Search NASA⌕ Search

SEARCH · Search NASA

Results for “ACOUSTIC SIMULATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Reducing the Noise Impact of Small Aircraft through Indirect Trajectory Optimization

This research examined the feasibility of incorporating an acoustic metric into the optimization of an aircraft trajectory to reduce the noise experienced by an observer. The method investigated a perturbed path of an unmanned aerial system with specified boundary conditions on position and velocity while maintaining a nominal flight speed. An acoustic model based on Gutin’s work was developed to estimate propeller noise as a function of flight parameters, propulsion characteristics, and spatial location. A trajectory was then optimized a priori to reduce the noise experienced by an observer. Multiple simulations were performed and results showed that integrating an acoustic metric into the path planning process could be used to reduce the noise impact on an observer with no perturbation to the nominal flight speed.

Matthew B Galles↗
NASA NTRS1994

Chromospheric heating and metal deficiency in cool giants: Theoretical results versus observations

We compute acoustic shock wave-heated chromosphere models for moderately cool giant stars which differ greatly in metallicity. Subsequently, we simulate the emerging Mg II k lines assuming partial redistribution. The initial acoustic energy fluxes and the wave periods are taken from acoustic wave generation calculations based on traditional convection zone models. We find that the Mg II and Ca II core emissions are close to the observed basal flux limits which are common for giants and dwarfs. In addition, we find that the Mg II core emission is independent of the metallicity, in agreement with observations. We argue that these results should be considered as further evidence that the basal flux limits are indeed due to acoustic shock heating. The acoustic heating mechanism seems to be dominant in all nonmagnetic nonpulsating late-type stars.

Cuntz, M.↗
NASA NTRSDate not supplied

Update on Electric Motor Noise

Electric motors like those used in concept Advanced Air Mobility vehicles generate noise relevant to the acoustic profile of those vehicles. This work presents ongoing efforts to study, understand, and predict the noise generated by these types of motors. Efforts to perform experimental and simulation investigations of motor vibration modes are presented. Then recent acoustic measurements of operating motors and the resonant tones they generate is discussed. Lastly an update of ongoing efforts to measure real world vehicles is provided.

Electric motor noise↗
NASA NTRS1992

Scanning electron acoustic microscopy of residual stresses in ceramics - Theory and experiment

The paper presents a three-dimensional mathematical model of signal generation and contrast in brittle materials and uses the model to simulate the effect of residual stress fields on the scanning electron acoustic microscopy (SEAM)-generated electron acoustic signal. According to the model, a positive (tensile) strain produces an increase in the output signal, whereas a negative (compressive) strain produces a decrease in the ouput signal. Dark field contrast conditions occur at a chopping frequency at which V2 - V1 is greater than 0 (where V2 = V is the SEAM output in a region of residual stresses, and V1 is the output in a stress-free region of the sample). Under ideal conditions (maximum contrast) V1 approaches zero. It was found that tensile strains of the order 0.2-0.3 percent, possible in brittle materials, would produce a variation of the acoustic output signal of the order 10 nV (about 1 percent), well within the image contrast and signal processing capability of the SEAM electronics.

Cantrell, John H.↗
NASA NTRS1993

Multi-disciplinary coupling effects for integrated design of propulsion systems

Effective computational simulation procedures are described for modeling the inherent multi-disciplinary interactions which govern the accurate response of propulsion systems. Results are presented for propulsion system responses including multi-disciplinary coupling effects using coupled multi-discipline thermal, structural, and acoustic tailoring; an integrated system of multi-disciplinary simulators; coupled material behavior/fabrication process tailoring; sensitivities using a probabilistic simulator; and coupled materials, structures, fracture, and probabilistic behavior simulator. The results demonstrate that superior designs can be achieved if the analysis/tailoring methods account for the multi-disciplinary coupling effects. The coupling across disciplines can be used to develop an integrated coupled multi-discipline numerical propulsion system simulator.

Chamis, C. C.↗
NASA NTRS2002

Psychoacoustic Testing of Modulated Blade Spacing for Main Rotors

Psychoacoustic testing of simulated helicopter main rotor noise is described, and the subjective results are presented. The objective of these tests was to evaluate the potential acoustic benefits of main rotors with modulated (uneven) blade spacing. Sound simulations were prepared for six main rotor configurations. A baseline 4-blade main rotor with regular blade spacing was based on the Bell Model 427 helicopter. A 5-blade main rotor with regular spacing was designed to approximate the performance of the 427, but at reduced tipspeed. Four modulated rotors - one with "optimum" spacing and three alternate configurations - were derived from the 5 bladed regular spacing rotor. The sounds were played to 2 subjects at a time, with care being taken in the speaker selection and placement to ensure that the sounds were identical for each subject. A total of 40 subjects participated. For each rotor configuration, the listeners were asked to evaluate the sounds in terms of noisiness. The test results indicate little to no "annoyance" benefit for the modulated blade spacing. In general, the subjects preferred the sound of the 5-blade regular spaced rotor over any of the modulated ones. A conclusion is that modulated blade spacing is not a promising design feature to reduce the annoyance for helicopter main rotors.

Edwards, Bryan↗
NASA NTRS2016

Acoustic Radiation From a Mach 14 Turbulent Boundary Layer

Direct numerical simulations (DNS) are used to examine the turbulence statistics and the radiation field generated by a high-speed turbulent boundary layer with a nominal freestream Mach number of 14 and wall temperature of 0:18 times the recovery temperature. The flow conditions fall within the range of nozzle exit conditions of the Arnold Engineering Development Center (AEDC) Hypervelocity Tunnel No. 9 facility. The streamwise domain size is approximately 200 times the boundary-layer thickness at the inlet, with a useful range of Reynolds number corresponding to Re 450 􀀀 650. Consistent with previous studies of turbulent boundary layer at high Mach numbers, the weak compressibility hypothesis for turbulent boundary layers remains applicable under this flow condition and the computational results confirm the validity of both the van Driest transformation and Morkovin's scaling. The Reynolds analogy is valid at the surface; the RMS of fluctuations in the surface pressure, wall shear stress, and heat flux is 24%, 53%, and 67% of the surface mean, respectively. The magnitude and dominant frequency of pressure fluctuations are found to vary dramatically within the inner layer (z/delta 0.< or approx. 0.08 or z+ < or approx. 50). The peak of the pre-multiplied frequency spectrum of the pressure fluctuation is f(delta)/U(sub infinity) approx. 2.1 at the surface and shifts to a lower frequency of f(delta)/U(sub infinity) approx. 0.7 in the free stream where the pressure signal is predominantly acoustic. The dominant frequency of the pressure spectrum shows a significant dependence on the freestream Mach number both at the wall and in the free stream.

Zhang, Chao↗
NASA NTRS1999

Generation of Electron Suprathermal Tails in the Upper Solar Atmosphere: Implications for Coronal Heating

We present a mechanism for the generation of non-Maxwellian electron distribution function in the upper regions of the solar atmosphere in the presence of collisional damping. It is suggested that finite amplitude, low frequency, obliquely propagating electromagnetic waves can carry a substantial electric field component parallel to the mean magnetic field that can be significantly larger than the Dreicer electric field. This long wavelength electric fluctuation is capable of generating high frequency electron plasma oscillations and low frequency ion acoustic-like waves. The analysis has been performed using 1-1/2D Vlasov and PIC numerical simulations in which both electrons and ions are treated kinetically and self consistently. The simulation results indicate that high frequency electron plasma oscillations and low frequency ion acoustic-like waves are generated. The high frequency electron plasma oscillation drives electron plasma turbulence, which subsequently is damped out by the background electrons. The turbulence damping results in electron acceleration and the generation of non-Maxwellian suprathermal tails on time scales short compared to collisional damping. Bulk heating also occurs if the fluctuating parallel electric field is strong enough. This study suggests that finite amplitude, low frequency, obliquely propagating, electromagnetic waves can play a significant role in the acceleration and heating of the solar corona electrons and in the coupling of medium and small-scale phenomena.

Vinas, Adolfo F.↗
NASA NTRS2018

Subsonic Jet Noise Simulation with JENRE

JENRE, a large eddy simulation code, is used to simulate an unheated, subsonic jet. Results are compared to experiment, with an emphasis on validating the acoustic power spectral density at the farfield. Problems encountered during the development of the simulations are discussed, with solutions to said problems.

Ingraham, Daniel↗
NASA NTRS2018

Airframe Noise Simulations of a Full-Scale Aircraft

Computational results for a full-scale simulation of a Gulfstream G-III aircraft are presented. In support of a NASA airframe noise flight test campaign, Exa Corporation’s lattice Boltzmann PowerFLOW® solver was used to perform time-accurate simulations of the flow around a highly detailed, full-scale aircraft model. Free-air boundary conditions were used at a Mach number of 0.23 and a Reynolds number of 10.5 × 10(exp 6) based on mean aerodynamic chord. This paper documents the simulation campaign for the baseline aircraft configuration at several flight conditions, including multiple flap deflections and main landing gear deployed or retracted. The high-fidelity, synthetic data were post-processed using a Ffowcs-Williams and Hawkings integral approach to estimate farfield acoustic behavior, with pressures on the model solid surface or a permeable surface enveloping the acoustic near field used as input. The numerical approach, simulation attributes, and the effects of grid resolution, gear deployment, and multiple flap deflections, are discussed as well.

Appelbaum, Jason↗
NASA NTRS1989

Noise of a model counterrotation propeller with simulated fuselage and support pylon at takeoff/approach conditions

Two modern high-speed advanced counterrotation propellers, F7/A7 and F7/A3 were tested in the NASA Lewis Research Centers's 9- by 15-foot Anechoic Wind Tunnel at simulated takeoff/approach conditions of 0.2 Mach number. Both rotors were of similar diameter on the F7/A7 propeller, while the aft rotor diameter of the F7/A3 propeller was 85 percent of the forward propeller to reduce tip vortex-aft rotor interaction. The two propellers were designed for similar performance. The propellers were tested in both the clean configuration, and installed configuration consisting of a simulated upstream nacelle support pylon and fuselage section. Acoustic measurements were made with an axially translating microphone probe, and with a polar microphone probe which was fixed to the propeller nacelle and could make both sideline and circumferential acoustic surveys. Aerodynamic measurements were also made to establish propeller operating conditions. The propellers were run at blade setting angles (fron angle/rear angle) of 41.1/39.4 deg for the F7/A7 propeller, and 41.1/46.4 deg for the F7/A3 propeller. The forward rotors were tested over a range of tip speeds from 165 to 259 m/sec (540 to 850 ft/sec), and both propellers were tested at the maximum rotor-rotor spacing, based on pitch change axis separation, of 14.99 cm (5.90 in.). The data presented in this paper are for 0 deg propeller axis angle of attack. Results are presented for the baseline, pylon-alone, and strut + fuselage configurations. The presence of the simulated fuselage resulted in higher rotor-alone tone levels in a direction normal to the advancing propeller blade near the fuselage. A corresponding rotor-alone tone reduction was often observed 180 deg circumferentially from this region of increased noise. A significant rotor-alone increase for both rotors was observed diametrically opposite the fuselage. In some cases, interaction tone levels were likewise affected by the simulated installation.

Woodward, Richard P.↗
NASA NTRS1989

Noise of a model counterrotation propeller with simulated fuselage and support pylon at takeoff/approach conditions

Two modern high-speed advanced counterrotation propellers, F7/A7 and F7/A3 were tested in the NASA Lewis Research Centers's 9- by 15-foot Anechoic Wind Tunnel at simulated takeoff/approach conditions of 0.2 Mach number. Both rotors were of similar diameter on the F7/A7 propeller, while the aft rotor diameter of the F7/A3 propeller was 85 percent of the forward propeller to reduce tip vortex-aft rotor interaction. The two propellers were designed for similar performance. The propellers were tested in both the clean configuration, and installed configuration consisting of a simulated upstream nacelle support pylon and fuselage section. Acoustic measurements were made with an axially translating microphone probe, and with a polar microphone probe which was fixed to the propeller nacelle and could make both sideline and circumferential acoustic surveys. Aerodynamic measurements were also made to establish propeller operating conditions. The propellers were run at blade setting angles (front angle/rear angle) of 41.1/39.4 deg for the F7/A7 propeller, and 41.1/46.4 deg for the F7/A3 propeller. The forward rotors were tested over a range of tip speeds from 165 to 259 m/sec (540 to 850 ft/sec), and both propellers were tested at the maximum rotor-rotor spacing, based on pitch change axis separation, of 14.99 cm (5.90 in.). The data presented in this paper are for 0 deg propeller axis angle of attack. Results are presented for the baseline, pylon-alone, and strut + fuselage configurations. The presence of the simulated fuselage resulted in higher rotor-alone tone levels in a direction normal to the advancing propeller blade near the fuselage. A corresponding rotor-alone tone reduction was often observed 180 deg circumferentially from this region of increased noise. A significant rotor-alone increase for both rotors was observed diametrically opposite the fuselage. In some cases, interaction tone levels were likewise affected by the simulated installation.

Woodward, Richard P.↗
NASA NTRS1992

Investigation of the dilatational dissipation in compressible homogeneous shear flow

The dilatational dissipation rate within compressible homogeneous turbulent shear flow is studied using data from direct numerical simulations. It is found that the dilatational dissipation rate is mainly associated with large scale acoustic waves. Eddy shocklets are observed; however, they have little contribution to the average dissipation rate. A mechanism for the generation of eddy shocklets is shown to be the focusing of acoustic waves. Turbulence models for the dilatational dissipation rate are compared with data from the simulations. It is found that the formulation of Zeman used by Viegas & Rubesin to calculate a compressible mixing layer agrees well with the numerical simulation results for turbulent Mach numbers less than 0.3. However, it is also found that, for the Mach number range occurring in mixing layers, the model does not accurately represent the theory upon which it is based.

Blaisdell, G. A.↗
NASA NTRSDate not supplied

Development and Validation of an Initial Electric Motor Rotor Vibration Model

An overview of the development of a low fidelity prediction tool for electric motor rotor resonant modes and frequencies. These predictions are useful for the prediction of UAM motor noise during the design phase. Finite Element Analysis of motor rotors has led to the development of a parameterized model to predict these modes shapes. This has in turn allowed to a curve-fit based model from parametric sweeps. These curves can predict resonant frequencies and shapes for 1-5kW class motors without running a simulation.

acoustics↗
NASA NTRS2016

Direct Numerical Simulation of an Airfoil with Sand Grain Roughness on the Leading Edge

As part of a computational study of acoustic radiation due to the passage of turbulent boundary layer eddies over the trailing edge of an airfoil, the Lattice-Boltzmann method is used to perform direct numerical simulations of compressible, low Mach number flow past an NACA 0012 airfoil at zero degrees angle of attack. The chord Reynolds number of approximately 0.657 million models one of the test conditions from a previous experiment by Brooks, Pope, and Marcolini at NASA Langley Research Center. A unique feature of these simulations involves direct modeling of the sand grain roughness on the leading edge, which was used in the abovementioned experiment to trip the boundary layer to fully turbulent flow. This report documents the findings of preliminary, proof-of-concept simulations based on a narrow spanwise domain and a limited time interval. The inclusion of fully-resolved leading edge roughness in this simulation leads to significantly earlier transition than that in the absence of any roughness. The simulation data is used in conjunction with both the Ffowcs Williams-Hawkings acoustic analogy and a semi-analytical model by Roger and Moreau to predict the farfield noise. The encouraging agreement between the computed noise spectrum and that measured in the experiment indicates the potential payoff from a full-fledged numerical investigation based on the current approach. Analysis of the computed data is used to identify the required improvements to the preliminary simulations described herein.

Ribeiro, Andre F. P.↗
NASA NTRS2014

Acoustics Research of Propulsion Systems

The liftoff phase induces high acoustic loading over a broad frequency range for a launch vehicle. These external acoustic environments are used in the prediction of the internal vibration responses of the vehicle and components. Present liftoff vehicle acoustic environment prediction methods utilize stationary data from previously conducted hold-down tests to generate 1/3 octave band Sound Pressure Level (SPL) spectra. In an effort to update the accuracy and quality of liftoff acoustic loading predictions, non-stationary flight data from the Ares I-X were processed in PC-Signal in two flight phases: simulated hold-down and liftoff. In conjunction, the Prediction of Acoustic Vehicle Environments (PAVE) program was developed in MATLAB to allow for efficient predictions of sound pressure levels (SPLs) as a function of station number along the vehicle using semi-empirical methods. This consisted of generating the Dimensionless Spectrum Function (DSF) and Dimensionless Source Location (DSL) curves from the Ares I-X flight data. These are then used in the MATLAB program to generate the 1/3 octave band SPL spectra. Concluding results show major differences in SPLs between the hold-down test data and the processed Ares I-X flight data making the Ares I-X flight data more practical for future vehicle acoustic environment predictions.

Gao, Ximing↗
DOE OSTI2024

Perfectly Matched Layers and Characteristic Boundaries in Lattice Boltzmann: Accuracy vs Cost

Artificial boundary conditions (BCs) play a ubiquitous role in numerical simulations of transport phenomena in several diverse fields, such as fluid dynamics, electromagnetism, acoustics, geophysics, and many more. They are essential for accurately capturing the behavior of physical systems whenever the simulation domain is truncated for computational efficiency purposes. Ideally, an artificial BC would allow relevant information to enter or leave the computational domain without introducing artifacts or unphysical effects. Boundary conditions designed to control spurious wave reflections are referred to as nonreflective boundary conditions (NRBCs). Another approach is given by the perfectly matched layers (PMLs), in which the computational domain is extended with multiple dampening layers, where outgoing waves are absorbed exponentially in time. Here, in this work, the definition of PML is revised in the context of the lattice Boltzmann method. The impact of adopting different types of BCs at the edge of the dampening zone is evaluated and compared, in terms of both accuracy and computational costs. It is shown that for sufficiently large buffer zones, PMLs allow stable and accurate simulations even when using a simple zeroth-order extrapolation BC. Moreover, employing PMLs in combination with NRBCs potentially offers significant gains in accuracy at a modest computational overhead, provided the parameters of the BC are properly tuned to match the properties of the underlying fluid flow.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1985

Acoustic waves in the solar atmosphere. VII - Non-grey, non-LTE H(-) models

The propagation and shock formation of radiatively damped acoustic waves in the solar chromosphere are studied under the assumption that H(-) is the only absorber; the opacity is non-grey. Deviations from local thermodynamic equilibrium (LTE) are permitted. The results of numerical simulations show the depth dependence of the heating by the acoustic waves to be insensitive to the mean state of the atmosphere. After the waves have developed into shocks, their energy flux decays exponentially with a constant damping length of about 1.4 times the pressure scale height, independent of initial flux and wave period. Departures from LTE have a strong influence on the mean temperature structure in dynamical chromosphere models; this is even more pronounced in models with reduced particle density - simulating conditions in magnetic flux tubes - which show significantly increased temperatures in response to mechanical heating. When the energy dissipation of the waves is sufficiently large to dissociate most of the H(-) ions, a strong temperature rise is found that is reminiscent of the temperature structure in the transition zone between chromosphere and corona; the energy flux remaining in the waves then drives mass motions.

Schmitz, F.↗