Search NASA⌕ Search

SEARCH · Search NASA

Results for “cathode loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

456 records · Page 26

The effect of zinc additions on the environmental stability of Alloy 8090 (Al-Li-Cu-Mg-Zr)

Stress corrosion cracking (SCC) remains a problem in both Al-Li and conventional Al heat treatable alloys. It has recently been found that relatively small additions (less than or approximately 1 wt-percent) of Zn can dramatically improve the SCC performance of alloy 8090 (Al-Li-Cu-Mg-Zr). Constant load time to failure experiments using cylindrical tensile samples loaded between 30 and 85 percent of TYS indicate improvements of orders of magnitude over the baseline 8090 for the Zn-containing alloys under certain aging conditions. However, the toughnesses of the alloys were noticeably degraded due to the formation of second phase particles which primarily reside on grain and subgrain boundaries. EDS revealed that these intermetallic particles were Cu and Zn rich. The particles were present in the T3 condition and were not found to be the result of quench rate, though their size and distribution were. At 5 hours at 160 C, the alloys displayed the greatest susceptibility to SCC but by 20 hours at 160 C the alloys demonstrated markedly improved TTF lifetimes. Aging past this time did not provide separable TTF results, however, the alloy toughnesses continued to worsen. Initial examination of the alloys microstructures at 5 and 20 hours indicated some changes most notably the S' and delta' distributions. A possible model by which this may occur will be explored. Polarization experiments indicated a change in the trend of E(sub BR) and passive current density at peak aging as compared to the baseline 8090. Initial pitting experiments indicated that the primary pitting mechanism in chloride environments is one occurring at constituent (Al-Fe-Cu) particles and that the Cu and Zn rich boundary precipitates posses a breakaway potential similar to that of the matrix acting neither anodic or cathodic in the first set of aerated 3.5 w/o NaCl experiments. Future work will focus on the identification of the second phase particles, evaluation of K(sub 1SCC) and plateau da/dt via both DCB and slow strain rate techniques. A lower Zn content variant will be examined in the near future in hopes of optimizing toughness, density and SCC performance.

Kilmer, Raymond J.↗

A conformal heat-drying direct ink writing 3D printing for high-performance lithium-ion batteries

High areal capacity electrodes hold great potential for high-energy density lithium-ion batteries (LIBs), but their poor electrochemical kinetics limit their power density. Here, in this study, high areal capacity 3D-structured LiNi 0.8 Mn 0.1 Co 0.1 O 2 cathodes (4.3 mAh cm -2 ) are prepared via 3D printing with a manner of direct ink writing. The electrodes had an enlarged electrode–electrolyte contact area, shortened diffusion pathway, and reduced intercalation-induced stress, thereby delivering enhanced rate capability and cyclability in LIBs, which is 143.6 mAh g -1 at 3C and a 60.2 % capacity retention over 800 cycles at 1C. Moreover, at electrode level, the 3D-NMC exhibits an energy and power densities of 313.1 Wh kg -1 and 657.9 W kg -1 , respectively. Furthermore, the theoretical calculation suggests that reducing the gap width will be highly beneficial to the energy and power densities. This work establishes a milestone in understanding the cycling effect on the electrode local structure, including the void area and the LiNi 0.8 Mn 0.1 Co 0.1 O 2 region, which confirms the effectiveness of 3D printing for electrode preparation.

25 ENERGY STORAGE↗

Exploring the potential and impact of single-crystal active materials on dry-processed electrodes for high-performance lithium-ion batteries

Roll-to-roll powder-to-film dry processing (DP) and single-crystal (SC) active materials (AMs) with many advantages are two hot topics of lithium-ion batteries (LIBs). However, DP of SC AMs for LIBs is rarely reported. Consequently, the impact of SC AMs on dry-processed LIBs is not well understood. Herein, for the first time, via a set of experimental and theoretical studies of the conventional polycrystalline-AM- and SC-AM-based DPed electrodes (DPEs), this work not only reports a high-performance dry SC-AM cathode for LIB manufacturing, but also establishes some fundamental understanding of SC-based dry-processed electrodes, including their morphology, structure, mechanical strength, electronic conductivity and LIB electrochemical behavior. Further, the results suggest that DP of SC AMs is promising, which can dramatically improve the electrochemical kinetics at electrode level and particle level. Specifically, for the rate capability and long-term cyclability in full cells, SC DPEs exhibit a discharge specific capacity of 152.1 mAh g -1 at 1C and a capacity retention rate of 79.9 % at C/3 over 500 cycles, which are superior to those of PC DPEs (135.6 mAh g -1 and 68.3 %) at the same conditions and are further confirmed by the simulation data from the theoretical modelling study. Therefore, this comprehensive work marks a significant milestone for DP strategy and SC AMs, enlightening future research and development of LIB manufacturing.

25 ENERGY STORAGE↗

Elucidating the Role of Single-Atom Pd for Electrocatalytic Hydrodechlorination

In this study, we loaded Pd catalysts onto a reduced graphene oxide (rGO) support in an atomically dispersed fashion [i.e., Pd single-atom catalysts (SACs) on rGO or Pd 1 /rGO] via a facile and scalable synthesis based on anchor-site and photoreduction techniques. The as-synthesized Pd 1 /rGO significantly outperformed the Pd nanoparticle (Pdnano) counterparts in the electrocatalytic hydrodechlorination of chlorinated phenols. Downsizing Pd nano to Pd 1 leads to a substantially higher Pd atomic efficiency (14 times that of Pdnano), remarkably reducing the cost for practical applications. The unique single-atom architecture of Pd 1 additionally affects the desorption energy of the intermediate, suppressing the catalyst poisoning by Cl – , which is a prevalent challenge with Pdnano. Characterization and experimental results demonstrate that the superior performance of Pd 1 /rGO originates from (1) enhanced interfacial electron transfer through Pd–O bonds due to the electronic metal–support interaction and (2) increased atomic H (H*) utilization efficiency by inhibiting H 2 evolution on Pd 1 . Furthermore, this work presents an important example of how the unique geometric and electronic structure of SACs can tune their catalytic performance toward beneficial use in environmental remediation applications.

36 MATERIALS SCIENCE↗

Impact of electrode porosity architecture on electrochemical performances of 1 mm-thick LiFePO4 binder-free Li-ion electrodes fabricated by Spark Plasma Sintering

Thick electrodes with high active material loadings have been intensively studied over the last couple of decades in pursuit of achieving high energy density systems. To optimize and enhance the electrochemical performance of such electrodes, one has to control the pore morphology by, for example, varying the pore size and shape, and the level of porosity. In the present work, the fabrication of thick binder-free LiFePO4 (LFP) electrodes with two different pore sizes (12 and 20 mu m) and porosities (21 vol% and 44 vol%) using Spark Plasma Sintering (SPS) and templating approach is reported. The well-controlled porous architecture inside the thick electrodes is realized by fine-tuning experimental parameters. The impact of porosity architecture on electrochemical performance is quantified and correlated with the 3D tortuosity values determined from both micro-computed tomography and electrochemical impedance-based experimental methods. Based on the micro-computed tomography data analysis, estimated tortuosity values along X, Y, and Z axes reveal an anisotropic effect perpendicularly to the SPS compression axis (Z-direction). This is particularly profoundly observed in the samples with larger pores (20 mu m). The correlation between morphological properties and the rate capability performance is established indicating that the capacity loss happens mainly due to the Li-ion diffusion limitations.

Cathode material↗

Dynamic, Adaptive, Systems and Materials: Complex, Simple and Emergent Behaviors

This program has been funded by DoE/BES for twenty years. It has moved into and out of various subjects as it has developed, but it has retained its focus on complexity and complex systems. The project has evolved in the following way: Self-Assembly and Biomimetic Self-Assembly: All self-assembling systems depend upon a minimum of two types of interaction: a repulsion and an attraction. For the familiar molecular systems, attractive interactions are typically hydrogen bonds and electrostatic interactions. Repulsive interactions include steric effects, hydrophobic effects (in biological systems), and charge-charge repulsion. We have expanded this repertoire to include surface interactions, magnetic interactions, and others. I list these systems in the order in which we have explored them: i) A key emphasis in current work is in understanding how the movement of ions in a magnetic field (the Lorentz effect) interacts with catalytic systems. We have demonstrated that an acceleration in rate of reduction of CO 2 to CO can be accomplished by applying an external magnetic field. This acceleration is largely due to the application of the Lorentz effect on mass transport at the catalyst’s surface. ii) We have also extensively explored the influence of electrostatics, as exhibited in self-assembling systems, by tribocharging. iii) Another key system involves surface tension effects; examples include interactions between heavy particles floating at a liquid-air interface, and interacting by changes in surface area; interactions of bubbles and bubble rafts, behaviors of bubble trains in microfluidic networks, and behaviors of microorganisms in constraining environments. iv) This work has intentionally de-emphasized biological systems; but it does include some work on protein-ligand interactions and interactions among microorganisms. v) We have also explored applications of some of these effects, these explorations include bubble rafts as diffraction gratings, exploration of the structures that can be obtained by tribocharging and uses of these structures in exploring nucleation and melting of crystals. vi) Although not a major focus of this work, several other topics have emerged and offer opportunities for future work. These include the behavior of bubble trains and bubble rafts in microfluidic systems. A particularly interesting example is the formation of bubble trains that repeat in the alteration of large and small bubbles according to rules we do not presently understand, but are uniquely large-period oscillating systems. These systems offer a new route into understanding the instabilities of the type represented by oscillations. vii) We have also begun exploratory projects on magnetic levitation (especially to determine molecular density), and information storage (in molecules). Magnetic Levitation: Self-assembling and biomimetic systems require both attraction and repulsion. We have used electrostatics (tribocharging), interfacial free-energies (surface tension and related forces) and others. Potential uses include reconfigurable diffraction gratings and liquid lenses; exploration of mechanisms in tribocharging; tunneling in EGaIn junctions; and bubble trains (especially in micro-fluidic systems). Examples of systems representing these topics is included in the following papers: Complexity: Disks rotating at a water-air interface; Benard-Marangoni effects; Vortex-Crystals from spinning magnetic disks (Marangoni effects); EGaIn Electrode to study quantum tunneling; Self-Assembly of electrostatically-charged metallic spheres (electrets); Dynamically reconfigurable lens; Using computational designs of ligands for enzymes; Electrostatic self-assembly by tribocharging; Monodisperse bubble trains in microchannel systems; Inverted dripping faucet; Flames; Printing of micro-organisms to regenerate the “ink” of printing device; Using micro-organisms to move loads (“microoxen”); Motion of bacterial swarms near surfaces; Making monodisperse particles in microfluidic systems; Coding/decoding of information stored in droplet trains in microfluidic networks; Magnetic levitation; and Information storage. i) Tribocharging. The change in focus of this work on electrets from the fundamentals of charging to applications of these materials in studying self-assembly using electrostatic interactions. ii) Bubbles in Microchannels. The realization that systems of bubbles in microchannels represented a major opportunity to study complexity in a very tractable system, and the development of a semi-quantitative theory of this subject. iii) Flames. The growth of “flames” remains an exploratory subject for the research, although their currently relatively little active work involving it ongoing. iv) Systems with Microorganisms. The removal of work in biological systems from this project. Based on work supported in this program, we now have a significant project on the development of microfluidic tools for studying C. elegans (a nematode), but this work was not appropriate for a program focused on complexity, and we developed separate support for it. (It is, however, an example of successful seeding of a new area by BES.) The work on electrets has gone through a period in which a part of the program was the subject of a MURI; the focus of this work was to develop materials that did not charge electrostatically on friction or contact. The MURI is now over, and the work on dynamic self-assembly (supported by BES) is the major focus. “Flames” has also enjoyed synergistic support, in terms of a project supported by DARPA on flame suppression (in the absence of extinguishing agents, using acoustic and electrostatic interactions). This work was helpful in understanding some of the basics of flames, but is entirely distinct from the BES focus in complexity. A growing interest is in the Lorentz effect. The Lorentz effect is the force exerted on charged particles (electrons, ions, charged molecules) when they move through a perpendicular magnetic field. The Lorentz effect is almost ubiquitous in modern technology: examples of applications include electric motors, dynamos, cathode ray tubes, many batteries, and most systems that control electrical currents with magnetic forces. We have begun to explore the Lorentz effect in electrochemical systems and heterogeneous catalytic systems involving charged organic species and inorganic ions. This work is still at an early stage, but initial studies that Lorentz effects can be large when ions move through magnetic fields, or magnetic fields move in the presence of ions.

36 MATERIALS SCIENCE↗