Search NASA⌕ Search

SEARCH · Search NASA

Results for “Two point model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Shapes and stability of algebraic nuclear models

A generalization of the procedure to study shapes and stability of algebraic nuclear models introduced by Gilmore is presented. One calculates the expectation value of the Hamiltonian with respect to the coherent states of the algebraic structure of the system. Then equilibrium configurations of the resulting energy surface, which depends in general on state variables and a set of parameters, are classified through the Catastrophe theory. For one- and two-body interactions in the Hamiltonian of the interacting Boson model-1, the critical points are organized through the Cusp catastrophe. As an example, we apply this Separatrix to describe the energy surfaces associated to the Rutenium and Samarium isotopes.

Lopez-Moreno, Enrique↗
NASA NTRS2009

Flight Dynamics of an Aeroshell Using an Attached Inflatable Aerodynamic Decelerator

An aeroelastic analysis of the behavior of an entry vehicle utilizing an attached inflatable aerodynamic decelerator during supersonic flight is presented. The analysis consists of a planar, four degree of freedom simulation. The aeroshell and the IAD are assumed to be separate, rigid bodies connected with a spring-damper at an interface point constraining the relative motion of the two bodies. Aerodynamic forces and moments are modeled using modified Newtonian aerodynamics. The analysis includes the contribution of static aerodynamic forces and moments as well as pitch damping. Two cases are considered in the analysis: constant velocity flight and planar free flight. For the constant velocity and free flight cases with neutral pitch damping, configurations with highly-stiff interfaces exhibit statically stable but dynamically unstable aeroshell angle of attack. Moderately stiff interfaces exhibit static and dynamic stability of aeroshell angle of attack due to damping induced by the pitch angle rate lag between the aeroshell and IAD. For the free-flight case, low values of both the interface stiffness and damping cause divergence of the aeroshell angle of attack due to the offset of the IAD drag force with respect to the aeroshell center of mass. The presence of dynamic aerodynamic moments was found to influence the stability characteristics of the vehicle. The effect of gravity on the aeroshell angle of attack stability characteristics was determined to be negligible for the cases investigated.

Cruz, Juan R.↗
NASA NTRS2019

Concept Evaluation: NASA Reference Model 2-Side by Side

Urban Air Mobility (UAM) is an up and coming topic in the world of aerosciences. A variety of companies, most notably Uber, has begun working towards making air taxis a regular part of day to day life. However, the implementation of this system into society will require a significant amount of work: making helicopters that can handle these flights and operate safely in urban environments, having landing zones, and working out new technologies to lower costs. NASA has also taken interest in this new idea and has formed a focus group of interns to tackle some of these problems. They have started by designing a few concept models for what these air taxis could look like, focusing on low noise, multiple passenger configurations, and the potential for electric or hybrid helicopters. One particular model is known as NR2, or the "Side by Side," which features two rotors spinning in opposite directions. Though these models are purely conceptual at this point, understanding the real-world aerodynamics and performance of this model is crucial to its future development. Using a program known as Rotorcraft Computational Fluid Dynamics (RotCFD), the performance characteristics of the rotors and aircraft, such as the lift, drag, thrust and power can be determined. These simulations can be run in a variety of flight configurations, with hover, forward flight, and climb being focused on in this study. The rotor collective angle can also be changed and used to get results about the lift and drag for the blades and the model body. These simulations can provide information for future model construction and wind tunnel testing.

Reference Model↗
NASA NTRS2021

Optial Experiments and Model Validation of Perturbed Starshade Designs

Starshades are a leading technology to enable the direct detection and spectroscopic characterization of Earth- like exoplanets. Critical starshade technologies are currently being advanced through the S5 Project and at the Princeton starshade testbed. We report on the status of Milestone 2 of the S5 Project, optical model validation. We present results from optical experiments of starshades with intentional perturbations built into their design. These perturbations are representative of the type of perturbations possible in a flight design and serve as points of validation for dffraction models and error budgets. We show experimental results for two perturbed shapes, a mask with all petals shifted radially outward by 5 um and a mask with shallow sine waves built into two petals. We compare these data to outputs of the optical model and demonstrate better than 25% agreement. We also present images taken in crossed polarized light and use those data to constrain physical parameters of the optical edge. Bringing in previously obtained results for other perturbed shapes, we show an agreement between experiment and model of better than 25% and argue that this satisfies the Milestone 2 criteria.

Galvin, Michael↗
NASA NTRS2003

Theoretical Analysis of Thermodynamic Measurements near a Liquid-Gas Critical Point

Over the years, many ground-based studies have been performed near liquid-gas critical points to elucidate the expected divergences in thermodynamic quantities. The unambiguous interpretation of these studies very near the critical point is hindered by a gravity-induced density stratification. However, these ground-based measurements can give insight into the crossover behavior between the asymptotic critical region near the transition and the mean field region farther away. We have completed a detailed analysis of heat capacity, susceptibility and coexistence curve measurements near the He-3 liquid-gas critical point using the minimal-subtraction renormalization (MSR) scheme within the phi(exp 4) model. This MSR scheme, using only two adjustable parameters, provides a reasonable global fit to all of these experimental measurements in the gravity-free region out to a reduced temperature of |t| approx. 2x10(exp -2). Recently this approach has also been applied to the earlier microgravity measurements of Haupt and Straub in SF(sub 6) with surprising results. The conclusions drawn from the MSR analyses will be presented. Measurements in the gravity-affected region closer to the He-3 critical point have also been analyzed using the recent crossover parametric model (CPM) of the equation-of-state. The results of fitting heat capacity measurements to the CPM model along the He-3 critical isochore in the gravity-affected region will also be presented.

Barmatz, M.↗
NASA NTRS2018

Overview of the Digitization Workflow Post Image Acquisition of Apollo Lunar and Antarctic Meteorite Samples Using Agisoft Photoscan for the NASA 3D Astromaterials Virtual Samples Collection

The 3D Virtual Astromaterials Samples (3DVAS) collection is a multi-year funded project to create a digital database of sixty Apollo Lunar and Antarctic Meteorite samples following non-destructive documentation conservation protocols. After initial image processing, the photos are evaluated and processed using unique structure-from-motion photogrammetric techniques in a high performance modelling software designed to create a 3D model from 2D images: Agisoft Photoscan Pro. Agisoft Photoscan Pro uses image processing algorithms and techniques originating in computer vision to resolve 3D models for accurate and detailed visualization of a subject. The software provides a stepwise process that is tailored per model based on spatial and specular reflectance properties, for example. The process includes: photo alignment, creation of a dense point cloud, mesh, and finally texture. Photo alignment is dependent on model properties. The 3DVAS process requires a special rotation platform with calibrated photogrammetric targets, specific distance rotation protocols, and a contrasting background for alignment and scale accuracy. As a result of the photographic process, alignment will complete with two mirrored hemispheres that, in a sense, represent the 2D images overlapping to create a 3D model. Each dense point cloud is analyzed with provided statistical measures in a gradual selection process to eliminate outliers. The point cloud is reduced to include only data valuable to the final model. When a precise dense point cloud is achieved, a mesh and texture are applied. Each model is scaled with scale bar accuracies within 100 microns. Each sample has its own intimate process for modelling; there is no standard for the parameters required in the final creation of a high resolution model. By processing multiple samples, a skill is gained in practice to allow a close definition of the original sample and will result in the most detailed version of the sample shell. This process completes one-fifth of the 3DVAS protocol for providing accurate digital documentation. Each model shell is merged with X-ray Computed Tomography data to create a full volumetric sample. All 3DVAS data will be served on NASA's Astromaterials Acquisition and Curation website with an early subset of data available in 2019 and the 3D Virtual Astromaterials Samples Collection launch in 2020.

Thomas, Andi B.↗
NASA NTRS1977

A color prediction model for imagery analysis

A simple model has been devised to selectively construct several points within a scene using multispectral imagery. The model correlates black-and-white density values to color components of diazo film so as to maximize the color contrast of two or three points per composite. The CIE (Commission Internationale de l'Eclairage) color coordinate system is used as a quantitative reference to locate these points in color space. Superimposed on this quantitative reference is a perceptional framework which functionally contrasts color values in a psychophysical sense. This methodology permits a more quantitative approach to the manual interpretation of multispectral imagery while resulting in improved accuracy and lower costs.

Skaley, J. E.↗
DOE OSTI2022

Photometric redshift estimation with convolutional neural networks and galaxy images: Case study of resolving biases in data-driven methods

Deep-learning models have been increasingly exploited in astrophysical studies, but these data-driven algorithms are prone to producing biased outputs that are detrimental for subsequent analyses. In this work, we investigate two main forms of biases: class-dependent residuals, and mode collapse. We do this in a case study, in which we estimate photometric redshift as a classification problem using convolutional neural networks (CNNs) trained with galaxy images and associated spectroscopic redshifts. We focus on point estimates and propose a set of consecutive steps for resolving the two biases based on CNN models, involving representation learning with multichannel outputs, balancing the training data, and leveraging soft labels. The residuals can be viewed as a function of spectroscopic redshift or photometric redshift, and the biases with respect to these two definitions are incompatible and should be treated individually. We suggest that a prerequisite for resolving biases in photometric space is resolving biases in spectroscopic space. Experiments show that our methods can better control biases than benchmark methods, and they are robust in various implementing and training conditions with high-quality data. Our methods hold promises for future cosmological surveys that require a good constraint of biases, and they may be applied to regression problems and other studies that make use of data-driven models. Nonetheless, the bias-variance tradeoff and the requirement of sufficient statistics suggest that we need better methods and optimized data usage strategies.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS2001

Flight Test Identification and Simulation of a UH-60A Helicopter and Slung Load

Helicopter slung-load operations are common in both military and civil contexts. Helicopters and loads are often qualified for these operations by means of flight tests, which can be expensive and time consuming. There is significant potential to reduce such costs both through revisions in flight-test methods and by using validated simulation models. To these ends, flight tests were conducted at Moffett Field to demonstrate the identification of key dynamic parameters during flight tests (aircraft stability margins and handling-qualities parameters, and load pendulum stability), and to accumulate a data base for simulation development and validation. The test aircraft was a UH-60A Black Hawk, and the primary test load was an instrumented 8- by 6- by 6-ft cargo container. Tests were focused on the lateral and longitudinal axes, which are the axes most affected by the load pendulum modes in the frequency range of interest for handling qualities; tests were conducted at airspeeds from hover to 80 knots. Using telemetered data, the dynamic parameters were evaluated in near real time after each test airspeed and before clearing the aircraft to the next test point. These computations were completed in under 1 min. A simulation model was implemented by integrating an advanced model of the UH-60A aerodynamics, dynamic equations for the two-body slung-load system, and load static aerodynamics obtained from wind-tunnel measurements. Comparisons with flight data for the helicopter alone and with a slung load showed good overall agreement for all parameters and test points; however, unmodeled secondary dynamic losses around 2 Hz were found in the helicopter model and they resulted in conservative stability margin estimates.

Cicolani, Luigi S.↗
NASA NTRS1997

Coherent Effects in Microwave Backscattering Models for Forrest Canopies

In modeling forest canopies, several scattering mechanisms are taken into account: (1) volume scattering; (2) surface-volume interaction; and (3) surface scattering from forest floor. Depending on the structural and dielectric characteristics of forest canopies, the relative contribution of each mechanism in the total backscatter signal of an imaging radar can vary. In this paper, two commonly used first-order discrete scattering models, distorted born approximation (DBA) and radiative transfer (RT) are used to simulate the backscattered power received by polarimetric radars at P-, L-, and C-bands over coniferous and deciduous forests. The difference between the two models resides on the coherent effect in the surface-volume interaction terms. To demonstrate this point, the models are first compared based on their underlying theoretical assumptions and then according to simulation results over coniferous and deciduous forests. It is shown that by using the same scattering functions for various components of trees (i.e., leaf, branch, stem), the radiative transfer and distorted Born models are equivalent, except in low frequencies, where surface-volume interaction terms may become important, and the coherent contribution may be significant. In this case, the difference between the two models can reach up to 3 dB in both co-polarized and cross-polarized channels, which can influence the performance of retrieval algorithms.

Saatchi, Sasan S.↗
DOE OSTI2022

A new dynamic zOnal model with air-diffuser (DOMA) - Application to thermal comfort prediction

A new Dynamic zOnal Model with Air-diffuser (DOMA) was developed. Several case studies were investigated and tested to evaluate and validate this program using measurement data. This new model was integrated into a TRaNsient SYstems Simulation program library and coupled with the multi-zone thermal model. The DOMA/TRNSYS coupled model was then used to predict room temperature distribution over an entire day of a single-zone building. The results show that increasing the heating outputs of the electric floor system, for example, from 75 to 200 W/m 2 , would not effectively improve the indoor thermal comfort, since the thermostat will reach the set point first and then turn off the system before the room gets enough heat and reach a comfortable level. This indicates the importance of selecting an appropriate location and set point for the thermostat when using a floor heating system. This potential thermal comfort issue can only be identified through the two-node model with a dynamic zonal model rather than the conventional PMV model, which thus suggests that for optimizing indoor thermal comfort of a building equipped with a time-sensitive control strategy and/or HVAC system, the TSENS results obtained from the two-node model integrated with DOMA are more appropriate than PMVs.

Construction & Building Technology↗
DOE OSTI2020

Measurements of proton capture in the A=100–110 mass region: Constraints on the In 111 (γ,p)/(γ,n) branching point relevant to the γ process

The γ process is an explosive astrophysical scenario, which is thought to be the primary source of the rare proton-rich stable p nuclei. However, current γ-process models remain insufficient in describing the observed p-nuclei abundances, with disagreements up to two orders of magnitude. A sensitivity study has identified 111 In as a model-sensitive (γ,p)/(γ,n) branching point within the γ process. Constraining the involved reaction rates may have a significant impact on the predicted p-nuclei abundances. Here we report on measurements of the cross sections for 102 Pd (p,γ) 103 Ag, 108 Cd (p,γ) 109 In, and 110 Cd (p,γ) 111 In reactions for proton laboratory energies 3–8 MeV using the high efficiency total absorption spectrometer and the γ-summing technique. These measurements were used to constrain Hauser-Feshbach parameters used in talys 1.9, which constrains the 111 In(γ,p) 110 Cd and 111 In(γ,n) 110 Ag reaction rates. The newly constrained reaction rates indicate that the 111 In(γ,p)/(γ,n) branching point occurs at a temperature of 2.71 ± 0.05 GK, well within the temperature range relevant to the γ process. These findings differ significantly from previous studies and may impact the calculated abundances.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Principles and Options for Designing Battery Energy Storage Zoning Ordinances

Deployment of battery energy storage (BESS) systems, both standalone and as part of hybrid systems paired with generation, has rapidly increased in the United States in recent years as utilities and communities have deployed storage to improve electric grid reliability and act as a cost-effective alternative to larger grid infrastructure. The modular nature of BESS technologies means systems may be built near other existing land uses, creating the potential for conflicts with neighboring landowners that can be managed and mitigated through zoning and permitting requirements established by local jurisdictions. While many cities and counties have adopted ordinances specific to BESS into their local zoning codes, these ordinances vary significantly in their requirements and level of detail. Meanwhile, many other jurisdictions, including those home to proposed or existing BESS projects, lack any specific language related to BESS in their zoning codes. Local planning and zoning officials have limited capacity and may lack the familiarity with BESS technologies needed to develop ordinances or otherwise make reasonable zoning decisions that balance safety, community impacts, and other goals. The resulting uncertainty at the local zoning level has led developers to withdraw projects in some areas and has spurred moratoria or bans on energy storage projects in others. This report intends to provide practical resources for practitioners interested in reasonable and effective local regulation of battery energy storage. It does not present a model zoning ordinance, but rather is intended to complement model ordinances developed by others by providing additional context and analysis regarding the structure of energy storage zoning ordinances and the decision points for local officials. Zoning ordinances at the city, town, and county level across the U.S. were surveyed alongside two template model ordinances to identify common elements and options for regulating the zoning and siting of BESS. Common elements identified and analyzed include definitions and general requirements, including cutoffs or tiers used to apply regulations to different system sizes and the permitted zones where jurisdictions allow BESS to be sited; visual, noise, and aesthetic requirements, including property line setbacks, fencing and visual screening, noise, and lighting requirements; and safety and planning requirements, such as site plans, decommissioning plans or funds, and requirements for access by emergency services. The report also summarizes some of the more unique regulations, including those that place additional restrictions on BESS at the local level.

25 ENERGY STORAGE↗
DOE OSTI2020

Time Evolution of Correlation Functions in Quantum Many-Body Systems

We give rigorous analytical results on the temporal behavior of two-point correlation functions—also known as dynamical response functions or Green’s functions—in closed many-body quantum systems. We show that in a large class of translation-invariant models the correlation functions factorize at late times $\langle$A ( t ) B$\rangle$ β → $\langle$ A$\rangle$ β $\langle$ B$\rangle$ β , thus proving that dissipation emerges out of the unitary dynamics of the system. We also show that for systems with a generic spectrum the fluctuations around this late-time value are bounded by the purity of the thermal ensemble, which generally decays exponentially with system size. For autocorrelation functions we provide an upper bound on the timescale at which they reach the factorized late time value. Remarkably, this bound is only a function of local expectation values and does not increase with system size. We give numerical examples that show that this bound is a good estimate in nonintegrable models, and argue that the timescale that appears can be understood in terms of an emergent fluctuation-dissipation theorem. Our study extends to further classes of two point functions such as the symmetrized ones and the Kubo function that appears in linear response theory, for which we give analogous results.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2018

Sigma Models with Complex, Graded and η-Deformed Target Spaces

I describe a class of two-dimensional σ-models with complex homogeneous target spaces, whose equations of motion admit zero-curvature representations. I point out the relation to models with Z{sub m} -graded target spaces and to the so-called η-deformed models.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1980

The contribution of the diffuse light component to the topographic effect on remotely sensed data

The topographic effect is measured by the difference between the global radiance from inclined surfaces as a function of their orientation relative to the sensor position and light source. The short wave radiant energy incident on a surface is composed of direct sunlight, scattered skylight, and light reflected from surrounding terrain. The latter two components are commonly known as the diffuse component. The contribution of the diffuse light component to the topographic effect was examined and the significance of this diffuse component with respect to two direct radiance models was assessed. Diffuse and global spectral radiances were measured for a series of slopes and aspects of a uniform and surface in the red and photographic infrared parts of the spectrum, using a nadir pointing two channel handheld radiometer. The diffuse light was found to produce a topographic effect which varied from the topographic effect for direct light. The topographic effect caused by diffuse light was found to increase slightly with solar elevation and wavelength for the channels examined. The correlations between data derived from two simple direct radiance simulation models and the field data were not significantly affected when the diffuse component was removed from the radiances. Radiances from a 60 percent reflective surface, assuming no atmospheric path radiance, the diffuse light topographic effect contributed a maximum range of 3 pixel values in simulated LANDSAT data from all aspects with slopes up to 30 degrees.

Justice, C.↗
NASA NTRS1975

The slow recirculating flow near the rear stagnation point of a wake

A model is suggested in which some of the important features of the circulating flow inside the two-dimensional near wake are derived by assuming a slow viscous flow. The theory considers the flow away from the body base. It is found that there is a region of constant speed merging, as we go downstream, into a region of stagnation-apex flow. The velocity returning from the rear stagnation point along the center streamline is shown to be a slowly varying function of the 'wedge-angle,' of the wake and to be roughly one half the velocity at the edge of the shear layers driving the wake-cavity flow. These results seem to be in agreement with experimental data.

Abarbanel, S.↗
DOE OSTI2022

A correction procedure for self-induced velocity of a finite-sized particle in two-way coupled Euler–Lagrange simulations

The importance of incorporating a correction to undo the self-induced perturbation velocity of a particle, when its size becomes comparable to the Eulerian grid, in a two-way coupled Euler–Lagrange (EL) simulation is now well appreciated. The present work improves upon the prior correction procedures in a few important ways. First, the past correction procedures have been scalar-based with the assumption that the quasi-steady force is the source of self-induced velocity perturbation. Here we generalize to a vector correction procedure and thereby the directions of feedback force and relative velocity can be different. This allows the correction procedure to be used even in the presence of added-mass, history, and lift forces. Second, the effect of a nearby wall has been systematically included in the correction procedure. The correction procedure depends on fundamental Oseen solutions of streamwise and transverse regularized feedback forces. We present a Fourier transform-based analytical approach to obtaining these regularized Oseen solutions. We also present a step-by-step numerical procedure for obtaining the Oseen solutions in any EL code. With the analytical or numerical Oseen functions, the correction procedure can be easily implemented in any EL code. Iterations are required in solving the implicit correction equations and it is demonstrated that the correction procedure converges rapidly within three or four iterations. In conclusion, a simple empirical approach is also presented to account for unsteady effects in the correction procedure.

97 MATHEMATICS AND COMPUTING↗