SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Passivation films for thin film batteries have been prepared and the conductivity and voltage stability window have been measured. Thin films of Li2CO3 have a large voltage stability window of 4.8V, which facilitates the use of this film as a passivation at both the lithium anode-electrolyte interface at high cathodic potentials.
Thin film, high performance electrodes which can operate in high temperature environments are necessary for many devices which use a solid electrolyte. Electrodes of rhodium-tungsten alloy have been deposited on solid electrolyte using photolytic chemical vapor deposition (PCVD). A technique for depositing electrodes and current collection grids simultaneously has been developed using the prenucleation characteristics of PCVD. This technique makes it possible to fabricate electrodes which allow vapor transport through the thin (<1 (micro)m) portions of the electrode while integral thick grid lines improve the electronic conductivity of the electrode, thus improving overall performance.
Thin films of gold and platinum have been deposited onto superpolished fused silica substrates using thermal evaporation, ion assisted deposition (IAD), and ion assisted sputtering. The influence of ion beam flux, thin film material, and deposition rate on the films microroughness have been investigated. Short range surface microroughness of the films has been examined using scanning tunneling microscopy (STM) and atomic force microscopy (AFM). Long range surface microroughness has been characterized using an angle resolved optical scatterometer. Results indicate that ion beam deposited coatings have improved microstructure over thermally evaporated films.
Several young supernova remnants, including SN 1006, emit synchrotron X-rays in narrow filaments, hereafter thin rims, along their periphery. The widths of these rims imply 50–100 μG fields in the region immediately behind the shock, far larger than expected for the interstellar medium compressed by unmodified shocks, assuming electron radiative losses limit rim widths. However, magnetic field damping could also produce thin rims. Here we review the literature on rim width calculations, summarizing the case for magnetic field amplification. We extend these calculations to include an arbitrary power-law dependence of the diffusion coefficient on energy, D ∝ Eμ. Loss-limited rim widths should shrink with increasing photon energy, while magnetic-damping models predict widths almost independent of photon energy. We use these results to analyze Chandra observations of SN 1006, in particular the southwest limb. We parameterize the FWHM in terms of energy as FWHM ∝ EmE γ. Filament widths in SN 1006 decrease with energy; mE ∼ −0.3 to −0.8, implying magnetic field amplification by factors of 10–50, above the factor of four expected in strong unmodified shocks. For SN 1006, the rapid shrinkage rules out magnetic damping models. It also favors short mean free paths (small diffusion coefficients) and strong dependence of D on energy (μ ≥ 1).
For the advanced engines in the future, knowledge of the physical parameters of aerospace components is necessary on the test stand and in flight. NASA GRC is leveraging expertise in thin films and high temperature materials to measure hot section gas and surface temperature, heat flux and static and dynamic strain. The current challenges of instrumentation technology are to further develop systems packaging and component testing of specialized sensors, further develop instrumentation techniques on complex surfaces, improve sensor durability, and to address needs for extreme temperature applications. Applications of thin film ceramic sensors as replacement for noble metals are being investigated. Technologies demonstrated in aeronautics and space applications are outlined.
Altermagnets are a newly identified family of collinear antiferromagnets with a momentum-dependent spin-split band structure of non-relativistic origin, derived from spin-group symmetry-protected crystal structures. Among candidate altermagnets, CrSb is attractive for potential applications because of a large spin-splitting near the Fermi level and a high Néel transition temperature of around 700 K. Molecular beam epitaxy is used to synthesize CrSb (0001) thin films with thicknesses ranging from 10 to 100 nm. Structural characterization, using reflection high energy electron diffraction, scanning transmission electron microscopy, and X-ray diffraction, demonstrates the growth of epitaxial films with good crystallinity. Polarized neutron reflectometry shows the absence of any net magnetization, consistent with antiferromagnetic order. In vacuo angle resolved photoemission spectroscopy (ARPES) measurements probe the band structure in a previously unexplored regime of film thickness, down to 10 nm. These ARPES measurements show a bulk-type, 3D momentum-dependent band splitting of up to 0.7 eV with g-wave symmetry, consistent with that seen in prior studies of bulk single crystals. The distinct altermagnetic band structure required for potential spin-transport applications survives down to the ∼10 nm thin film limit at room temperature.
Angstrom-scale proton-selective pores in atomically thin 2D materials present fundamentally new opportunities for advancing proton exchange membranes (PEMs). Vanadium Redox Flow Batteries (VRFBs) for grid-scale energy storage require PEMs with high areal proton conductance (>1 S cm −2 ) and minimal vanadium ion (VO 2+ ) crossover. However, state-of-the-art Nafion 212 membranes (N212 ≈50 µm thick), suffer from persistent VO 2+ crossover reducing performance and efficiency. Here, a layered PEM is demonstrated, comprising monolayer CVD graphene with Angstrom-scale proton-selective pores introduced via Ar plasma, integrated with an ultra-thin ≈300 nm polybenzimidazole (PBI) layer and sandwiched between two Nafion 211 (25 µm thick) layers. The layered architecture facilitates scalable membrane fabrication by mitigating defects while processing and facile stacking of graphene layers allows stochastic non-selective defect isolation enabling exceptionally low VO 2+ crossover (selectivity (H + areal conductance / VO 2+ permeability) ≈6709 × 10 6 S min cm −4 ), with proton conductance >8 S cm −2 . Systematic transport experiments supported by resistance-based transport modelling elucidate the role of defect size, defect isolation, and sealing, as well as layering/stacking, to enable orders of magnitude (>671× over N212) improvements in selectivity, along with areal proton conductance >8 S cm −2 . This work highlights the potential of atomic-scale proton-selective defect engineering in 2D materials, in conjunction with facile stacking and layering of materials as strategies for scalable, high-performance advances in PEMs for energy, electrochemical, and separation applications beyond VRFBs.
Control of crystal orientations in thin films of functional materials allowsedictive tuning of their strain states, electronic properties, and surface chemical reactivity. Here, conditions for orientation control in epitaxial PdO films are investigated. Due to its tetragonal structure, PdO can form two orientational relationships with the MgO (001). It is shown that, under an oxygen-rich environment provided by oxygen-plasma-assisted molecular beam epitaxy, both (00l)- and (100)-oriented PdO domains form on MgO (001). Subsequent thermal annealing in a vacuum promotes film restructuring to a predominantly (100)-oriented PdO with improved crystallinity. Ab initio calculations reveal that the (001) orientation has lower strain energy but weaker interfacial interactions and serves as an oxygen vacancy sink, whereas the (100) orientation benefits from significantly stronger MgO─PdO bonding. Consequently (100)-oriented domains become favored under oxygen-poor conditions. A mechanism is proposed whereby vacuum annealing drives orientation transformation by generating oxygen vacancies that destabilize the (001) domains and promote (100) ordering. These findings deepen the understanding of how oxygen content impacts interfacial stability and reorganization, thereby offering a route to tune domain orientations in oxide thin films.
Coherently strained NaNbO 3 thin films are synthesized across a range of thicknesses, enabling the study of size effects under epitaxial strain in antiferroelectric thin films without relaxation. Competing antiferroelectric‐ferroelectric phases are observed, leading to the stabilization of phase coexistence, multistate switching with strong retention and fatigue performance, and potential avenues to boost energy storage properties.
Metal halide perovskite photovoltaics have emerged as a high efficiency, low-cost alternative that can potentially rival or enhance conventional silicon technology. Despite exceptional initial power conversion efficiencies, achieving compliance with international standards and widespread adoption requires further enhancements to their operational stability. Notably, addressing mechanical strain and stress in brittle perovskites has emerged as a pivotal approach to mitigate chemical degradation and improve reliability during thermal cycling. Here, in this study, a popularized strain engineering strategy is investigated in which a high coefficient of thermal expansion (CTE) hole transport layer (i.e., PDCBT) is cast onto inorganic perovskite (CsPbI 2 Br) at 100 °C. Contrary to previously published results, the X-ray diffraction (XRD):Sin 2 ψ and substrate curvature measurement techniques show that the hole transport layer has no discernible impact on perovskite strain. The accuracy of the XRD:Sin 2 ψ method for measuring strain is highlighted in contrast to an analysis based on shifts of single XRD peaks which can be influenced by multiple artifacts. The findings in this study are in accordance with mechanics theory: thin layers are unable to induce significant strain changes in perovskite thin films as the force they apply is negligible compared to that applied by a thick and stiff substrate.
Abstract Thin‐ply woven composites exhibit exceptional mechanical performance by delaying the onset of damage, making them suitable for high‐performance structural applications. This study outlines the impact of manufacturing techniques (vacuum bagging and hot pressing), ply count, and fiber waviness on the mechanical properties of aromatic thermosetting copolyester/carbon‐fiber (ATSP/CF) composites. The analysis encompasses several different ply counts, evaluating their effects on the in‐plane elastic modulus (0°–90°) and tensile strength. Results demonstrate that reducing the waviness (or crimp) ratio significantly enhances the in‐plane elastic modulus, with improvements up to 188%, highlighting the importance of fiber alignment. Vacuum bagging produced ply thicknesses from 128 to 58 μm for 1–36 plies, with in‐plane elastic moduli from 30.3 to 87.2 GPa, and 4‐ and 8‐ply samples showed approximately 40% higher stiffness than those made by hot pressing. ATSP resin with high thermal stability (up to 400°C) and recyclability was used. Furthermore, this study highlights the microstructural enhancements achieved through vacuum bagging, as revealed by scanning electron and optical microscopy, and micro‐computed tomography imaging. This paper provides insights into damage mitigation and achieving enhanced mechanical properties by controlling fiber waviness using vacuum bagging and higher ply count in thin‐ply ATSP/CF composites. Highlights Crimp ratio reduction enhances elastic in‐plane elastic modulus up to 188%. Vacuum bagging increases modulus over the hot pressing manufacturing method by 40%. Lowering thickness‐per‐ply increases failure strain from 0.8% to 1.2%. Explored the performance of a novel ATSP matrix with high recyclability and thermal stability.
Niobium (Nb) films have emerged as a crucial material in the development of superconducting qubits, which are key components in quantum computing technology. Here, this review provides a comprehensive examination of Nb films from a materials perspective, focusing on their intrinsic properties, fabrication methods/techniques, and their influence on qubit performance, particularly through surface and interface driven loss mechanisms. We discuss the key material properties that are essential for qubit operation. Various deposition techniques for Nb thin films, such as sputtering, evaporation, molecular beam epitaxy, and atomic layer deposition, are explored, alongside their impact on film quality, uniformity, and qubit performance. Additionally, the influence of surface roughness, thin-film thickness, and substrate materials on quantum coherence is analyzed. Challenges such as defects and material degradation in Nb films are reviewed, along with strategies to mitigate these issues. Finally, we present the latest advancements and future directions in Nb film research, including potential improvements to enhance qubit coherence and scalability for large-scale quantum computing systems. Ultimately, a deeper understanding of surface and interface phenomena is essential for pushing the limits of qubit performance and realizing next-generation quantum technologies.
Abstract Advancing the field of photocatalysis requires the elucidation of structural properties that underpin the photocatalytic properties of promising materials. The focus of the present study is layered, Bi‐rich bismuth oxyhalides, which are widely studied for photocatalytic applications yet poorly structurally understood, due to high levels of disorder, nano‐sized domains, and the large number of structurally similar compounds. By connecting insights from multiple scattering techniques, utilizing electron‐, X‐ray‐ and neutron probes, the crystal phase of the synthesized materials is allocated as layered Bi 24 O 31 X 10 (X = Cl, Br), albeit with significant deviation from the reported 3D crystalline model. The materials comprise anisotropic platelet‐shaped crystalline domains, exhibiting significant in‐plane ordering in two dimensions but disorder and an ultra‐thin morphology in the layer stacking direction. Increased synthesis pH tailored larger, more ordered crystalline domains, leading to longer excited state lifetimes determined via femtosecond transient absorption spectroscopy (fs‐TAS). Although this likely contributes to improved photocatalytic properties, assessed via the photooxidation of benzylamine, increasing the overall surface area facilitated the most significant improvement in photocatalytic performance. This study, therefore, enabled both phase allocation and a nuanced discussion of the structure‐property relationship for complicated, ultra‐thin photocatalysts.
Group V doping in cadmium-selenide-telluride (CdSeTe) polycrystalline thin-film solar cells has demonstrated improved power conversion efficiencies (PCEs) and long-term stabilities as compared to the traditional Cu doping in the last decade. The dopants can be successfully incorporated by either in situ or ex situ doping. Here, we report that forming gas (FG) annealing enhances the efficiencies of CdSeTe polycrystalline thin-film solar cells utilizing ex situ antimony (Sb) doping via close-space sublimation of SbCl3 at ambient pressure. The FG annealing increases the hole density and carrier lifetime, reduces the back barrier height, and, therefore, leads to improved open-circuit voltages (VOCs) and fill factors (FFs). The champion device achieves a PCE of 19.2% with a VOC of 877 mV, a current density (JSC) of 30.2 mA/cm2, and an FF of 72.4%. Importantly, the Sb-doped devices showed improved stability under stress tests as compared to Cu-doped devices.
Two-dimensional (2D) nanosheets have been widely used to fabricate thin-film composite membranes for dye desalination. However, they often need to be thick to mitigate the defects resulting from their random stacking and rough support surface. Herein, bio-adhesive polydopamine (PDA) is used as a gutter layer to prepare graphene oxide (GO)-based membranes by improving the adhesion between the GO and porous support and providing a smooth surface to form thin, highly selective layers. For example, the PDA priming reduces the GO layer thickness by 57 %, from 447 to 190 nm, while achieving similar dye desalination properties. The effect of the dopamine concentration, exposure time, and GO layer thickness on the membrane structure and desalination performance are thoroughly investigated using various techniques, such as scanning electron microscopy (SEM), x-ray photoelectron spectroscopy (XPS), and x-ray diffraction (XRD). The PDA gutter layer is also applied for hollow fiber membranes, achieving water permeance of 79 L m -2 h −1 bar−1 and rejection of ∼99 % for Direct red 80. The membranes were challenged by simulated dye/salt mixtures to elucidate the complicated effect of the compositions on the desalination performance. Furthermore, this study unveils a new avenue to improve separation performance and large-scale manufacturability of 2D material-based membranes.
Understanding the mechanical and transport behavior of thin (i.e. small aperture) cracks slipping under supercritical carbon dioxide (sc-CO 2 ) conditions is essential to evaluate the integrity of sealing formations with buoyant sc-CO 2 below and the success of waterless fracturing. The two major items of interest in this work are frictional strength and permeability change of the crack. We used a triaxial cell that permits in situ visualization to conduct and monitor slippage along the faces of narrow cracks subjected to triaxial stresses. Such cracks are analogs to small geological faults. We tested carbonate-rich, 1-inch diameter Wolfcamp shale samples that are saw cut 30° to vertical to create a thin crack. Friction coefficients ranged from about 0.6 to 0.8 consistent with expectations for brittle rocks. The sc-CO 2 generally did not alter friction coefficient over the time scale of experiments. From a transport perspective, saturating cracks with sc-CO 2 substantially decreased permeability of the crack by 26%–52%, while slip resulted in a variety of permeability responses. Overall, the combined impact of sc-CO 2 saturation and slip reduced fault permeability for all tests. Our observations support the notion that the sealing capacity of some caprocks improves when saturated with sc-CO 2 and that some slip of small fractures is not necessarily detrimental to caprock integrity.
Coating polar dielectrics with thin film vanadium dioxide (VO 2 ) enables one to exploit the temperature-dependent phase transition within VO 2 to actively tune and modulate surface phonon polaritons at mid-infrared. However, controlling the behavior of such systems requires intimate knowledge of the temperature-dependent optical constants of VO 2 , which depend greatly on the growth conditions and substrate material. Here, in this work, we accurately determine the complex optical constants of VO 2 on polar dielectrics across the insulator-to-metal phase transition (IMT) using only normal incident reflectance spectra by analyzing the reflectance with Kramers–Kronig relations and thin film Fresnel equations. This non-ellipsometry technique offers an advantage in determining the refractive index using a standard infrared spectrometer.
The role of water in the growth and sintering of Ni particles over well-ordered CeOx(111) (1.5 < x < 2) thin films was investigated through scanning tunneling microscopy (STM) and X-ray photoelectron spectroscopy (XPS) studies, considering ceria-supported Ni attracts great attention as a promising catalyst for reactions such as steam reforming of ethanol and water gas shift reaction, in which water vapor is used as a key reactant. In the study, both fully oxidized CeO2 and partially reduced CeO1.75 thin films were prepared to examine the effect of the oxygen vacancies/Ce3+ sites in ceria supports. Our STM results revealed that dosing water before or after Ni deposition over the CeOx(111) surfaces at room temperature influenced the sintering behavior of Ni nanoparticles with further heating. Exposure of water to Ni nanoparticles that were deposited over both CeO2 and CeO1.75 at 300 K causes the formation of flatter particles with significantly reduced height when heating to the same temperatures compared to Ni/ceria with no water adsorbates. The flatter Ni particles were also observed when water was first dosed over CeO2 at 300 K followed by Ni deposition at room temperature and further heating. Over a partially reduced CeO1.75 surface with predosed water at 300 K, there is an extensive decrease in the particle density upon subsequent Ni deposition at room temperature and a significant increase in the height for Ni nanoparticles with further heating to higher temperatures compared to Ni over a pristine CeO1.75 surface. This is due to the filling of oxygen vacancies caused by the dissociation of water. This creates fewer nucleation sites for Ni on ceria, weakening the metal-oxide interaction and causing significant metal sintering. Our experimental findings suggest distinct adsorbate-metal-oxide interactions are key to the tuning of sintering of Ni nanoparticles over the CeOx(111) surface caused by water exposure. Such interactions are essential for the further modification of Ni-based catalysts for improved reactivity and stability.