Search NASA⌕ Search

SEARCH · Search NASA

Results for “dynamic analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Dynamic mechanical analysis of fiber reinforced composites

Dynamic mechanical and thermal properties were determined for unidirectional epoxy/glass composites at various fiber orientation angles. Resonant frequency and relative logarithmic decrement were measured as functions of temperature. In low angle and longitudinal specimens a transition was observed above the resin glass transition temperature which was manifested mechanically as an additional damping peak and thermally as a change in the coefficient of thermal expansion. The new transition was attributed to a heterogeneous resin matrix induced by the fiber. The temperature span of the glass-rubber relaxation was found to broaden with decreasing orientation angle, reflecting the growth of fiber contribution and exhibiting behavior similar to that of Young's modulus. The change in resonant frequency through the glass transition was greatest for samples of intermediate fiber angle, demonstrating behavior similar to that of the longitudinal shear modulus.

Reed, K. E.↗
NASA NTRS1986

Dynamic dielectric analysis - A means for process control

The development of dynamic dielectric analysis techniques (as a 'smart' sensor for quantitative NDE) and of intelligent closed-loop cure systems is reported. The cure process of both BF3:R-catalyzed and uncatalyzed tetraglycidyl-4,4'-diaminodiphenyl methane (TGDDM)/diamine epoxy resins was studied. Measurements were made over a frequency range of six decades. The resin was monitored continuously throughout the cure process as it changed from a viscous liquid to a highly crosslinked solid. From the frequency dependence of the dielectric loss, the specific conductivity has been determined and shown to directly monitor the viscosity before the gel point is reached. Dielectric master plots of the cure process, analogous to time-temperature superposition plots for rheological data, have been developed.

Kranbuehl, D.↗
NASA NTRS1983

Integrated verification and testing system (IVTS) for HAL/S programs

The IVTS is a large software system designed to support user-controlled verification analysis and testing activities for programs written in the HAL/S language. The system is composed of a user interface and user command language, analysis tools and an organized data base of host system files. The analysis tools are of four major types: (1) static analysis, (2) symbolic execution, (3) dynamic analysis (testing), and (4) documentation enhancement. The IVTS requires a split HAL/S compiler, divided at the natural separation point between the parser/lexical analyzer phase and the target machine code generator phase. The IVTS uses the internal program form (HALMAT) between these two phases as primary input for the analysis tools. The dynamic analysis component requires some way to 'execute' the object HAL/S program. The execution medium may be an interpretive simulation or an actual host or target machine.

Senn, E. H.↗
NASA NTRS1981

Advanced superposition methods for high speed turbopump vibration analysis

The small, high pressure Mark 48 liquid hydrogen turbopump was analyzed and dynamically tested to determine the cause of high speed vibration at an operating speed of 92,400 rpm. This approaches the design point operating speed of 95,000 rpm. The initial dynamic analysis in the design stage and subsequent further analysis of the rotor only dynamics failed to predict the vibration characteristics found during testing. An advanced procedure for dynamics analysis was used in this investigation. The procedure involves developing accurate dynamic models of the rotor assembly and casing assembly by finite element analysis. The dynamically instrumented assemblies are independently rap tested to verify the analytical models. The verified models are then combined by modal superposition techniques to develop a completed turbopump model where dynamic characteristics are determined. The results of the dynamic testing and analysis obtained are presented and methods of moving the high speed vibration characteristics to speeds above the operating range are recommended. Recommendations for use of these advanced dynamic analysis procedures during initial design phases are given.

Nielson, C. E.↗
NASA NTRS1983

Large Deployable Reflector (LDR) feasibility study update

In 1982 a workshop was held to refine the science rationale for large deployable reflectors (LDR) and develop technology requirements that support the science rationale. At the end of the workshop, a set of LDR consensus systems requirements was established. The subject study was undertaken to update the initial LDR study using the new systems requirements. The study included mirror materials selection and configuration, thermal analysis, structural concept definition and analysis, dynamic control analysis and recommendations for further study. The primary emphasis was on the dynamic controls requirements and the sophistication of the controls system needed to meet LDR performance goals.

Alff, W. H.↗
NASA NTRS1985

Design of Multivariable Controllers Using the Integrated Analysis Capability (IAC)

Dynamic analysis and controls design for flexible spacecraft involves high-order dynamic systems with multiple inputs and outputs. Computer tools are essential for such analysis. The controls/structures interaction analysis capability of an inter-disciplinary computer software system, called the Integrated Analysis Capability (IAC), is described. An overview of IAC components and procedures is presented, and an example of a preliminary space station controls design is shown.

Bossi, J. A.↗
NASA NTRS1988

Dynamic workspace analysis of two cooperating robot arms

The main objective of dynamic workspace analysis is to determine the maximum force/moment that the robots can generate jointly at each point within their common workspace. The authors develop a conceptually simple procedure to solve this problem. This procedure models the two cooperating robot arms as a closed-chain system and is based on the theory of linear transformations and the properties of mechanics.

Tarn, T. J.↗
NASA NTRS2022

A Survey of Mathematical Structures for Lunar Networks

To sustain the current and increasing accessibility of space, a scalable communications infrastructure (i.e. the Solar System Internet, SSI) is necessary. The goal of this paper is to begin the discovery of the fundamental underlying mathematical structure of space networks to help the research community harness these structures for algorithm development and optimization. To ensure the applicability of the research, the approaches are considered through the lens of simulated scenarios inspired by the Artemis Back-to-the-Moon mission set for 2024. We note that any approach to an SSI must fit under the umbrella of Delay Tolerant Networking (DTN), due to celestial mobility, high link latencies, high variance in link latencies, disconnections, lack of end-to-end paths, and so on. These difficulties are exacerbated by the fact that the underlying structure of a space network is a time-evolving network and may experience multiple discontinuities in its topology. In this paper we propose several novel approaches to a mathematical foundation for Delay Tolerant Networking Theory that fall outside the traditional scope of temporal network theory. These techniques include methods from Topological Data Analysis, Dynamic Graph Analysis, Applied Algebraic Geometry, Probability Theory, and Game Theory. Some of these methods include tools adapted to the study of dynamic metric spaces, such as zigzag persistent homology and their higher parameter analogs. We find that several of these methods target desired engineering outcomes such as discovery and automatic sub-netting. While each approach is theoretical, they are also algorithmic in nature and offer immediate practical applications. The paper concludes with comparisons of the various methods along with suggestions for future work.

Delay tolerant networking↗
NASA NTRS1975

Dynamic substructure analysis of the International Ultraviolet Explorer (IUE) spacecraft

The results are presented of a steady state vibration analysis of the IUE spacecraft simulating its sinusoidal vibration test. The model of the spacecraft, including solar arrays and the scientific instrument, consisted of three separate substructure models one of which was used to represent the two identical solar arrays. Substructuring techniques were used since the large overall size of the problem precluded solving it utilizing a single model. The models used for each substructure are discussed, including reduction to an acceptable size for the combined dynamic analysis. The DMAP alters needed for performing the modal analysis and the subsequent modal frequency response and substructure data recovery are included. Comparison of the results with data obtained during vibration tests of the spacecraft are also included.

Case, W. R.↗
NASA NTRS1986

Dynamic posture analysis of Spacelab-1 crew members

Dynamic posture testing was conducted on the science crew of the Spacelab-1 mission on a single axis linear motion platform. Tests took place in pre- and post-flight sessions lasting approximately 20 min each. The pre-flight tests were widely spaced over the several months prior to the mission while the post-flight tests were conducted over the first, second, fourth, and sixth days after landing. Two of the crew members were also tested on the day of landing. Consistent with previous postural testing conducted on flight crews, these crew members were able to complete simple postural tasks to an acceptable level even in the first few hours after landing. Our tests were designed to induce dynamic postural responses using a variety of stimuli and from these responses, evaluate subtle changes in the postural control system which had occurred over the duration of the flight. Periodic sampling post-flight allowed us to observe the time course of readaptation to terrestrial life. Our observations of hip and shoulder position, when subjected to careful analysis, indicated modification of the postural response from pre- to post-flight and that demonstrable adjustments in the dynamic control of their postural systems were taking place in the first few days after flight. For transient stimuli where the platform on which they were asked to stand quickly moved a few centimeters fore or aft then stopped, ballistic or open loop 'programs' would closely characterize the response. During these responses the desired target position was not always achieved and of equal importance not always properly corrected some 15 seconds after the platform ceased to move. The persistent observation was that the subjects had a much stronger dependence on visual stabilization post-flight than pre-flight. This was best illustrated by a slow or only partial recovery to an upward posture after a transient base-of-support movement with eyes open. Postural responses to persistent wideband pseudorandom base-of-support translation were modeled as time invarient linear systems arrived at by Kalman adaptive filter techniques. Derived model parameters such as damping factor and fundamental frequency of the closed loop system showed significant modification between pre- and post-flight. This phenomenon is best characterized by movement of the poles toward increasing stability. While pre-flight data tended to show shoulders and hips moving in phase with each other, post-flight data showed a more disjoint behavior.(ABSTRACT TRUNCATED AT 400 WORDS).

Non-NASA Center↗
NASA NTRS1992

Sensitivity analysis of dynamic aeroelastic responses

This paper summarizes ongoing research on the sensitivity analysis of dynamic aeroelastic response of wings. Two approaches are being used to express the unsteady aerodynamic loads: (1) the frequency-domain approach, and (2) the state-space approach. The frequency-domain approach is demonstrated on a three-dimensional box wing and the state-space domain approach is demonstrated on a simple two-dimensional sectional model. Three different methods are used to find the sensitivities: (1) a purely finite difference approach, (2) a semi-analytical approach in which an analytical expression is used for calculating the sensitivity of an eigenvalue of the complex valued aeroelastic matrix, however, the derivatives of the components of the matrix are obtained using finite difference, and (3) a semi-analytic approach that differs from (2) in the sense that the sensitivity of the aerodynamic matrix is now obtained analytically. A good agreement is seen between the three sets of results. For the two-dimensional sectional model the results for the sensitivities of the flutter speed with respect to the various parameters are obtained.

Kapania, Rakesh K.↗
NASA NTRS1988

The analysis of non-linear dynamic behavior (including snap-through) of postbuckled plates by simple analytical solution

Static postbuckling and nonlinear dynamic analysis of plates are usually accomplished by multimode analyses, although the methods are complicated and do not give straightforward understanding of the nonlinear behavior. Assuming single-mode transverse displacement, a simple formula is derived for the transverse load displacement relationship of a plate under in-plane compression. The formula is used to derive a simple analytical expression for the static postbuckling displacement and nonlinear dynamic responses of postbuckled plates under sinusoidal or random excitation. Regions with softening and hardening spring behavior are identified. Also, the highly nonlinear motion of snap-through and its effects on the overall dynamic response can be easily interpreted using the single-mode formula. Theoretical results are compared with experimental results obtained using a buckled aluminum panel, using discrete frequency and broadband point excitation. Some important effects of the snap-through motion on the dynamic response of the postbuckled plates are found.

Ng, C. F.↗
NASA NTRS1973

Insulation commonality assessment (phase 1). Volume 2: Section 7.0 through 16.0

The heat transfer characteristics of various materials used for the thermal insulation of spacecraft are discussed. Techniques for conducting thermal performance analysis, structural performance analysis, and dynamic analysis are described. Processes for producing and finishing the materials are explained. The methods for determining reliability, system safety, materials tests, and design effectiveness are explained.

Source record↗
NASA NTRS1974

Geometric stiffness characteristics of a rotating elastic appendage

Previous work by Likins (1972 and 1973) on finite element appendage equations for hybrid coordinate dynamic analysis and on the dynamic analysis of a system of hinge-connected rigid bodies with nonrigid appendages is extended to the establishment of a basis for a generic digital computer program to be developed for the simulation of nonrigid spacecraft. A subtle but significant generalization of that previous work as well as a correction and elaboration accomplish this purpose.

Likins, P. W.↗
NASA NTRS1983

An Evaluation of Techroll Seal Flexible Joint Material

This study evaluated the materials utilized in the flexible joint for possible failure modes. Studies undertaken included effect of temperature on the strength of the system, effect of fatigue on the strength of the system, thermogravimetric analysis, thermochemical analysis, differential scanning calorimeter analysis, dynamic mechanical analysis, and peel test. These studies indicate that if the joint failed due to a materials deficiency, the most likely mode was excessive temperature in the joint. In addition, the joint material is susceptible to fatigue damage which could have been a contributing factor.

Hall, W. B.↗
NASA NTRS1984

Materials testing of the IUS techroll seal material

As a part of the investigation of the control system failure Inertial Upper Stage on IUS-1 flight to position a Tracking and Data Relay Satellite (TDRS) in geosynchronous orbit, the materials utilized in the techroll seal are evaluated for possible failure models. Studies undertaken included effect of temperature on the strength of the system, effect of fatigue on the strength of the system, thermogravimetric analysis, thermomechanical analysis, differential scanning calorimeter analysis, dynamic mechanical analysis, and peel test. The most likely failure mode is excessive temperature in the seal. In addition, the seal material is susceptible to fatigue damage which could be a contributing factor.

Nichols, R. L.↗