Search NASA⌕ Search

SEARCH · Search NASA

Results for “diffractive computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

High-Resolution Infrared Spectra of Spiropentane, C5H8

Infrared spectra of spiropentane (C{sub 5}H{sub 8}) have been recorded at a resolution (0.002 cm{sup -1}) sufficient to resolve for the first time individual rovibrational lines. This initial report presents the ground state constants for this molecule determined from the detailed analysis of the {nu}16 (b2) parallel band at 993 cm{sup -1}. In addition, the determination included more than 2000 ground state combination-differences deduced from partial analyses of four other infrared-allowed bands, the {nu}24(e) perpendicular band at 780 cm{sup -1} and three (b2) parallel bands at 1540 cm{sup -1} ({nu}14), 1568 cm{sup -1} ({nu}5+{nu}16), and 2098 cm{sup -1} ({nu}5+{nu}14). In each of the latter four cases, the spectra show complications; in the case of {nu}24, these complications are due to rotational l-type doublings, and in the case of the parallel bands, the spectral complexities are due to Fermi resonance and Coriolis interactions of the upper states with nearby levels. The unraveling of these is underway but the assignment of many of these transitions permit the confident use of the ground state differences in determining the following constants for the ground state (in units of cm{sup -1}): B0 = 0.1394736(2), DJ = 2.458(1) x 10{sup -8}, DJK = 8.28(3) x 10{sup -8}. For the unperturbed {nu}16 fundamental, more than 3000 transitions were fit and the band origin was found to be at 992.53793(2) cm{sup -1}. The numbers in parentheses are the uncertainties (two standard deviations) in the value of the last digit of the constants. Surprisingly, the very accurate B0 value measured here is lower than the value (0.1418 cm{sup -1}) calculated from an electron diffraction structure, instead of being higher, as expected. Where possible, the rovibrational results are compared with those computed at the anharmonic level using the B3LYP density functional method with a cc-pVTZ basis set. These too suggest that the electron diffraction results are in question.

74 ATOMIC AND MOLECULAR PHYSICS↗

A roadmap to uranium ionic liquids: Anti-crystal engineering

In the search for uranium-based ionic liquids, tris(N,N-dialkyldithiocarbamato)uranylates have been synthesized as salts of the 1-butyl-3-methylimidazolium (C 4 mim) cation. As dithiocarbamate ligands binding to the UO 2 2+ unit, tetra-, penta-, hexa-, and heptamethylenedithiocarbamates, N,N-diethyldithiocarbamate, N-methyl-N-propyldithiocarbamate, N-ethyl-N-propyldithiocarbamate, and N-methyl-N-butyldithiocarbamate have been explored. X-ray single-crystal diffraction allowed unambiguous structural characterization of all compounds except N-methyl-N-butyldithiocarbamate, which is obtained as a glassy material only. In addition, powder X-ray diffraction as well as vibrational and UV/Vis spectroscopy, supported by computational methods, were used to characterize the products. Differential scanning calorimetry was employed to investigate the phase-transition behavior depending on the N,N-dialkyldithiocarbamato ligand with the aim to establish structure–property relationships regarding the ionic liquid formation capability. Compounds with the least symmetric N,N-dialkyldithiocarbamato ligand and hence the least symmetric anions, tris(N-methyl-N-propyldithiocarbamato)uranylate, tris(N-ethyl-N-propyldithiocarbamato)uranylate, and tris(N-methyl-N-butyldithiocarbamato)uranylate, lead to the formation of (room-temperature) ionic liquids, which confirms that low-symmetry ions are indeed suitable to suppress crystallization. As a result, these materials combine low melting points, stable complex formation, and hydrophobicity and are therefore excellent candidates for nuclear fuel purification and recovery.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Analysis of Coronado State Historic Site artifacts using X‐rays

Abstract Two historic‐period metal artifacts were provided by the New Mexico Historic Sites to Los Alamos National Laboratory for non‐destructive analysis. The artifacts were a crossbow quarrel (or bolthead) and a reliquary pendant recovered from Kuaua Pueblo (also known as the Coronado Historic Site) in Bernalillo, NM. The quarrel is a heavily patinated metal that had been flattened due to compressive forces. The pendant consisted of a metal casing that had previously surrounded two center gemstones on the front and rear face of the pendant. The gemstone in the rear setting had fractured and was displaced from the setting, leaving only a small, loose fragment within the pendant for study. The front gem appeared to be very dark, near‐black in color, and the fragment of the rear gem was a bright red color. The artifacts were analyzed to ascertain their composition and glean insight into their provenance using the following X‐ray techniques: X‐ray computed tomography, confocal micro X‐ray fluorescence, and X‐ray diffraction. Infrared spectroscopy and electron microscopy were used on selected areas. Ultraviolet Raman spectra were collected on the two gems and the pendant. The metal material of the artifacts was found to be primarily composed of copper. The gems in the pendant were composed of manganese (front gem) and calcium (side gem).

36 MATERIALS SCIENCE↗

Densification and microstructure features of lithium hydride fabrication

The manufacturing of lithium hydride (LiH) utilizing uniaxial pressing, which offers fabrication with tailorable properties via microstructure control, can lead to the expansion in application of LiH while bypassing the challenges presented by historical casting manufacturing techniques. Through control of consolidation conditions such as pressure, temperature, dwell time and powder load, the presented work highlights the densification of LiH, with an emphasis on quantifying oxygen content, for applications requiring a specific density range necessary for optimized material performance. Karl Fischer Titration and X-ray Diffraction proved useful in determining oxygen and phase content while Computed Tomography and Scanning Electron Microscopy provided structural analysis. The temperature dependent densification of LiH fit with an Arrhenius term resulted in an activation energy of 21.2 kJ/mol. Images of fractured surfaces of LiH pressed at 500 °C revealed drastic grain coarsening, aided by the presence of oxygen impurities.

36 MATERIALS SCIENCE↗

The formation mechanisms of interlocked microstructures in low-carbon high-strength steel weld metals

Microstructural features and the formation mechanisms of interlocked microstructures of acicular ferrite in a low-carbon high-strength steel weld metal were investigated by means of computer-aided three-dimensional reconstruction technique and electron backscattered diffraction analysis. Multiple nucleation on inclusions, sympathetic nucleation or repeated nucleation, hard impingement, mutual intersection, and fixed orientation relationships of acicular ferrite grains were observed. They were all responsible for the formation of interlocked microstructures in the weld metal. During the process of isothermal transformation, the pre-formed acicular ferrite laths or plates partitioned austenite grains into many small and separate regions, and the growth of later formed acicular ferrite grains was confined in these small regions. Thus, the crystallographic grain size became smaller with the increasing holding time. Highlights: Black-Right-Pointing-Pointer Acicular ferrite is formed by multiple nucleation and sympathetic nucleation. Black-Right-Pointing-Pointer Hard impingement and intersection of ferrite grains occur at later stages. Black-Right-Pointing-Pointer The pre-formed ferrite laths partition austenite grains into smaller regions. Black-Right-Pointing-Pointer The growth of later formed ferrite grains is confined in the smaller regions.

36 MATERIALS SCIENCE↗

Denoising atomic resolution 4D scanning transmission electron microscopy data with tensor singular value decomposition

Tensor singular value decomposition (SVD) is a method to find a low-dimensional representation of data with meaningful structure in three or more dimensions. Here, tensor SVD has been applied to denoise atomic-resolution 4D scanning transmission electron microscopy (4D STEM) data. On data simulated from a SrTiO 3 [100] perfect crystal and a Si [110] edge dislocation, tensor SVD achieved an average peak signal-to-noise ratio (PSNR) of ~40 dB, which matches or exceeds the performance of other denoising methods, with processing times at least 100 times shorter. On experimental data from SrTiO 3 [100] and LiZnSb [11 2 ¯ 0]/GaSb [110] samples, tensor SVD denoises multiple GB 4D STEM data sets in ten minutes on a typical personal computer. Denoising with tensor SVD improves both convergent beam electron diffraction patterns and virtual-aperture annular dark field images.

36 MATERIALS SCIENCE↗

Tunable Magnetic Exchange between Rare-Earth Metal 5d and Iron 3d States: A Case Study of the Multiple Magnetic Transitions in Gd 6 FeBi 2 and the Solid Solutions Dy 6– x Gd x FeBi 2 (1 ≤ x ≤ 5) with Curie Temperatures in the Range 120–350 K

In this paper, the room-temperature magnet Gd 6 FeBi 2 was comprehensively characterized by means of temperature-dependent single-crystal X-ray diffraction, magnetization measurements, and experimental electron density and electronic structure computations. This work explores the electron-spin effects of Fe on this structure and suggests that Gd6FeBi2 shows structural features and exchange interactions, which are clearly distinguishable from other analogues, including the solid solutions Dy 6–x Gd x FeBi 2 (0 ≤ x ≤ 5). The unique traits of Gd 6 FeBi 2 and its derivatives encompass abnormal variations of lattice parameters with the temperature, as well as the presence of multiple magnetic transitions of complex nature. Based on the comprehensive analyses, it can be suggested that the unique magnetic response in this material is the result from tunable Fe spin states, which are coupled with strong Gd 5d–Fe 3d interactions, which differ from other members of this large, structural family. In the ground state, according to density functional theory calculations, the Fe atom carries two net electrons, whose spins are coupled in an antiparallel fashion to the spins of the Gd electrons. Near the Curie temperature, the Fe net moment is reduced intermittently, coupled with a multiple of magnetic transitions. The magnetic correlations are manifested in unexpected variations of the lattice parameters as a function of temperature, suggesting spin–lattice interactions. Furthermore, this study emphasizes the important role of Gd 5d electrons in tuning Fe 3d-based magnetic contribution, which enables better understanding on the spin coupling in other related compounds and sheds light on the development of new magnetic and spintronic compounds.

36 MATERIALS SCIENCE↗

Machine Learning Automated Analysis of Enormous Synchrotron X-ray Diffraction Datasets

X-ray diffraction (XRD) data analysis can be a time-consuming and laborious task. Deep neural network (DNN) based models trained with synthetic XRD patterns have been proven to be a highly efficient, accurate, and automated method for analyzing common XRD data collected from solid samples in ambient environments. However, it remains unclear whether synthetic XRD-based models can be effective in solving micro(μ)-XRD mapping data for in situ experiments involving liquid phases, which always have lower quality and significant artifacts. In this study, we collected μ-XRD mapping data from a LaCl 3 -calcite hydrothermal fluid system and trained two categories of models to analyze the experimental XRD patterns. Here, the models trained solely with synthetic XRD patterns showed low accuracy (as low as 64%) when solving experimental μ-XRD mapping data. However, the accuracy of the DNN models significantly improved (90% or above) when we trained them with a data set containing both synthetic and a small number of labeled experimental μ-XRD patterns. This study highlights the importance of labeled experimental patterns in training DNN models to solve μ-XRD mapping data from in situ experiments involving liquid phases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

State-of-Charge Investigation of Lithium Manganese Dioxide Primary Batteries Utilizing X-ray Computed Tomography

Lithium primary batteries (LPBs) represent a class of energy storage devices, uniquely suited for mission-critical applications including emergency backup power, aerospace and defense electronics, implantable medical devices, and remote sensing. Despite their technological maturity and distinct advantages over rechargeable lithium-ion batteries (i.e., superior shelf life and operational simplicity), state-of-charge (SoC) estimation in these batteries remains a persistent challenge due to the lack of a reliable, quantifiable diagnostic technique. In this work, we investigate X-ray computed tomography (X-CT) as a transformative and accurate SoC estimation technique for LPBs. Results gained through X-CT measurements reveal systematic, quantifiable structural changes in cathode morphology and geometry during discharge, establishing a direct structural basis for SoC estimation, with a maximum relative standard deviation of 2.3%. This work establishes a pathway toward operando, imaging-driven SoC diagnostics that can significantly enhance the reliability of SoC estimation in LPBs.

25 ENERGY STORAGE↗

Extraordinary Redox Activities in Ladder-Type Conjugated Molecules Enabled by B ← N Coordination-Promoted Delocalization and Hyperconjugation

The introduction of B ← N coordinate bond-isoelectronic to C-C single bond-into π-systems represents a promising strategy to impart exotic redox and electrochromic properties into conjugated organic molecules and macromolecules. To achieve both reductive and oxidative activities using this strategy, a cruciform ladder-type molecular constitution was designed to accommodate oxidation-active, reduction-active, and B ← N coordination units into a compact structure. Two such compounds (BN-F and BN-Ph) were synthesized via highly efficient N-directed borylation. These molecules demonstrated well-separated, two reductive and two oxidative electron-transfer processes, corresponding to five distinct yet stable oxidation states, including a rarely observed boron-containing radical cation. Spectroelectrochemical measurements revealed unique optical characteristics for each of these reduced/oxidized species, demonstrating multicolor electrochromism with excellent recyclability. Distinct color changes were observed between each redox state with clear isosbestic points on the absorption spectra. Here, the underlying redox mechanism was elucidated by a combination of computational and experimental investigations. Single-crystal X-ray diffraction analysis on the neutral state, the oxidized radical cation, and the reduced dianion of BN-Ph revealed structural transformations into two distinct quinonoid constitutions during the oxidation and reduction processes, respectively. B ← N coordination played an important role in rendering the robust and reversible multistage redox properties, by extending the charge and spin delocalization, by modulating the π-electron density, and by a newly established hyperconjugation mechanism.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanosecond in situ transmission electron microscope studies of the reversible Ge{sub 2}Sb{sub 2}Te{sub 5} crystalline <==> amorphous phase transformation

Chalcogenide-based phase-change materials have wide use in optical recording media and are growing in importance for use in non-volatile electronic memory. For both applications, rapid switching between the amorphous and crystalline phases is necessary, and understanding the changes during rapidly driven phase transitions is of scientific and technological significance. Laser-induced crystallization and amorphization occur rapidly and changes in atomic structure, microstructure, and temperature are difficult to observe experimentally and determine computationally. We have used nanosecond-scale time-resolved diffraction with intense electron pulses to study Ge{sub 2}Sb{sub 2}Te{sub 5} during laser crystallization. Using a unique and unconventional specimen geometry, cycling between the amorphous and crystalline phases was achieved, enabling in situ transmission electron microscope (TEM) study of both microstructural and crystallographic changes caused by repeated switching. Finite element analysis was used to simulate interactions of the laser with the nano-structured specimens and to model the rapidly changing specimen temperature. Such time-resolved experimental methods combined with simulation of experimentally inaccessible physical characteristics will be fundamental to advancing the understanding of rapidly driven phase transformations.

36 MATERIALS SCIENCE↗

Technology Enabling Zero-EPZ Micro Modular Reactors: Fabrication of Zirconium Hydride with Controlled Hydrogen Loading

This report completes Milestone M2.2.2 - ZrH pellet fabricated with controlled hydride loading: ZrH1.5±0.1 single phase pellets fabricated with controlled and thermally stable hydride loading. Hydrogen content to be quantified and single-phase confirmed by X-ray diffraction. In this milestone, we report the successful fabrication of delta-phase zirconium hydride pellets using the ORNL bulk metal hydriding system. The successful deployment of zirconium hydride moderator in advanced reactors requires development of a consistent and affordable production pathway along with implementation of a hydrogen retention solution throughout the reactor life. Fabrication of delta-phase zirconium hydride is challenging since the absorption of a large amount of hydrogen into alpha-zirconium induces significant volume expansion and the present hydrogen concentration gradient results in cracking. A fully programmable hydriding system with continuous hydrogen partial pressure and flow control to facilitate processing of massive metal hydride has been developed at ORNL. In this report, the working principle of the hydriding system will be introduced. Characterization of the produced zirconium hydride includes X-ray powder diffraction to identify the present phases and X-ray Computed Tomography to visualize the internal microstructure (including cracks). The results indicate that single delta-phase zirconium hydride pellets with various sizes have been successfully produced.

36 MATERIALS SCIENCE↗

New main reflector, subreflector and dual chamber concepts for compact range applications

A compact range is a facility used for the measurement of antenna radiation and target scattering problems. Most presently available parabolic reflectors do not produce ideal uniform plane waves in the target zone. Design improvements are suggested to reduce the amplitude taper, ripple and cross polarization errors. The ripple caused by diffractions from the reflector edges can be reduced by adding blended rolled edges and shaping the edge contour. Since the reflected edge continues smoothly from the parabola onto the rolled surface, rather than being abruptly terminated, the discontinuity in the reflected field is reduced which results in weaker diffracted fields. This is done by blending the rolled edges from the parabola into an ellipse. An algorithm which enables one to design optimum blended rolled edges was developed that is based on an analysis of the continuity of the surface radius of curvature and its derivatives across the junction. Futhermore, a concave edge contour results in a divergent diffracted ray pattern and hence less stray energy in the target zone. Design equations for three-dimensional reflectors are given. Various examples were analyzed using a new physical optics method which eliminates the effects of the false scattering centers on the incident shadow boundaries. A Gregorian subreflector system, in which both the subreflector and feed axes are tilted, results in a substantial reduction in the amplitude taper and cross polarization errors. A dual chamber configuration is proposed to eliminate the effects of diffraction from the subreflector and spillover from the feed. A computationally efficient technique, based on ray tracing and aperture integration, was developed to analyze the scattering from a lossy dielectric slab with a wedge termination.

Pistorius, C. W. I.↗

Optics Program Modified for Multithreaded Parallel Computing

A powerful high-performance computer program for simulating and analyzing adaptive and controlled optical systems has been developed by modifying the serial version of the Modeling and Analysis for Controlled Optical Systems (MACOS) program to impart capabilities for multithreaded parallel processing on computing systems ranging from supercomputers down to Symmetric Multiprocessing (SMP) personal computers. The modifications included the incorporation of OpenMP, a portable and widely supported application interface software, that can be used to explicitly add multithreaded parallelism to an application program under a shared-memory programming model. OpenMP was applied to parallelize ray-tracing calculations, one of the major computing components in MACOS. Multithreading is also used in the diffraction propagation of light in MACOS based on pthreads [POSIX Thread, (where "POSIX" signifies a portable operating system for UNIX)]. In tests of the parallelized version of MACOS, the speedup in ray-tracing calculations was found to be linear, or proportional to the number of processors, while the speedup in diffraction calculations ranged from 50 to 60 percent, depending on the type and number of processors. The parallelized version of MACOS is portable, and, to the user, its interface is basically the same as that of the original serial version of MACOS.

Lou, John↗

Diffraction pattern simulation of cellulose fibrils using distributed and quantized pair distances

Intensity simulation of X-ray scattering from large twisted cellulose molecular fibrils is important in understanding the impact of chemical or physical treatments on structural properties such as twisting or coiling. This paper describes a highly efficient method for the simulation of X-ray diffraction patterns from complex fibrils using atom-type-specific pair-distance quantization. Pair distances are sorted into arrays which are labelled by atom type. Histograms of pair distances in each array are computed and binned and the resulting population distributions are used to represent the whole pair-distance data set. These quantized pair-distance arrays are used with a modified and vectorized Debye formula to simulate diffraction patterns. This approach utilizes fewer pair distances in each iteration, and atomic scattering factors are moved outside the iteration since the arrays are labelled by atom type. As a result, this algorithm significantly reduces the computation time while maintaining the accuracy of diffraction pattern simulation, making possible the simulation of diffraction patterns from large twisted fibrils in a relatively short period of time, as is required for model testing and refinement.

09 BIOMASS FUELS↗

Layered synthetic microstructures as Bragg diffractors for X rays and extreme ultraviolet - Theory and predicted performance

The theory of X-ray diffraction by periodic structures is applied to the layered synthetic microstructures (LSMs) made possible by recent developments in thin film technology, and approximate formulas for estimating their performance are presented. A more complete computation scheme based on optical multilayer theory is also described, and it is shown that the diffracting properties may be tailored to specific applications by adjusting the refractive indices and thicknesses of the component layers. The theory may be modified to take account of imperfections in the LMS structure, and the properties of nonperiodic structures thereby computed. Structures with high integrated reflectivity constructed according to the methods defined have potential application in many areas of X-ray or EUV research and instrumentation.

Underwood, J. H.↗

General optics evaluation program

Computer program GENOPTICS is generalized aid for analysis and evaluation of optical systems that employ lenses, mirrors, diffraction gratings, and other geometrical optical surfaces. It can exactly trace up to 800 rays through as many as 40 surfaces. Results can be used to compute third order aberation coefficients including spheric contributions.

Howell, B. J.↗

Analysis of Self-Similar Solutions of Multidimensional Conservation Laws

This project brought large-scale, advanced methods for numerical solution of PDE to bear on the two-dimensional Riemann problem and obtained numerical solution of problem. This numerical solution allowed us to describe key features of the solution. Analysis was combined with numerical solution to explain these numerical results. High-resolution, large-scale numerical computations show for the first time that a shock forms strictly in the supersonic region. Numerical solutions appear to show the disappearance of a diffracting shock at a sonic line.

97 MATHEMATICS AND COMPUTING↗