Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stability and transition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Heat Sinking, Cross Talk, and Temperature Stability for Large, Close-Packed Arrays of Microcalorimeters

We are developing large, close-packed arrays of x-ray transition-edge sensor (TES) microcalorimeters. In such a device, sufficient heat sinking is important to to minimize thermal cross talk between pixels and to stabilize the bath temperature for all pixels. We have measured cross talk on out 8 x 8 arrays and studied the shape and amount of thermal crosstalk as a function of pixel location and efficiency of electrothermal feedback. In this presentation, we will compare measurements made on arrays with and without a backside, heat-sinking copper layer, as well as results of devices on silicon-nitride membranes and on solid substrates, and we will discuss the implications for energy resolution and maximum count rate. We will also discuss the dependence of pulse height upon bath temperature, and the measured and required stability of the bath temperature.

Imoto, Naoko↗
NASA NTRS1992

A new approach for the calculation of transitional flows

In spite of many attempts at modeling natural transition, it has not been possible to predict the streamwise intensities. A procedure is developed which incorporates some results of linear stability theory into one-equation and stress model formulations. The stresses resulting from fluctuations in the transitional region have turbulent, laminar (nonturbulent) and large eddy components. Comparison with Schubauer and Klebanoff's experiments have shown that the nonturbulent and large eddy components have a large influence on the streamwise intensities and little influence on the shear stress. Finally, predictions of the one-equation model were as good as those obtained by the stress model.

Young, T. W.↗
NASA NTRS1984

The absence of convective stability in incongruent crystal growth on Earth

It is often assumed that convection can be excluded in materials processing by avoiding horizontal temperature gradients, and employing top-heating and horizontal interfaces. Model calculations for vapor transport processes show that this supposition holds only for strictly congruent vapor-solid transitions. This result can be generalized to all fluid-solid phase transitions. Due to the omnipresence of impurity segregation, it is concluded that convective stability is practically unattainable in materials processing on Earth.

Rosenberger, F. E.↗
NASA NTRS2000

NASA/FAA Tailplane Icing Program: Flight Test Report

This report presents results from research flights that explored the characteristics of an ice-contaminated tailplane using various simulated ice shapes attached to the leading edge of the horizontal tailplane. A clean leading edge provided the baseline case, then three ice shapes were flown in order of increasing severity. Flight tests included both steady state and dynamic maneuvers. The steady state points were 1G wings level and steady heading sideslips. The primary dynamic maneuvers were pushovers to various G-levels; elevator doublets; and thrust transitions. These maneuvers were conducted for a full range of flap positions and aircraft angle of attack where possible. The analysis of this data set has clearly demonstrated the detrimental effects of ice contamination on aircraft stability and controllability. Paths to tailplane stall were revealed through parameter isolation and transition studies. These paths are (1) increasing ice shape severity, (2) increasing flap deflection, (3) high or low speeds, depending on whether the aircraft is in a steady state (high speed) or pushover maneuver (low speed), and (4) increasing thrust. The flight research effort was very comprehensive, but did not examine effects of tailplane design and location, or other aircraft geometry configuration effects. However, this effort provided the role of some of the parameters in promoting tailplane stall. The lessons learned will provide guidance to regulatory agencies, aircraft manufacturers, and operators on ice-contaminated tailplane stall in the effort to increase aviation safety and reduce the fatal accident rate.

Ratvasky, Thomas P.↗
NASA NTRS1957

Some Effects of Bluntness on Boundary-Layer Transition and Heat Transfer at Supersonic Speeds

Large downstream movements of transition observed when the leading edge of a hollow cylinder or a flat plate is slightly blunted are explained in terms of the reduction in Reynolds number at the outer edge of the boundary layer due to the detached shock wave. The magnitude of this reduction is computed for cones and wedges for Mach numbers to 20. Concurrent changes in outer-edge Mach number and temperature occur in the direction that would increase the stability of the laminar boundary layer. The hypothesis is made that transition Reynolds number is substantially unchanged when a sharp leading edge or tip is blunted. This hypothesis leads to the conclusion that the downstream movement of transition is inversely proportional to the ratio of surface Reynolds number with blunted tip or leading edge to surface Reynolds number with sharp tip or leading edge. The conclusion is in good agreement with the hollow-cylinder result at Mach 3.1.

Moeckel, W E↗
NASA NTRS1981

Perfluoroether triazine elastomers

The synthesis of high performance elastomers with the high thermal stability and chemical, inertness of perfluoroalkylene triazine and a low glass transition temperature is discussed. Perfluorether triazine elastomers were proposed as potentially superior. It is concluded that the difficulties experienced in fluoroalkytriazine elastomer synthesis can be overcome by a four-step reaction process involving chain extension, triazine ring closure, crosslinking, and elastomer curing. Molecular weight can be controlled in the initial polymer formation so that elastomer modulus can be determined. The final product elastomers exhibit a useful elastomeric range of approximately 45 to 325 C with an oxidative stability superior to other broad range elastomers.

Korus, R. A.↗
NASA NTRS1958

Hovering and Transition Flight Tests of a 1/5-Scale Model of a Jet-Powered Vertical-Attitude VTOL Research Airplane

An experimental investigation has been made to determine the dynamic stability and control characteristics of a 1/5-scale flying model of a jet-powered vertical-attitude VTOL research airplane in hovering and transition flight. The model was powered with either a hydrogen peroxide rocket motor or a compressed-air jet exhausting through an ejector tube to simulate the turbojet engine of the airplane. The gyroscopic effects of the engine were simulated by a flywheel driven by compressed-air jets. In hovering flight the model was controlled by jet-reaction controls which consisted of a swiveling nozzle on the main jet and a movable nozzle on each wing tip; and in forward flight the model was controlled by elevons and a rudder. If the gyroscopic effects of the jet engine were not represented, the model could be flown satisfactorily in hovering flight without any automatic stabilization devices. When the gyroscopic effects of the jet engine were represented, however, the model could not be controlled without the aid of artificial stabilizing devices because of the gyroscopic coupling of the yawing and pitching motions. The use of pitch and yaw dampers made these motions completely stable and the model could then be controlled very easily. In the transition flight tests, which were performed only with the automatic pitch and yaw dampers operating, it was found that the transition was very easy to perform either with or without the engine gyroscopic effects simulated, although the model had a tendency to fly in a rolled and sideslipped attitude at angles of attack between approximately 25 and 45 deg because of static directional instability in this range.

Smith, Charles C., Jr.↗
NASA NTRS1961

Hovering and Transition Flight Tests of a 1/5-Scale Model of a Jet-Powered Vertical-Attitude VTOL Research Airplane

An experimental investigation has been made to determine the dynamic stability and control characteristics of a 1/5-scale flying model of a jet-powered vertical-attitude VTOL research airplane in hovering and transition flight. The model was powered with either a hydrogen peroxide rocket motor or a compressed-air jet exhausting through an ejector tube to simulate the turbojet engine of the airplane. The gyroscopic effects of the engine were simulated by a flywheel driven by compressed-air jets. In hovering flight the model was controlled by jet-reaction controls which consisted of a swiveling nozzle on the main jet and a movable nozzle on each wing tip; and in forward flight the model was controlled by elevons and a rudder. If the gyroscopic effects of the jet engine were not represented, the model could be flown satisfactorily in hovering flight without any automatic stabilization devices. When the gyroscopic effects of the jet engine were represented, however, the model could not be controlled without the aid of artificial stabilizing devices because of the gyroscopic coupling of the yawing and pitching motions. The use of pitch and yaw dampers made these motions completely stable and the model could then be controlled very easily. In the transition flight tests, which were performed only with the automatic pitch and yaw dampers operating, it was found that the transition was very easy to perform either with or without the engine gyroscopic effects simulated, although the model had a tendency to fly in a rolled and sideslipped attitude at angles of attack between approximately 25 deg and 45 deg because of static directional instability in this range.

Smith, Charles C., Jr.↗
NASA NTRS2018

Instability Wave–Streak Interactions in a High Mach Number Boundary Layer at Flight Conditions

The interaction of stationary streaks undergoing nonmodal growth with modally unstable instability waves in a hypersonic boundary-layer flow is studied using numerical computations. The geometry and flow conditions are selected to match a relevant trajectory location from the ascent phase of the HIFiRE-1 flight experiment; namely, a 7 degree half-angle, circular cone with 2.5 mm nose radius, freestream Mach number equal to 5.30, unit Reynolds number equal to 13.42 m -1 , and wall-to-adiabatic temperature ratio of approximately 0.35 over most of the vehicle. This paper investigates the nonlinear evolution of initially linear optimal disturbances that evolve into finite-amplitude streaks, followed by an analysis of the modal instability characteristics of the perturbed, streaky boundary-layer flow. The investigation is performed with stationary direct numerical simulations (DNS) and plane-marching parabolized stability equations (PSE), in conjunction with partial-differential-equation-based planar eigenvalue analysis. The overall effect of streaks is to reduce the peak amplification factors of instability waves, indicating a possible downstream shift in the onset of laminar-turbulent transition. The present study confirms previous findings that the mean flow distortion of the nonlinear streak perturbation reduces the amplification rates of the Mack-mode instability. More importantly, however, the present results demonstrate that the spanwise varying component of the streak can produce a larger effect on the Mack-mode amplification. The study with selected azimuthal wavenumbers for the stationary streaks reveals that a wavenumber of approximately 1.4 times larger than the optimal wavenumber is more effective in stabilizing the planar Mack-mode instabilities. In the absence of unstable first-mode waves for the present cold-wall condition, transition onset is expected to be delayed until the peak streak amplitude increases to nearly 35 percent of the freestream velocity, when intrinsic instabilities of the boundary-layer streaks begin to dominate the transition process. For streak amplitudes below that limit a significant net stabilization is achieved, yielding a potential transition delay that can exceed 100 percent of the length of the laminar region in the uncontrolled case.

Boundary layer stability↗
NASA NTRS1959

Wind-Tunnel Investigation at Subsonic and Supersonic Speeds of the Static and Dynamic Stability Derivatives of an Airplane Model with an Unswept Wing and a High Horizontal Tail

Results are presented of a wind-tunnel investigation to evaluate the static and dynamic stability derivatives of a model with a low-aspect-ratio unswept wing and a high horizontal tail. In addition to results for the complete model, results were also obtained of the body alone, body and wing, and body and tail. Data were obtained in the Mach number range from 0.65 to 2.2, at a Reynolds number of 2 million based on the wing mean aerodynamic chord. The angle-of-attack range for most of the data was -11.5 deg to 18 deg. A limited amount of data was obtained with fixed transition. A correspondence between the damping in pitch and the static stability, previously noted in other investigations, was also observed in the present results. The effect observed was that a decrease (or increase) in the static stability was accompanied by an increase (or decrease) in the damping in pitch. A similar correspondence was observed between the damping in yaw and the static-directional stability. Results from similar tests of the same model configuration in two other facilities over different speed ranges are presented for comparison. It was found that most of the results from the three investigations correlated reasonably well. Estimates of the rotary derivatives were made using available procedures. Comparison with the experimental results indicates the need for development of more precise estimation procedures.

Lessing, Henry C.↗
NASA NTRS1992

Design of a wing shape for study of hypersonic crossflow transition in flight

Computational fluid dynamics methods were used in the design of a wing shape for study of hypersonic crossflow transition in flight. The flight experiment is to be performed on the delta wing of the first stage of a Pegasus launch vehicle as a piggy-back experiment to support boundary-layer stability code development and validation. The design goal is to obtain crossflow-induced transition at 20-40 percent of the chord for a flight Mach number of approximately six. The present paper describes the design and analysis process utilized to obtain desired glove shape. A variety of schemes were used in the design, ranging from simple empirical crossflow correlations to three-dimensional Navier-Stokes codes in conjunction with linear stability/N-factor computations. The sensitivity to various parameters, such as trajectory variations, allowable wing thickness, leading-edge radius and surface temperature, is also discussed.

Godil, A.↗
NASA NTRSDate not supplied

Simplified Vehicle Control Concept for a Lift Plus Cruise eVTOL Vehicle

Electric Vertical Takeoff and Landing (eVTOL) vehicles have the potential to enable cost effective Urban Air Mobility (UAM) applications. These concepts may also pose several challenging handling and control problems, which must be addressed prior to safe and efficient urban operations. This paper investigates a simplified vehicle control concept that is designed to address some of these challenges for a conceptual Lift Plus Cruise vehicle. This concept also includes several variations of a transition-to-hover function, designed to assist pilots in capturing and maintaining a stabilized hover prior to landing. The different simplified control architectures for this concept are presented along with preliminary findings. Preliminary results show that the simplified control concept can be effective in assisting pilots to achieve safe and reliable hover landings, and that transition-to-hover functions have the potential of reducing workload while increasing accuracy. A follow on evaluation will be performed in the Vertical Motion Simulator (VMS) at NASA Ames Research Center. The planned tests will focus on more operationally representative scenarios, while building upon these operations with additional test cases exploring variations in glidepath angles and wind conditions.

simplified vehicle control↗
NASA NTRS1984

Correlations of supersonic boundary-layer transition on cones including effects of large axial variations in wind-tunnel noise

Transition data on sharp tip cones in two pilot low disturbance wind tunnels at Mach numbers of 3.5 and 5 were correlated in terms of noise parameters with data from several conventional wind tunnels and with data from supersonic flight tests on a transition cone. The noise parameters were developed to account for the large axial variations of the free stream noise and the very high frequency noise spectra that occurred in the low disturbance tunnels for some test conditions. The noise could be varied in these tunnels from high levels, approaching those in conventional tunnels, to extremely low levels. The correlations indicated that transition in the low disturbance tunnels was dominated by the local stream noise that was incident on the cone boundary layer unstream of the neutral stability point. The correlation results also suggested that high frequency components of the low disturbance tunnel noise spectra had significant effects on transition when the noise was incident on the boundary layer both upstream and downstream of the neutral stability point.

Chen, F. J.↗
NASA NTRS1980

Mass loss from warm giants: Magnetic effects

Among warm giant stars, rapid mass loss sets in along a well defined velocity dividing line (VDL). Hot corona also disappear close to the VDL and thermal pressure cannot drive the observed rapid mass loss in these stars. The VDL may be associated with magnetic fields changing from closed to open. Such a change is consistent with the lack of X-rays from late-type giants. A magnetic transition locus based on Pneuman's work on helmet streamer stability agrees well with the empirical VDL. The change from closed to open fields not only makes rapid mass loss possible, but also contributes to energizing the mass loss in the form of discrete bubbles.

Mullan, D. J.↗
NASA NTRS1980

Screening of high temperature adhesives for large area bonding

High temperature-resistant adhesive systems were screened for processability, mechanical and physical properties, operational capability at 589 K (600 F), and the ability to produce large area bonds of high quality in fabricating Space Shuttle components. The adhesives consisted primarily of polyimide systems, including FM34B-18, NR-150B2 (DuPont), PMR-15, LARC-13, LARC-160, Thermid 600, and AI-1130L (AMOCA). The processing studies included preparation of polyimide resins, fabrication of film adhesives, development of lay-up and cure procedures, fabrication of honeycomb sandwich panels, and fabrication of mid-plane bonded panels in joints up to 30.5 cm (12 in.) wide. The screening program included tests for tack and drape properties, reticulation and filleting characteristics, ability to produce void-free or low porosity bonds in mid-plane bonded panels, out-time stability, lap shear strength, climbing drum peel strength, and glass transition temperature (Tg). This paper describes the processing methods developed and the test results.

Stenersen, A. A.↗
NASA NTRS1992

The linear stability of a flat plate boundary-layer approaching a cylindrical obstacle

The linear stability of the low-speed three-dimensional flow over a flat plate with an attached cylinder is studied. The region of interest is upstream of the initial separation point and includes the effects of both adverse and favorable pressure gradients, as well as crossflow. The resulting boundary-layer is subject to both the Tollmien-Schlichting (TS) and crossflow instabilities. Linear stability calculations, using N-factor correlations, indicate that the transition process would be dominated by TS instabilities, although for low frequencies crossflow-type disturbances are important.

Spall, R. E.↗
NASA NTRS2000

Homologous recombination as a potential target for caffeine radiosensitization in mammalian cells: reduced caffeine radiosensitization in XRCC2 and XRCC3 mutants

The radiosensitizing effect of caffeine has been associated with the disruption of multiple DNA damage-responsive cell cycle checkpoints, but several lines of evidence also implicate inhibition of DNA repair. The role of DNA repair inhibition in caffeine radiosensitization remains uncharacterized, and it is unknown which repair process, or lesion, is affected. We show that a radiosensitive cell line, mutant for the RAD51 homolog XRCC2 and defective in homologous recombination repair (HRR), displays significantly diminished caffeine radiosensitization that can be restored by expression of XRCC2. Despite the reduced radiosensitization, caffeine effectively abrogates checkpoints in S and G2 phases in XRCC2 mutant cells indicating that checkpoint abrogation is not sufficient for radiosensitization. Another radiosensitive line, mutant for XRCC3 and defective in HRR, similarly shows reduced caffeine radiosensitization. On the other hand, a radiosensitive mutant (irs-20) of DNA-PKcs with a defect in non-homologous end-joining (NHEJ) is radiosensitized by caffeine to an extent comparable to wild-type cells. In addition, rejoining of radiation-induced DNA DSBs, that mainly reflects NHEJ, remains unaffected by caffeine in XRCC2 and XRCC3 mutants, or their wild-type counterparts. These observations suggest that caffeine targets steps in HRR but not in NHEJ and that abrogation of checkpoint response is not sufficient to explain radiosensitization. Indeed, immortalized fibroblasts from AT patients show caffeine radiosensitization despite the checkpoint defects associated with ATM mutation. We propose that caffeine radiosensitization is mediated by inhibition of stages in DNA DSB repair requiring HRR and that checkpoint disruption contributes by allowing these DSBs to transit into irreparable states. Thus, checkpoints may contribute to genomic stability by promoting error-free HRR.

NASA Discipline Radiation Health↗