SEARCH · Search NASA

Results for “mode shape”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

All sources NASA NTRS DOE OSTI

NASA NTRS1986

Ground vibration test results for Drones for Aerodynamic and Structural Testing (DAST)/Aeroelastic Research Wing (ARW-1R) aircraft

The drones for aerodynamic and structural testing (DAST) project was designed to control flutter actively at high subsonic speeds. Accurate knowledge of the structural model was critical for the successful design of the control system. A ground vibration test was conducted on the DAST vehicle to determine the structural model characteristics. This report presents and discusses the vibration and test equipment, the test setup and procedures, and the antisymmetric and symmetric mode shape results. The modal characteristics were subsequently used to update the structural model employed in the control law design process.

Cox, T. H.↗

NASA NTRS1986

An approximate buckling analysis for rectangular orthotropic plates with centrally located cutouts

An approximate analysis for predicting buckling of rectangular orthotropic composite plates with centrally located cutouts is presented. In this analysis, prebuckling and buckling problems are converted from a two-dimensional to a one-dimensional system of linear differential equations with variable coefficients. The conversion is accomplished by expressing the displacements as series with each element containing a trigonometric function of one coordinate and a coefficient that is an arbitrary function of the other coordinate. Ordinary differential equations are then obtained from a variational principle. Analytical results obtained from the approximate analysis are compared with finite element analyses for isotropic plates and for specially orthotropic plates with central circular cutouts of various sizes. Experimental results for the specially orthotropic plates are also presented. In nearly all cases, the approximate analysis predicts the buckling mode shapes correctly and predicts the buckling loads to within a few percent of the finite element and experimental results.

Nemeth, M. P.↗

NASA NTRS1984

Advanced turboprop vibratory characteristics

The assembly of SR5 advanced turboprop blades to develop a structural dynamic data base for swept props is reported. Steady state blade deformation under centrifugal loading and vibratory characteristics of the rotor assembly were measured. Vibration was induced through a system of piezoelectric crystals attached to the blades. Data reduction procedures are used to provide deformation, mode shape, and frequencies of the assembly at predetermined speeds.

Srinivasan, A. V.↗

NASA NTRS1986

Solving large-scale dynamic systems using band Lanczos method in Rockwell NASTRAN on CRAY X-MP

The improved cost effectiveness using better models, more accurate and faster algorithms and large scale computing offers more representative dynamic analyses. The band Lanczos eigen-solution method was implemented in Rockwell's version of 1984 COSMIC-released NASTRAN finite element structural analysis computer program to effectively solve for structural vibration modes including those of large complex systems exceeding 10,000 degrees of freedom. The Lanczos vectors were re-orthogonalized locally using the Lanczos Method and globally using the modified Gram-Schmidt method for sweeping rigid-body modes and previously generated modes and Lanczos vectors. The truncated band matrix was solved for vibration frequencies and mode shapes using Givens rotations. Numerical examples are included to demonstrate the cost effectiveness and accuracy of the method as implemented in ROCKWELL NASTRAN. The CRAY version is based on RPK's COSMIC/NASTRAN. The band Lanczos method was more reliable and accurate and converged faster than the single vector Lanczos Method. The band Lanczos method was comparable to the subspace iteration method which was a block version of the inverse power method. However, the subspace matrix tended to be fully populated in the case of subspace iteration and not as sparse as a band matrix.

Gupta, V. K.↗

NASA NTRS1986

Structureborne noise in aircraft: Modal tests

As part of an investigation to develop measurement techniques for structureborne noise, three modal surveys have been conducted on an OV-10A aircraft and the results have been presented. The purpose of the modal surveys was to identify suitable locations for mounting accelerometer and strain gages in subsequent tests in which transfer functions relating wing vibration to interior noise were to be determined. These surveys are as follows:(1) wing/fuselage modal survey utilizing one shaker under the right wing; (2) complete wing modal survey utilizing two shakers, one under each wing; and (3) fuselage side panel modal survey utilizing a small instrumented hammer. The predominant frequencies and damping ratios for each analysis were listed in tables. The primary mode shapes at the lower frequencies and at frequencies near the expected engine driving frequencies have been shown for each survey.

Clevenson, S. A.↗

NASA NTRS1986

Advanced optical measuring systems for measuring the properties of fluids and structures

Four advanced optical models are reviewed for the measurement of visualization of flow and structural properties. Double-exposure, diffuse-illumination, holographic interferometry can be used for three-dimensional flow visualization. When this method is combined with optical heterodyning, precise measurements of structural displacements or fluid density are possible. Time-average holography is well known as a method for displaying vibrational mode shapes, but it also can be used for flow visualization and flow measurements. Deflectometry is used to measure or visualize the deflection of light rays from collimation. Said deflection occurs because of refraction in a fluid or because of reflection from a tilted surface. The moire technique for deflectometry, when combined with optical heterodyning, permits very precise measurements of these quantities. The rainbow schlieren method of deflectometry allows varying deflection angles to be encoded with colors for visualization.

Decker, A. J.↗

NASA NTRS1985

Vibration analysis of rotating turbomachinery blades by an improved finite difference method

The problem of calculating the natural frequencies and mode shapes of rotating blades is solved by an improved finite difference procedure based on second-order central differences. Lead-lag, flapping and coupled bending-torsional vibration cases of untwisted blades are considered. Results obtained by using the present improved theory have been observed to be close lower bound solutions. The convergence has been found to be rapid in comparison with the classical first-order finite difference method. While the computational space and time required by the present approach is observed to be almost the same as that required by the first-order theory for a given mesh size, accuracies of practical interest can be obtained by using the improved finite difference procedure with a relatively smaller matrix size, in contrast to the classical finite difference procedure which requires either a larger matrix or an extrapolation procedure for improvement in accuracy.

Subrahmanyam, K. B.↗

NASA NTRS1985

Longitudinal compressive failure modes in fiber composites End attachment effects on IITRI type test specimens

The end-attachment effects on longitudinal compressive strength of IITRI type specimen unidirectional fiber composites are formally assessed using finite-element analysis (FEA) in conjunction with composite mechanics. Sixteen different cases were analyzed to evaluate end-attachment effects (such as degree of misalignment, type of misalignment, progressive end-tab debonding, and specimen thickness) on stress distribution, peak stresses, buckling loads, and buckling mode shapes. The results obtained from the FEA and comparisons with fractured specimens show that eccentricities induce bending-type stresses which peak near the end-tabs and cause flexural type fracture. Also, guidelines are included for placing back-to-back strain gages to measure the presence/absence of possible end-attachment and eccentricity effects.

Chamis, C. C.↗

NASA NTRS1985

Structural analysis model validation using modal test data

The design of a structure which can survive a prescribed dynamic environment is generally based on the use of an analytical model of the structure. The modal test is employed to verify the analytical model. This paper is concerned with the involved validation process, taking into account modal test results from realistic complex spacecraft structural systems as examples to demonstrate the proposed validation procedure. Attention is given to a load analysis model definition, a pretest analysis and test/analysis model, and the correlation parameters. Coordinate transformation is considered along with mode identification, frequency orthogonality, effective mass, mode shape, local kinetic energy, modal force, strain energy, and modal forces by acceleration measurements. Two examples are used to illustrate the procedure.

Chen, J.-C.↗

NASA NTRS1985

The use of an optical data acquisition system for bladed disk vibration analysis

A new concept in instrumentation was developed by engineers at NASA Lewis Research Center to collect vibration data from multi-bladed rotors. This new concept, known as the optical data acquisition system, uses optical transducers to measure bladed tip deflections by reflection of light beams off the tips of the blades as they pass in front of the optical transducer. By using an array of transducers around the perimeter of the rotor, detailed vibration signals can be obtained. In this study, resonant frequencies and mode shapes were determined for a 56 bladed rotor using the optical system. Frequency data from the optical system was also compared to data obtained from strain gauge measurements and finite element analysis and was found to be in good agreement.

Lawrence, C.↗

NASA NTRS1986

Effects of an internal floor on low frequency sound transmission into aircraft cabins - An experimental investigation

A simplified cylindrical model of an aircraft fuselage is used to experimentally study the effects of an internal floor on low frequency sound transmission into aircraft cabins. A scaled-down lattice floor support and floor skin are designed based upon selected characteristics of a business aircraft. Thus, the model provides a simplified procedure for studying the effects of various structural modifications as well as other important effects. Modal decomposition of the shell response and the corresponding pressure response at various interior locations are presented. Results indicate that the main effect of the floor on interior pressure levels is due to modification of the interior acoustic mode shape and not due to the structural modification of the fuselage caused by the lattice floor support.

Jones, J. D.↗

NASA NTRS1986

Controller design via structural reduced modeling by FETM

The Finite Element - Transfer Matrix (FETM) method has been developed to reduce the computations involved in analysis of structures. This widely accepted method, however, has certain limitations, and does not directly produce reduced models for control design. To overcome these shortcomings, a modification of FETM method has been developed. The modified FETM method easily produces reduced models that are tailored toward subsequent control design. Other features of this method are its ability to: (1) extract open loop frequencies and mode shapes with less computations, (2) overcome limitations of the original FETM method, and (3) simplify the procedures for output feedback, constrained compensation, and decentralized control. This semi annual report presents the development of the modified FETM, and through an example, illustrates its applicability to an output feedback and a decentralized control design.

Yousuff, A.↗

NASA NTRS1986

Concentrated mass effects on the flutter of a composite advanced turboprop model

The effects on bending-torsion flutter due to the addition of a concentrated mass to an advanced turboprop model blade with rigid hub are studied. Specifically the effects of the magnitude and location of added mass on the natural frequencies, mode shapes, critical interblade phase angle, and flutter Mach number are analytically investigated. The flutter of a propfan model is shown to be sensitive to the change in mass distribution. Static unbalance effects, like those for fixed wings, were shown to occur as the concentrated mass was moved from the leading edge to the trailing edge with the exception of one mass location. Mass balancing is also inferred to be a feasible method for increasing the flutter speed.

Ramsey, J. K.↗

NASA NTRS1987

Analytical and experimental investigation of mistuning in propfan flutter

An analytical and experimental investigation of the effects of mistuning on propfan subsonic flutter was performed. The analytical model is based on the normal modes of a rotating composite blade and a three-dimensinal subsonic unsteady lifting surface aerodynamic theory. Theoretical and experimental results are compared for selected cases at different blade pitch angles, rotational speeds, and free-stream Mach numbers. The comparison shows a reasonably good agreement between theory and experiment. Both theory and experiment showed that combined mode shape, frequency, and aerodynamic mistuning can have a beneficial or adverse effect on blade damping depending on Mach number. Additional parametric results showed that alternative blade frequency mistuning does not have enough potential for it to be used as a passive flutter control in propfans similar to the one studied. It can be inferred from the results that a laminated composite propfan blade can be tailored to optimize its flutter speed by selecting the proper ply angles.

Kaza, Krishna Rao V.↗

NASA NTRS1986

The effect of a small initial curvature on the free vibration of clamped, rectangular plates

An analytical method of obtaining the natural frequencies and mode shapes of clamped, rectangular plates having a small initial curvature is presented. Specifically, the singular perturbation technique is used to reduce the fourth-order plate vibration problem to the simpler membrane problem with modified boundary conditions that account for the bending effects. The eigenfrequencies for plates with inverse aspect ratios varying between 0.1 and 1.0 and for the dimensionless normal prestress between 0.1 and 1.0 have been presented for values of epsilon, the normalized bending rigidity, ranging between 0.0010 and 0.2500. It is established that a small initial curvature has no effect on the frequency of vibration of the plate. However, its effect is manifested in the eigenmodes.

Adeniji-Fashola, A. A.↗

NASA NTRS1987

Initial investigations into the damping characteristics of wire rope vibration isolators

Passive dampers composed of coils of multi-strand wire rope are investigated. Analytical results range from those produced by complex NASTRAN models to those of a Coulomb damping model with variable friction force. The latter agrees well with experiment. The Coulomb model is also utilized to generate hysteresis loops. Various other models related to early experimental investigations are described. Significant closed-form static solutions for physical properties of single-and multi-strand wire ropes are developed for certain specific geometries and loading conditions. NASTRAN models concentrate on model generation and mode shapes of 2-strand and 7-strand straight wire ropes with interfacial forces.

Cutchins, M. A.↗

NASA NTRS1985

Structural and aeroelastic analysis of the SR-7L propfan

A structural and aeroelastic analysis of a large scale advanced turboprop rotor blade is presented. This 8-blade rotor is designed to operate at Mach 0.8 at an altitude of 35,000 ft. The blades are highly swept and twisted and of spar/shell construction. Due to the complexity of the blade geometry and its high performance, it is subjected to much higher loads and tends to be much less stable than conventional blades. Four specific analyses were conducted: (1) steady deflection; (2) natural frequencies and mode shapes; (3) steady stresses; and (4) aeroelastic stability. State-of-the-art methods were used to analyze the blades including a large deflection, finite element structural analysis, and an aeroelastic analysis including interblade aerodynamic coupling (cascade effects). The study found the blade to be structurally sound and aeroelastically stable. However, it clearly indicated that advanced turboprop blades are much less robust than conventional blades and must be analyzed and fabricated much more carefully in order to assure that they are structurally sound and aeroelastically stable.

Hirschbein, Murray↗

NASA NTRS1987

Computer animation of modal and transient vibrations

An interactive computer graphics processor is described that is capable of generating input to animate modal and transient vibrations of finite element models on an interactive graphics system. The results from NASTRAN can be postprocessed such that a three dimensional wire-frame picture, in perspective, of the finite element mesh is drawn on the graphics display. Modal vibrations of any mode shape or transient motions over any range of steps can be animated. The finite element mesh can be color-coded by any component of displacement. Viewing parameters and the rate of vibration of the finite element model can be interactively updated while the structure is vibrating.

Lipman, Robert R.↗