Search NASA⌕ Search

SEARCH · Search NASA

Results for “shuttle effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Silica RSI for Application to the Shuttle Orbiter

Silica reusable surface insulation is analyzed for its cold soak properties, bond properties at low temperature, gap and step heating effects, and aerodynamic surface roughness effects to determine space shuttle weight and cost sensitivity to structure subsystem weights. Computerized simulation studies show that total program cost savings of silica (vs. mullite) exceed thermal protection system design and development costs and that an early introduction of silica increases total program cost savings.

Forsberg, K. J.↗

Effects of forced and free convections on structural temperatures of Space Shuttle Orbiter during reentry flight

Structural performance and resizing (SPAR) finite-element thermal analysis computer program was used in the heat transfer analysis of the Space Shuttle Orbiter wing subjected to reentry aerodynamic heating. With sufficient external forced convective cooling near the end of the heating cycle, the calculated surface temperatures of the thermal protection system (TPS) agree favorably with the flight data for the entire flight profile. However, the effects of this external forced convective cooling on the structural temperatures were found to be negligible. Both free convection and forced convection elements were introduced to model the internal convection effect of the cool air entering the Shuttle interior. The introduction of the internal free convection effect decreased the calculated wing lower skin temperatures by 20 F at most, 1200 sec after touchdown. If the internal convection is treated as forced convection, the calculated wing lower skin temperatures after touchdown can be reduced to match the flight-measured data very closely. By reducing the TPS thicknesses to certain effective thickness to account for the TPs gap heating, the calculated wing lower skin temperatures prior to touchdown can be raised to agree with the flight data perfectly.

Ko, William L.↗

Catalytic surface effects on space thermal protection system during Earth entry of flights STS-2 through STS-5

An on going orbiter experiment catalytic surface effects experiment being conducted on the Space Shuttle is discussed. The catalytic surface effects experiment was peformed on four of the five flights of Columbia. Temperature time histories and distributions along the midfuselage and wing of the orbiter were used to determine the surface catalytic efficiency of the baseline high temperature reusable surface insulation. Correlation parameters are shown that allow the comparison of all flight data with predictions from the design and surface emittance decreased as a result of contaminants during the five flights of the Space Shuttle.

Stewart, D. A.↗

Data report for tests on the heat transfer effects of the 0.0175 scale Rockwell International Space Shuttle Vehicle model 22-OT in the AEDC 50 inch B wind tunnel (0H4B), volume 1

Results of wind tunnel heat transfer tests of 0.0175-scale Rockwell International Space Shuttle Vehicle configurations for orbiter alone, tank alone, and orbiter plus external tank are presented. Body flap shielding of SSME's during simulated entry was investigated. The tests were conducted at Mach 8 for thirteen Reynolds number.

Foster, T. F.↗

Data report for tests on the heat transfer effects of the 0.0175-scale Rockwell International Space Shuttle Vehicle model 22-OT in the AEDC 50-inch B wind tunnel (OH4B), volume 3

Results of wind tunnel heat transfer tests of 0.0175-scale Rockwell International Space Shuttle Vehicle configurations for orbiter alone, tank alone, and orbiter plus external tank are presented. Body flap shielding of SSME's during simulated entry was also investigated. The tests were conducted at Mach 8 for thirteen Reynolds number per foot values ranging from 0.5 million to 3.72 million.

Foster, T. F.↗

Space shuttle engineering and operations support: Study of the effects of multiple ground updates on the accuracy of the onboard state vector with IMU only navigation

There are six cases considered: (1) no updates made during the flight, (2) one ground update in the vertical components only at the first practice separation minus 15 minutes, (3) one ground update in all components at the first practice separation minus 5 minutes, (4) updates 2 and 3 applied successively, (5) Case 4 plus an update in all components at the second separation attempt minus 3 minutes, and (6) one ground update at first separation attempt minus 5 minutes and a second update at second separation minus two minutes. The mission control simulation program, GROPER, was run using as radar input a tape containing radar derived state vectors for the trajectory.

Killen, R.↗

Effect of Impact Location on the Response of Shuttle Wing Leading Edge Panel 9

The objective of this paper is to compare the results of several simulations performed to determine the worst-case location for a foam impact on the Space Shuttle wing leading edge. The simulations were performed using the commercial non-linear transient dynamic finite element code, LS-DYNA. These simulations represent the first in a series of parametric studies performed to support the selection of the worst-case impact scenario. Panel 9 was selected for this study to enable comparisons with previous simulations performed during the Columbia Accident Investigation. The projectile for this study is a 5.5-in cube of typical external tank foam weighing 0.23 lb. Seven locations spanning the panel surface were impacted with the foam cube. For each of these cases, the foam was traveling at 1000 ft/s directly aft, along the orbiter X-axis. Results compared from the parametric studies included strains, contact forces, and material energies for various simulations. The results show that the worst case impact location was on the top surface, near the apex.

Lyle, Karen H.↗

Risetime distortion of Shuttle Ku-band payload 50 MBPS data due to coaxial cable skin effects

This paper discusses distortion of digital signals generated in the Space Shuttle Ku-band communications systems. Specifically, the degradation considered is due to coaxial cables which interface data and clock from a source located in the payload bay to the KuSPA (Ku-Band Signal Processor Assembly) located in the avionics bay of the Shuttle. Due to the length (nearly 100 feet) and relatively narrow bandwidth of the cable, the clock and data waveforms are significantly affected by this transmission medium. This paper presents a closed form model that closely approximates the distortion of the waveforms measured in laboratory tests.

Schadelbauer, S.↗

An investigation of the landing characteristics of the NASA-MSC August 1969 baseline orbiter configuration in ground effect

A 0.05 scale model of the NASA-MSC August 1969 baseline shuttle craft was tested in Texas A&M University's 7- x 10-foot low speed wind tunnel facility. The purpose of the test was to determine the landing aerodynamic characteristics of the shuttle craft vehicle in ground effect and to evaluate control surface hinge moments experienced in the cruise and landing operational phases of flight. Analysis of the final data will allow evaluation of vehicle flight stability in ground effect and estimation of vehicle control surface power system requirements.

Chambliss, E. B.↗

Debris/Ice/TPS Assessment and Integrated Photographic Analysis of Shuttle Mission STS-92

A debris/ice/thermal protection system assessment and integrated photographic analysis was conducted for Shuttle mission STS-92. Debris inspections of the flight elements and launch pad were performed before and after launch. Icing conditions on the External Tank were assessed by the use of computer programs and infrared scanned data during cryogenic loading of the vehicle, followed by on-pad visual inspection. High speed photography of the launch was analyzed to identify ice/debris sources and evaluate potential vehicle damage and/or in-flight anomalies. This report documents the debris/ice/thermal protection system conditions and integrated photographic analysis of Space Shuttle mission STS-92 and the resulting effect, if any, on the Space Shuttle Program.

Katnik, Gregory N.↗

Wind tunnel test IA300 analysis and results, volume 1

The analysis and interpretation of wind tunnel pressure data from the Space Shuttle wind tunnel test IA300 are presented. The primary objective of the test was to determine the effects of the Space Shuttle Main Engine (SSME) and the Solid Rocket Booster (SRB) plumes on the integrated vehicle forebody pressure distributions, the elevon hinge moments, and wing loads. The results of this test will be combined with flight test results to form a new data base to be employed in the IVBC-3 airloads analysis. A secondary objective was to obtain solid plume data for correlation with the results of gaseous plume tests. Data from the power level portion was used in conjunction with flight base pressures to evaluate nominal power levels to be used during the investigation of changes in model attitude, eleveon deflection, and nozzle gimbal angle. The plume induced aerodynamic loads were developed for the Space Shuttle bases and forebody areas. A computer code was developed to integrate the pressure data. Using simplified geometrical models of the Space Shuttle elements and components, the pressure data were integrated to develop plume induced force and moments coefficients that can be combined with a power-off data base to develop a power-on data base.

Kelley, P. B.↗

Effect of strain isolator pad modulus on inplane strain in Shuttle Orbiter thermal protection system tiles

The thermal protection system used on the Space Shuttle orbiter to determine strains in the reusable surface insulation tiles under simulated flight loads was investigated. The effects of changes in the strain isolator pad (SIP) moduli on the strains in the tile were evaluated. To analyze the SIP/tile system, it was necessary to conduct tests to determine inplane tension and compression modulus and inplane failure strain for the densified layer of the tiles. It is shown that densification of the LI-900 tile material increases the modulus by a factor of 6 to 10 and reduces the failure strain by about 50%. It is indicated that the inplane strain levels in the Shuttle tiles in the highly loaded regions are approximately 2 orders of magnitude lower than the failure strain of the material. It is concluded that most of the LI-900 tiles on the Shuttle could be mounted on a SIP with tensile and shear stiffnesses 10 times those of the present SIP without inplane strain failure in the tile.

Sawyer, J. W.↗

BLIMPK/Streamline Surface Catalytic Heating Predictions on the Space Shuttle Orbiter

This paper describes the results of an analysis of localized catalytic heating effects to the U.S. Space Shuttle Orbiter Thermal Protection System (TPS). The analysis applies to the High-temperature Reusable Surface Insulation (HRSI) on the lower fuselage and wing acreage, as well as the critical Reinforced Carbon-Carbon on the nose cap, chin panel and the wing leading edge. The object of the analysis was to use a modified two-layer approach to predict the catalytic heating effects on the Orbiter windward HRSI tile acreage, nose cap, and wing leading edge assuming localized highly catalytic or fully catalytic surfaces. The method incorporated the Boundary Layer Integral Matrix Procedure Kinetic (BLIMPK) code with streamline inputs from viscous Navier-Stokes solutions to produce heating rates for localized fully catalytic and highly catalytic surfaces as well as for nominal partially catalytic surfaces (either Reinforced Carbon-Carbon or Reaction Cured Glass) with temperature-dependent recombination coefficients. The highly catalytic heating results showed very good correlation with Orbiter Experiments STS-2, -3, and -5 centerline and STS-5 wing flight data for the HRSI tiles. Recommended catalytic heating factors were generated for use in future Shuttle missions in the event of quick-time analysis of damaged or repaired TPS areas during atmospheric reentry. The catalytic factors are presented along the streamlines as well as a function of stagnation enthalpy so they can be used for arbitrary trajectories.

Marichalar, Jeremiah J.↗

Effects of the air breathing propulsion system on space shuttle orbiter subsonic stability and control characteristics (OA71A)

Experimental aerodynamic investigations were conducted on an 0.0405 scale representation of the -89B (2A) Space Shuttle Orbiter in a 7.75 x 11.00 ft low speed wind tunnel during the time period from July 27, 1973 to August 3, 1973. The primary test objective was to investigate the aerodynamic effects of engine nacelle grouping and location on the orbiter ferry mission configuration. Five nacelles were tested, both individually mounted as well as mounted in a podded configuration, at the baseline position and moved 45.0 in. aft (full scale). Orbiter control effectiveness, both with and without nacelles, was recorded at elevon deflections of 0 deg, 5 deg, 10 deg, -10 deg and -20 deg and aileron deflections, about 0 deg elevon, of 0 deg, 5 deg, 10 deg, and 15 deg. The model was sting mounted on a 2.5 inch diameter internal strain gage balance entering through the base region. The nominal angle of attack range was -4 deg or = alpha or = 30 deg. Yaw polars were recorded over the beta range of -10 deg or = beta or = at fixed angles of attack of 0 deg and 10 deg.

Mennell, R. C.↗