SEARCH · Search NASA
Results for “USER FACILITY”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Influence of copper on nickel-based catalysts in the conversion of glycerol
Not Available
Sub-micron Cu/SSZ-13: Synthesis and application as selective catalytic reduction (SCR) catalysts
Not Available
Detecting Fermi-level shifts by Auger electron spectroscopy in Si and GaAs
In this paper, changes in surface Fermi-level of Si and GaAs, caused by doping and cleaning, are investigated by Auger electron spectroscopy. Based on the Auger voltage contrast, we compared the Auger transition peak energy but with higher accuracy by using a more accurate detector and an improved peak position determination method. For silicon, a peak shift as large as 0.46 eV was detected when comparing a cleaned p-type and n-type wafer, which corresponds rather well with the theoretical difference in Fermi-level. If no cleaning was applied, the peak position did not differ significantly for both wafer types, indicating Fermi-level pinning in the band gap. For GaAs, peak shifts were detected after cleaning with HF and (NH4)2S-solutions in an inert atmosphere (N2-gas). Although the (NH4)2S-cleaning in N2 is very efficient in removing the oxygen from the surface, the observed Ga- and As-peak shifts are smaller than those obtained after the HF-cleaning. It is shown that the magnitude of the shift is related to the surface composition. After Si-deposition on the (NH4)2S-cleaned surface, the Fermi-level shifts back to a similar position as observed for an as-received wafer, indicating that this combination is not successful in unpinning the Fermi-level of GaAs. This work has been funded by J.D.'s PhD fellowship of the Fund of Scientific Research-Flanders (FWO-V) (Dossier No. 11U4516N). P.H. acknowledges support from Becas Chile-CONICYT. This research was also supported by the FWO Odysseus Program, the Belgian Hercules Stichting with the Project No. Her/08/25 and AKUL/13/19 and the KU Leuven project GOA "Fundamental challenges in Semiconductor Research". The authors would also like to thank Bastiaan Opperdoes and Ludwig Henderix for technical support. The work was supported by the U.S. Department of Energy (USDOE), Office of Science, Office of Basic Energy Sciences, Division of Materials Sciences and Engineering, and performed in the Environmental Molecular Sciences Laboratory, a national scientific user facility sponsored by the Department of Energy's Office of Biological and Environmental Research and located at Pacific Northwest National Laboratory (PNNL). Battelle operates PNNL for the USDOE under contract DE-AC05-76RL01830.
Molecular Dynamics Study of the Proposed Proton Transport Pathways in [FeFe]-Hydrogenase
Possible proton channels in Clostridium pasteurianum [FeFe]-hydrogenase were investigated with molecular dynamics simulations. This study was undertaken to discern proposed channels, compare their properties, evaluate the functional channel, and to provide insight into the features of an active proton channel. Our simulations suggest that protons are not transported through water wires. Instead, a five-residue motif (E282, S319, E279, HOH, C299) was found to be the likely channel, consistent with experimental observations. This channel connects the surface of the enzyme and the di-thiomethylamine bridge of the catalytic H-cluster, permitting the transport of protons. The channel was found to have a persistent hydrogen bonded core (residues E279 to S319), with less persistent hydrogen bonds at the ends of the channel. The hydrogen bond occupancy in this network was found to be sensitive to the protonation state of the residues in the channel, with different protonation states enhancing or stabilizing hydrogen bonding in different regions of the network. Single site mutations to non-hydrogen bonding residues break the hydrogen bonding network at that residue, consistent with experimental observations showing catalyst inactivation. In many cases, these mutations alter the hydrogen bonding in other regions of the channel which may be equally important in catalytic failure. A correlation between the protein dynamics near the proton channel and the redox partner binding regions was also found as a function of protonation state. The likely mechanism of proton movement in [FeFe]-hydrogenases is discussed based on the structural analysis presented here. This work was funded by the DOE Office of Science Early Career Research Program through the Office of Basic Energy Sciences. Computational resources were provided at W. R. Wiley Environmental Molecular Science Laboratory (EMSL), a national scientific user facility sponsored by the Department of Energy’s Office of Biological and Environmental Research located at Pacific Northwest National Laboratory, and a portion of the research was performed using PNNL Institutional Computing at Pacific Northwest National Laboratory. Pacific Northwest National Laboratory is operated by Battelle for the U.S. Department of Energy.
Predicting the evolution of biomass bulk density through feedstock preprocessing: Discrete element modeling, regression analysis, and pilot-scale validation
Bulk density is an important material property of biomass feedstocks, influencing handling, storage, transport costs, and conversion efficiency. In this study, predictive regression models for loose and tapped bulk densities of Alamo and Cave-in-Rock switchgrass are developed using a comprehensive dataset generated via calibrated bonded-sphere discrete element method (DEM) simulations. Here, a key contribution of this study is the use of a DEM-based approach, which correlates density with moisture content and particle size distribution parameters and enables analysis across a continuous particle size range, overcoming limitations of purely experimental data. For comparison, regression models are also developed using only experimental data from pilot-scale runs at the Biomass Feedstock National User Facility at Idaho National Laboratory. Validation against pilot-scale data showed reasonable prediction accuracy for both model types, particularly for smaller particle sizes (post-secondary grinding). While the experimental model showed slightly better performance matching the validation data in some cases, the DEM-based model benefits from a much larger dataset, reduced predictor multicollinearity, and continuous parameter coverage, highlighting the utility of validated simulation models for developing robust predictive tools for biomass preprocessing applications.
Neutron irradiation induced microstructural changes in NBG-18 and IG-110 nuclear graphites
Not Available
Properties of immobile hydrogen confined in microporous carbon
The mobility of H2 confined in microporous carbon was studied as a function of temperature and pressure using inelastic neutron scattering, and the translational and rotational motion of H2 molecules has been probed. At low loading, rotation of H2 molecules adsorbed in the smallest carbon pores (~6 ) is severely hindered, suggesting that the interaction between H2 and the host matrix is anisotropic. At higher loading, H2 molecules behave as nearly free rotor, implying lower anisotropic interactions with adsorption sites. At supercritical temperatures where bulk H2 is a gas, the inelastic spectrum of confined H2 provides evidence of a significant fraction of immobile, solid-like hydrogen. The onset temperature for molecular mobility depends strongly on the loaded amount. The fraction of immobile molecules increases with pressure and attains a plateau at high pressures. Surprisingly, immobile H2 is present even at temperatures as high as ~110 K. This research at ORNL s Spallation Neutron Source was sponsored by the Scientific User Facilities Division, Office of Basic Energy Sciences, U. S. Department of Energy. This research was supported in part by the ORNL Postdoctoral Research Associates Program, administered jointly by the ORNL and the Oak Ridge Institute for Science and Education. CIC and NCG acknowledge support from the Materials Science and Engineering Division, Office of Basic Energy Sciences, U.S. Department of Energy.
Effects of Potassium Doping on CO Hydrogenation Over MoS2 Catalysts: A First-Principles Investigation
Periodic density functional theory calculations were performed to explore the effects of doping potassium (K) on the reactivity of CO hydrogenation to mixed higher alcohols over MoS2 catalysts. We found that the doped K species over the model MoS2(100) catalyst surface acts as a unique site for CO adsorption where either the K-C or the K-O bonding is allowed. The charge transfer from the K 4s electron to the conduction band of the MoS2(100) surface slightly enhances CO adsorption at the edge Mo sites. Due to the large electropositive nature, the presence of the surface K species, however, will hinder the dissociative adsorption of hydrogen. As a result, the doping K species drive CO hydrogenation selectivity toward the C2+ alcohols instead of hydrocarbons by increasing CO and decreasing hydrogen coverages on the MoS2 catalysts. To further elucidate the effect of doping K on the shifting of the selectivity toward CO hydrogenation, we calculated several key reaction steps leading to the H2CCO precursor formation, i.e., CO hydrogenation, the C-O bond scission and the C-C coupling (CH2+CO). The C-C coupling step is favorable for both the Mo and S edges. However, the undoped S edge has an overall more thermodynamically favorable reaction profile up to C-O scission compared with the Mo edge. This work was funded by a CRADA project (No. PNNL/297) with Range Fuels. The research was performed using EMSL, a national scientific user facility sponsored by the Department of Energy's Office of Biological and Environmental Research and located at Pacific Northwest National Laboratory. The work involving the results analysis and mansucript writing was supported by the US Department of Energy, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences & Biosciences.
NO oxidation on zeolite supported Cu catalysts: Formation and reactivity of surface nitrates
Not Available
NH3-SCR on Cu, Fe and Cu+Fe exchanged Beta and SSZ-13 catalysts: hydrothermal aging and propylene poisoning effects
Cu, Fe and Cu+Fe ion exchanged Beta and SSZ-13 catalysts were prepared by solution ion exchange using commercial NH4/Beta, and NH4/SSZ-13 that was prepared in-house. To study hydrothermal aging effects, Beta supported catalysts were aged hydrothermally at 700 C and SSZ-13 supported catalysts were aged at 750 C. In order to reveal the effects of Fe addition in the co-exchanged catalysts, these catalysts were characterized by means of powder X-ray diffraction (XRD), N2 adsorption-desorption, electron paramagnetic resonance (EPR), 27Al-nuclear magnetic resonance (27Al-NMR) and propylene coking followed with temperature programmed reaction (TPR), and further tested with standard NH3-SCR with and without the presence of propylene. Collectively, the catalyst characterizations and reaction testing indicated minor beneficial effects of Fe addition in Cu,Fe/Beta, where NH3-SCR activity, N2 selectivity and hydrothermal stability were all slightly improved. In contrast, Fe addition did not show apparent beneficial effects in low-temperature SCR for the Cu,Fe/SSZ-13 case. At elevated reaction temperatures, however, the presence of Fe indeed considerably improved NO conversion and N2 selectivity for the hydrothermally aged Cu,Fe/SSZ-13 catalyst in the presence of propylene. The authors from Pacific Northwest National Laboratory (PNNL) gratefully acknowledge the US Department of Energy (DOE), Energy Efficiency and Renewable Energy, Vehicle Technologies Office for the support of this work. The research described in this paper was performed in the Environmental Molecular Sciences Laboratory (EMSL), a national scientific user facility sponsored by the DOE’s Office of Biological and Environmental Research and located at PNNL. PNNL is operated for the US DOE by Battelle. The authors from East China University of Science and Technology acknowledge support from National Basic Research Program of China (2013CB933200), National Natural Science Foundation of China (21577035, 21577034), Commission of Science and Technology of Shanghai Municipality (15DZ1205305) and 111 Project (B08021). Aiyong Wang also gratefully acknowledges the China Scholarship Council for a Joint-Training Scholarship Program with PNNL.
A Theoretical Study on Reaction Mechanisms and Kinetics of Thiophene Hydrodesulfurization over MoS 2 Catalysts
In the present work, thiophene hydrodesulphurization (HDS) over the Mo-edge, the S-edge, and the Mo-S connection edge of MoS 2 catalyst with 50% sulfur coverage was studied using first-principles based microkinetic modeling. Two parallel HDS routes, i.e., direct desulfurization (DDS) and hydrogenation (HYD) were taken into account. It has been found that the major reaction route of thiophene HDS on the Mo- and the Mo-S edges is temperature dependent. In the low temperature range of 500~600 K, the HYD route is dominant, leading to the C 4 H 8 formation. As the temperature increases, the DDS route becomes competitive with the HYD route. At the temperature above 650 K, the DDS route will be the dominant HDS reaction route on the Mo- and the Mo-S edges. While the DDS route that leads to the formation of C4H6 is the major thiophene HDS reaction route on the S-edge in the entire temperature range of 500~750 K. The microkinetic modeling results show the overall HDS activity on the S-edge is lower than it on the Mo- and the Mo-S edges. The Mo-S edge also provides a preferential reaction pathway, which facilitates 2-hydrothiophene migration from the Mo-edge to the S-edge, followed by remaining elementary steps with lower activation barriers in the DDS route. The work was financially supported by the National Natural Science Foundation of China (No. 21476012, 21571012, 21407007 and 91534201). The computing time was granted by a scientific theme user proposal in the William R. Wiley Environmental Molecular Sciences Laboratory (EMSL), which is a U.S. Department of Energy national scientific user facility located at Pacific Northwest National Laboratory (PNNL) in Richland, Washington. Part of computing time was provided the National Energy Research Scientific Computing Center (NERSC). D. Mei is supported by the US Department of Energy, Office of Sciences, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences & Biosciences.
Exploring the role of pendant amines in transition metal complexes for the reduction of N2 to hydrazine and ammonia
Not Available
Ions interacting in solution: Moving from intrinsic to collective properties
Not Available
Mechanisms of selective cleavage of C–O bonds in di-aryl ethers in aqueous phase
A novel route for cleaving the C-O aryl ether bonds of p-substituted H-, CH 3 -, and OH- diphenyl ethers has been explored over Ni/SiO 2 catalysts at very mild conditions. The C-O bond of diphenyl ether is cleaved by parallel hydrogenolysis and hydrolysis (hydrogenolysis combined with HO* addition) on Ni. The rates as a function of H 2 pressure from 0 to 10 MPa indicate that the rate-determining step is the C-O bond cleavage on Ni. H* atoms compete with the organic reactant for adsorption leading to a maximum in the rate with increasing H 2 pressure. In contrast to diphenyl ether, hydrogenolysis is the exclusive route for cleaving an ether C-O bond of di-p-tolyl ether to form p-cresol and toluene. 4,4'-dihydroxydiphenyl ether undergoes sequential surface hydrogenolysis, first to phenol and HOC 6 H 4 O* (adsorbed), which is then cleaved to phenol (C 6 H 5 O* with added H*) and H 2 O (O* with two added H*) in a second step. Density function theory supports the operation of this pathway. Notably, addition of H* to HOC 6 H 4 O* is less favorable than a further hydrogenolytic C-O bond cleavage. The TOFs of three aryl ethers with Ni/SiO 2 in water followed the order 4,4'-dihydroxydiphenyl ether (69 h -1 ) > diphenyl ether (26 h -1 ) > di-p-tolyl ether (1.3 h -1 ), in line with the increasing apparent activation energies, ranging from 93 kJ∙mol -1 (4,4'-dihydroxydiphenyl ether) < diphenyl ether (98 kJ∙mol -1 ) to di-p-tolyl ether (105 kJ∙mol -1 ). D.M. thanks the support from the US Department of Energy, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences & Biosciences. Pacific Northwest National Laboratory (PNNL) is a multiprogram national laboratory operated for DOE by Battelle. Computing time was granted by the grand challenge of computational catalysis of the William R. Wiley Environmental Molecular Sciences Laboratory (EMSL) and by the National Energy Research Scientific Computing Center (NERSC). EMSL is a national scientific user facility located at Pacific Northwest National Laboratory (PNNL) and sponsored by DOE’s Office of Biological and Environmental Research.