Search NASA⌕ Search

SEARCH · Search NASA

Results for “tracking errors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

The effect of clock, media, and station location errors on Doppler measurement accuracy

Doppler tracking by the Deep Space Network (DSN) is the primary radio metric data type used by navigation to determine the orbit of a spacecraft. The accuracy normally attributed to orbits determined exclusively with Doppler data is about 0.5 microradians in geocentric angle. Recently, the Doppler measurement system has evolved to a high degree of precision primarily because of tracking at X-band frequencies (7.2 to 8.5 GHz). However, the orbit determination system has not been able to fully utilize this improved measurement accuracy because of calibration errors associated with transmission media, the location of tracking stations on the Earth's surface, the orientation of the Earth as an observing platform, and timekeeping. With the introduction of Global Positioning System (GPS) data, it may be possible to remove a significant error associated with the troposphere. In this article, the effect of various calibration errors associated with transmission media, Earth platform parameters, and clocks are examined. With the introduction of GPS calibrations, it is predicted that a Doppler tracking accuracy of 0.05 microradians is achievable.

Miller, J. K.↗

High dynamic GPS receiver using maximum likelihood estimation and frequency tracking

A new high dynamic global positioning system (GPS) receiver is presented and its performance characterized by analysis, simulation, and demonstration. The demonstration receiver is a breadboard model capable of tracking a single simulated satellite signal in pseudorange and range rate. Pseudorange and range rate estimates are made once every 20 ms, using a maximum likelihood estimator, and are tracked by means of a third-order fading memory filter in a feedback configuration. The receiver tracks pseudorange with rms errors of under 1 m when subjected to simulated 50 g, 40 g/s circular trajectories. The tracking threshold is approximately 28 dB-Hz, which provides 12 dB margin relative to the minimum specified signal strength, assuming 3.5 dB system noise figure and 0 dBi antenna gain.

Hurd, W. J.↗

Method and apparatus for receiving and tracking phase modulated signals

An apparatus and technique are described for receiving and tracking analog or digital phase modulated signals from 0 deg to 360 deg phase shift. In order to track a signal with many phases, a detector discerns the phase modulation of the incoming signal and a phase shifter generates a negative phase shift opposite in angle to the detected phase angle. This produces a converted series sideband component barrier signal. The residual carrier signal and the converted series sideband component carrier are added together to produce a tracking carrier signal. The tracking carrier signal is multiplied with the output from a voltage controlled oscillator in the tracking loop to obtain an error signal which drives the voltage controlled oscillator and tracks the incoming signal frequency. The technique is less susceptible to carrier interference which may degrade tracking and tracking may be performed at lower signal to noise ratios and for lower input signal power levels.

Villarreal, S.↗

Shuttle entry trajectory reconstruction using inflight accelerometer and gyro measurements

An error analysis has been made of a Shuttle postflight entry trajectory reconstruction process to obtain trajectory state estimation errors and to assess the impact of these errors on Shuttle aerodynamic force coefficient extraction. In this analysis, the entry trajectory is assumed to be reconstructed via numerical integration of onboard accelerometer and gyro measurements and constrained to satisfy ground-based radio tracking. The trajectory state estimation errors are calculated using a Kalman-Schmidt sequential filter assuming various measurement error models and combinations of ground-based tracking. The resultant trajectory estimation errors are analyzed in a simplified perturbation process to establish the accuracy to which postflight aerodynamic force coefficients can be determined. Results are presented which show that the principal error sources affecting the trajectory reconstruction and thus the force coefficient extraction, assuming perfect atmospheric density knowledge, are the accelerometer and gyro resolution, acceleration-sensitive gyro drifts, and the alignment uncertainties associated with integration on the Shuttle.

Compton, H. R.↗

Experimental determination of position-estimate accuracy using back-azimuth signals from a microwave landing system

Flight tests using the Boeing 737 airplane to obtain position estimates with back azimuth signals from a microwave landing system (MLS) are discussed. The equations and logic used to generate a navigation position estimate in the MLS back azimuth signal environment are described. The error in the navigation position estimate is determined. A summary of the Boeing 737 position estimate update process is described. The navigation position estimate error calculated flight data and radar tracking information is analyzed. The position estimate error data using the MLS inputs are compared with error data obtained during dual distance measuring equipment updates.

Knox, C. E.↗

Tracking-station coordinates from Geos 1 and Geos 2 optical flash data.

Center-of-mass coordinates for 28 NASA MOTS and SAO Baker-Nunn camera sites have been obtained from optical flash data from Geos 1 (1965 89A) and Geos 2 (1968 002A). More than 25,000 observations in about 100 two-day arcs were used in dynamical solutions (SAO 1969 AGU gravity model). Comparison of results with local survey solutions and with solutions from deep-space vehicle tracking suggests accuracy of about 2 meters in longitude and height and 5 meters in latitude. The relatively larger error in latitude arose from propagation of gravity-model error largely along the track of these high-inclination satellites. The results have also been compared with the solutions of the SAO 1969 standard earth for station coordinates on the North American datum. The solution obtained in the present work is much closer to the survey results in chord length between stations.

Marsh, J. G.↗

Flight Evaluation of Center-TRACON Automation System Trajectory Prediction Process

Two flight experiments (Phase 1 in October 1992 and Phase 2 in September 1994) were conducted to evaluate the accuracy of the Center-TRACON Automation System (CTAS) trajectory prediction process. The Transport Systems Research Vehicle (TSRV) Boeing 737 based at Langley Research Center flew 57 arrival trajectories that included cruise and descent segments; at the same time, descent clearance advisories from CTAS were followed. Actual trajectories of the airplane were compared with the trajectories predicted by the CTAS trajectory synthesis algorithms and airplane Flight Management System (FMS). Trajectory prediction accuracy was evaluated over several levels of cockpit automation that ranged from a conventional cockpit to performance-based FMS vertical navigation (VNAV). Error sources and their magnitudes were identified and measured from the flight data. The major source of error during these tests was found to be the predicted winds aloft used by CTAS. The most significant effect related to flight guidance was the cross-track and turn-overshoot errors associated with conventional VOR guidance. FMS lateral navigation (LNAV) guidance significantly reduced both the cross-track and turn-overshoot error. Pilot procedures and VNAV guidance were found to significantly reduce the vertical profile errors associated with atmospheric and airplane performance model errors.

Williams, David H.↗

Comparative analysis of operational forecasts versus actual weather conditions in airline flight planning, volume 2

The impact of more timely and accurate weather data on airline flight planning with the emphasis on fuel savings is studied. This volume of the report discusses the results of Task 2 of the four major tasks included in the study. Task 2 compares various catagories of flight plans and flight tracking data produced by a simulation system developed for the Federal Aviation Administrations by SRI International. (Flight tracking data simulate actual flight tracks of all aircraft operating at a given time and provide for rerouting of flights as necessary to resolve traffic conflicts.) The comparisons of flight plans on the forecast to flight plans on the verifying analysis confirm Task 1 findings that wind speeds are generally underestimated. Comparisons involving flight tracking data indicate that actual fuel burn is always higher than planned, in either direction, and even when the same weather data set is used. Since the flight tracking model output results in more diversions than is known to be the case, it was concluded that there is an error in the flight tracking algorithm.

Keitz, J. F.↗

Simulation of the Attitude Determination System for Space Station berthing dynamics research

Langley has developed a simulator of the Space Station coupled to the Space Shuttle via the Remote Manipulator System for use in evaluating handling during Station assembly. To date, evaluations of this scenario had included the Station Attitude Control System (ACS), assuming that the Station Attitude Determination System (ADS) provides perfect information on the coupled configuration. Herein, the complete Station digital autopilot (DAP) is considered including both the ADS and ACS systems. The ADS, its modelling and simulation are briefly overviewed and studies concerning the closed-loop operation of the DAP during local-coordinate, orbital attitude hold are presented. Results show that the presence of a type 0 filter in the ADS angular velocity signal processing has an adverse effect on attitude estimation because of the error in steady-state tracking of the angular velocity following reaction control jet firings. This error propagates into the attitude estimate almost linearly with time and star tracker updates are required at frequent, 3-second intervals if a .001 degree accuracy is to be maintained.

Montgomery, Raymond C.↗

Assimilation of SMAP Observations Over Land Improves the Simulation and Prediction of Tropical Cyclone Idai

This work is focused on the role of soil moisture in the prediction of tropical cyclones (TCs) approaching land and after landfall. Soil moisture conditions can impact the circulation and structure of an existing tropical cyclone (TC) when part or all of the circulation is over land. For example, dry land surface conditions may lead to faster dissipation of a TC over land (often associated with changes in precipitation structure), whereas very wet conditions may help sustain or in rare cases re-intensify a TC. Moreover, the presence of strong soil moisture gradients may affect the symmetry and development of the TC circulation leading to changes in its over-land track. While the link between soil moisture conditions and TC evolution in proximity to land is relatively well understood in theory, applications of these findings in the context of numerical weather prediction (NWP) have been limited. Here we present a case study that explores the potential of improving TC predictions through an improved soil moisture initialization in an NWP framework. Specifically, we examine the impact of assimilating observations from the NASA Soil Moisture Active Passive (SMAP) mission into the NASA Goddard Earth Observing System (GEOS) global weather model on the prediction of South-West Indian Ocean TC Idai (2019). SMAP provides accurate L-band (1.4 GHz) brightness temperatures (Tb) observations that are sensitive to soil moisture globally and at high revisit times of 2-3 days. It has previously been shown that the assimilation of SMAP Tb observations significantly improves modeled land surface states. Thus, it is expected that SMAP can be used to constrain land surface initial conditions and potentially benefit TC forecasts. Here we present two sets of retrospective forecasts of TC Idai that are compared in an Observing System Experiment framework at ¼ degree resolution: (i) forecasts initialized from an analysis that is comparable to the GEOS operational analysis (without SMAP Tb assimilation) and (ii) forecasts initialized from an analysis that additionally assimilates SMAP brightness temperature observations over land using a weakly-coupled land analysis. We find that the assimilation of SMAP meaningfully improves the representation of TC Idai’s structure as well as the prediction of its intensity and track. The analyzed TC size, as measured by the wind speed radius, is improved by up to 18% in the analysis with SMAP assimilation relative to the control run. The forecast intensity error, measured against the observed intensity, is reduced by up to 23%. At the 1/4-degree resolution used here, GEOS unavoidably under-estimates TC intensity and over-estimates TC size. The SMAP assimilation therefore corrects the model in the right direction, leading to a storm that is more energetic and more compact. Furthermore, we find that the along-track forecast error is reduced by up to 34%, indicating a more accurate propagation speed, which is consistent with the fact that TC speed over land is strongly affected by surface processes. The impact of SMAP assimilation on the forecast cross-track error is neutral. Across the TC forecast skill metrics used here, the improvements from SMAP DA are largest at lead times of 36 to 72 hours, suggesting that the predictability of forecasts at shorter lead times may be dominated by short-term convective processes, while the land and its longer memory gains in importance as a source of predictability on a 2-3 day timescale. We further investigated the underlying mechanisms leading to the skill improvements from SMAP data assimilation by isolating the land areas that directly influence TC Idai using a back trajectory analysis. We find that the assimilation of SMAP leads to wetter soil moisture conditions that cause an increased latent heat flux, which ultimately results in TC analyzed representation that has higher column-integrated total moisture content and total energy compared to the analysis in the control run without SMAP assimilation. Overall, the results highlight that the assimilation of SMAP observations into a global numerical weather prediction model can lead to pronounced improvements of TC predictions. This is a crucial step towards a better mitigation of the socio-economic impact of landfalling TCs and thus safeguarding human lives. Finally, our study presents an event-based approach that assesses the impact of land data assimilation for a particular weather event rather than by globally averaging differences in skill. We argue that global skill assessments – while necessary – can mute the impact of land data assimilation, because the land’s influence on the atmosphere is constrained to certain locations and certain times. Instead, the event-based approach better highlights the true potential of land data assimilation in the context of NWP, especially for extreme events when accurate predictions are critical.

Jana Kolassa↗

Assimilation of SMAP Observations Over Land Improves the Simulation and Prediction of Tropical Cyclone Idai

This work is focused on the role of soil moisture in the prediction of tropical cyclones (TCs) approaching land and after landfall. Soil moisture conditions can impact the circulation and structure of an existing tropical cyclone (TC) when part or all of the circulation is over land. For example, dry land surface conditions may lead to faster dissipation of a TC over land (often associated with changes in precipitation structure), whereas very wet conditions may help sustain or in rare cases re-intensify a TC. Moreover, the presence of strong soil moisture gradients may affect the symmetry and development of the TC circulation leading to changes in its over-land track. While the link between soil moisture conditions and TC evolution in proximity to land is relatively well understood in theory, applications of these findings in the context of numerical weather prediction (NWP) have been limited. Here we present a case study that explores the potential of improving TC predictions through an improved soil moisture initialization in an NWP framework. Specifically, we examine the impact of assimilating observations from the NASA Soil Moisture Active Passive (SMAP) mission into the NASA Goddard Earth Observing System (GEOS) global weather model on the prediction of South-West Indian Ocean TC Idai (2019). SMAP provides accurate L-band (1.4 GHz) brightness temperatures (Tb) observations that are sensitive to soil moisture globally and at high revisit times of 2-3 days. It has previously been shown that the assimilation of SMAP Tb observations significantly improves modeled land surface states. Thus, it is expected that SMAP can be used to constrain land surface initial conditions and potentially benefit TC forecasts. Here we present two sets of retrospective forecasts of TC Idai that are compared in an Observing System Experiment framework at ¼ degree resolution: (i) forecasts initialized from an analysis that is comparable to the GEOS operational analysis (without SMAP Tb assimilation) and (ii) forecasts initialized from an analysis that additionally assimilates SMAP brightness temperature observations over land using a weakly-coupled land analysis. We find that the assimilation of SMAP meaningfully improves the representation of TC Idai’s structure as well as the prediction of its intensity and track. The analyzed TC size, as measured by the wind speed radius, is improved by up to 18% in the analysis with SMAP assimilation relative to the control run. The forecast intensity error, measured against the observed intensity, is reduced by up to 23%. At the 1/4-degree resolution used here, GEOS unavoidably under-estimates TC intensity and over-estimates TC size. The SMAP assimilation therefore corrects the model in the right direction, leading to a storm that is more energetic and more compact. Furthermore, we find that the along-track forecast error is reduced by up to 34%, indicating a more accurate propagation speed, which is consistent with the fact that TC speed over land is strongly affected by surface processes. The impact of SMAP assimilation on the forecast cross-track error is neutral. Across the TC forecast skill metrics used here, the improvements from SMAP DA are largest at lead times of 36 to 72 hours, suggesting that the predictability of forecasts at shorter lead times may be dominated by short-term convective processes, while the land and its longer memory gains in importance as a source of predictability on a 2-3 day timescale. We further investigated the underlying mechanisms leading to the skill improvements from SMAP data assimilation by isolating the land areas that directly influence TC Idai using a back trajectory analysis. We find that the assimilation of SMAP leads to wetter soil moisture conditions that cause an increased latent heat flux, which ultimately results in TC analyzed representation that has higher column-integrated total moisture content and total energy compared to the analysis in the control run without SMAP assimilation. Overall, the results highlight that the assimilation of SMAP observations into a global numerical weather prediction model can lead to pronounced improvements of TC predictions. This is a crucial step towards a better mitigation of the socio-economic impact of landfalling TCs and thus safeguarding human lives. Finally, our study presents an event-based approach that assesses the impact of land data assimilation for a particular weather event rather than by globally averaging differences in skill. We argue that global skill assessments – while necessary – can mute the impact of land data assimilation, because the land’s influence on the atmosphere is constrained to certain locations and certain times. Instead, the event-based approach better highlights the true potential of land data assimilation in the context of NWP, especially for extreme events when accurate predictions are critical.

Jana Kolassa↗

Determination of highly accurate orbits for altimeter satellites over limited geographic areas

Accurate orbits are necessary for altimeter satellites for operational computation of sea surface heights and for the determination of any bias in the altimeter measurement. These satellites require high accuracy throughout the orbit, in general a difficult task due to gravity model, solar radiation pressure, and atmospheric drag effects. Extensive analysis has reduced such errors for Seasat only to the 50 cm level. For calibration purposes the use of such an orbit would require a very large number of tracks to reduce the error to the sub-10 cm level even if all passes had only random errors. Since altimeter calibration orbits require high accuracy only over a limited geographical area, the use of a ranging station, such as a laser tracker in the calibration area can provide the required accuracy. The Bermuda laser provided such orbits for Seasat, with satellite-station height accuracy estimated to be at the sub-3 cm level. Because the station height is accurately known, such orbits can also be used to test global orbit accuracies.

Kolenkiewicz, R.↗

GPS high dynamic receiver tracking demonstration results

Demonstration results are presented for a high dynamic GPS receiver. The receiver tested is a breadboard unit capable of tracking one simulated satellite signal in pseudorange and range rate. The receiver makes approximate maximum likelihood estimates of pseudorange and range rate each 20 ms, and tracks these observables using a third order filter with a time constant of 0.14 s. Carrier phase is not tracked, which eliminates the typical failure mode of loss of carrier lock associated with PLLs at high dynamics. The receiver tracks with pseudorange lag errors of under 0.06 m when subjected to simulated 50 g turns with 40 g/s peak jerk. Pseudorange errors due to receiver noise alone are approximately 0.6 m rms at a carrier power to noise spectral density ratio of 34 dB-Hz. The tracking threshold SNR is approximately 28 dB-Hz, which provides 12 dB margin relative to the 40 dB-Hz that occurs with minimum specified satellite signal strength, 3.5 dB system noise figure, and 0 dBi antenna gain.

Hurd, W. J.↗

Tracking and orbit determination of near earth orbiting satellites using earth synchronous relay satellites

A Tracking Data Relay Satellite System (TDRSS) made up of two earth synchronous data relay satellites is proposed for the late 1970s to aid in the tracking, or take the place of ground tracking, or near-earth orbiters. Theoretical error analysis studies were conducted to evaluate the TDRSS concept of tracking user satellites. All major factors affecting orbit determination accuracy were considered in the analysis, including tracking system and dynamic modeling errors.

Bryant, W. C., Jr.↗

VHF antenna far-field pattern measurements at 60 MHz using an outdoor antenna range for Europa Clipper mission

Improvements to measurements of a VHF folded dipole operating at 55-65 MHz to be used as part of a radar for a mission to one of Jupiter’s moons, Europa, are presented. Previous measurements using an unmanned aerial vehicle (UAV) or small unmanned aerial system (sUAS) are improved upon by reducing systematic errors and more accurately tracking distances within the measurement system on an outdoor measurement range at Jet Propulsion Laboratory (JPL). Details of the measurement system setup are presented along with a brief discussion of error sources. Comparing previously collected measurement data with the new measurements reveal an improvement of approximately 0.4 dB in accuracy with an improvement in over 1 dB for error budgets.

Decrossas, Emmanuel↗

Design, implementation and flight testing of PIF autopilots for general aviation aircraft

The designs of Proportional-Integrated-Filter (PIF) auto-pilots for a General Aviation (NAVION) aircraft are presented. The PIF autopilot uses the sampled-data regulator and command generator tracking to determine roll select, pitch select, heading select, altitude select and localizer/glideslope capture and hold autopilot modes. The PIF control law uses typical General Aviation sensors for state feedback, command error integration for command tracking, digital complementary filtering and analog prefiltering for sensor noise suppression, a control filter for computation delay accommodation and the incremental form to eliminate trim values in implementation. Theoretical developments described in detail, were needed to combine the sampled-data regulator with command generator tracking for use as a digital flight control system. The digital PIF autopilots are evaluated using closed-loop eigenvalues and linear simulations. The implementation of the PIF autopilots in a digital flight computer using a high order language (FORTRAN) is briefly described. The successful flight test results for each PIF autopilot mode is presented.

Broussard, J. R.↗