Search NASA⌕ Search

SEARCH · Search NASA

Results for “materials research”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Vapor Growth of ZnSe-based Compound Semiconductors in Low Gravity environment on International Space Station

Six low-gravity experiments of crystal growth of ZnSe-based compound semiconductors by physical vapor transport (PVT) are scheduled to be processed inside Low Gradient Furnace (LGF) on Materials Science Research Rack (MSRR) in Material Science Laboratory (MSL) on International Space Station (ISS) starting from February 27th, 2023. The flight samples consist of three unseeded growths of ZnSe, Cr-doped ZnSe and ZnSeTe as well as growth of ZnSe on top of three single crystal ZnSe seeds with orientation of (100), (110) and (111). The main scientific objective of the flight experiments is to establish the effects of gravity-driven fluid flows on Earth to (i) the non-uniform incorporation of impurities and defects and (ii) the deviation from stoichiometry observed in the grown crystals caused by growth interface fluctuations and evolution as the results of buoyancy-driven convection and irregular fluid-flows. The investigation will also evaluate the effects of gravity on the PVT process by examining (i) the growth kinetics on various seed orientations, (ii) the dopant segregation and distribution in the Cr doped ZnSe, and (iii) the compositional segregation and distribution in the ternary ZnSeTe crystal grown by PVT. Additionally, from X-ray diffraction/topography and by measuring the density and distribution of various crystalline defects it will assess the self-induced strain effects developed during processing at elevated temperatures caused by the weight of the crystals. During the ground-based preparations, the following tasks have been accomplished: • Establish the thermodynamic properties of the ZnSe binary and related ternary systems by measuring the partial pressures of the vapor phase coexisting with the condensed phases and perform phase diagram calculations for comparison. • Evaluate the effects of gravity-driven convection in the growth process by performing experiments under various vapor transport orientations relative to gravity vector, i.e., horizontal, vertically stabilized and destabilized configurations. • Establish a quantitative correlation between growth parameters and the characteristics and properties of the grown crystals by characterizing the crystals using a variety of techniques. • Evaluate the fundamentals of the current theories on vapor transport and crystal growth kinetics by performing in-situ and real-time monitoring techniques during growth. • Develop a one-dimensional diffusion limited theory of mass transport and two- and three-dimensional numerical simulations of both mass transport and heat transfer and thus establish the microgravity requirements for the flight experiments and to predict the characteristics of the grown crystals such as the solid-vapor interface shapes… etc. and establish a fundamental understanding of the crystal growth process from the comparison with experimental results.

ZnSe↗
NASA NTRS1982

Tribological properties of amorphous alloys and the role of surfaces in abrasive wear of materials

The research approach undertaken by the authors relative to the subject, and examples of results from the authors are reviewed. The studies include programs in adhesion, friction, and various wear mechanisms (adhesive and abrasive wear). The materials which have been studied include such ceramic and metallic materials as silicon carbide, ferrites, diamond, and amorphous alloys.

Miyoshi, K.↗
NASA NTRS2001

A Study of Failure Criteria of Fibrous Composite Materials

The research described in this paper is focused on two areas: (1) evaluation of existing composite failure criteria in the nonlinear, explicit transient dynamic finite element code, MSC.Dytran, and (2) exploration of the possibilities for modification of material and failure models to account for large deformations, progressive failure, and interaction of damage accumulation with stress/strain response of laminated composites. Following a review of the MSC.Dytran user manual, a bibliographical review of existing failure criteria of composites was performed. The papers considered most interesting for the objective of this report are discussed in section 2. The failure criteria included in the code under consideration are discussed in section 3. A critical summary of the present procedures to perform analysis and design of composites is presented in section 4. A study of the most important historical failure criteria for fibrous composite materials and some of the more recent modifications proposed were studied. The result of this analysis highlighted inadequacies in the existing failure criteria and the need to perform some numerical analyses to elucidate the answer to questions on which some of the proposed criteria are based. A summary of these ideas, which is a proposal of studies to be developed, is presented in section 5. Finally, some ideas for future developments are summarized in section 6.

Paris, Federico↗
NASA NTRS1976

NASA research on structures and materials for supersonic cruise aircraft

The technology and data base necessary for sound technical decisions regarding long haul supersonic cruise aircraft transportation systems are considered. The objectives and status of the research elements in the structures and materials program phase of the program are reviewed. Emphasis is placed on reductions in structural mass by research on advanced structural concepts, light-weight materials, improved loads, aeroelastic predictive techniques, and by development of efficient structural design procedures.

Cooper, P. A.↗
NASA NTRSDate not supplied

Vertical Motion Simulator -- A Unique Facility for Piloted GNC Research

This material is for presentation at the annual meeting of the NASA Engineering and Safety Center (NESC) Guidance, Navigation, and Control (GNC) Technical Discipline Team (TDT), on 22 July 2020. The briefing is entitled “Vertical Motion Simulator – A Unique Facility for Piloted GNC Research.” It provides a technical description of key VMS features and a high-level overview of some large bodies of work conducted in the VMS over the past 40 years.

Vertical Motion Simulator↗
NASA NTRS2009

Oxygen Compatibility of Brass-Filled PTFE Compared to Commonly Used Fluorinated Polymers for Oxygen Systems

Safe and reliable seal materials for high-pressure oxygen systems sometimes appear to be extinct species when sought out by oxygen systems designers. Materials that seal well are easy to find, but these materials are typically incompatible with oxygen, especially in cryogenic liquid form. This incompatibility can result in seals that leak, or much worse, seals that easily ignite and burn during use. Materials that are compatible with oxygen are easy to find, such as the long list of compatible metals, but these metallic materials are limiting as seal materials. A material that seals well and is oxygen compatible has been the big game in the designer's safari. Scientists at the Materials Combustion Research Facility (MCRF), part of NASA/Marshall Space Flight Center (MSFC), are constantly searching for better materials and processes to improve the safety of oxygen systems. One focus of this effort is improving the characteristics of polymers used in the presence of an oxygen enriched environment. Very few systems can be built which contain no polymeric materials; therefore, materials which have good impact resistance, low heat of combustion, high auto-ignition temperature and that maintain good mechanical properties are essential. The scientists and engineers at the Materials Combustion Research Facility, in cooperation with seal suppliers, are currently testing a new formulation of polytetrafluoroethylene (PTFE) with Brass filler. This Brass-filled PTFE is showing great promise as a seal and seat material for high pressure oxygen systems. Early research has demonstrated very encouraging results, which could rank this material as one of the best fluorinated polymers ever tested. This paper will compare the data obtained for Brass-filled PTFE with other fluorinated polymers, such as TFE-Teflon (PTFE) , Kel-F 81, Viton A, Viton A-500, Fluorel , and Algoflon . A similar metal filled fluorinated polymer, Salox-M , was tested in comparison to Brass-filled PTFE to demonstrate the importance of the metal chosen and relative percentage of filler. General conclusions on the oxygen compatibility of this formulation are drawn, with an emphasis on comparing and contrasting the materials performance to the performance of the current state-of-the-art oxygen compatible polymers.

Herald, Stephen D.↗
NASA NTRS1982

Process research on non-CZ silicon material

High risk, high payoff research areas associated with he process for producing photovoltaic modules using non-CZ sheet material are investigated. All investigations are being performed using dendritic web silicon, but all processes are directly applicable to other ribbon forms of sheet material. The technical feasibility of forming front and back junctions in non-CZ silicon using liquid dopant techniques was determined. Numerous commercially available liquid phosphorus and boron dopant solutions are investigated. Temperature-time profiles to achieve N(+) and P(+) sheet resistivities of 60 + or - 10 and 40 + or - s10 ohms per square centimeter respectively are established. A study of the optimal method of liquid dopant application is performed. The technical feasibility of forming a liquid applied diffusion mask to replace the more costly chemical vapor deposited SiO2 diffusion mask was also determined.

Source record↗
NASA NTRS1983

Process research of non-CZ silicon material

High risk, high payoff research areas associated with the Westinghouse process for producing photovoltaic modules using non- CZ sheet material were investigated. All work was performed using dendritic web silicon. The following tasks are discussed and associated technical results are given: (1) determining the technical feasibility of forming front and back junctions in non-CT silicon using dopant techniques; (2) determining the feasibility of forming a liquid applied diffusion mask to replace the more costly chemical vapor deposited SiO2 diffusion mask; (3) determining the feasibility of applying liquid anti-reflective solutions using meniscus coating equipment; (4) studying the production of uniform, high efficiency solar cells using ion implanation junction formation techniques; and (5) quantifying cost improvements associated with process improvements.

Source record↗
NASA NTRSDate not supplied

A Historical Overview of the NASA Orbital Debris Program Office’s Laboratory Optical Measurements

The NASA Orbital Debris Program Office (ODPO) has used laboratory measurements to help bring ground-based measurements together with models to ascertain Earth-orbiting target parameters of interest to support various orbital debris models. In 2005, the Optical Measurement Center (OMC) was established to simulate space-based illumination conditions using equipment and techniques that recreate telescopic observations, particularly source-target-sensor orientations. The intent was to recreate light curves using known aspect angles of known targets and phase angles (angle is defined by the vertex between illumination source-object-detector) to complement telescopic observations that could be used to update the current optical size estimation model (OSEM) – a model that converts object brightness into size for orbital debris models. To support the above goals, the laboratory has undergone several equipment upgrades to increase capabilities over almost 20 years of operation. The primary instrumentation acquires reflectance measurements and includes a solar-like light source, CCD camera with astrometric filters, and robotic arm. A rotary arm was added approximately five years after full operation to allow acquisition through a full 360° range of phase angles. Another part of the OMC instrumentation is a field spectrometer, predominately used for field operations to acquire pre- and post-flight spacecraft material spectral measurements. Additionally, reflectance spectroscopy of various materials is also of interest resulting from hypervelocity impact tests, pristine spacecraft materials, or samples of materials that are used in spacecraft design. These measurements are stored in NASA’s Spectral Material Database, a resource that is still being populated today. The study of spectral measurements also enabled the development of spectral unmixing routines to support the identification of spacecraft materials from spectral data gathered by ground based telescopes. Preliminary OMC investigations focused on feasibility studies to acquire 360° rotation light curves of simple shapes at a single-phase angle and extended to measurements of representative fragments from ground-based explosion tests. To correlate the light curves with ground-based optical measurements, a focused study on high area to mass materials was conducted in support of a newly identified population (at the time) in geosynchronous orbit (GEO) consisting of multi-layered insulation. To further characterize orbital debris, a larger selection of materials was analyzed using laboratory photometric measurements that included representative targets from pristine spacecraft materials and ground-based impact tests. Around 2012, an initiative was requested to understand the feasibility of active debris removal (ADR) of larger targets using grappling methods for spent rocket bodies. Using a priori information on selected targets, scaled-down versions of rocket bodies were generated thanks to improvements in 3D printing technology and machining. These targets were studied in the OMC to understand rotation characteristics. These were compared with telescopic data to determine if the tumble and rotation angles would allow ADR. In 2013, the OMC focused on combining spectral measurements with photometric data to characterize GEO orbital debris. Several years later, NASA acquired a Titan III Transtage test article from “The Boneyard” with a high-resemblance to on-orbit Titan III Transtage rocket bodies, allowing physical access to a representative rocket body that suffered fragmentations in GEO. This prompted the creation of 3D models using lidar technology and spectral measurements of the materials. Focused research also transitioned to specific materials (i.e., solar cells) when telescopic surveys requested characterization of specific GEO targets. In the different research products presented, the focus has been to understand the various parameters that influence optical size estimation, including albedo, phase functions, and brightness variations. Work in this area continues with newer sources of data, including DebriSat, a high-fidelity 56-kg spacecraft replica representative of a modern low Earth orbit (LEO) satellite subjected to a laboratory hypervelocity impact test to understand fragmentation events and to support updates to satellite breakup models and size estimation models. Utilizing the vast population of fragments from DebriSat and prior laboratory impact experiments, the ODPO has focused on acquiring bidirectional reflectance distribution function (BRDF) data to characterize targets in the laboratory, thus removing aspect angle dependencies. Additionally, the DebriSat project has provided improved processes for measuring size via image acquisition, such that a true fragment size can be directly compared to the derived size using the OSEM. The team continues to assess BRDFs and use spectral measurement data to investigate the parameters used in the OSEM, specifically magnitudes, albedo, and phase functions.

Heather Cowardin↗
NASA NTRS1967

Maser research program

Materials preparation and microwave bench measurements for zero-field traveling wave maser

MICROWAVE FREQUENCY↗
NASA NTRS1971

An investigation of oxidation-resistant solid lubricant materials.

Recent research at NASA-Lewis on solid lubricants for use at high temperatures in air and other gaseous environments is presented. The characteristics of oxide and fluoride lubricants at temperatures to 1700 F are described. Data is presented for fluoride coatings with silicate and other additives incorporated to give improved wear life and better oxidation protection to the substrate metal. Experience is described for fluoride-metal self-lubricating composites with improved metal oxidation resistance to 1700 F. The concept of cast, self-lubricating ceramics is also explored.

Sliney, H. E.↗
NASA NTRS1975

Studies of finite element analysis of composite material structures

Research in the area of finite element analysis is summarized. Topics discussed include finite element analysis of a picture frame shear test, BANSAP (a bandwidth reduction program for SAP IV), FEMESH (a finite element mesh generation program based on isoparametric zones), and finite element analysis of a composite bolted joint specimens.

Douglas, D. O.↗
NASA NTRS1985

Module flammability research

New materials were developed which show promise of fabricating modules that can pass the Underwriter Laboratories Class A burning brand test for fire ratable solar cell modules. It is concluded that fire resistant module design require special high temperature materials and constructions to achieve Class B and Class A ratings. Also, synergisms exist between back surface materials and module configuration.

Sugimura, R. S.↗
NASA NTRS1990

Automated eddy current analysis of materials

This research effort focused on the use of eddy current techniques for characterizing flaws in graphite-based filament-wound cylindrical structures. A major emphasis was on incorporating artificial intelligence techniques into the signal analysis portion of the inspection process. Developing an eddy current scanning system using a commercial robot for inspecting graphite structures (and others) has been a goal in the overall concept and is essential for the final implementation for expert system interpretation. Manual scans, as performed in the preliminary work here, do not provide sufficiently reproducible eddy current signatures to be easily built into a real time expert system. The expert systems approach to eddy current signal analysis requires that a suitable knowledge base exist in which correct decisions as to the nature of the flaw can be performed. In eddy current or any other expert systems used to analyze signals in real time in a production environment, it is important to simplify computational procedures as much as possible. For that reason, we have chosen to use the measured resistance and reactance values for the preliminary aspects of this work. A simple computation, such as phase angle of the signal, is certainly within the real time processing capability of the computer system. In the work described here, there is a balance between physical measurements and finite element calculations of those measurements. The goal is to evolve into the most cost effective procedures for maintaining the correctness of the knowledge base.

Workman, Gary L.↗
NASA NTRS2000

Microgravity Disturbance Characterization of the Quench Module Insert (QMI) Phase Change Device (PCD)

The Materials Science Research Facility (MSRF) is a multi-user, multi-purpose facility for materials science research. One experiment within the MSRF will be the Quench Module Insert (QMI), a high-temperature furnace with unique capabilities for processing different classes of materials. The primary functions of the QMI furnace are to melt, directionally solidify, and quench metallic samples, providing data to aid in understanding the effects of the microgravity environment on the characteristics of these processed metals. The QMI houses sealed individual sample ampoules containing material to be processed. Quenching of the samples in the QMI furnace is accomplished by releasing low-melting-point metallic shoes into contact with the outside of the sample ampoule, dissipating heat and cooling the sample inside. The impact from this method of quench will induce sample vibrations which could be large enough to adversely affect sample quality. Utilizing breadboard hardware, the sample quench sequence, releasing the shoes, was conducted. Data was collected from accelerometers located on the breadboard sample cartridge, indicating the maximum acceleration achieved by the sample. The primary objective of the test described in this presentation was to determine the acceleration imparted on the sample by the shoe contact. From this information, the science community can better assess whether this method of quench will allow them to obtain the data they need.

Gattis, Christy↗
NASA NTRS1987

Materials analysis by ultrasonics: Metals, ceramics, composites

Research results in analytical ultrasonics for characterizing structural materials from metals and ceramics to composites are presented. General topics covered by the conference included: status and advances in analytical ultrasonics for characterizing material microstructures and mechanical properties; status and prospects for ultrasonic measurements of microdamage, degradation, and underlying morphological factors; status and problems in precision measurements of frequency-dependent velocity and attenuation for materials analysis; procedures and requirements for automated, digital signal acquisition, processing, analysis, and interpretation; incentives for analytical ultrasonics in materials research and materials processing, testing, and inspection; and examples of progress in ultrasonics for interrelating microstructure, mechanical properties, and dynamic response.

Vary, Alex↗
NASA NTRS2002

Novel High Efficient Organic Photovoltaic Materials: Final Summary of Research

The objectives and goals of this project were to investigate and develop high efficient, lightweight, and cost effective materials for potential photovoltaic applications, such as solar energy conversion or photo detector devices. Specifically, as described in the original project proposal, the target material to be developed was a block copolymer system containing an electron donating (or p-type) conjugated polymer block coupled to an electron withdrawing (or n-type) conjugated polymer block through a non-conjugated bridge unit. Due to several special requirements of the targeted block copolymer systems, such as electron donating and withdrawing substituents, conjugated block structures, processing requirement, stability requirement, size controllability, phase separation and self ordering requirement, etc., many traditional or commonly used block copolymer synthetic schemes are not suitable for this system. Therefore, the investigation and development of applicable and effective synthetic protocols became the most critical and challenging part of this project. During the entire project period, and despite the lack of a proposed synthetic polymer postdoctoral research associate due to severe shortage of qualified personnel in the field, several important accomplishments were achieved in this project and are briefly listed and elaborated. A more detailed research and experimental data is listed in the Appendix.

Sun, Sam↗
NASA NTRS2019

Evaluation of Cyclo Olefin Polymer as Sabot Material for High-Density Projectiles

Assuring the integrity of spacecraft and its occupants are a priority in the field of space exploration. Micrometeoroids and orbital debris are one of the primary threats that affect spacecraft materials due to the high kinetic energies involved with hypervelocity impacts. Improvement of projectile launching capabilities prompts the investigation of adequate materials for the manufacturing of sabots able to carry high-density projectiles without catastrophic failure. Polycarbonate has been the chosen material by the Hypervelocity Team at White Sands Test Facility for sabots on the 0.50 caliber launcher; however, there is a material constraint when the projectile becomes significantly dense and the inertial stresses surpass the yield strength of the sabot material. This research proposes a new polymer material for manufacturing sabots, known as cyclo olefin polymer (COP) with the purpose of successfully shooting the intended high-density projectiles. In this investigation, both polycarbonate and COP were analyzed using tensile and impact testing to observe the differences in their mechanical properties. The experimental details along with the detailed characterization of the materials are presented.

Tarango, Estebanne↗