Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

New Mechanism for Yield Point Phenomena

Yield point phenomena (YPP) are widely attributed to discrete dislocation locking by solute atmospheres. An alternate YPP mechanism was recently suggested by simulations of Ta single crystals without any influence of solutes or discrete dislocations. The general meso-scale (GM) simulations consist of crystal plasticity (CP) plus accounting for internal stresses of geometrically necessary dislocation content. GM predicted the YPP while CP did not, suggesting a novel internal stress mechanism. The predicted YPP varied with crystal orientation and boundary conditions, contrary to expectations for a solute mechanism. The internal stress mechanism was probed by experimentally deforming oligocrystal Ta samples and comparing the results with independent GM simulations. Strain distributions of the experiments were observed with high-resolution digital image correlation. A YPP stress–strain response occurred in the 0–2% strain range in agreement with GM predictions. Shear bands appeared concurrent with the YPP stress–strain perturbation in agreement with GM predictions. At higher strains, the shear bands grew at progressively slower rates in agreement with GM predictions. It was concluded that the internal stress mechanism can account for the existence of YPP in a wide variety of materials including ones where interstitial-dislocation interactions and dislocation transient avalanches are improbable. Furthermore, the internal stress mechanism is a CP analog of various micro-scale mechanisms of discrete dislocations such as pile-up or bow-out. It may operate concurrently with strain aging, or either mechanism may operate alone. A suggestion was made for a future experiment to answer this question.

42 ENGINEERING↗

First-Principles Calculations, Experimental Study, and Thermodynamic Modeling of the Al-Co-Cr System

The phase relations and thermodynamic properties of the condensed Al-Co-Cr ternary alloy system are investigated using first-principles calculations based on density functional theory (DFT) and phase-equilibria experiments that led to X-ray diffraction (XRD) and electron probe micro-analysis (EPMA) measurements. A thermodynamic description is developed by means of the calculations of phase diagrams (CALPHAD) method using experimental and computational data from the present work and the literature. Emphasis is placed on modeling the bcc-A2, B2, fcc-γ, and tetragonal-σ phases in the temperature range of 1173 to 1623 K. Liquid, bcc-A2 and fcc-γ phases are modeled using substitutional solution descriptions. First-principles special quasirandom structures (SQS) calculations predict a large bcc-A2 (disordered)/B2 (ordered) miscibility gap, in agreement with experiments. A partitioning model is then used for the A2/B2 phase to effectively describe the order-disorder transitions. The critically assessed thermodynamic description describes all phase equilibria data well. A2/B2 transitions are also shown to agree well with previous experimental findings.

36 MATERIALS SCIENCE↗

Addendum to Capability Needs for Irradiated and Radioactive Materials Research (Ad Hoc Committee Summary Report)

Nuclear materials and fuels studies are challenging research and engineering targets because of their inherent radioactivity as well as their heterogeneous microstructure. Advanced light sources have made significant underpinning scientific contributions to the understanding of structural and fuel cladding material microstructure and properties and the development of structure-property relationships. These facilities have the potential to help advance the Department of Energy (DOE) Office of Nuclear Energy (DOE-NE) mission priorities providing underpinning understanding of technically important challenges, including: irradiation induced embrittlement and swelling; stress corrosion cracking and corrosion in extreme environments; ageing of reactor pressure vessels steels; nuclear fuel characterization; and nuclear waste form optimization as well as playing a major role in the development of a materials performance matrix to aid in the design of new materials to meet the needs of advanced reactor concepts. However, the delivery of underpinning understanding is the mission of DOE Office of Science (DOE-SC). While filling such knowledge gaps is important, efforts in this direction should not be confused with the strategic technology focused mission goals of DOE-NE to enable the continued operation of existing U.S. nuclear reactors, to enable the deployment of advanced nuclear reactors, to develop advanced nuclear fuel cycles, and to maintain U.S. leadership in nuclear energy technology.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Failure of Steel Grinding Balls

Abstract—The structure of grinding balls with an atypical central zone is studied after failure in tests. The structure of the corresponding blanks is also analyzed. The appearance of martensitic sections in the central zone is explained. Recommendations are made for eliminating this problem.

42 ENGINEERING↗

High-rate Plastic Deformation of Nanocrystalline Tantalum to Large Strains: Molecular Dynamics Simulation

Recent advances in the ability to generate extremes of pressure and temperature in dynamic experiments and to probe the response of materials has motivated the need for special materials optimized for those conditions as well as a need for a much deeper understanding of the behavior of materials subjected to high pressure and/or temperature. Of particular importance is the understanding of rate effects at the extremely high rates encountered in those experiments, especially with the next generation of laser drives such as at the National Ignition Facility. Here we use large-scale molecular dynamics (MD) simulations of the high-rate deformation of nanocrystalline tantalum to investigate the processes associated with plastic deformation for strains up to 100%. We use initial atomic configurations that were produced through simulations of solidification in the work of Streitz et al [Phys. Rev. Lett. 96, (2006) 225701]. These 3D polycrystalline systems have typical grain sizes of 10-20 nm. We also study a rapidly quenched liquid (amorphous solid) tantalum. We apply a constant volume (isochoric), constant temperature (isothermal) shear deformation over a range of strain rates, and compute the resulting stress-strain curves to large strains for both uniaxial and biaxial compression. We study the rate dependence and identify plastic deformation mechanisms. The identification of the mechanisms is facilitated through a novel technique that computes the local grain orientation, returning it as a quaternion for each atom. This analysis technique is robust and fast, and has been used to compute the orientations on the fly during our parallel MD simulations on supercomputers. We find both dislocation and twinning processes are important, and they interact in the weak strain hardening in these extremely fine-grained microstructures.

36 MATERIALS SCIENCE↗

Correlation of creep rate with microstructural changes during high temperature creep

The techniques of electron microscopy were used to examine the microstructural changes which occur during primary creep for two important types of engineering alloys: (1) alloys strengthened by solid-solution additions, and (2) dispersion-strengthened alloys. The metals chosen for study are unalloyed titanium, Ti-6Al-4V, and the cobalt-base alloy, Haynes 188. Results to date on NGR 47-004-108 show that development of prior dislocation substructure in Haynes 188 by 10% prestrain and annealing for one hour at 1800 F increases the time to reach 0.5% creep strain at 1600 F by more than an order of magnitude for creep stresses from 3 to 20 ksi. For creep at 1800 F, similar results were obtaind for stresses above 7 ksi, but the prior substructure decreases creep resistance below 7 ksi. This effect appears to be related to instability of grain structure at 1800 F in prestrained material.

Young, C. T.↗

Creep-rupture behavior of iron superalloys in high-pressure hydrogen

The creep-rupture properties of five iron-base and one cobalt-base high temperature alloys were investigated to assess the feasibility of using the alloys as construction materials in a Stirling engine. The alloys were heat treated and hardness measurements were taken. Typical microstructures of the alloys are shown. The creep-rupture properties of the alloys were determined at 760 and 815 C in 15.0 MPa H2 for 200 to 1000 hours. Plots of rupture life versus stress for the six superalloys are presented along with creep strain-time plots.

Bhattacharyya, S.↗

An Initial Microstructurally Informed Model of High Burnup Structure Formation in UO 2 Fuel

The microstructure of a UO 2 fuel pellet changes as burnup increases, impacting fuel performance. Predicting and characterizing high burnup structure (HBS) and dark zone formation is a key part of supporting burnup limit extensions for light water reactors. This paper describes a model developed through fitting radially resolved pellet data obtained from recently published microstructural characterization data. The model predicts grain size and grain character, in addition to pore density and size, with fitting dependencies on power history variables. Separately fitting power history variables to microstructural parameters allows for insight into the underlying physical phenomena for future model development. Additionally, experimental data have been correlated to an HBS fraction to facilitate the development of a model capable of predicting a total fuel restructured fraction at the engineering scale. In conclusion, this two-step approach provides a coupling from reactor power history to microstructural data to fractional HBS and creates a basis to model HBS-dependent parameters in a fuel performance code.

High burnup structure↗

Effect of Microstructure on the High Temperature Fatigue Properties of Two Ni-based Superalloys

There is significant need for Ni-based superalloys in the next generation automotive engine components such as exhaust valves. High temperature, high cycle fatigue life is one of the important properties required for such applications. The focus of this work is to evaluate the effect of microstructure on the high cycle fatigue properties of two Ni-based alloys, alloy 751, an alloy used in these applications at lower temperatures, and Waspaloy. High cycle fatigue lives of the alloys at 870oC were evaluated using in-situ high temperature fully reversed fatigue tests at 870oC and a nominal frequency of 30 Hz. Scanning electron microscopy and transmission electron microscopy were used to characterize the microstructure of the alloys. Computational modeling was used to calculate the equilibrium microstructure and microstructural coarsening at 870oC. Correlation of fatigue properties with microstructure of the alloys shows that for the experimental conditions used in the study, the fatigue life of Waspaloy, which has greater high temperature strength and larger volume fraction, is better than that of alloy 751.

Muralidharan, Govindarajan↗

Modeling deformation and failure in AlSi-polyester abradable sealcoating material using microstructure-based finite element simulation

A plasma-sprayed aluminum-silicon (AlSi)/polyester coating is applied in modern gas turbine engines as an abradable sealcoating to maintain tight clearances between the rotating blades and the static casing. While running the engine, the rotating blades “rub” with the abradable coating, which results in extreme strain rate (up to 10 6 ) dynamics and a high-temperature environment. Due to the difficulty of collecting direct measurements, predictive computational models are important for analyzing the deformation and failure of the abradable material, to help meet the design target of avoiding damage to the blade tip and maintaining high fuel efficiency. In this research, a microstructure-based finite element (FE) computational model was developed to capture the complex mechanical behavior of the AlSi/polyester microstructure. The model is based on a virtual representative-volume-element (RVE) of a metal-polymer microstructure, reconstructed from x-ray computed tomography. It models the plastic deformation of, and damage to, each AlSi and polyester constituents, as well as the failure at their interface. The model was calibrated and validated with uniaxial tension and compression experiments, conducted at two temperatures (298 K and 533 K) at an applied strain rate of 10 3 - 10 4 s -1 . The material exhibited strongly asymmetric tension-compression behavior and a sensitivity to temperature, which was well captured by the model. The model was further applied to investigate changes in mechanical behavior due to variations in constituents’ volume fractions, which provides guidance to the microstructural design of AlSi/polyester abradable materials. The model is expected to facilitate the development of improved abradable materials by bypassing the conventional trial-and-error approach and extensive testing requirements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructure Characterization and Modeling for Improved Electrode Design

This presentation summarizes fiscal year 2018-2019 work under U.S. Department of Energy's Computer-Aided Engineering of Batteries (CAEBAT) program to develop computational tools for improved electrode design and to provide deeper fundamental understanding of the physics that limit the performance and cause degradation in lithium-ion batteries. Successes include (1) development of an electrode microstructure characterization tool box to be published open source later in 2019, (2) development of a large deformation electrochemical model capturing the volume expansion and performance limits of electrodes utilizing silicon and (3) development of a solid mechanics damage model describing the fracture of polycrystalline nickel-manganese-cobalt cathode materials with cycling.

30 DIRECT ENERGY CONVERSION↗

Cross-Correlation Analysis of Digital Speckle Photography

This paper describes new algorithms for processing noisy specklograms, which permit quantitative diagnostics of the microstructure of shock-wave flows with a subpicosecond accuracy with the use of statistical analysis of numerically registered speckle fields disturbed by the refraction in the investigated flows. The software developed by us permits reconstructing up to 10,000 vector angles of probe radiation deflection in a two-dimensional region of size 20 × 30 mm{sup 2} in imaging a speckle field with optical magnification M = 1.

42 ENGINEERING↗

Advanced Constituents and Processes for Ceramic Composite Engine Components

The successful replacement of metal alloys by ceramic matrix composites (CMC) in hot-section engine components will depend strongly on optimizing the processes and properties of the CMC microstructural constituents so that they can synergistically provide the total CMC system with improved temperature capability and with the key properties required by the components for long-term structural service. This presentation provides the results of recent activities at NASA aimed at developing advanced silicon carbide (Sic) fiber-reinforced hybrid Sic matrix composite systems that can operate under mechanical loading and oxidizing conditions for hundreds of hours at 2400 and 2600 F, temperatures well above current metal capability. These SiC/SiC composite systems are lightweight (-30% metal density) and, in comparison to monolithic ceramics and carbon fiber-reinforced ceramic composites, are able to reliably retain their structural properties for long times under aggressive engine environments. It is shown that the improved temperature capability of the SiC/SiC systems is related first to the NASA development of the Sylramic-iBN Sic fiber, which displays high thermal stability, creep resistance, rupture resistance, and thermal conductivity, and possesses an in-situ grown BN surface layer for added environmental durability. This fiber is simply derived from Sylramic Sic fiber type that is currently produced at ATK COI Ceramics. Further capability is then derived by using chemical vapor infiltration (CVI) to form the initial portion of the hybrid Sic matrix. Because of its high creep resistance and thermal conductivity, the CVI Sic matrix is a required base constituent for all the high temperature SiC/SiC systems. By subsequently thermo- mechanical-treating the CMC preform, which consists of the S ylramic-iBN fibers and CVI Sic matrix, process-related defects in the matrix are removed, further improving matrix and CMC creep resistance and conductivity.

Yun, H. M.↗

On the evolution of microstructure and defect control in 316L SS components fabricated via directed energy deposition

To identify the critical issues that affect the evolution of microstructure during additive manufacturing, we investigated the influence of process parameters on the evolution of the dimensional and surface quality, microstructure, internal defects, and mechanical properties in 316L stainless steel (SS) components fabricated using laser engineered net shaping (LENS®), a directed energy deposition (DED) additive manufacturing (AM) technique. The results show that the accumulation of un-melted powder particles on the side walls of deposited sections can be avoided by selecting a laser under-focused condition. Moreover, we report that the variation of melt pool width is more sensitive to laser power than to the depth of the melt pool. The formation of a so-called “hierarchical” microstructure with cellular morphology is attributable to a combination of layer deposition and rapid solidification, which are characteristics of AM. Finally, we discuss microstructure evolution and defect formation, particularly the formation of multiple interfaces and the presence of un-melted powder particles and pores, in light of the dynamic convective fluid flow and rapid solidification that occur in the melt pool. X-ray computed tomography (X-CT) was used to precisely map the spatial distribution of pores in the DED components. The evolution of microstructure during DED is discussed in the context of related thermal phenomena in an effort to provide fundamental insight into the mechanisms that govern defect formation.

36 MATERIALS SCIENCE↗

Correlation Between Microstructure and In-Field Performance of Zr-Added REBCO Coated Conductors Made by Advanced MOCVD

In this paper, we present correlation features between critical current density (J c ) and microstructural characteristics of Zr-added (0, 5, and 15 mol.%) REBa 2 Cu 3 O 7-x (REBCO and RE = rare earth) coated conductors fabricated by the novel advanced metal organic chemical vapor deposition technique. The J c along the tape normal (~ B || c-axis) measured by a vibrating sample magnetometer at 30 and 65 K and magnetic flux density range of 0-14 T was used for qualitative comparison of different Zr-added REBCO tapes. It is found that tapes with enhanced in-field J c exhibit a rise of critical current (plateau or fishtail effect) at magnetic flux density 1-8 T and temperatures 65 K. The TEM microstructure analysis indicates that the plateau effect is not the intrinsic property of REBCO matrix but depends on size distribution and density of BaZrO 3 (BZO) self-assembled nanocolumns. Two types of BZO microstructures have been identified: one with uniform BZO diameter 4-7 nm, whereas some films exhibit bottle-shaped BZO nanocolumns with alternating wide and narrow sections, 7-13 and 4-6 nm, respectively. The non-uniform shape and broad size distribution of BZO nanocolumns are correlated to more vortex pinning strength and matching field.

2G high-temperature superconductor (2GHTS)↗

The effects of microstructure and porosity on the competing fatigue failure mechanisms in powder metallurgy Ti-6Al-4V

In near-net-shape manufacturing methods, such as powder metallurgy, additive manufacturing, and metal injection molding, porosity has historically been viewed as the sole limiting factor for fatigue life. This is because pores tend to act as stress concentrators. However, in this work, a fractographic analysis of Ti-6Al-4V produced through several powder metallurgy techniques has shown that microstructural faceting due to slip can cause fatigue failure, even in the presence of porosity. The likelihood of pore related failure was found to be dependent on microstructure size and morphology. Further, a minimum pore size threshold was found to exist for each microstructure, under which pores will not cause fatigue failure. A simple model was developed to determine this threshold based on the microstructural characteristics of the material. This model was then compared to experimental data and properly predicted the fatigue failure mechanism in over 99% of the samples examined.

36 MATERIALS SCIENCE↗

Mechanistic origins of corrosion protection of aluminum alloys by graphene/polyetherimide nanocomposite coatings

Light-weighting vehicular components through adoption of light-metal structural alloys holds promise for reducing the fuel consumption of internal combustion engine vehicles and increasing the range of battery electric vehicles. However, the alloyed microstructure and surface precipitates of aluminum alloys render these materials susceptible to corrosion under modest excursions from neutral pH. Traditional chromium-based anodic passivation layers are subject to increasingly stringent environmental regulations, whereas options for sacrificial cathodic films are sparse for electropositive metals. While hybrid nanocomposite coatings have shown initial promise, mechanistic underpinnings remain poorly understood. Here, a fully imidized polyetherimide (PEI) resin is utilized as the continuous phase with inclusion of unfunctionalized exfoliated graphite (UFG). A comprehensive investigation of the mechanisms of corrosion protection reveals key fundamental design principles underpinning corrosion inhibition. First, strong interfacial adhesion, which for PEI is facilitated by binding of imide carbonyl moieties to Lewis acidic sites on Al surfaces. Second, the miscibility of ion-impervious nanoscopic UFG fillers and stabilization of a substantial interphase region at UFG/PEI boundaries that result in minimizing the free volume at the filler/polymer interface. Finally, extended tortuosity of ion diffusion pathways imbued by the below-percolation-threshold 2D fillers. These three design principles help govern and modulate ion transport from electrolyte/coating interfaces to the coating/metal interface and are crucial for the extended preservation of barrier properties. The results suggest an approach to systematically activate multiple modes of corrosion inhibition through rational design of hybrid nanocomposite coatings across hard-to-abate sectors where light metal alloys are likely to play an increasingly prominent role.

36 MATERIALS SCIENCE↗