Search NASA⌕ Search

SEARCH · Search NASA

Results for “flaps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Contributions to the theory of side edge flap noise

High and low frequency asymptotic formulas are derived which express the acoustic frequency spectrum in terms of the wavenumber-frequency spectrum of surface pressure fluctuations on the upper surface of a part span flap, measured in-board of the side edge. Interpolations between the results are used to predict the field shape and its dependence on the subsonic forward flight speed over the whole frequency range. The radiation has the characteristics of a semibaffled dipole at small values of the Strouhal number based on the chord of the flap and the forward flight speed. The degree of Doppler amplification due to forward flight speed of the aircraft is dependent on the Strouhal number; the radiation efficiency of side-edge noise sources is governed by the value of the mean side-edge gap Strouhal number, and is larger when this number is small. Theoretical predictions extrapolated to full scale suggest that the noise generated at a single side edge can exceed that generated along the whole of the trailing edge of the flap by 3 dB.

Howe, M. S.↗
NASA NTRS1974

Low-speed aerodynamic characteristics of a 42 deg swept high-wing model having a double-slotted flap system and a supercritical airfoil

A low-speed investigation was conducted over an angle-of-attack range from about -4 deg to 20 deg in the Langley V/STOL tunnel to determine the effects of a double-slotted flap, high-lift system on the aerodynamic characteristics of a 42 deg swept high-wing model having a supercritical airfoil. The wing had an aspect ratio of 6.78 and a taper ratio of 0.36; the double-slotted flap consisted of a 35-percent-chord flap with a 15-percent-chord vane. The model was tested with a 15-percent-chord leading-edge slat.

Fournier, P. G.↗
NASA NTRS1984

Low-speed investigation of effects of wing leading- and trailing-edge flap deflections and canard incidence on a fighter configuration equipped with a forward-swept wing

An advanced fighter configuration with a forward-swept wing of aspect ratio 3.28 is tested in the Langley 7 by 10 Foot High Speed Tunnel at a Mach number of 0.3. The wing has 29.5 degrees of forward sweep of the quarter chord line and is equipped with 15 percent chord leading edge and 30 percent chord trailing edge flaps. The canard is sweptback 45 degrees. Tests were made through a range of angle of attack from about -2 degrees to 22 degrees. Deflecting the flaps significantly improves the lift drag characteristics at the higher angles of attack. The canard is able to trim the configurations with different flap deflections over most of the range of angle of attack. The penalty in maximum lift coefficient due to trimming is about 0.10.

Gainer, T. G.↗
NASA NTRS1984

Flap-lag damping of an elastic rotor blade with torsion and dynamic inflow in hover from symbolically generated equations

A program written in FORTRAN IV and coded into subroutines for subsequent numerical study is used to derive symbolically the governing equations of motion of the elastic rotor blade and the dynamic inflow equations. By rearranging the coefficients of the equations, the blade and dynamic inflow equations are converted into equations in a multiblade coordinated system. The final multiblade equations can accommodate any number of elastic blade modes. It is noted that with a given data set, the entire process, from the derivation of the equations to the numerical calculations, is computerized and requires only limited user interface. To demonstrate the usefulness of the approach, damping data in hover with and without dynamic inflow effects are presented for various rotor blade models, including flap-lag, flap-lag-torsion, quasi-static torsion, and rigid blade lag-flap.

Reddy, T. S. R.↗
NASA NTRS1982

Application of an aerodynamic analysis method including attainable thrust estimates to low speed leading-edge flap design for supersonic cruise vehicles

A study of low speed leading-edge flap design for supersonic cruise vehicle was conducted. Wings with flaps were analyzed with the aid of a newly developed subsonic wing program which provides estimates of attainable leading-edge thrust. Results indicate that the thrust actually attainable can have a significant influence on the design and that the resultant flaps can be smaller and simpler than those resulting from more conventional approaches.

Carlson, H. W.↗
NASA NTRS1983

Additional flow field studies of the GA(W)-1 airfoil with 30-percent chord Fowler flap including slot-gap variations and cove shape modifications

Experimental measurements were made to determine the effects of slot gap opening and flap cove shape on flap and airfoil flow fields. Test model was the GA(W)-1 airfoil with 0.30c Fowler flap deflected 35 degrees. Tests were conducted with optimum, wide and narrow gaps, and with three cove shapes. Three test angles were selected, corresponding to pre-stall and post-stall conditions. Reynolds number was 2,200,000 and Mach number was 0.13. Force, surface pressure, total pressure, and split-film turbulence measurements were made. Results were compared with theory for those parameters for which theoretical values were available.

Wentz, W. H., Jr.↗
NASA NTRS1984

Experimental Results for a Flapped Natural-laminar-flow Airfoil with High Lift/drag Ratio

Experimental results have been obtained for a flapped natural-laminar-flow airfoil, NLF(1)-0414F, in the Langley Low-Turbulence Pressure Tunnel. The tests were conducted over a Mach number range from 0.05 to 0.40 and a chord Reynolds number range from about 3.0 x 10(6) to 22.0 x 10(6). The airfoil was designed for 0.70 chord laminar flow on both surfaces at a lift coefficient of 0.40, a Reynolds number of 10.0 x 10(6), and a Mach number of 0.40. A 0.125 chord simple flap was incorporated in the design to increase the low-drag, lift-coefficient range. Results were also obtained for a 0.20 chord split-flap deflected 60 deg.

Mcghee, R. J.↗
NASA NTRS1984

The performance evaluation of a jet flap on an advanced supersonic harrier

The performance concept of a supersonic vertical and short takeoff and landing (V/STOL) fighter, model 279-3, modified to utilize a jet flap was evaluated. Replacing the rear nozzles of the 279-3 with the jet flap favorably alters the pressure distribution over the airfoil and dramatically increases lift. The result is a significant decrease in takeoff distance, an increase in payload, and an improvement in combat performance. To investigate the benefit in increased payload, the 279-3 and the jet flapped 279-3JF were modeled on the NASA Aircraft Synthesis (ACSYNT) computer code and flown on a 250 feet takeoff distance interdiction mission. The increase in payload weight that the 279-3JF could carry was converted into fuel in one case, and in another, converted to bomb load. When the fuel was increased, the 279-3JF penetrated into enemy territory almost four times the distance of 279-3, and therefore increased mission capability. When the bomb load was increased, the 279-3JF carried 14 bombs the same distance the 279-3 carried four. The increase in mission performance and improvements in turning rates was realized with only a small penalty in increased empty weight.

Lipera, L. D.↗
NASA NTRS1987

Spanwise pressure distribution on delta wing with leading-edge vortex flap

The aerodynamic characteristics of a highly swept planar delta wing employing conical leading edge flaps are numerically investigated, using a free vortex sheet method that is based on an advanced, three-dimensional inviscid flow panel method employing quadratic doublet distributions to represent the wing surface and the rolled-up vortex sheet and wake. Upward flap deflection shifts the negative pressure peak inboard of the basic wing and develops a significant suction pressure on the flap that then produces thrust component in the direction of flight; overall drag is thereby reduced.

Reddy, C. S.↗
NASA NTRS1988

A low speed wind tunnel investigation of Reynolds number effects on a 60-deg swept wing configuration with leading and trailing edge flaps

A low-speed wind tunnel test was performed to investigate Reynolds number effects on the aerodynamic characteristics of a supersonic cruise wing concept model with a 60-deg swept wing incorporating leading-edge and trailing-edge flap deflections. The Reynolds number ranged from 0.3 to 1.6 x 10 to the 6th, and corresponding Mach numbers from .05 to 0.3. The objective was to define a threshold Reynolds number above which the flap aerodynamics basically remained unchanged, and also to generate a data base useful for validating theoretical predictions for the Reynolds number effects on flap performance. This report documents the test procedures used and the basic data acquired in the investigation.

Rao, Dhanvada M.↗
NASA NTRS1988

Turbulent separated flow in the vicinity of a single-slotted airfoil flap

Detailed measurements of pressure and velocity characteristics are presented and analyzed for flow over and downstream of a NACA 4412 airfoil equipped with a NACA 4415 single-slotted flap at high angle of attack and close to maximum lift. The flow remained attached over the main element while a large region of recirculating flow occurred over the aft 61 percent of the flap. The airfoil configuration was tested at a Mach number of 0.09 and chord based Reynolds number of 1.8 x 10 to the 6th in the NASA Ames Research Center 7- by 10-Foot Wind Tunnel. Measurements of mean and fluctuating velocities were obtained in the region of recirculation and high turbulence intensity using three-dimensional laser velocimetry. In regions where the flow had a preferred direction and relatively low turbulence intensity hot-wire anemometry was used. Emphasis was placed on obtaining flow characteristics in the confluent boundary layer, the region of recirculating flow and in the downstream wake. Surface pressure measurements were made on the main airfoil, flap, wind tunnel roof, and wind tunnel floor. In addition to the presentation of pressure and velocity characteristics, the near wall results inside the separated region are analyzed as are the relative importance of terms in the momentum and turbulence kinetic energy equations in the confluent separated boundary layer and the recirculating region of the near wake.

Adair, Desmond↗
NASA NTRS1989

Flap-lag stability data for a small-scale isolated hingeless rotor in forward flight

An isolated, hingeless rotor with discrete flap and lead-lag flexures and relatively rigid blades was tested in the Aeroflightdynamics Directorate's 7- by 10-Foot Wind Tunnel. The lead-lag stability of a structurally simple rotor configuration in forward flight was determined. The model tested had no cyclic pitch control, and was therefore operated untrimmed at several collective pitch angles, at shaft angles from 0 deg to -20 deg, and at advance ratios as high as 0.55. Two inplane natural frequencies, 0.61/rev and 0.72/rev, were tested for configuration both with and without structural flap lag coupling. Concomitant hover testing of the model was also conducted. Representative plots of the frequency and damping data are presented to show general trends, and complete tabular data and model properties information are included for use in detailed correlation exercises. The most prominent feature of the forward flight data is an abrupt increase in damping with advance ratio at certain high-speed, high shaft-angle conditions, with high flapping loads. The hover data are consistent with previous experimental and theoretical results for hingeless rotors without kinematic couplings. Overall, the data quality is very good and the data are expected to be useful in the development and validation of rotor aeroelastic stability analyses.

Mcnulty, Michael J.↗
NASA NTRS1987

An experimental and analytical investigation of stall effects on flap-lag stability in forward flight

Experiments have been performed with a 1.62 m diameter hingeless rotor in a wind tunnel to investigate flap-lag stability of isolated rotors in forward flight. The three-bladed rotor model closely approaches the simple theoretical concept of a hingeless rotor as a set of rigid, articulated flap-lag blades with offset and spring restrained flap and lag hinges. Lag regressing mode stability data was obtained for advance ratios as high as 0.55 for various combinations of collective pitch and shaft angle. The prediction includes quasi-steady stall effects on rotor trim and Floquet stability analyses. Correlation between data and prediction is presented and is compared with that of an earlier study based on a linear theory without stall effects. While the results with stall effects show marked differences from the linear theory results, the stall theory still falls short of adequate agreement with the experimental data.

Nagabhushanam, J.↗
NASA NTRS1989

Effect of 90 degree flap on the aerodynamics of a two-element airfoil

The aerodynamic performance of a two-element airfoil with a 90-deg trailing edge flap was experimentally investigated. The 5 percent-chord long flap, significantly increased the lift of the baseline airfoil, throughout a wide range of angles of attack. The maximum lift coefficient of the flapped wing increased too, whereas the lift/drag ratio decreased.

Katz, J.↗
NASA NTRS1991

The full-scale process and design changes for elimination of insulation edge separations and voids in tang flap area

Qualification of the full-scale process and design changes for elimination of redesigned solid rocket motor tang nitrile butadiene rubber insulation edge separations and voids was performed from 24 March to 3 December 1990. The objectives of this test were: to qualify design and process changes on flight hardware using a tie ply between the redesigned solid rocket motor steel case and the nitrile butadiene rubber insulation over the tang capture features; to qualify the use of methyl ethyl ketone in the tang flap region to reduce voids; and to determine if holes in the separator film reduce voids in the tang flap region. The tie ply is intended to aid insulation flow during the insulation cure process, and thus reduce or eliminate edge unbonds. Methyl ethyl ketone is intended to reduce voids in the tang flap area by providing better tacking characteristics. The perforated film was intended to provide possible vertical breathe paths to reduce voids in the tang area. Tang tie ply testing consisted of 270 deg of the tang circumference using a new layup method and 90 deg of the tang circumference using the current layup methods. Tie ply process success was defined as a reduction of insulation unbonds. Lack of any insulation edge unbonds on the tang area where the new process was used, and the presence of 17 unbonds with the current process, proves the test to be a success. Successful completion of this test has qualified the new processes.

Danforth, Richard A.↗
NASA NTRS1991

Unsteady supersonic flow around delta wings with symmetric and asymmetric flaps oscillation

A parametric study is presented to investigate the effect of reduced frequency of the leading-edge flaps on the locally-conical, unsteady, supersonic flow around a delta wing. This study covers symmetric and antisymmetric forced oscillation of the leading-edge flaps. The effects of the freestream Mach number and angle of attack are also presented. The problem is solved using time-accurate integration of the unsteady, compressible, thin-layer Navier-Stokes equations and the unsteady, linearized, Navier-displacement equations. The delta wing is of aspect ratio of 1.5 and its leading-edge flaps are hinged at 65 percent of the local-half span length. The reduced frequency is varied between 2 pi and pi/2. Two supersonic flow conditions have been investigated; the first is for a freestream Mach number of 2.4 and an angle of attack of 19 deg and the second is for a freestream Mach number of 1.5 and an angle attack of 15 deg.

Kandil, Osama A.↗
NASA NTRS1991

Effects of leading-edge flap oscillation on unsteady delta wing flow and rock control

The isolated and interdisciplinary problems of unsteady fluid dynamics and rigid-body dynamics and control of delta wings with and without leading-edge flap oscillation are considered. For the fluid dynamics problem, the unsteady, compressible, thin-layer Navier-Stokes (NS) equations, which are written relative to a moving frame of reference, are solved along with the unsteady, linearized, Navier-displacement (ND) equations. The NS equations are solved for the flowfield using an implicit finite-volume scheme. The ND equations are solved for the grid deformation, if the leading-edge flaps oscillate, using an ADI scheme. For the dynamics and control problem, the Euler equation of rigid-body rolling motion for a wing and its flaps are solved interactively with the fluid dynamics equations for the wing-rock motion and subsequently for its control. A four-stage Runge-Kutta scheme is used to explicitly integrate the dynamics equation.

Kandil, Osama A.↗
NASA NTRS1991

Calculation of unsteady airfoil loads with and without flap deflection at -90 degrees incidence

A method has been developed for calculating the viscous flow about airfoils with and without deflected flaps at -90 deg incidence. This unique method provides for the direct solution of the incompressible Navier-Stokes equations by means of a fully coupled implicit technique. The solution is calculated on a body-fitted computational mesh incorporating a staggered grid method. The vorticity is determined at the node points, and the velocity components are defined at the mesh-cell sides. The staggered-grid orientation provides for accurate representation of vorticity at the node points and for the conservation of mass at the mesh-cell centers. The method provides for the direct solution of the flow field and satisfies the conservation of mass to machine zero at each time-step. The results of the present analysis and experimental results obtained for a XV-15 airfoil are compared. The comparisons indicate that the calculated drag reduction caused by flap deflection and the calculated average surface pressure are in excellent agreement with the measured results. Comparisons of the numerical results of the present method for several airfoils demonstrate the significant influence of airfoil curvature and flap deflection on the predicted download.

Stremel, Paul M.↗