Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS - ASPECT RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

The quiet short-haul research aircraft

The design concepts, performance capabilities, and projected applications of the Quiet Short-Haul Research Aircraft (QSRA) are discussed. The propulsive lift system of the QSRA provides the lift required for short field operations at low community noise levels. This system consists of four high bipass ratio, geared turbofan engines mounted so that the engine exhaust flows across the upper surface of the wing (upper surface blowing). Large specially shaped flaps behind each engine control the direction of the flow for each phase of flight. A 95 passenger short haul transport based on this technology could operate out of a 2500 foot runway with a combined takeoff and landing 90 EPNdB footprint area of 2.7 sq mi.

Cochrane, J. A.↗
NASA NTRS1989

The recombination epoch revisited

Previous studies of cosmological recombination have shown that this process produces as a by-product a highly superthermal population of Ly-alpha photons which retard completion of recombination. Cosmological redshifting was thought to determine the frequency distribution of the photons, while two-photon decay of hydrogen's 2s state was thought to control their numbers. It is shown here that frequency diffusion due to photon scattering dominate the cosmological redshift in the frequency range near line center which fixes the ratio of ground state to excited state population, while incoherent scattering into the far-red damping wing effectively destroys Ly-alpha photons as a rate which is competitive with two-photon decay. The former effect tends to hold back recombination, while the latter tends to accelerate it; the net results depends on cosmological parameters, particularly the combination Omega(b) h/sq rt (2q0), where Omega(b) is the fraction of the critical density provided by baryons.

Krolik, Julian H.↗
NASA NTRS1953

Aerodynamic Characteristics of a Refined Deep-Step Planing-Tail Flying-Boat Hull with Various Forebody and Afterbody Shapes

An investigation was made in the Langley 300 mph 7-by 10-foot tunnel to determine the aerodynamic characteristics of a refined deep-step planing-tail hull with various forebody and afterbody shapes. For comparison, tests were made on a streamline body simulating the fuselage of a modern transport airplane. The results of the tests, which include the interference effects of a 21-percent-thick support wing, indicated that for corresponding configurations the hull models incorporating a forebody with a length-beam ratio of 7 had lower minimum drag coefficients than the hull models incorporating a forebody with a length-beam ratio of 5. Longitudinal and lateral stability was generally about the same for all hull models tested and about the same as that of a conventional hull.

Riebe, John M↗
NASA NTRS1993

High Reynolds Number Configuration Development of a High-Lift Airfoil

An experimental program has been conducted to assess performance of a transport multielement airfoil at flight Reynolds numbers. The studies were performed at chord Reynolds numbers as high as 16 million in the NASA Langley Low Turbulence Pressure Tunnel. Sidewall boundary-layer control to enforce flow two dimensionality was provided via an endplate suction system. The basic airfoil was an 11.55 percent thick supercritical airfoil representative of the stall critical station of a new-generation transport aircraft wing. The multielement airfoil was configured as a three-element airfoil with slat and flap chord ratios of 14.48 percent and 30 percent respectively. Testing focused on the development of landing configurations with high maximum lift capability and the assessment of Reynolds and Mach number effects. Also assessed were high-lift performance effects due to devices such as drooped spoilers and trailing-edge wedges. The present experimental studies revealed significant effects on high-lift airfoil performance due to Reynolds and Mach number variations and favorable lift increments at approach angles of attack due to the use of drooped spoilers or trailing-edge wedges. However, no substantial improvements in maximum lift capability were identified. A recently developed high performance single-segment flap was also tested and results indicated considerable improvements in lift and drag performance over existing airfoils. Additionally, it was found that this new flap shape at its optimum rigging was less sensitive to Reynolds number variations than previous designs.

Walter O Valarezo↗
NASA NTRS1984

Noise and performance characteristics of a model scale X-wing rotor system in hover

Noise data for the hover condition were measured for a 8 m diameter X-wing model rotor mounted on an outdoor whirl tower. The noise was found to be a function of operating condition, in general increasing with performance. The X-wing spectra obtained from narrowband and 1/3-octave band analyses were dominated by the blade passage frequency harmonics. The circulation control slot blowing produced 1 to 10 kHz broadband noise which exhibited a jet velocity to the 5.4 dependency. Under the rotor plane loading noise was dominant, except at low values of blade pressure ratio where a sharp decrease in the blade passage frequency harmonic levels was observed. In the rotor plane, the contribution of the broadband noise sources was greater than under the rotor plane. The X-wing rotor system in hover exhibited flexibility in operating conditions to achieve a specific level of performance. The high collective, low blade passage ratio combinations which meet a given level of performance were associated with low overall sound pressure levels.

Willshire, W. L., Jr.↗
NASA NTRS1990

Aeroservoelastic tailoring for lateral control enhancement

The application of an automated optimization approach to the integrated structural and control design of an aircraft wing and its control surface is illustrated. The performance index or cost function for optimization is the aileron hinge moment required to sustain a specified terminal roll rate at a chosen design speed at which aeroelastic effects are significant. The design variables used for aileron hinge-moment minimization are the aileron flap-to-chord ratio; the location of the aileron with respect to the roll axis; and the orientations of three advanced composite plies comprising 60 percent of the wing structure. The effects of aileron location and advanced composite ply orientation on the terminal roll rate and aileron hinge moment are examined. Optimization is seen to involve a compromise between a laminated structure/aileron combination that is effective in creating large rolling moments and one that minimizes the damping-in-roll. These two requirements are in conflict; the optimization driver must locate a compromise design point by moving the control surface and changing its size while also creating a suitable structural design.

Weisshaar, Terrence A.↗
NASA NTRS1979

Experimental study of acoustic loads on an upper-surface-blown STOL airplane configuration

Fluctuating pressure levels were measured on the flap and fuselage of an upper-surface-blown jet-flap airplane configuration in a wind tunnel. The model tested had turbofan engines with a bypass ratio of 3 and a thrust rating of 10 kN. Rectangular nozzles were mounted flush with the upper surface at 35 percent of the wing chord. Test parameters were flap deflection angle, jet impingement angle, angle of attack, free-stream velocity, spanwise location of the engine, and jet dynamic pressure. Load levels were high throughout the jet impingement region, with the highest levels (about 159 dB) occurring on the fuselage and near the knee of the flap. The magnitude of the forward-velocity effect appeared to depend upon the ratio of free-stream and jet velocities. Good agreement was obtained between fluctuating pressure spectra measured at jet dynamic pressures of 7 and 22 kPa when the spectra were scaled by nondimensional functions of dynamic pressure, velocity, and the empirical relationship between dynamic pressure and overall fluctuating pressure level.

Willis, C. M.↗
NASA NTRS1963

Investigation of Propeller-power-plant Autoprecession Boundaries for a Dynamic-aeroelastic Model of a Four-engine Turboprop Transport Airplane

A flexibly mounted aircraft engine may under certain conditions experience a self-excited whirling instability involving a coupling between the gyroscopic and aerodynamic forces acting on the propeller, and the inertial, elastic, and damping forces contributed by the power plant, nacelle, and wing. This phenomenon has been called autoprecession, or whirl instability. An experimental investigation was made in the Langley transonic dynamics tunnel at Mach numbers below 0.3 to study some of the pertinent parameters influencing the phenomenon. These parameters included propeller rotational speed, stiffness of the power-plant assembly in the pitch and yaw planes and the ratio of pitch stiffness to yaw stiffness, structural damping of the power-plant assembly in the pitch and yaw planes, simulated fuel load in the wings, and the location and number of autoprecessing powerplant assemblies. A large dynamic-aeroelastic model of a four-engine turboprop transport airplane mounted on a vertical rod in a manner which provided several limited body degrees of freedom was used in the investigation. It was found that the boundary for autoprecession decreased markedly with Increasing proreduction of power-plant stiffness and/or damping, and to a lesser degree decreased with reduction of simulated fuel load in the wings. peller rotational speed generally lowered the autoprecession boundary. This effect was more pronounced as the stiffness was increased. An inboard power plant was found to be more susceptible to autoprecession than an outboard one. Combinations in which two or more power plants had the same level of reduced stiffness resulted in autoprecession boundaries considerably lower than that of a single power plant with the same level of reduced stiffness.

POWER PLANT↗
NASA NTRS1976

Wind tunnel investigation of Nacelle-Airframe interference at Mach numbers of 0.9 to 1.4-force data

Detailed interference force and pressure data were obtained on a representative wing-body-nacelle combination at Mach numbers of 0.9 to 1.4. The model consisted of a delta wing-body aerodynamic force model with four independently supported nacelles located beneath the wing-body combination. The model was mounted on a six-component force balance, and the left-hand wing was pressure-instrumented. Each of the two right-hand nacelles was mounted on a six-component force balance housed in the thickness of the nacelle, while each of the left-hand nacelles was pressure-instrumented. The primary variables examined included Mach number, angle of attack, nacelle position, and nacelle mass-flow ratio. Four different configurations were tested to identify various interference forces and pressures on each component; these included tests of the isolated nacelle, the isolated wing-body combination, the four nacelles as a unit, and the total wing-body-nacelle combination. Nacelle axial location, relative to both the wing-body combination and to each other, was the most important variable in determining the net interference among the components.

Bencze, D. P.↗
NASA NTRS1973

Effect of rotor design tip seed on aerodynamic performance of a model VTOL lift fan under static and crossflow conditions

Results are presented for a wind tunnel investigation of three single VTOL lift fan stages designed for the same overall total pressure ratio at different rotor tip speeds. The stages were tested in a model lift fan installed in a wing pod. The three stages had essentially the same aerodynamic performance along the operating line. However, differences in stage thrust characteristics were obtained when a variation in back pressure was imposed on the stages by cross-flow effects and thrust-vectoring louvers.

Stockman, N. O.↗
NASA NTRS1973

The effect of aerodynamic parameters on power output of windmills

Aerodynamic results for a study on windpower generation are reported. Windmill power output is presented in terms that are commonly used in rotary wing analysis, namely, power output as a function of drag developed by the windmill. Effect of tip speed ratio, solidity, twist, wind angle, blade setting and airfoil characteristics are given.

Wiesner, W.↗
NASA NTRS1975

Entry heat transfer tests of the 0.006-scale space shuttle orbiter model (50-0) in Langley Research Center freon tunnel at Mach 6 (OH45)

Results are presented of heat transfer tests of a 147B configuration orbiter model (50-0) conducted in the NASA Langley Research Center Freon Tunnel (LRC/CF4). These tests were conducted at a nominal Mach number of 6, and at Reynolds numbers of 0.3 and 0.5 x 1,000,000 per foot. The objectives of the tests were to determine the effects of the low freon specific heat ratio, gamma, on the heating distributions and to determine the impingement of the orbiter bow shock on the wing. The data presented include thin skin heat transfer data (tabulated data and plotted data).

Foust, J. W.↗
NASA NTRS1986

Structureborne noise in aircraft: Modal tests

As part of an investigation to develop measurement techniques for structureborne noise, three modal surveys have been conducted on an OV-10A aircraft and the results have been presented. The purpose of the modal surveys was to identify suitable locations for mounting accelerometer and strain gages in subsequent tests in which transfer functions relating wing vibration to interior noise were to be determined. These surveys are as follows:(1) wing/fuselage modal survey utilizing one shaker under the right wing; (2) complete wing modal survey utilizing two shakers, one under each wing; and (3) fuselage side panel modal survey utilizing a small instrumented hammer. The predominant frequencies and damping ratios for each analysis were listed in tables. The primary mode shapes at the lower frequencies and at frequencies near the expected engine driving frequencies have been shown for each survey.

Clevenson, S. A.↗
NASA NTRS1988

Application of Hybrid Laminar Flow Control to Global Range Military Transport Aircraft

A study was conducted to evaluate the application of hybrid laminar flow control (HLFC) to global range military transport aircraft. The global mission included the capability to transport 132,500 pounds of payload 6500 nautical miles, land and deliver the payload and without refueling return 6500 nautical miles to a friendly airbase. The preliminary design studies show significant performance benefits obtained for the HLFC aircraft as compared to counterpart turbulent flow aircraft. The study results at M=0.77 show that the largest benefits of HLFC are obtained with a high wing with engines on the wing configuration. As compared with the turbulent flow baseline aircraft, the high wing HLFC aircraft shows 17 percent reduction in fuel burned, 19.2 percent increase in lift-to-drag ratio, an insignificant increase in operating weight, and a 7.4 percent reduction in gross weight.

Lange, Roy H.↗
NASA NTRS1990

Personnel launch system (PLS) lifting body and low lift-to-drag (L/D)

The Personnel Launch System (PLS) is a small transportation system designed to transport people, but no cargo, to and from low-earth orbit. The PLS is being considered as an addition to the manned launch capability of the United States for three main reasons: (1) to assure manned access to space, (2) to achieve a first-stage abort ability, and (3) to reduce operations costs. To those ends, two designs are being considered for the PLS that differ in their lift-to-drag (L/D) ratio. The Lyndon B. Johnson Space Center was assigned the task of examining low L/D capsules with no wings and a parachute landing capability. The Langley Research Center is studying a higher L/D PLS with wings and runway landings. Whichever design is selected, the PLS will act as a complement to the Space Shuttle fleet and will enhance the ability of our Nation to achieve reliable, safe, and cost-effective access to space flight, thus furthering the goals of the U.S. space program and increasing the safety of the human crews manning a future space station.

Erwin, Harry O.↗
NASA NTRS2008

Development of a Common Research Model for Applied CFD Validation Studies

The development of a wing/body/nacelle/pylon/horizontal-tail configuration for a common research model is presented, with focus on the aerodynamic design of the wing. Here, a contemporary transonic supercritical wing design is developed with aerodynamic characteristics that are well behaved and of high performance for configurations with and without the nacelle/pylon group. The horizontal tail is robustly designed for dive Mach number conditions and is suitably sized for typical stability and control requirements. The fuselage is representative of a wide/body commercial transport aircraft; it includes a wing-body fairing, as well as a scrubbing seal for the horizontal tail. The nacelle is a single-cowl, high by-pass-ratio, flow-through design with an exit area sized to achieve a natural unforced mass-flow-ratio typical of commercial aircraft engines at cruise. The simplicity of this un-bifurcated nacelle geometry will facilitate grid generation efforts of subsequent CFD validation exercises. Detailed aerodynamic performance data has been generated for this model; however, this information is presented in such a manner as to not bias CFD predictions planned for the fourth AIAA CFD Drag Prediction Workshop, which incorporates this common research model into its blind test cases. The CFD results presented include wing pressure distributions with and without the nacelle/pylon, ML/D trend lines, and drag-divergence curves; the design point for the wing/body configuration is within 1% of its max-ML/D. Plans to test the common research model in the National Transonic Facility and the Ames 11-ft wind tunnels are also discussed.

Vassberg, John C.↗
NASA NTRS2010

Conceptual Design of a Two Spool Compressor for the NASA Large Civil Tilt Rotor Engine

This paper focuses on the conceptual design of a two spool compressor for the NASA Large Civil Tilt Rotor engine, which has a design-point pressure ratio goal of 30:1 and an inlet weight flow of 30.0 lbm/sec. The compressor notional design requirements of pressure ratio and low-pressure compressor (LPC) and high pressure ratio compressor (HPC) work split were based on a previous engine system study to meet the mission requirements of the NASA Subsonic Rotary Wing Projects Large Civil Tilt Rotor vehicle concept. Three mean line compressor design and flow analysis codes were utilized for the conceptual design of a two-spool compressor configuration. This study assesses the technical challenges of design for various compressor configuration options to meet the given engine cycle results. In the process of sizing, the technical challenges of the compressor became apparent as the aerodynamics were taken into consideration. Mechanical constraints were considered in the study such as maximum rotor tip speeds and conceptual sizing of rotor disks and shafts. The rotor clearance-to-span ratio in the last stage of the LPC is 1.5% and in the last stage of the HPC is 2.8%. Four different configurations to meet the HPC requirements were studied, ranging from a single stage centrifugal, two axi-centrifugals, and all axial stages. Challenges of the HPC design include the high temperature (1,560deg R) at the exit which could limit the maximum allowable peripheral tip speed for centrifugals, and is dependent on material selection. The mean line design also resulted in the definition of the flow path geometry of the axial and centrifugal compressor stages, rotor and stator vane angles, velocity components, and flow conditions at the leading and trailing edges of each blade row at the hub, mean and tip. A mean line compressor analysis code was used to estimate the compressor performance maps at off-design speeds and to determine the required variable geometry reset schedules of the inlet guide vane and variable stators that would result in the transonic stages being aerodynamically matched with high efficiency and acceptable stall margins based on user specified maximum levels of rotor diffusion factor and relative velocity ratio.

Veres, Joseph P.↗
NASA NTRSDate not supplied

Upgrades to the Single Stage Axial Compressor and Fan Facility For Low Pressure Ratio and Boundary Layer Ingesting Fan Research

Next generation aircraft engine efficiency goals will be met through high bypass ratio engines. To achieve these goals, a combination of small core and low pressure ratio fan technologies will be necessary. Additionally, advanced propulsion airframe integration concepts, such as boundary layer propulsion, and distributed electrically driven fans with short inlets or wing integration strategies, are beginning to be investigated for their potential fuel burn savings. In order to realize the potential fuel savings from these technologies, it is necessary to have testing capabilities for the components. The NASA Glenn Research Center (GRC) Single Stage Axial Fan and Compressor Facility (also called the GRC W-8 Facility) has recently undergone several significant upgrades in order to effectively test low pressure ratio fans and various inlet distortions. This paper will outline various challenges to testing low pressure ratio fans and the methods implemented to ensure that the W-8 facility is capable of performing these tests and acquiring high quality data. The upgrades include significant piping upgrades to reduce pressure loss and turbulence, capability for inlet total pressure and swirl distortion, increased test section length including a longer shaft, a two component balance, an upgraded rotating data system, and a new temperature characterization to reduce uncertainties in thermocouple measurements.

W-8 facitlity↗