Results for “design and process development” — Page 26

NASA NTRS2017

Conceptual Feasibility Study of the Hyperloop Vehicle for Next-Generation Transport

The Hyperloop concept is proposed as a faster, cheaper alternative to high-speed rail and traditional short-haul aircraft. It consists of a passenger pod traveling through a tube under light vacuum while being propelled and levitated by a combination of permanent and electro-magnets. The concept addresses NASA's research thrusts for growth in demand, sustainability, and technology convergence for high-speed transport. Hyperloop is a radical departure from other advanced aviation concepts, however it remains an aeronautics concept that tackles the same strategic goals of low-carbon propulsion and ultra-effcient vehicles. System feasibility was investigated by building a multidisciplinary vehicle sizing model that takes into account aerodynamic, thermodynamic, structures, electromagnetic, weight, and mission analyses. The sizing process emphasized the strong coupling between the two largest systems: the tube and the passenger pod. The model was then exercised to examine Hyperloop from a technical and cost perspective. The structural sizing analysis of the travel tube demonstrates potential for signi cant capital cost reductions by considering an underwater route. Examination of varying passenger capacity indicates that the system can be operated with a wide range of passenger loads without significant change in operating expenses. Lastly, a high-level sizing study simulated variations in tube area, pressure, pod speed, and passenger capacity showing that there is a tube pressure that minimizes operating energy usage. The value of this optimal tube pressure is highly sensitive to numerous design details. These combined estimates of energy consumption, passenger throughput, and mission analyses all support Hyperloop as a faster and cheaper alternative to short-haul flights. The tools and expertise used to quantify these results also demonstrate how traditional aerospace design methods can be leveraged to handle the complex and coupled design process. Much of the technology development required for the Hyperloop is shared with next-generation aircraft. Furthermore, the substantial public interest and active commercial development make it an ideal candidate as an aircraft technology driver and test bed.

Hyperloop Vehicle↗

NASA NTRSDate not supplied

Leveraging CSPP: Building a cloud based direct broadcast processing system

Reducing the time that it takes to have useful satellite information is very important because timely access allows for more informed decision making. This is especially true in time critical situations like disaster response and financial market analysis. One way to achieve reductions in the overall time between information capture and delivery to use the direct broadcast from weather satellites. In this work, we describe a state driven satellite information system that captures a satellite’s direct broadcast signal and uses cloud-based resources to provide end-user controlled processing. The system takes advantage of the reliability and customizability of Amazon Web Services to provide fast and reliable access to a system that takes the direct broadcast signal and leverages the CSPP software as well as dynamically supplied end-user processing modules to produce a user desired information product. Finally, we describe the development process and how a flexible design allowed for changes as the capabilities of the processing platform evolved and the lessons we learned from the process.

CSPP↗

NASA NTRSDate not supplied

An Integrated Design Tool for Tow-Steered Laminates of Composites in Abaqus and MSC.Patran/Nastran

Tow-steered composites can be tailored for optimal mechanical performance of lightweight structures. However, there are no commercial-grade design tools for tow-steered composite structures, which hinders the design innovation of tow-steered composites in realistic structures. The novelty of this paper is to develop an integrated design framework along with the development of graphical user interface (GUI) plug-ins in commercial finite element (FE) software Abaqus and MSC.Patran/Nastran. The GUI plug-ins take all the design setups and communicate with external codes for the material modeling and optimization, and hence provide a unified design environment within the FE codes. The mechanics of structure genome (MSG) plate model computes shell element properties based on user-defined fiber paths and layup, which are defined via the GUI plug-ins. The optimization is performed by an open-source code, Dakota, from Sandia National Laboratories (Sandia), which also coordinates the structural analysis, material modeling, and optimization in design iterations. Two examples are presented to demonstrate the user-friendliness and versatility of the developed GUI plug-ins. The developed tools will ease the design process and facilitate the application of tow-steered composites in realistic aerospace structures.

Xin Liu↗

NASA NTRSDate not supplied

An Integrated Design Tool for Tow-Steered Laminates of Composites in Abaqus and MSC.Patran/Nastran

Tow-steered composites can be tailored for optimal mechanical performance of lightweight structures. However, there are no commercial-grade design tools for tow-steered composite structures, which hinders the design innovation of tow-steered composites in realistic structures. The novelty of this paper is to develop an integrated design framework along with the development of graphical user interface (GUI) plug-ins in commercial finite element (FE) software Abaqus and MSC.Patran/Nastran. The GUI plug-ins take all the design setups and communicate with external codes for the material modeling and optimization, and hence provide a unified design environment within the FE codes. The mechanics of structure genome (MSG) plate model computes shell element properties based on user-defined fiber paths and layup, which are defined via the GUI plug-ins. The optimization is performed by an open-source code, Dakota, from Sandia National Laboratories (Sandia), which also coordinates the structural analysis, material modeling, and optimization in design iterations. Two examples are presented to demonstrate the user-friendliness and versatility of the developed GUI plug-ins. The developed tools will ease the design process and facilitate the application of tow-steered composites in realistic aerospace structures.

Xin Liu↗

NASA NTRS2003

Developments at the Advanced Design Technologies Testbed

A report presents background and historical information, as of August 1998, on the Advanced Design Technologies Testbed (ADTT) at Ames Research Center. The ADTT is characterized as an activity initiated to facilitate improvements in aerospace design processes; provide a proving ground for product-development methods and computational software and hardware; develop bridging methods, software, and hardware that can facilitate integrated solutions to design problems; and disseminate lessons learned to the aerospace and information technology communities.

VanDalsem, William R.↗

NASA NTRS2011

Auto Draw from Excel Input Files

The design process often involves the use of Excel files during project development. To facilitate communications of the information in the Excel files, drawings are often generated. During the design process, the Excel files are updated often to reflect new input. The problem is that the drawings often lag the updates, often leading to confusion of the current state of the design. The use of this program allows visualization of complex data in a format that is more easily understandable than pages of numbers. Because the graphical output can be updated automatically, the manual labor of diagram drawing can be eliminated. The more frequent update of system diagrams can reduce confusion and reduce errors and is likely to uncover symmetric problems earlier in the design cycle, thus reducing rework and redesign.

Strauss, Karl F.↗

NASA NTRS2004

Performance and Reliability Optimization for Aerospace Systems subject to Uncertainty and Degradation

This report summarizes work performed by the Space Systems Laboratory (SSL) for NASA Langley Research Center in the field of performance optimization for systems subject to uncertainty. The objective of the research is to develop design methods and tools to the aerospace vehicle design process which take into account lifecycle uncertainties. It recognizes that uncertainty between the predictions of integrated models and data collected from the system in its operational environment is unavoidable. Given the presence of uncertainty, the goal of this work is to develop means of identifying critical sources of uncertainty, and to combine these with the analytical tools used with integrated modeling. In this manner, system uncertainty analysis becomes part of the design process, and can motivate redesign. The specific program objectives were: 1. To incorporate uncertainty modeling, propagation and analysis into the integrated (controls, structures, payloads, disturbances, etc.) design process to derive the error bars associated with performance predictions. 2. To apply modern optimization tools to guide in the expenditure of funds in a way that most cost-effectively improves the lifecycle productivity of the system by enhancing the subsystem reliability and redundancy. The results from the second program objective are described. This report describes the work and results for the first objective: uncertainty modeling, propagation, and synthesis with integrated modeling.

Miller, David W.↗

NASA NTRS2023

NASA High Temperature Alloy Development – GRX-810

Problem: Conventional materials and processing techniques limit the design of combustor domes used in jet turbine engines. Proposed Solution: Develop a high ductility, high temperature material for an additively manufactured (AM) combustor fuel nozzle and dome for supersonic aircraft (>1093°C (2000°F) operating temperature).

T Smith↗

NASA NTRS2009

Wooden Spaceships: Human-Centered Vehicle Design for Space

Presentation will focus on creative human centered design solutions in relation to manned space vehicle design and development in the NASA culture. We will talk about design process, iterative prototyping, mockup building and user testing and evaluation. We will take an inside look at how new space vehicle concepts are developed and designed for real life exploration scenarios.

Twyford, Evan↗

NASA NTRSDate not supplied

TBIRD, a rapid prototyping approach for design, assembly, and test of a LEO-to-ground lasercom CubeSat

The TeraByte InfraRed Delivery (TBIRD) system is a 3U payload on a 6U CubeSat launched in May 2022 which has now demonstrated space to ground links of >1 Terabyte (TB) per pass at a max data rate of 200Gbps. As a CubeSat mission, the development of the TBIRD payload was focused on low SWaP and a “rapid prototyping” approach which accepted higher risks to accelerate the schedule and reduce costs. The optomechanical design process followed standard in-house processes to develop a system that would be robust to LEO environmental loads, with a focus on the stability of the transmit (Tx) and receive (Rx) channel performance metrics. The driving requirement of maintaining 20μrad pointing error between the TX and Rx channels forced specific attention to thermal and mechanical load changes over operational conditions, which drove major design decisions. This paper describes some of engineering challenges overcome and approaches used to make TBIRD a successful program, as well as some of the tradeoffs of rapid prototyping precision optical payloads. TBIRD successfully met and exceeded the total downlink requirements listed above, with a bandwidth of 200Gbps and a total downlink of 4.8TB of information in a single pass.

TBIRD↗

NASA NTRS1982

Bank Record Processing

Barnett Banks of Florida, Inc. operates 150 banking offices in 80 Florida cities. Banking offices have computerized systems for processing deposits or withdrawals in checking/savings accounts, and for handling commercial and installment loan transactions. In developing a network engineering design for the terminals used in record processing, an affiliate, Barnett Computing Company, used COSMIC's STATCOM program. This program provided a reliable network design tool and avoided the cost of developing new software.

Source record↗

NASA NTRS1983

Rotating-Machinery Critical Speeds

Computer program available from COSMIC provides quick, efficient, and accurate results in support of preliminary and proposed rotating-machinery designs. Advanced rotating-machinery design is iterative process in early stages of development. New program provides timely, critical-speed calculations to support preliminary rotating-machinery designs.

Beatty, R. F.↗

NASA NTRS1980

Industry involvement in IPAD through the Industry Technical Advisory Board

In 1976 NASA awarded The Boeing Company a contract to develop IPAD (Integrated Programs for Aerospace-Vehicle Design). This contract included a requirement for Boeing to form an Industrial Technical Advisory Board (ITAB), with members representing major aerospace and computer companies. The purpose of this board was to guide the development of IPAD. The specific goal of IPAD is to increase United States aerospace industry productivity through the application of computers to manage engineering data. This goal clearly is attainable; in fact, IPAD's influence can reach beyond the aerospace industry to many businesses where product development is based on the design-building process. An enhanced IPAD, therefore, is a national asset of significance. The role of ITAB in guiding the development of this system is described.

Swanson, W. E.↗

NASA NTRS1997

Advanced Technology Composite Fuselage - Materials and Processes

The goal of Boeing's Advanced Technology Composite Aircraft Structures (ATCAS) program was to develop the technology required for cost and weight efficient use of composite materials in transport fuselage structure. This contractor report describes results of material and process selection, development, and characterization activities. Carbon fiber reinforced epoxy was chosen for fuselage skins and stiffening elements and for passenger and cargo floor structures. The automated fiber placement (AFP) process was selected for fabrication of monolithic and sandwich skin panels. Circumferential frames and window frames were braided and resin transfer molded (RTM'd). Pultrusion was selected for fabrication of floor beams and constant section stiffening elements. Drape forming was chosen for stringers and other stiffening elements. Significant development efforts were expended on the AFP, braiding, and RTM processes. Sandwich core materials and core edge close-out design concepts were evaluated. Autoclave cure processes were developed for stiffened skin and sandwich structures. The stiffness, strength, notch sensitivity, and bearing/bypass properties of fiber-placed skin materials and braided/RTM'd circumferential frame materials were characterized. The strength and durability of cocured and cobonded joints were evaluated. Impact damage resistance of stiffened skin and sandwich structures typical of fuselage panels was investigated. Fluid penetration and migration mechanisms for sandwich panels were studied.

Scholz, D. B.↗

NASA NTRS2000

Formal Analysis of the Remote Agent Before and After Flight

This paper describes two separate efforts that used the SPIN model checker to verify deep space autonomy flight software. The first effort occurred at the beginning of a spiral development process and found five concurrency errors early in the design cycle that the developers acknowledge would not have been found through testing. This effort required a substantial manual modeling effort involving both abstraction and translation from the prototype LISP code to the PROMELA language used by SPIN. This experience and others led to research to address the gap between formal method tools and the development cycle used by software developers. The Java PathFinder tool which directly translates from Java to PROMELA was developed as part of this research, as well as automatic abstraction tools. In 1999 the flight software flew on a space mission, and a deadlock occurred in a sibling subsystem to the one which was the focus of the first verification effort. A second quick-response "cleanroom" verification effort found the concurrency error in a short amount of time. The error was isomorphic to one of the concurrency errors found during the first verification effort. The paper demonstrates that formal methods tools can find concurrency errors that indeed lead to loss of spacecraft functions, even for the complex software required for autonomy. Second, it describes progress in automatic translation and abstraction that eventually will enable formal methods tools to be inserted directly into the aerospace software development cycle.

Havelund, Klaus↗

NASA NTRS2002

An Evaluation of the ROSE System

A request-oriented scheduling engine, better known as ROSE, is under development within the Flight Projects Directorate for the purpose of planning and scheduling of the activities and resources associated with the science experiments to be performed aboard the International Space Station (ISS). ROSE is being designed to incrementally process requests from payload developers (PDs) to model and schedule the execution of their science experiments on the ISS. The novelty of the approach comes from its web-based interface permitting the PDs to define their request via the construction of a graphical model to represent their requirements. Based on an examination of the current ROSE implementation, this paper proposes several recommendations for changes to the modeling component and makes mention of other potential applications of the ROSE system.

John M. Usher↗

NASA NTRSDate not supplied

Bypass Duct Acoustic Liner Design With and Without Bifurcation Effects

The growth in air traffic and the commitment to sustainable aviation continue to provide new challenges to reducing aircraft noise levels. Acoustic liner design methodologies must therefore provide the capability to efficiently predict the acoustic benefits of novel liner configurations within complex aircraft nacelle geometries. With these observations in mind, a broadband acoustic liner optimization process has been developed and assessed through a series of design and experimental studies at increasing technology readiness levels. This work applies the design process to the aft-fan noise component and explores the effects of bypass duct bifurcations (e.g., the pylon and lower bifurcation). In addition to this new application, the design study is expanded to include the use of a commercially available duct propagation code. Despite the different general workflow for the two propagation codes, consistent optimized impedance spectra and in-duct attenuation predictions were obtained for several acoustic treatment options. The preliminary results are promising, and this work increases confidence in the enhanced broadband liner design methodology and lays the groundwork for complimentary use of the codes in future studies. The potential benefits of acoustic treatment on the upper and lower bifurcations are also demonstrated. The knowledge gained through this preliminary stage of the liner design process will be used to guide the identification of candidate liner designs for a proposed static engine test within the next year.

Acoustic Liner Design↗

NASA NTRSDate not supplied

Bypass Duct Acoustic Liner Design with and without Bifurcation Effects

The growth in air traffic and the commitment to sustainable aviation continue to provide new challenges to reducing aircraft noise levels. Acoustic liner design methodologies must therefore provide the capability to efficiently predict the acoustic benefits of novel liner configurations within complex aircraft nacelle geometries. With these observations in mind, a broadband acoustic liner optimization process has been developed and assessed through a series of design and experimental studies at increasing technology readiness levels. This work applies the design process to the aft-fan noise component and explores the effects of bypass duct bifurcations (e.g., the pylon and lower bifurcation). In addition to this new application, the design study is expanded to include the use of a commercially available duct propagation code. Despite the different general workflow for the two propagation codes, consistent optimized impedance spectra and in-duct attenuation predictions were obtained for several acoustic treatment options. The preliminary results are promising, and this work increases confidence in the enhanced broadband liner design methodology and lays the groundwork for complimentary use of the codes in future studies. The potential benefits of acoustic treatment on the upper and lower bifurcations are also demonstrated. The knowledge gained through this preliminary stage of the liner design process will be used to guide the identification of candidate liner designs for a proposed static engine test within the next year.

Acoustic Liner Design↗