SEARCH · Search NASA

Results for “quantum limits”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

458 records · Page 26

All sources NASA NTRS DOE OSTI

NASA NTRS2018

Quantitative validation of Ames IR intensity and new line lists for (32/33/34)S(16)O2, (32)S(18)O2 and (16)O(32)S(18)O

The quality of Ames-296K SO2 Infrared (IR) line list intensities is first validated by quantitative exploration of several dipole moment surfaces (DMSs) and partition sum convergence. The DMSs are computed with several of Dunning’s correlation-consistent basis sets and their vibrational dependence are compared to the empirical model derived from Stark effect experiments reported by D. Patel, D. Margolese, and T.R. Dykea [J.Chem.Phys. 70, 2740 (1979)]. The effective dipole deviations from the DMS adopted in the Ames IR lists is 0.2-0.4% for vibrational states up to 3v3. The vibrational dependence of the dipole moment is also in good agreement, except for nv1. Partition sum convergence at 296K is confirmed by new calculations with rotational quantum number J up to 150 and upper state E’ up to 8000 cm-1. The isotopologue consistency of the Ames IR line lists is superior relative to the regular Effective Hamiltonian (EH) models and Effective Dipole Moment (EDM) models. The v1+v2 and v2+v3 intensity consistency check reveals the recently reported experimental intensities need significant improvement or re-analysis. After the accuracy, convergence, and isotopologue consistency have been confirmed, the theoretical Ames-296K intensities are combined with the experimental line positions or EH models that experimental spectroscopists published after 2009. Three high-resolution IR line sets are reported for the (32/33/34)S(16)O2, (32)S(18)O2 and (16)O(32)S(18)O isotopologues: (1) the “New Lines Sets” include experimentally measured line positions; (2) the “Expanded Line Sets” include possible transitions among new rovibrational levels assigned in experiments and ground state (GS) levels predicted by reliable EH models; (3) the “Ames + MARVEL Sets” include possible transitions among all those levels reported in a recent MARVEL analysis. [Tóbiás et al, JQSRT 208, 152 (2018)]. Compared to the limited data in High-resolution TRANsmission molecular absorption database (HITRAN), these line sets have significantly improved the data coverage up to 4000 cm-1. Some missing bands can be traced to the unpublished experimental data. The isotopologue consistency of these line sets will help identify the uncertainties and defects in the experimental EH and EDM models. These line sets are good candidates for the next HITRAN update, if line shape parameters are available. The line sets can be downloaded from supplementary files or from the Ames Molecular Spectroscopic Database at http://huang.seti.org.

Xinchuan Huang↗

NASA NTRS2007

Nanorod-Based Fast-Response Pressure-Sensitive Paints

A proposed program of research and development would be devoted to exploitation of nanomaterials in pressuresensitive paints (PSPs), which are used on wind-tunnel models for mapping surface pressures associated with flow fields. Heretofore, some success has been achieved in measuring steady-state pressures by use of PSPs, but success in measuring temporally varying pressures has been elusive because of the inherent slowness of the optical responses of these materials. A PSP contains a dye that luminesces in a suitable wavelength range in response to photoexcitation in a shorter wavelength range. The luminescence is quenched by oxygen at a rate proportional to the partial pressure of oxygen and thus proportional to the pressure of air. As a result, the intensity of luminescence varies inversely with the pressure of air. The major problem in developing a PSP that could be easily applied to a wind-tunnel model and could be useful for measuring rapidly varying pressure is to provide very high gas diffusivity for rapid, easy transport of oxygen to and from active dye molecules. Most PSPs include polymer-base binders, which limit the penetration of oxygen to dye molecules, thereby reducing responses to pressure fluctuations. The proposed incorporation of nanomaterials (somewhat more specifically, nanorods) would result in paints having nanostructured surfaces that, relative to conventional PSP surfaces, would afford easier and more nearly complete access of oxygen molecules to dye molecules. One measure of greater access is effective surface area: For a typical PSP as proposed applied to a given solid surface, the nanometer-scale structural features would result in an exposed surface area more than 100 times that of a conventional PSP, and the mass of proposed PSP needed to cover the surface would be less than tenth of the mass of the conventional PSP. One aspect of the proposed development would be to synthesize nanorods of Si/SiO2, in both tangle-mat and regular- array forms, by use of chemical vapor deposition (CVD) and wet chemical processes, respectively. The rods would be coated with a PSP dye, and the resulting PSP signals would be compared with those obtained from PSP dye coats on conventional support materials. Another aspect of the proposed development would be to seek to exploit the quantum properties of nanorods of a suitable semiconductor (possibly GaN), which would be synthesized by CVD. These quantum properties of semiconductor nanorods include narrow-wavelength-band optical absorption and emission characteristics that vary with temperature. The temperature sensitivity might enable simultaneous measurement of fluctuating temperature and pressure and to provide a temperature correction for the PSP response.

Bencic, Timothy↗

NASA NTRS2007

Improved Readout Scheme for SQUID-Based Thermometry

An improved readout scheme has been proposed for high-resolution thermometers, (HRTs) based on the use of superconducting quantum interference devices (SQUIDs) to measure temperature- dependent magnetic susceptibilities. The proposed scheme would eliminate counting ambiguities that arise in the conventional scheme, while maintaining the superior magnetic-flux sensitivity of the conventional scheme. The proposed scheme is expected to be especially beneficial for HRT-based temperature control of multiplexed SQUIDbased bolometer sensor arrays. SQUID-based HRTs have become standard for measuring and controlling temperatures in the sub-nano-Kelvin temperature range in a broad range of low-temperature scientific and engineering applications. A typical SQUIDbased HRT that utilizes the conventional scheme includes a coil wound on a core made of a material that has temperature- dependent magnetic susceptibility in the temperature range of interest. The core and the coil are placed in a DC magnetic field provided either by a permanent magnet or as magnetic flux inside a superconducting outer wall. The aforementioned coil is connected to an input coil of a SQUID. Changes in temperature lead to changes in the susceptibility of the core and to changes in the magnetic flux detected by the SQUID. The SQUID readout instrumentation is capable of measuring magnetic-flux changes that correspond to temperature changes down to a noise limit .0.1 nK/Hz1/2. When the flux exceeds a few fundamental flux units, which typically corresponds to a temperature of .100 nK, the SQUID is reset. The temperature range can be greatly expanded if the reset events are carefully tracked and counted, either by a computer running appropriate software or by a dedicated piece of hardware.

Penanen, Konstantin↗

NASA NTRS1987

Potential surfaces for O atom-polymer reactions

Ab initio quantum chemistry methods are used to study the energetics of interactions of O atoms with organic compounds. Polyethylene (CH2)n has been chosen as the model system to study the interactions of O(3P) and O(1D) atoms with polymers. In particular, H abstraction is investigated and polyethylene is represented by a C3 (propane) oligomeric model. The gradient method, as implemented in the GRADSCF package of programs, is used to determine the geometries and energies of products and reactants. The saddle point, barrier geometry is determined by minimizing the squares of the gradients of the potential with respect to the internal coordinates. To correctly describe the change in bonding during the reaction at least a two configuration MCSCF (multiconfiguration self consistent field) or GVB (generalized valence bond) wave function has to be used. Basis sets include standard Pople and Dunning sets, however, increased with polarization functions and diffuse p functions on both the C and O atoms. The latter is important due to the O(-) character of the wave function at the saddle point and products. Normal modes and vibrational energy levels are given for the reactants, saddle points and products. Finally, quantitative energetics are obtained by implementing a small CAS (complete active space) approach followed by limited configuration interaction (CI) calculations. Comparisons are made with available experimental data.

Laskowski, B. C.↗

NASA NTRS1999

Capella: Structure and Abundances

This grant covers the analysis of EUVE spectra of the cool star binary system Capella. This project has also required the analysis of simultaneous Advanced Satellite for Cosmology and Astrophysics (ASCA) data. The ASCA spectrum of Capella could not be fit with standard models; by imposing models based on strong lines observed with EUVE, a problem wavelength region was identified. Correcting the problem required calculations of atomic collision strengths of higher principal quantum number than had ever been calculated. With these new models applied to the ASCA spectrum, better fits were obtained. Findings are that: (1) ASCA and EUVE spectra are both dominated by a region at 6 x 10(exp 6) K. (2) The high energy cut-off of the ASCA spectrum is consistent with emission from the highest ionization stages of EUVE, namely Fe XXIV. (3) EUVE requires a continuous emission measure distribution with more than two temperatures. (4) The ASCA spectra are of such high statistical significance that systematic uncertainties dominate, including atomic physics issues and calibration issues. (5) While the ASCA spectral fits achieve lower Chi(exp 2 with two-temperature fits, the EUVE-derived emission measure distribution models are also consistent with the spectra. (6) The Fe/H ratio obtained from the ASCA fit is within 20 % of the Fe/H abundance obtained from the summed spectra of Capella over 5 EUVE pointings, as well as the 1996 EUVE data. This result confirms our claims that quasi-continua composed of weak emission lines in the short wavelength spectrometer of EUVE are not major contributors to the measured Capella continuum. Other abundance ratios are also determined from the ASCA data, using models derived with EUVE. Si, Si, and Mg appear to be close to solar photospheric values, while the ratio of Ne/Fe is three to four times lower than solar photospheric values. Whether there is a general First Ionization Potential (FIP) effect or a specific neon anomaly cannot be determined from these data. (8) EUVE line ratios indicating low optical depth place limits on the extent to which the X-ray lines are optically, thick. While the brightest lines may be marginally thick, the ASCA spectrum is not of sufficient resolution to determine the optical depth in these lines.

Brickhouse, Nancy S.↗

NASA NTRS2024

Accurate Infrared Line Lists for 20 Isotopologues of CS 2 at Room Temperature

To facilitate atmospheric and spectroscopic studies of carbon disulfide, or CS 2 , in both planetary and exoplanetary atmospheres, we adopt the “Best Theory + Reliable High-resolution Experiment” algorithm to generate semiempirical IR line lists for the 20 most abundant CS 2 isotopologues, denoted as Ames-296K. The IR lists are computed using the Ames-1 potential energy surface, refined using the experimental transition set and an ab initio dipole moment surface fitted from CCSD(T)/aug-cc-pV(T/Q/5+d)Z dipoles extrapolated to a one-particle basis set limit. The IR lists cover the range of 0–10,000 cm -1 , with an S 296K cutoff at 10 -31 cm -1 /molecule·cm -2 (abundance included). A “natural” IR line list at 296 K includes about 10 million lines of the 20 isotopologues, with their intensities scaled by the corresponding abundances. The zero-point energy, partition functions, and abundances are reported for each isotopologue. The energy levels in the global effective Hamiltonian model for 12 C 32 S 2 are adopted to improve the line position accuracy. This new IR list for the main isotopologue is denoted as A+I.296K. Reliable HITRAN2020 line positions are also utilized to improve the accuracy of the 32 S 12 C 34 S, 32 S 12 C 33 S, and 32 S 13 C 32 S isotopologue line lists. The final composite line list is validated against Pacific Northwest National Laboratory experimental cross sections, showing excellent agreement. The agreement supports the quality of the composite line list and the power of synergy between experiment and theory. The new data are proposed for use in updating and expanding the CS 2 data in HITRAN and other high-resolution IR databases. Supplementary files are available in Zenodo and AHED.

Exoplanet atmospheric composition↗

NASA NTRS2003

Using Correlated Photons to Suppress Background Noise

A proposed method of suppressing the effect of background noise in an optical communication system would exploit the transmission and reception of correlated photons at the receiver. The method would not afford any advantage in a system in which performance is limited by shot noise. However, if the performance of the system is limited by background noise (e.g., sunlight in the case of a free-space optical communication system or incoherently scattered in-band photons in the case of a fiber-optic communication system), then the proposed method could offer an advantage: the proposed method would make it possible to achieve a signal-to-noise ratio (S/N) significantly greater than that of an otherwise equivalent background- noise-limited optical communication system based on the classical transmission and reception of uncorrelated photons. The figure schematically depicts a classical optical-communication system and a system according to the proposed method. In the classical system, a modulated laser beam is transmitted along an optical path to a receiver, the optics of which include a narrow-band-pass filter that suppresses some of the background noise. A photodetector in the receiver detects the laser-beam and background photons, most or all of which are uncorrelated. In the proposed system, correlated photons would be generated at the transmitter by making a modulated laser beam pass through a nonlinear parametric down-conversion crystal. The sum of frequencies of the correlated photons in each pair would equal the frequency of the incident photon from which they were generated. As in the classical system, the correlated photons would travel along an optical path to a receiver, where they would be band-pass filtered and detected. Unlike in the classical system, the photodetector in the receiver in this system would be one that intrinsically favors the detection of pairs of correlated photons over the detection of uncorrelated photons. Even though there would be no way of knowing the precise location and time of creation of a given pair of correlated signal photons in the nonlinear down-conversion crystal, the fact that the photons are necessarily created at the same time and place makes it possible to utilize conventional geometrical imaging optics to reunite the photons in coincidence in the receiving photodetector. Because most or all of the signal photons would be correlated while most or all of the noise photons would be uncorrelated, the S/N would be correspondingly enhanced in the photodetector output. An additional advantage to be gained by use of a correlated-photon detector is that it could be capable of recovering the signal even in the presence of background light so bright that a classical uncorrelated-photon detector would be saturated. A blocked-impurity-band (BIB) photodetector that preferentially detects pairs of correlated photons over uncorrelated ones and that operates at a quantum efficiency of 88 percent is commercially available. This detector must be cooled to the temperature of liquid helium to obtain the desired low-noise performance. It is planned to use this detector in a proof-of-principle demonstration. In addition, it may be possible to develop GaN-based photodetectors that could offer the desired low-noise performance at room temperature.

Jackson, Deborah↗

NASA NTRS2004

Application of Simulated Annealing and Related Algorithms to TWTA Design

Simulated Annealing (SA) is a stochastic optimization algorithm used to search for global minima in complex design surfaces where exhaustive searches are not computationally feasible. The algorithm is derived by simulating the annealing process, whereby a solid is heated to a liquid state and then cooled slowly to reach thermodynamic equilibrium at each temperature. The idea is that atoms in the solid continually bond and re-bond at various quantum energy levels, and with sufficient cooling time they will rearrange at the minimum energy state to form a perfect crystal. The distribution of energy levels is given by the Boltzmann distribution: as temperature drops, the probability of the presence of high-energy bonds decreases. In searching for an optimal design, local minima and discontinuities are often present in a design surface. SA presents a distinct advantage over other optimization algorithms in its ability to escape from these local minima. Just as high-energy atomic configurations are visited in the actual annealing process in order to eventually reach the minimum energy state, in SA highly non-optimal configurations are visited in order to find otherwise inaccessible global minima. The SA algorithm produces a Markov chain of points in the design space at each temperature, with a monotonically decreasing temperature. A random point is started upon, and the objective function is evaluated at that point. A stochastic perturbation is then made to the parameters of the point to arrive at a proposed new point in the design space, at which the objection function is evaluated as well. If the change in objective function values (Delta)E is negative, the proposed new point is accepted. If (Delta)E is positive, the proposed new point is accepted according to the Metropolis criterion: rho((Delta)f) = exp((-Delta)E/T), where T is the temperature for the current Markov chain. The process then repeats for the remainder of the Markov chain, after which the temperature is decremented and the process repeats. Eventually (and hopefully), a near-globally optimal solution is attained as T approaches zero. Several exciting variants of SA have recently emerged, including Discrete-State Simulated Annealing (DSSA) and Simulated Tempering (ST). The DSSA algorithm takes the thermodynamic analogy one step further by categorizing objective function evaluations into discrete states. In doing so, many of the case-specific problems associated with fine-tuning the SA algorithm can be avoided; for example, theoretical approximations for the initial and final temperature can be derived independently of the case. In this manner, DSSA provides a scheme that is more robust with respect to widely differing design surfaces. ST differs from SA in that the temperature T becomes an additional random variable in the optimization. The system is also kept in equilibrium as the temperature changes, as opposed to the system being driven out of equilibrium as temperature changes in SA. ST is designed to overcome obstacles in design surfaces where numerous local minima are separated by high barriers. These algorithms are incorporated into the optimal design of the traveling-wave tube amplifier (TWTA). The area under scrutiny is the collector, in which it would be ideal to use negative potential to decelerate the spent electron beam to zero kinetic energy just as it reaches the collector surface. In reality this is not plausible due to a number of physical limitations, including repulsion and differing levels of kinetic energy among individual electrons. Instead, the collector is designed with multiple stages depressed below ground potential. The design of this multiple-stage collector is the optimization problem of interest. One remaining problem in SA and DSSA is the difficulty in determining when equilibrium has been reached so that the current Markov chain can be terminated. It has been suggested in recent literature that simulating the thermodynamic properties opecific heat, entropy, and internal energy from the Boltzmann distribution can provide good indicators of having reached equilibrium at a certain temperature. These properties are tested for their efficacy and implemented in SA and DSSA code with respect to TWTA collector optimization.

Radke, Eric M.↗