Search NASA⌕ Search

SEARCH · Search NASA

Results for “model reporting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

SuperCam Body Unit Flight Model Vibration Test Report (Rev.A)

This report describes the vibration tests that were applied to the SuperCam Body Unit (SCBU) Flight Model (FM) at Protoflight levels. These tests were performed November 28 and 29, 2018, at the Los Alamos National Laboratory ISR-5 Shock and Vibration Environmental Test Facility, at TA-3, Building 502 Room E102. The test environments shown below were obtained from the SuperCam FM test plan, which is the overarching document for all testing. The vibration results from all testing are shown below. An anomaly was identified during the FM functional testing at the conclusion of the X-Axis. It was decided to re-test at -6 dB to determine if the anomaly progressed or remained the same. Functional testing did not show any changes after the -6 dB random vibration. It was then decided to re-test at -3 dB. Once again functional testing after the -3 dB vibration did not show any changes. Low-level random vibration signature surveys were performed before and after the -6 dB and -3 dB retests. This test series met the vibration requirements to qualify the SuperCam Body Unit FM for flight without any significant anomalies.

42 ENGINEERING↗

Aeroelasticity and mechanical stability report, 0.27 Mach scale model of the YAH-64 advanced attack helicopter

A 27% dynamically scaled model of the YAH-64 Advanced Attack Helicopter main rotor and hub has been designed and fabricated. The model will be tested in the NASA Langley Research Center V/STOL wind tunnel using the General Rotor Model System (GRMS). This report documents the studies performed to ensure dynamic similarity of the model with its full scale parent. It also contains a preliminary aeroelastic and aeromechanical substantiation for the rotor installation in the wind tunnel. From the limited studies performed no aeroelastic stability or load problems are projected. To alleviate a projected ground resonance problem, a modification of the roll characteristics of the GRMS is recommended.

Straub, F. K.↗

Characterization of oceanic post-cold frontal clouds and their model representation. Final report

Low-level clouds are ubiquitous over the oceans, and their impact on the Earth’ radiative budget is important. However, general circulation models (GCMs) that are used to represent our climate and its evolution still experience problems to represent their correct amount and radiative impact. In the extratropical latitudes (~30-60 N/S), cloud properties are strongly modulated by the occurrence of anti-cyclones (high pressure systems) and cyclones (low pressure systems). While deep clouds dominate in cyclones near the center and along the cold and warm fronts, low-level clouds populate the colder regions of the cyclones, and more specifically the region in the wake of the cold fronts, the post-cold frontal region (PCF). The GCMs mentioned above were found to underestimate the amount of these PCF clouds, and this caused errors in their representation of the amount of solar radiation at the surface of the southern hemisphere oceans, causing an excess in absorption and errors in long-term predictions. To better understand which processes are ill-represented in the GCMs to cause such issues, we used ground-based observations from the Eastern North Atlantic (ENA) ARM site and a high resolution regional model (called WRF) to examine the properties of PCF clouds. With the WRF model, we simulated the passage of a cold front at the ENA site using theoretically distinct representations of convection and the physics of the boundary layer. While these physical representations had little impact on the timing, structure and circulation of the cold front, we found a high sensitivity to how the large scale information was fed into the model. Errors rapidly developed if the incoming flow information was injected too far from the site, but 1000 km was found to be an optimal distance between the outer boundary and the ENA site for a realistic cold front passage. With this model, we then conducted a series of experiment where convection and boundary layer schemes were changed, and revealed that 1) the clouds were more sensitive to the convection than boundary layer schemes and 2) the interaction between the two has a large impact. Furthermore, changing the representation of the physics in the model had greater impacts on PCF clouds than changing the initial conditions. As large-scale models increase their spatial resolution, convection will eventually be resolved but it remains that their representation of the physics of the boundary layer will matter for the correct representation of shallow (low-level) clouds. Observations were used to find which large-scale information had a clear relationship with PCF cloud and precipitation properties, in view of helping with GCM parameterizations and evaluation. Both lower troposphere stability and surface forcing were found to be important for PCF clouds that experience more vigorous dynamics than their tropical or subtropical counterparts. For cloud base and top heights, a simple measure of the change in potential temperature between the surface and the 800 hPa was found to be a good predictor. This relationship was found to hold as well when using data from campaigns recently conducted in the southern ocean south of Tasmania. A recent GCM was found to succeed in representing similar relations. For cloud depth, water content, and different characteristics of precipitation both the temperature contrast between the surface and near-air and the near-surface wind speed had a strong relationship. To summarize, through observational constraints and regional model experiments, the project has provided guidance to evaluate GCMs and tools to improve their representation of low-level clouds in the extratropics. It has also highlighted differences in behavior between these clouds and those typically found in the subtropics, thus opening new avenues of research for shallow clouds in general.

54 ENVIRONMENTAL SCIENCES↗

Heavy Duty Hydrogen: Reference Station, Fueling Performance Test Device Concepts, and Station Capacity Model (CRADA Final Report)

This project will provide valuable information on (1) reference station design, (2) exploration of design concepts for a fueling performance test device, and (3) modeling of station capacity. The work applies to heavy-duty (HD) hydrogen fueling stations with large dispensing capacity and high flowrates servicing HD hydrogen trucks such as class 8 trucks in long haul applications. Additionally, a 4th area will provide near-real-time verification of fuel quality with on-site hydrogen contaminant detectors (HCDs) for use at both light-duty (LD) and HD stations. The work leverages national lab capabilities including staff and equipment at SNL, NLR, and ANL with collaboration and funding cost share from California agencies (CEC, SCAQMD, and GO-Biz). This project will provide tools and information that lead to more efficient design, acceptance, and commissioning of these larger capacity, higher flowrate stations serving HD applications. The HCD work will benefit both LD and HD stations. Note: The 4th area (HCD) mentioned above continued outside of this CRADA and will not be included in this report. There are no tasks included in this CRADA for HCD and the summary text for it should have been removed prior to this CRADA contract execution but remained in error and is included here for completeness.

08 HYDROGEN↗

K-3 Refractory Corrosion and Sulfate Solubility Model Enhancement (Final Report)

As higher waste loading LAW glasses are formulated, sulfate solubility and K-3 refractory corrosion are two properties that become increasingly constraining; however, WTP baseline models were not developed for these properties. In previous work for ORP, VSL/Atkins developed preliminary glass property-composition models that relate LAW glass composition to these two essential properties to support the implementation of the higher waste loading LAW glass formulations at the WTP. The development of the initial LAW glass property-composition models for K-3 refractory corrosion and sulfate solubility was completed in 2015. The present work scope focused on enhancement of these models and included augmentation of property-composition datasets for these two properties with newly available data, review of the updated datasets, and development of enhanced models.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Collaborative Research: Regional climate-change projections through next-generation empirical and dynamical models (Final Technical Report)

This is the final report for a DOE-funded research project describing the outcome of research on non-homogeneous hidden Markov models (NHMMs) and coupled ocean-atmosphere (O-A) intermediate-complexity models (ICMs) to identify the potentially predictable modes of climate variability, and to investigate their impacts on the regional-scale. The main results consist of extensive development of the hidden Markov models for rainfall simulation and downscaling specifically within the non-stationary climate change context together with the development of parallelized software; application of NHMMs to downscaling of rainfall projections over India; identification and analysis of decadal climate signals in data and models; and, studies of climate variability in terms of the dynamics of atmospheric flow regimes.

58 GEOSCIENCES↗

Numerical Simulation of Unsteady Aerodynamic Models

This report documents the results of the numerical simulations of unsteady aerodynamic models. The results focus on numerical accuracy and efficiency, and the robustness of the numerical methods. The aerodynamic models includes the classical Wagner and Kussner functions and the Leishman-Beddoes dynamic stall model. The simulations includes the numerical approximations of the Duhamel's integrals using both indicial (step) and impulse responses, the numerical integrations of the state-space models, and the exact solutions. The report also presents the conversion among different model representations.

Nguyen, Khanh Q.↗

Generative design of de novo proteins based on secondary-structure constraints using an attention-based diffusion model

We report two generative deep-learning models that predict amino acid sequences and 3D protein structures on the basis of secondary-structure design objectives via either the overall content or the per-residue structure. Both models are robust regarding imperfect inputs and offer de novo design capacity because they can discover new protein sequences not yet discovered from natural mechanisms or systems. The residue-level secondary-structure design model generally yields higher accuracy and more diverse sequences. These findings suggest unexplored opportunities for protein designs and functional outcomes within the vast amino acid sequences beyond known proteins. Our models, based on an attention-based diffusion model and trained on a dataset extracted from experimentally known 3D protein structures, offer numerous downstream applications in the conditional generative design of various biological or engineering systems. Future work could include additional conditioning and an exploration of other functional properties of the generated proteins for various properties beyond structural objectives.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Assessment of MARMOT Grain Growth Model

This report assesses the MARMOT grain growth model by comparing modeling predictions with experimental results from thermal annealing. The purpose here is threefold: (1) to demonstrate the validation approach of using thermal annealing experiments with non-destructive characterization, (2) to test the reconstruction capability and computation efficiency in MOOSE, and (3) to validate the grain growth model and the associated parameters that are implemented in MARMOT for UO 2 . To assure a rigorous comparison, the 2D and 3D initial experimental microstructures of UO 2 samples were characterized using non-destructive Synchrotron x-ray. The same samples were then annealed at 2273K for grain growth, and their initial microstructures were used as initial conditions for simulated annealing at the same temperature using MARMOT. After annealing, the final experimental microstructures were characterized again to compare with the results from simulations. So far, comparison between modeling and experiments has been done for 2D microstructures, and 3D comparison is underway. The preliminary results demonstrated the usefulness of the non-destructive characterization method for MARMOT grain growth model validation. A detailed analysis of the 3D microstructures is in progress to fully validate the current model in MARMOT.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Electron-Ion Dynamics with Time-Dependent Density Functional Theory: Towards Predictive Solar Cell Modeling: Final Technical Report

This project investigates the accuracy of currently-used functionals in time-dependent density functional theory, which is today routinely used to predict and design materials and computationally model processes in solar energy conversion. The rigorously-based electron-ion dynamics method developed here sheds light on traditional methods and overcomes challenges those methods have. The fundamental research undertaken here is important for building reliable and practical methods for materials discovery. The ultimate goal is to use these tools for the computational design of new materials for solar cell devices of high efficiency.

14 SOLAR ENERGY↗

Target Soil Impact Verification: Experimental Testing and Kayenta Constitutive Modeling.

This report details experimental testing and constitutive modeling of sandy soil deformation under quasi - static conditions. This is driven by the need to understand constitutive response of soil to target/component behavior upon impact . An experimental and constitutive modeling program was followed to determine elastic - plastic properties and a compressional failure envelope of dry soil . One hydrostatic, one unconfined compressive stress (UCS), nine axisymmetric compression (ACS) , and one uniaxial strain (US) test were conducted at room temperature . Elastic moduli, assuming isotropy, are determined from unload/reload loops and final unloading for all tests pre - failure and increase monotonically with mean stress. Very little modulus degradation was discernable from elastic results even when exposed to mean stresses above 200 MPa . The failure envelope and initial yield surface were determined from peak stresses and observed onset of plastic yielding from all test results. Soil elasto - plastic behavior is described using the Brannon et al. (2009) Kayenta constitutive model. As a validation exercise, the ACS - parameterized Kayenta model is used to predict response of the soil material under uniaxial strain loading. The resulting parameterized and validated Kayenta model is of high quality and suitable for modeling sandy soil deformation under a range of conditions, including that for impact prediction.

54 ENVIRONMENTAL SCIENCES↗

Multizone Residential HVAC Modeling

This report will evaluate several building physics modeling tools to determine which are best suited for developing next-generation zoning technology. These modeling tools will be evaluated for their ability to predict room-level thermal loads, HVAC system operation, temperature and comfort predictions, and scalability. Any gaps in the existing tools will be identified and a path forward will be discussed.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗