Search NASA⌕ Search

SEARCH · Search NASA

Results for “carbon neutrality”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Overview of the KSTAR experiments and future plan

The Korea Superconducting Tokamak Advanced Research (KSTAR) device has recently entered a new phase of operation following the installation of a tungsten mono-block divertor, providing a unique platform to investigate high-performance, long-pulse plasma scenarios for future reactors. The 2023–2024 experimental campaigns demonstrated significant progress in commissioning the tungsten divertor, developing plasma operation scenarios, and achieving real-time control. Comparative studies revealed increased core radiation losses and associated performance degradation relative to the carbon divertor environment. Alleviation strategies, such as optimized neutral beam injection timing, boron powder seeding, and impurity control through gas puffing, were shown to reduce tungsten accumulation and extend high-performance phases, including record H-mode operation exceeding 100 s. International collaboration enabled the first demonstration of high poloidal beta scenarios with an internal transport barrier on KSTAR. Advances in control included upgraded real-time resonant magnetic perturbation schemes and disruption forecasting. Furthermore, divertor detachment control using a new surrogate-model-based approach with real-time radiation imaging demonstrated active impurity and heat flux management. Supported by enhanced heating, current drive, and diagnostic systems, these achievements offer valuable insights into tungsten impurity behavior, transport physics, and control strategies for future reactors including ITER. Planned upgrades toward a full-tungsten wall and ITER-aligned real-time plasma control will further establish KSTAR as a leading experimental platform for developing operational scenarios required to achieve steady-state, burning plasma conditions.

KSTAR↗
DOE OSTI2020

Measurement of neutrino-induced neutral-current coherent $π^0$ production in the NOvA near detector

The cross section of neutrino-induced neutral-current coherent $\pi^0$ production on a carbon-dominated target is measured in the NOvA near detector. This measurement uses a narrow-band neutrino beam with the average neutrino energy of 2.7\,GeV, xwhich is of interest to the ongoing and future long-baseline neutrino oscillation experiments. The measured, flux-averaged cross section is $\sigma = 14.0\pm0.9$\,(stat.)$\pm2.1$\,(syst.)$\times 10^{-40}$ $\text{cm}^2/$nucleus, consistent with model prediction. This result is the most precise measurement of neutral-current coherent $\pi^0$ production in the few-GeV neutrino energy region.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS2014

Laboratory Determination of the Infrared Band Strengths of Pyrene Frozen in Water Ice: Implications for the Composition of Interstellar Ices

Broad infrared emission features (e.g., at 3.3, 6.2, 7.7, 8.6, and 11.3 micrometers) from the gas phase interstellar medium have long been attributed to polycyclic aromatic hydrocarbons (PAHs). A significant portion (10 to 20%) of the Milky Way's carbon reservoir is locked in PAH molecules, which makes their characterization integral to our understanding of astrochemistry. In molecular clouds and the dense envelopes and disks of young stellar objects (YSOs), PAHs are expected to be frozen in the icy mantles of dust grains where they should reveal themselves through infrared absorption. To facilitate the search for frozen interstellar PAHs, laboratory experiments were conducted to determine the positions and strengths of the bands of pyrene mixed with H2O and deuterium oxide ices. The deuterium oxide mixtures are used to measure pyrene bands that are masked by the strong bands of H2O, leading to the first laboratory determination of the band strength for the CH stretching mode of pyrene in water ice near 3.25 micrometers. Our infrared band strengths were normalized to experimentally determined ultraviolet (UV) band strengths, and we find that they are generally approximately 50% larger than those reported by Bouwman et al. (2011) based on theoretical strengths. These improved band strengths were used to reexamine YSO spectra published by Boogert et al. (2008) to estimate the contribution of frozen PAHs to absorption in the 5 to 8 micrometer spectral region, taking into account the strength of the 3.25 micrometer CH stretching mode. It is found that frozen neutral PAHs contain 5 to 9% of the cosmic carbon budget, and account for 2 to 9% of the unidentified absorption in the 5 to 8 micrometer region.

polycyclic aromatic hydrocarbons (PAHs)↗
DOE OSTI2021

Nanoporous weakly coordinating anionic frameworks (Final Technical Report)

Under this award, we synthesized and characterized new weakly coordinating, anionic covalent organic frameworks. The motivation was to expand the class of covalent organic frameworks though the introduction of the first weakly coordinating anionic ones. The significance of the weakly coordinating anionic character of these frameworks is associated with the character of the counter (metal) cations in their pores. Those counter-cations, due to the inability to effectively coordinate to the pore walls, have a “naked”, and thus highly electrophilic, Lewis acidic character. Such properties are expected to translate to a number of interesting physical properties that can be potentially used for a range of energy-relevant applications. One of these applications is gas adsorption, separation, and storage. The electrophilic, Lewis acidic character of the counter-cations are expected to strongly bind to gas molecules entering the pores leading to higher gas sorption capacities. Other applications include heterogeneous catalysis, ion exchange, and solid state ion conduction. Within the project we explored a range of chemical blocks, and tested synthesis conditions to polymerize these building blocks to form the target materials. In particular, we focused on materials with group 15 elements like phosphorus in the oxidation state +5 and the coordination number 6, that have a formal -1 charge. The synthesis of such materials is challenging because its success depends on the absence of residual monomeric and oligomeric side-products in the pores, and the absence of significant framework interpenetration. Crystalline forms of these materials require sufficient reversibility of the polymerization reaction (which is difficult to achieve because group 15 elements like P tend to make strong covalent bonds with neighbored elements), as well as suitable polymerization rates that prevent the formation of kinetically controlled products. We had success with the preparation of anionic porous organic frameworks with anionic building blocks containing P(V)O6 octahedra synthesized through Yamamoto coupling reactions. These materials are non-crystalline because of the irreversible nature of the Yamamoto coupling reaction, but show porosity. The porosity and surface area can be significantly increased by co-reaction with electrostatically neutral co-reactants. Very high porosity and surface areas can be achieved when the materials are washed with hydrochloric acid. This method is commonly used to free products from Yamamoto coupling reactions from by-products. Indeed, this method removed by products from the pores of our materials, however it also led to the hydrolysis of the PO6 octahedra to form pending phosphonic acid groups (-PO3H)-groups in the frameworks (PA-POFs) which was actually not desired. Nonetheless, these materials showed high CO2 sorption capacities. In addition, they show extremely high (actually record) sorption capacities for the removal of a range of common micropollutants such as bisphenol A (BPA) and 4-nitrophenol in water. BPA is a wide-spread organic pollutant and a known endocrine disruptor. The maximum adsorption capacity of BPA at equilibrium is found to be as high as 3,366 mg g-1 by Langmuir adsorption model, which is more than 10 times greater than peer materials. The polymer also rapidly removes various other organic micropollutants with more than 90% removal efficiencies. In addition, the PA-POF material can be regenerated at least five times by mild washing using methanol without significant loss in removal efficiency. This is significant advantage over commonly used activated carbon materials (that are in Brita water faucet filters, for example). Comparison studies showed that only materials with the phosphonate groups show extreme sorption although the number of PA group is actually small according to solid state NMR and EDX data. More research would be needed to investigate why this is (a possibility is that the phosphonate groups have a multiplying effect in which a PA-induced initial adsorption leads to the adsorption of much more adsorbate). The extreme sorption capabilities can also be visually seen when colored adsorbates such as 4-nitrophenol are used, as the adsorption of the nitrobenzene leads to the decoloration of the solution. We have produced three short videos that illustrate the sorption capabilities compared to two peer materials (activated carbon from dismantled Brita water filters, and a electrostatically neutral, chemically related, porous organic polymer, respectively).

36 MATERIALS SCIENCE↗
NASA NTRS2007

Biomedical Support of U.S. Extravehicular Activity

The world's first extravehicular activity (EVA) was performed by A. A. Leonov on March 18, 1965 during the Russian Voskhod-2 mission. The first US EVA was executed by Gemini IV astronaut Ed White on June 3, 1965, with an umbilical tether that included communications and an oxygen supply. A hand-held maneuvering unit (HHMU) also was used to test maneuverability during the brief EVA; however the somewhat stiff umbilical limited controlled movement. That constraint, plus difficulty returning through the vehicle hatch, highlighted the need for increased thermal control and improved EVA ergonomics. Clearly, requirements for a useful EVA were interrelated with the vehicle design. The early Gemini EVAs generated requirements for suits providing micro-meteor protection, adequate visual field and eye protection from solar visual and infrared radiation, gloves optimized for dexterity while pressurized, and thermal systems capable of protecting the astronaut while rejecting metabolic heat during high workloads. Subsequent Gemini EVAs built upon this early experience and included development of a portable environmental control and life support systems (ECLSS) and an astronaut maneuvering unit. The ECLSS provided a pressure vessel and controller with functional control over suit pressure, oxygen flow, carbon dioxide removal, humidity, and temperature control. Gemini EVA experience also identified the usefulness of underwater neutral buoyancy and altitude chamber task training, and the importance of developing reliable task timelines. Improved thermal management and carbon dioxide control also were required for high workload tasks. With the Apollo project, EVA activity was primarily on the lunar surface; and suit durability, integrated liquid cooling garments, and low suit operating pressures (3.75 pounds per square inch absolute [psia] or 25.8 kilopascal [kPa],) were required to facilitate longer EVAs with ambulation and significant physical workloads with average metabolic rates of 1000 BTU/hr and peaks of up to 2200 BTU/hr. Mobility was further augmented with the Lunar Roving Vehicle. The Apollo extravehicular mobility unit (EMU) was made up of over 15 components, ranging from a biomedical belt for capturing and transmitting biomedical data, urine and fecal containment systems, a liquid cooling garment, communications cap, a modular portable life support system (PLSS), a boot system, thermal overgloves, and a bubble helmet with eye protection. Apollo lunar astronauts performed successful EVAs on the lunar surface from a 5 psia (34.4 kPa) 100% oxygen environment in the Lunar Lander. A maximum of three EVAs were performed on any mission. For Skylab a modified A7LB suit, used for Apollo 15, was selected. The Skylab astronaut life support assembly (ALSA) provided umbilical support through the life support umbilical (LSU) and used open loop oxygen flow, rather than closed-loop as in Apollo missions. Thermal control was provided by liquid water circulated by spacecraft pumps and electrical power also was provided from the spacecraft via the umbilical. The cabin atmosphere of 5 psia (34.4 kPa), 70% oxygen, provided a normoxic atmosphere and because of the very low nitrogen partial pressures, no special protocols were required to protect against decompression sickness (DCS) as was the case with the Apollo spacecraft with a 5 psi, 100% oxygen environment.

Gernhardt, Michael L.↗
DOE OSTI2021

The controlling role of atmosphere in dawsonite versus gibbsite precipitation from tetrahedral aluminate species

In highly alkaline solution, aluminum speciates as the tetrahedrally coordinated aluminate monomer, Al(OH)4- and/or dimer Al2O(OH)62-, yet precipitates as octahedrally coordinated gibbsite (Al(OH)3). This tetrahedral to octahedral transformation governs Al precipitation, which is crucial to worldwide Al production, and to the processing of caustic high-level radioactive wastes. Despite its significance, the transformation pathway remains unknown. Here we explore the roles of atmospheric water and carbon dioxide in mediating the transformation of the tetrahedrally coordinated potassium aluminate dimer salt (K2Al2O(OH)6) to gibbsite versus potassium dawsonite (KAl(CO3)(OH)2). A combination of in-situ attenuated total reflection infrared spectroscopy, ex-situ micro X-ray diffraction, and multivariate curve resolution-alternating least squares chemometrics analysis reveals that humidity plays a key role in the transformation by limiting the amount of alkalinity neutralization by dissolved CO2. Lower humidity favors higher alkalinity and incorporation of carbonate species in the final Al product to form KAl(CO3)(OH)2. Higher humidity enables more acid generation that destabilizes dawsonite and favors gibbsite as the solubility limiting phase. Because the transformation was restricted to occur in thin water films, the results suggest that transition from tetra- to octahedrally coordinated Al does not have to occur in bulk solution, as has often been hypothesized, but may instead appear on the source mineral surface.

Dembowski, Mateusz↗
NASA NTRS1976

Feasibility study of launch vehicle ground cloud neutralization

The distribution of hydrogen chloride in the cloud was analyzed as a function of launch pad geometry and rate of rise of the vehicle during the first 24 sec of burn in order to define neutralization requirements. Delivery systems of various types were developed in order to bring the proposed chemical agents in close contact with the hydrogen chloride. Approximately one-third of the total neutralizing agent required can be delivered from a ground installed system at the launch pad; concentrated sodium carbonate solution is the preferred choice of agent for this launch pad system. Two-thirds of the neutralization requirement appears to need delivery by aircraft. Only one chemical agent (ammonia) may be reasonably considered for delivery by aircraft, because weight and bulk of all other agents are too large.

Vanderarend, P. C.↗
NASA NTRS2014

Evaluating the Adsorptive Capabilites of Chemsorb 1000 and Chemsorb 1425

The removal of trace contaminants from spacecraft cabin air is necessary for crew health and comfort during long duration space exploration missions. The air revitalization technologies used in these future exploration missions will evolve from current ISS ISS State-of-Art (SOA) and is being designed and tested by the Advanced Exploration Systems (AES) Program's Atmosphere Resource Recovery and Environmental Monitoring (ARREM) project. The ARREM project is working to mature optimum atmosphere revitalization and environmental monitoring system architectures to enable exploration beyond Lower Earth Orbit (LEO). The Air Revitalization Lab at KSC is one of six NASA field centers participating in the ARREM that specializes in adsorbent and catalyst characterization with simulated spacecraft gas streams using combinations of pressure, O2 partial pressure, CO2 partial pressure, and humidity that are representative of a range of anticipated cabin atmospheric conditions and loads. On board ISS, the Trace Contaminant Control Subassembly (TCCS) provides active control of trace contaminants from the cabin atmosphere utilizing physical adsorption, thermal catalytic oxidation, and chemical adsorption processes. High molecular weight contaminants and ammonia (NH3) are removed a granular activated carbon treated with approx. 10% by weight phosphoric acid (H3PO4) (B-S Type 3032 4×6 mesh), which is expendable and is periodically refurbished. The Type 3032 granular activated carbon bed is no longer commercially available and therefore it is important to characterize the efficiency and capacity of commercially available NH3 sorbents. This paper describes the characterization of two Molecular Products LTD activated carbons: Chemsorb 1000 and Chemsorb 1425. Untreated activated carbons (e.g. Chemsorb 1000) remove contaminants by physisorption, which concentrates the contaminant within the pores of the carbon while letting air to pass through the sorbent4. Low molecular weight or polar gases (e.g. HCl, SO2, formaldehyde, and NH3) are not removed by physisorption and typically require chemisorption for removal. Treated activated carbons (e.g. Chemsorb 1425) are impregnated with a a chemical agent (e.g. phosphoric acid) that reacts with those gases, converting them to solids or salts within the carbon and removes them from the air stream. This process occurs via neutralization or catalysis reactions and adsorption capacity is exhaustedwhen the available impregnated chemicals are consumed. Moisture affects removal performance since adsorption sites within the pores are filled with water. The performance of impregnated carbons may be enhanced by moisture content because the mechanisms of contaminant removal are chemical reactions that occur in reagents contained within the pores. The adsorptive capacity data (mol/kg) of Chemsorb 1000 and 1425 for gas mixtures (ethanol, acetone, toluene, acetaldehyde, dichloromethane, and xylene) was measured with 40% relative humidity at 23 deg C air temperature. The adsorptive capacity data (mol/kg) of Chemsorb 1425 was measured using NH3 gas streams.

adsorptive capacities↗
DOE OSTI2023

Electrochemical Reduction of Flue Gas Carbon Dioxide to Commercially Viable C2-C4 Products (Final Report)

This is the final scientific/technical report for a DOE project focused on the electrochemical conversion of CO 2 in non-aqueous solvents to novel products. Electrochemical reduction of CO 2 provides an attractive route to produce valuable fuels and chemicals that can simultaneously lower greenhouse gas emissions when powered by renewable electricity. While recent technological advances have shown the feasibility of industrial CO 2 electroreduction, many challenges remain to improve this technology and expand the list of economically viable products. The vast majority of electrochemical CO 2 reduction research has been conducted in aqueous media under neutral to alkaline conditions, leading to commonly reported products including carbon monoxide, formic acid, methane, methanol, ethylene, acetic acid, and ethanol. In comparison, non-aqueous media for CO 2 reduction has been underexplored but represents a possible avenue to yield new products and improved operating conditions. The aim of the project was to convert waste CO 2 in the form of flue gas to a multicarbon C2 - C4 chemical product in a reactor designed to achieve economically competitive values of current density and selectivity. The project strived to advance the technology readiness of an electrochemical CO 2 reduction process in alcohol solvents from the proof-of-concept stage to a device capable of meeting performance metrics for commercial viability. In the initial plan, the University of Louisville researchers were to focus on investigating the electrochemical process and improving the faradaic efficiency for novel C2 – C4 species, while also working on a parallel effort to build a practical electrolysis reactor to markedly increase the CO 2 reduction current density. The reactor development effort also aimed to engineer a dual-electrolyte feed strategy with non-aqueous catholyte and aqueous anolyte to promote water oxidation as the coupling anodic half-reaction to enable a sustainable and economical overall process. At the outset, the University of North Dakota was to investigate the feasibility of operating directly from coal-derived flue gas without separate capture and purification. The research team sought to determine impurity effects and test mitigation strategies, as well as engineer the gaseous feed system for high reactor tolerance to lower CO 2 concentration. In the last half year of the project, the focus was planned to shift to integrating the advances in the catalysis, electrochemical conditions, reactor design, and flue gas compatibility into a fully functional device and improve it for maximum current density and faradaic efficiency for C2 – C4 species. Knowledge of the full system components, constraints, and maximum performance was then to be used as the basis for a thorough technoeconomic analysis (TEA) and life cycle analysis (LCA) at the end of the project.

01 COAL, LIGNITE, AND PEAT↗
NASA NTRS1987

Ara OB1 - A stellar association formed by the action of an energetic event?

Neutral hydrogen (at the wavelength of 21 cm) and carbon monoxide (at 2.6 mm) line observations of the interstellar medium in the neighborhood of the association Ara OB1 are reported. The observed H I distribution indicates the presence of an expanding structure. The total H I mass associated with such feature amounts to 4800 solar masses, and its momentum and kinetic energy are about 40,000 solar mass km/s and 3 x 10 to the 48th erg, respectively. The H I structure, 42 pc in diameter, expands at a speed of 10 km/s. A possible origin for the expanding H I structure, and a genetic link between such structure and Ara OB1 are proposed.

Arnal, E. M.↗
DOE OSTI2021

Simulation of the SPARC plasma boundary with the UEDGE code

Here in this work, the UEDGE edge transport code is used to examine conditions in the SPARC divertor and edge plasma for various levels of carbon impurity and power from the core (P SOL ). A double-null magnetic configuration is simulated assuming up-down symmetry in geometry and physics. The anomalous heat and particle transport coefficients are tuned to match empirical predictions for SPARC's midplane density profiles, target plate heat flux profiles, and inner/outer divertor power sharing. Convective transport is included on the low-field side, while on the high-field side the transport is modeled as purely diffusive. Hydrogen neutrals are modeled as a fluid with inertial effects, and a carbon impurity is included using the fixed-fraction model. We find that detachment induced by impurity seeding could significantly reduce the heat flux to the divertor surfaces in the SPARC tokamak. At P SOL = 28 MW (the value predicted for SPARC's full-power H-mode scenario) cases with both divertor legs detached were obtained with a carbon impurity fraction between 0.3%–1.4%, far below Z eff limits for SPARC. When the plasma in the outer leg is detached, the peak heat flux density perpendicular to the target plate is below 1 MW m -2 , electron and ion temperatures are less than 1.5 eV, and momentum detachment is observed. However, the detachment state is found to be sensitive to the side-wall boundary conditions, the level of neutral pumping, and the target plate tilt. Finally, a broadly similar SOLPS simulation of SPARC is used to assess the appropriateness of the simpler impurity and neutral models used in UEDGE.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Application of electrodialysis pretreatment to enhance boron removal and reduce fouling during desalination by nanofiltration/reverse osmosis

we report membranes have emerged as promising technologies for treatment of non-traditional waters, but fouling and poor rejection of small, neutral solutes (e.g., boric acid) impede their further implementation for water purification. Boron rejection is increased by raising the pH to convert boric acid to borate ion, but this change often leads to calcite supersaturation. This study investigated the use of a hybrid electrodialysis-nanofiltration/reverse osmosis (ED-NF/RO) system to reduce fouling from calcite precipitation and calcium-polysaccharide sorption to NF/RO membranes. Also, the study examined the potential of the hybrid process to increase permeate flux and boron rejection during NF/RO of synthetic saline water. ED pretreatment reduced calcite oversaturation and reduced flux decline during NF/RO. Low alginate concentrations (25 mg/L) limited NF/RO fouling, but high concentrations (100 mg/L) appeared to promote calcite scaling. ED pretreatment reduced the osmotic pressure of the NF/RO feed water, enabling lower operating pressures or greater permeate water fluxes. Boron rejection during NF/RO increased with ED pretreatment, probably due to stronger electrostatic repulsion and an increase in the fraction of total boron present as B(OH)4- following ED. This hybrid ED-NF/RO system shows promise as a novel approach to enhancing the performance of current membrane systems for treating complex feed waters.

alginate↗
DOE OSTI2021

Long-Lived Triplet Excited State in a Heterogeneous Modified Carbon Nitride Photocatalyst

Heterogeneous carbon nitrides have numerous advantages as photocatalysts, including strong light absorption, tunable band edges, and scalability, but their performance and continued development are limited by fast charge recombination and an under-developed mechanistic understanding of photodriven interfacial electron transfer. These shortcomings are a result of complex photophysics, leading to rate asynchrony between oxidation and reduction, as well as redox processes driven out of electronic trap states rather than excited states. We show that a well-defined triplet excited state in cyanamide-modified carbon nitride is realized with appropriately sized particles. The utility of this long-lived excited state is demonstrated by its ability to drive a hydroamidation photoredox cycle. By the tuning of the particle size of CN x , the oxidation–reduction photochemistry of carbon nitride may be balanced to achieve a redox-neutral closed photocatalytic cycle. Here, these results uncover a triplet excited state chemistry for appropriately sized CNx particles that preludes a rich energy and electron transfer photochemistry for these materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1984

The laboratory simulation of unmagnetized supernova remnants Absence of a blast wave

Supernova remnants are experimentally simulated by irradiating spherical targets with eight-beam carbon dioxide laser in a chamber containing finite amounts of neutral gas, the gas being ionized by radiation from the hot target. The expansion velocities of the target plasmas are approximately the same as the expansion velocities of supernova ejecta and the experiment is successfully scaled to the case of a supernova remnant in an unmagnetized, low-density, interstellar medium. No sweep-up of the ambient plasma is detected, indicating that no hydrodynamic shock wave is formed to couple the target ejecta to the ambient gas. The experiment implies that if supernova ejecta couple to the interstellar medium, magnetic-field effects may be crucial to the physical description.

Borovsky, J. E.↗
NASA NTRS1984

Physical Properties of the Uranian Satellites

Recent work on the satellites of Uranus revealed many of their basic physical properties. Radiometric measurements showed that the Ariel, Umbriel, Titania and Oberon have diameters which range from 1630 to 1110 km and albedos which range from 0.30 to 0.18. Spectrophotometric observations of Miranda suggest that it may have the highest albedo of the known Uranian satellites and a diameter of about 500 km. Near-infrared measurements show that Ariel, Titania and Oberon have the largest known opposition surges. All five known satellites of Uranus have surfaces which are composed of water ice contaminated with small amounts of dark material. The dark material on the surfaces of Ariel, Umbriel, Titania and Oberon is spectrally bland and has spectral similarities to carbon black, charcoal, carbonaceous chondritic material and other dark, spectrally neutral materials. Recent density determinations suggest that there may be large density differences among Ariel, Umbriel, Titania and Oberon, with density increasing with distance from Uranus.

Brown, R. H.↗
NASA NTRS2005

Scattering of Solar X-Rays by Jupiter and Saturn

Soft X-ray emission has been observed from the disk of both Jupiter and Saturn as well as from the auroral regions of these planets. The low-latitude disk emission as observed by ROSAT, the Chandra X-Ray Observatory, and XMM-Newton appears to be uniformly distributed across the disk and to be correlated with solar activity. These characteristics suggest that the source of the disk x-rays are: (1) elastic scattering of solar X-rays by atmospheric neutrals (2) absorption of solar X-rays in the carbon K-shell followed by fluorescent emission. The carbon atoms are found in methane molecules located below the homopause. In this paper we present the results of calculations of the scattering albedo and of the emitted x-ray intensity for a range of atmospheric abundances and for a number of solar irradiance spectra. The model calculations are compared with recent x-ray observations of Jupiter and Saturn.

Cravens, T. E.↗