Conversion of Plastic Work into Heat in Dynamic Tensile Loading of 304L-VAR Stainless-Steel
Explore the source record for details and available documents.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
Electric vehicles offer much higher well-to-wheel efficiency than gasoline vehicles and can significantly reduce U.S. dependence on foreign oil, lower greenhouse gas emissions, improve local air quality, and support continued technological and economic growth. Despite these advantages, widespread adoption remains constrained by limitations in current battery technology, including high cost, limited driving range, and long charging times. One promising approach to address these challenges is to reduce onboard energy storage and instead deliver power wirelessly to vehicles while they are at a traffic stop or in motion.
Explore the source record for details and available documents.
The design of a previously developed basic variable R load simulator was entended to increase its power dissipation and transient handling capabilities. The delivered units satisfy all design requirements, and provides for a high power, modular simulation capability uniquely suited to the simulation of complex load responses. In addition to presenting conclusions and recommendations and pertinent background information, the report covers program accomplishments; describes the simulator basic circuits, transfer characteristic, protective features, assembly, and specifications; indicates the results of simulator evaluation, including burn-in and acceptance testing; provides acceptance test data; and summarizes the monthly progress reports.
Present analytical techniques by which design loads are predicted are very costly and time consuming. Chapter I presents the standard techniques used to analyze payload/booster systems. They are full scale methods in the sense that they all require the solution of the coupled equations of motion of the payload/booster system. Chapter II identifies several short cut methodologies. These already existing techniques do not require the solution of the coupled system equations. The potentials and shortcomings of each of these methods are discussed. Chapter III covers the favored methods accompanied by recommendations for further development, refinement, and demonstrations. An outline of a new approach is also included.
The development of a full scale payload integration method which reduces the cost of a load cycle and is capable of land long very large systems is discussed. The method solves the coupled booster/payload system equations and does not involve additional approximations as compared to the standard transient analysis. The method is cost effective and directly applicable to the shuttle payload design case.
Methods for the prediction of loads on large space structures are discussed. Existing approaches to the problem of loads calculation are surveyed. A full scale version of an alternate numerical integration technique to solve the response part of a load cycle is presented, and a set of short cut versions of the algorithm developed. The implementation of these techniques using the software package developed is discussed.
This User Guide with an overview of an integration scheme to determine the response of a launch vehicle with multiple payloads. Chapter II discusses the software package associated with the integration scheme together with several sample problems. A short cut version of the integration technique is also discussed. The Guide concludes with a list of references and the listings of the subroutines.
The Rotor Systems Research Aircraft uses load cells to isolate the rotor/transmission systm from the fuselage. A mathematical model relating applied rotor loads and inertial loads of the rotor/transmission system to the load cell response is required to allow the load cells to be used to estimate rotor loads from flight data. Such a model is derived analytically by applying a force and moment balance to the isolated rotor/transmission system. The model is tested by comparing its estimated values of applied rotor loads with measured values obtained from a ground based shake test. Discrepancies in the comparison are used to isolate sources of unmodeled external loads. Once the structure of the mathematical model has been validated by comparison with experimental data, the parameters must be identified. Since the parameters may vary with flight condition it is desirable to identify the parameters directly from the flight data. A Maximum Likelihood identification algorithm is derived for this purpose and tested using a computer simulation of load cell data. The identification is found to converge within 10 samples. The rapid convergence facilitates tracking of time varying parameters of the load cell model in flight.
Explore the source record for details and available documents.
Heuristics which use predicted process resource requirements to make scheduling decisions are proposed. Four heuristics are presented. The first two, MINQ and SMPL, employ centralized scheduling and the remaining two, DMINQ and FDMINQ, use distributed scheduling. These heuristics are first compared against random scheduling and then against two conventional heuristics, CENTEX and DISTED, which schedule processes solely based on system state information. Results based on trace-driven simulations show that the proposed centralized heuristics offer significantly improved mean response time and they require fewer status update messages. In experiments using the same status update rates, SMPL response times were, on the average, 22 percent lower than those for CENTEX; MINQ response times were, on the average, 18 percent lower. The simulations also showed that MINQ and SMPL can perform as well as, or better than, CENTEX while using up to 70 percent fewer status update messages. The use of fewer status update messages imposes less overhead on the system. The use of prediction for distributed scheduling produced similar results. When prediction was used to filter small processes and execute them locally a 50 percent improvement in response times was obtained.
A technique for calculating the effects of on-orbit loads on the structural dynamics of the International Space Station is developed on the basis of MSC/NASTRAN superelement solution sequences. The complexity of the Space Station program with its multiple configurations, international partners, and contractors is stressed, and the impact of this complexity on the dynamic-load analysis process is indicated. The MSC/NASTRAN-based approach is outlined, and its application to two versions of the Permanent Manned Capability configuration is described in detail, including component mode synthesis, GFSC/FLAME coupled-loads analysis (with components from the system FEM model or from the Work Package), and ISI/MATRIX-X generation of closed-loop forcing functions. The results of these sample analyses are presented in extensive tables and graphs and briefly characterized.
Explore the source record for details and available documents.
An analysis is given of the causes of the increase in the creep of a material under dynamic loads. A theory of dynamic creep is proposed based on the after-effect theory of Becker.
No abstract available
Explore the source record for details and available documents.
Abstract Not Provided
Transient events cause high loads in the drivetrain components so measuring and calculating these loads can improve confidence in drivetrain design. This paper studies the Gearbox Reliability Collaborative 750kW wind turbine gearbox response during transient events using a combined experimental and modeling approach. The transient events include emergency shut-downs and start-ups measured during a field testing period in 2009. The drivetrain model is established in the multibody simulation tool Simpack. A detailed study of modeling fidelity required for accurate load prediction is performed and results are compared against measured loads. A high fidelity model that includes shaft and housing flexibility and accurate bearing stiffnesses is important for the higher-speed stage bearing loads. Each of the transient events has different modeling requirements.