featuring the highly oxidizing holes, is not stable at low pH. Here, the key examples of Fe‐based metal–organic framework (MOF) water oxidation photoelectrocatalysts active at pH=1 are presented. Fe‐MIL‐126 and Fe MOF‐dcbpy structures were formed with 4,4’‐biphenyl dicarboxylate (bpdc), 2,2’‐bipyridine‐5,5’‐dicarboxylate (dcbpy) linkers and their mixtures. Presence of dcbpy linkers allows integration of metal‐based catalysts via coordination to 2,2’‐bipyridine fragments. Fe‐based MOFs were doped with Ru‐based precursors to achieve highly active MOFs bearing [Ru(bpy)(dcbpy)(H 2 O) 2 ] 2+ WOC. Materials were analyzed with X‐ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infra‐red (FTIR) spectroscopy, resonance Raman, X‐ray absorption spectroscopy, fs optical pump‐probe, electron paramagnetic resonance (EPR), diffuse reflectance and electric conductivity measurements and were modeled by band structure calculations. It is shown that under reaction conditions, Fe III and Ru III oxidation states are present, indicating rate‐limiting electron transfer in MOF. Fe 3 O nodes emerge as photosensitizers able to drive prolonged O 2 evolution in acid. Further developments are possible via MOF's linker modification for enhanced light absorption, electrical conductivity, reduced MOF solubility in acid, Ru‐WOC modification for faster WOC catalysis, or Ru‐WOC substitution to 3d metal‐based systems. The findings give further insight for development of light‐driven water splitting systems based on Earth‐abundant metals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Chemical and Electrochemical Characterization of Hot–Pressed Li 6 PS 5 Cl Solid State Electrolyte: Operating Pressure–Invariant High Ionic Conductivity

Sulfide solid state electrolytes (SSE) are among the most promising materials in the effort to replace liquid electrolytes, largely due to their comparable ionic conductivities. Among the sulfide SSEs, Argyrodites (Li 6 PS 5 X, X=Cl, Br, I) further stand out due to their high theoretical ionic conductivity (~1×10 –2 S cm –1 ) and interfacial stability against reactive metal anodes such as lithium. Generally, solid state electrolyte pellets are pressed from powder feedstock at room temperature, however, pellets fabricated by cold pressing consistently result in low bulk density and high porosity, facilitating interfacial degradation reactions and allowing dendrites to propagate through the pores and grain boundaries. Here, we demonstrate the mechanical and electrochemical implications of hot-pressing standalone LPSCl SSE pellets with near-theoretical ionic conductivity, superior cycling performance, and enhanced mechanical stability. X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and x-ray diffraction spectroscopy (XRD) analysis reveal no chemical changes to the Argyrodite surface after hot pressing up to 250°C. Furthermore, we use electrochemical impedance spectroscopy (EIS) to understand mechanical stability of Argyrodite SSE pellets as a function of externally applied pressure, demonstrating for the first time pressed standalone Argyrodite pellets with near-theoretical conductivities at external pressures below 14 MPa.

25 ENERGY STORAGE↗
DOE OSTI2021

Evolution of eggshell structure in relation to nesting ecology in non-avian reptiles

Amniotic eggs are multifunctional structures that enabled early tetrapods to colonize the land millions of years ago, and are now the reproductive mode of over 70% of all terrestrial amniotes. Eggshell morphology is at the core of animal survival, mediating the interactions between embryos and their environment, and has evolved into a massive diversity of forms and functions in modern reptiles. These functions are critical to embryonic survival and may serve as models for new antimicrobial and/or breathable membranes. However, we still lack critical data on the basic structural and functional properties of eggs, particularly of reptiles. Here, we first characterized egg shape, shell thickness, porosity, and mineralization of eggs from 91 reptile species using optical images, scanning electron microscopy, and micro computed tomography, and collected data on nesting ecology from the literature. We then used comparative analyses to test hypotheses on the selective pressures driving their evolution. We hypothesized that eggshell morphology has evolved to protect shells from physical damage and desiccation, and, in support, found a positive relationship between thickness and precipitation, and a negative relationship between porosity and temperature. Although mineralization varied extensively, it was not correlated with nesting ecology variables. Ancestral state reconstructions show thinning and increased porosity over evolutionary time in squamates, but the opposite in turtles and crocodilians. Egg shape, size, porosity and calcification were correlated, suggesting potential structural or developmental tradeoffs. This study provides new data and insights into the morphology and evolution of reptile eggs, and raises numerous questions for additional research.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Dynamics of High Molecular Weight Cylindrical and Lamellar Block Copolymers with X‐ray Photon Correlation Spectroscopy

Here, the structure and dynamics of polystyrene (PS)-b-poly(ethylene oxide) block copolymers (BCPs) are studied. The BCPs exhibit microphase-separated cylindrical and lamellar morphologies. Structural dynamics are measured with X-ray photon correlation spectroscopy in the small-angle regime. Morphologies and domain sizes are evaluated using small-angle X-ray scattering (SAXS), scanning electron microscopy, and atomic force microscopy. Different solvent processing conditions are investigated. Grain sizes evaluated using SAXS are found to depend on processing only for the rubbery majority BCP. The structural relaxation times are examined as a function of PS volume fraction, temperature, morphology, and structural sizes. Well above the glass transition temperature (T g ) of PS, all samples exhibit stretched autocorrelation decays and diffusive dynamics. Near T g of PS, the dynamics of all samples are anomalous with compressed autocorrelation decays and hyperdiffusive dynamics. This transition occurs at 153 °C or 1.13 T g of PS. In the diffusive regime (at high temperature), structural relaxation times are dependent on the processing method. Near PS T g (at low temperature), structural relaxation times scale with the PS volume fraction. Structural relaxation times do not correlate with grain size, indicating that the out-of-equilibrium state of PS dominates the structural dynamics of these strongly phase-segregated BCPs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Data‐Driven Engineering of Thermostable Collagen‐Mimetic Peptoid Triple Helices

Collagen-mimetic peptides (CMPs) are engineered molecules designed to replicate the triple-helical structure of natural collagen. A repeating x–y-Gly sequence is the defining motif of CMPs and is critical to their triple-helical structure and stability. Substitutions to the residues occupying the x and y positions present a means to modulate the CMP structure and properties. Peptoid residues—N-substituted glycine derivatives—present an attractive potential substitution due to their thermal stability, proteolytic resistance, biocompatibility, and diverse palette of non-natural side chains, but also tend to introduce a high degree of backbone flexibility that can diminish the stability of the triple helix. In this work, we report a computational active learning cycle comprising molecular dynamics simulation, Gaussian process regression, and Bayesian optimization to computationally identify a number of promising peptoid substitutions predicted to stabilize the desired quaternary structure through side chain interactions and produce stable peptoid-based collagen-like triple helices. To experimentally test the computational predictions, a top candidate identified by the screen was synthesized and imaged using scanning electron microscopy to resolve fibril-like bundles consistent with collagen-like triple helices. This work predicts a number of CMP peptoid substitutions capable of forming stable triple-helical structures, presents a generalizable design strategy for engineering desired peptoid structures, and opens new avenues for the design of peptoid-based biomimetic materials.

active learning↗
DOE OSTI2019

Fabrication of diatomite‐based microencapsulated flame retardant and its improved fire safety of unsaturated polyester resin

To achive excellent fire resistance, new microcapsule flame retardants (DMCAD and DMPPD) were prepared using 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide combined with melamine cyanurate or melamine polyphosphate as the shell material and diatomite as the core material. The successful assembly of DMCAD and DMPPD was detailed characterized by Fourier transform infrared (FT‐IR) spectra, X‐ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). Meanwhile, the flame retardancy and thermal stability of the unsaturated polyester resin (UPR)/DMCAD and UPR/DMPPD composites were also studied. The addition of DMCAD and DMPPD effectively improves the flame retardance properties of UPR, and the effect of DMPPD was better. The limiting oxygen index (LOI) of UPR/DMPPD‐3 increased by 11.6% when compared with that of UPR, and the sample achieved V‐0 rating. Moreover, the peak heat release rate (pHRR) and the total heat release (THR) rate of UPR/DMPPD‐3 were reduced by 67% and 26%, respectively. Under nitrogen condition and air condition, UPR/DMPPD showed better thermal stability and char‐forming ability from the thermogravimetric (TG) results. Residual char of the UPR composites was systematically analyzed with SEM and XPS. Finally, the flame retardant mechanism of DMPPD was proposed.

Chen, Gang↗