Search NASA⌕ Search

SEARCH · Search NASA

Results for “Additive Process Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Optimal Signal Processing of Frequency-Stepped CW Radar Data

An optimal signal processing algorithm is derived for estimating the time delay and amplitude of each scatterer reflection using a frequency-stepped CW system. The channel is assumed to be composed of abrupt changes in the reflection coefficient profile. The optimization technique is intended to maximize the target range resolution achievable from any set of frequency-stepped CW radar measurements made in such an environment. The algorithm is composed of an iterative two-step procedure. First, the amplitudes of the echoes are optimized by solving an overdetermined least squares set of equations. Then, a nonlinear objective function is scanned in an organized fashion to find its global minimum. The result is a set of echo strengths and time delay estimates. Although this paper addresses the specific problem of resolving the time delay between the first two echoes, the derivation is general in the number of echoes. Performance of the optimization approach is illustrated using measured data obtained from an HP-X510 network analyzer. It is demonstrated that the optimization approach offers a significant resolution enhancement over the standard processing approach that employs an IFFT. Degradation in the performance of the algorithm due to suboptimal model order selection and the effects of additive white Gaussion noise are addressed.

Ybarra, Gary A.↗

A Geosynchronous Lidar System for Atmospheric Winds and Moisture Measurements

An observing system comprised of two lidars in geosynchronous orbit would enable the synoptic and meso-scale measurement of atmospheric winds and moisture, both of which are key first-order variables of the Earth's weather equation. Simultaneous measurement of these parameters at fast revisit rates promises large advancements in our weather prediction skills. Such capabilities would be unprecedented and yield greatly improved and finer resolution initial conditions for models, make existing costly and cumbersome measurement approaches obsolete, and obviate the use of numerical techniques needed to correct data obtained using present observing systems. Additionally, simultaneous synoptic wind and moisture observations would lead to improvements in model parameterizations, and in our knowledge of small-scale weather processes. Technology and science data product assessments are ongoing. Results will be presented during the conference.

Emmitt, G. D.↗

A Geosynchronous Lidar System for Atmospheric Winds and Moisture Measurements

An observing system comprised of two lidars in geosychronous orbit would enable the synoptic and meso-scale measurement of atmospheric winds and moisture both of which are key first-order variables of the Earth's weather equation. Simultaneous measurement of these parameters at fast revisit rates promises large advancements in our weather prediction skills. Such capabilities would be unprecedented and a) yield greatly improved and finer resolution initial conditions for models, b) make existing costly and cumbersome measurement approaches obsolete, and c) obviate the use of numerical techniques needed to correct data obtained using present observing systems. Additionally, simultaneous synoptic wind and moisture observations would lead to improvements in model parameterizations, and in our knowledge of small-scale weather processes. Technology and science data product assessments are ongoing. Results will be presented during the conference.

Emmitt, G. D.↗

Acoustic-Modal Testing of the Ares I Launch Abort System Attitude Control Motor Valve

The Attitude Control Motor (ACM) is being developed for use in the Launch Abort System (LAS) of NASA's Ares I launch vehicle. The ACM consists of a small solid rocket motor and eight actuated pintle valves that directionally allocate.thrust_- 1t.has-been- predicted-that significant unsteady. pressure.fluctuations.will.exist. inside the-valves during operation. The dominant frequencies of these oscillations correspond to the lowest several acoustic natural frequencies of the individual valves. An acoustic finite element model of the fluid volume inside the valve has been critical to the prediction of these frequencies and their associated mode shapes. This work describes an effort to experimentally validate the acoustic finite model of the valve with an acoustic modal test. The modal test involved instrumenting a flight-like valve with six microphones and then exciting the enclosed air with a loudspeaker. The loudspeaker was configured to deliver broadband noise at relatively high sound pressure levels. The aquired microphone signals were post-processed and compared to results generated from the acoustic finite element model. Initial comparisons between the test data and the model results revealed that additional model refinement was necessary. Specifically, the model was updated to implement a complex impedance boundary condition at the entrance to the valve supply tube. This boundary condition models the frequency-dependent impedance that an acoustic wave will encounter as it reaches the end of the supply tube. Upon invoking this boundary condition, significantly improved agreement between the test data and the model was realized.

Davis, R. Benjamin↗

Progress of Coating Stress Compensation of Silicon Mirrors for Lynx X-ray Telescope Mission Concept Using Thermal Oxide Patterning Method

A thermal oxide patterning method has proven to be effective for correcting coating-stress-induced distortion on flat silicon wafers. We report progress on developing this method for correcting curved silicon mirrors distorted by front-side iridium coatings. Owing to the difference in geometry, a finite element model has been established to calculate the appropriate duty cycle maps in thermal oxide hexagon patterns used for compensation. In addition, a photolithographic process, along with three-dimensional printed equipment, has been developed for creating patterns precisely on the back side of curved mirrors. The developed method has been used to recover the original surface shape of two silicon mirrors which are 100-mm long, 0.5-mm thick, having 312-mm radius of curvature, and 30 deg in azimuthal span (Wolter-I geometry). These mirrors’ front sides are sputter-coated by 20-nm iridium layers with ∼-70 N∕m integrated stress. Measurement results show that the developed method can mitigate coating-induced distortion by a factor of ∼5 in RMS height and ∼4 in RMS slope error, corresponding to ∼0.5 arc sec RMS slope error. Residual errors after correction are dominated by midfrequency ripples created during the annealing process, which will be resolved in the future. The presented method is precise and inexpensive and a potential candidate for resolving the coating stress issue for Lynx optics in the future.

x-ray↗

Advancements to Wind Tunnel Testing at the Marshall Space Flight Center Aerodynamic Research Facility by the Utilization of Additively Manufactured Models

In recent years, the Aerodynamic Research Facility (ARF) at NASA’s Marshall Space Flight Center (MSFC) has heavily utilized additive manufacturing (AM) technology for the manufacturing of models for aerodynamic testing in the 14 x 14-inch Trisonic Wind Tunnel (TWT). This process change resulted in speed and cost improvements to the design and manufacture of model parts, which has provided the capability to perform parametric tests at a rapid pace with high fidelity models that are more finely detailed than previously tested. This paper outlines the model design and fabrication workflow of the ARF and the improvements made, focusing specifically on two vehicles tested. First, identical traditionally machined and AM models of a test missile configuration were tested to isolate effects of differences in manufacturing. Second, a high-fidelity model of NASA’s Space Launch System (SLS) was tested to investigate improvements in data quality possible by utilizing AM on small-scale wind tunnel tests. This paper also discusses detailed model inspections and data comparisons that were performed to prove the reliability of data across the TWT’s entire Mach range.

Ryan C Connelly↗

A Method for Retrieving Ground Flash Fraction from Satellite Lightning Imager Data

A general theory for retrieving the fraction of ground flashes in N lightning observed by a satellite-based lightning imager is provided. An "exponential model" is applied as a physically reasonable constraint to describe the measured optical parameter distributions, and population statistics (i.e., mean, variance) are invoked to add additional constraints to the retrieval process. The retrieval itself is expressed in terms of a Bayesian inference, and the Maximum A Posteriori (MAP) solution is obtained. The approach is tested by performing simulated retrievals, and retrieval error statistics are provided. The ability to retrieve ground flash fraction has important benefits to the atmospheric chemistry community. For example, using the method to partition the existing satellite global lightning climatology into separate ground and cloud flash climatologies will improve estimates of lightning nitrogen oxides (NOx) production; this in turn will improve both regional air quality and global chemistry/climate model predictions.

Koshak, William J.↗

Reference Management Methodologies for Large Structural Models at Kennedy Space Center

There have been many challenges associated with modeling some of NASA KSC's largest structures. Given the size of the welded structures here at KSC, it was critically important to properly organize model struc.ture and carefully manage references. Additionally, because of the amount of hardware to be installed on these structures, it was very important to have a means to coordinate between different design teams and organizations, check for interferences, produce consistent drawings, and allow for simple release processes. Facing these challenges, the modeling team developed a unique reference management methodology and model fidelity methodology. This presentation will describe the techniques and methodologies that were developed for these projects. The attendees will learn about KSC's reference management and model fidelity methodologies for large structures. The attendees will understand the goals of these methodologies. The attendees will appreciate the advantages of developing a reference management methodology.

Jones, Corey↗

On the Prediction of Surface Melt Over the Greenland Ice Sheet at NWP and S2S Timescales

Greenland surface melt “events” – encompassing large swaths of the ice sheet over approximately 4-10 day periods – have occurred with increasing frequency in the 21st Century. Surface processes are significant to the ice sheet’s overall contribution to sea level. In addition, the sudden onset of widespread surface melt produces hazardous conditions for researchers and for communities adjacent to the ice sheet. The mechanisms producing melt events, their associated large-scale forcing, and timescales of interest are highly variable and poorly understood. Here we examine the predictability of melt events in a numerical weather prediction system (NWP) and a subseasonal-to-seasonal system (S2S). The NASA Global Modeling and Assimilation Office forward processing (GMAO-FP) is an NWP system that incorporates an evolving, global hybrid 4D ensemble–variational (4DEnVar) data assimilation system and a state-of-the-art model that is run twice-daily with forecasts out to five and ten days. The GMAO S2S system is a hindcast-anomaly, coupled-model prediction system initialized with an atmospheric analysis, and in situ and satellite ocean data assimilation. Both systems represent ice sheet surface hydrology and snowpack processes. We examine the performance of the systems over the period 2018-2023, a span that includes approximately nine significant events, against analyses and satellite-derived melt extent. In addition to extent, we examine related conditions and their role in the melt forecast, including the onset of both omega and Rex atmospheric blocking patterns, sea surface temperatures, sea ice extent, water vapor transport, precipitation, and surface preconditioning. We further examine the tendency for false-alarm events in each system and assess reasons for the forecast performance. North Atlantic atmospheric blocking patterns leading to surface melt are well forecast by the NWP system out to around eight days, while the S2S system generally underestimates the magnitude of such events at monthly lead times. These systems suggest that while short term forecasts of ice sheet melt and melt events are relatively robust, S2S predictions of surface conditions are highly dependent on the ability of a coupled system to generate the short-term atmospheric conditions associated with surface melt events.

Richard Cullather↗

Hydrological Modeling of the Jezero Crater Outlet-Forming Flood

Abundant evidence exists for lakes on Mars both from orbital observations [e.g., 1-3] and in situ exploration [e.g., 4-5]. These lakes can be divided into two classes: those that were hydrologically closed, so their source valley(s) terminated at the basin [3], and those that were hydrologically open, where there was sufficient flow from inlet valley(s) to cause the lake to breach and form an outlet valley [2]. It is easier to be confident from orbital data alone that a standing body of water must have existed in open basins, because there is no other way for their perched outlet valleys to form. The majority of basins fed by valley networks, rather than by isolated inlet valleys, are open [6], with some important exceptions (e.g., Gale Crater). Jezero crater (Fig. 1) is one of the most well-studied open basin paleolakes on Mars, with a breach that re-mains well above the lowest part of the crater floor, and two sedimentary fans at its northwestern margin that are likely deltaic in origin [7-9]. CRISM observations of these sediments indicate they host a variety of alteration minerals [9-11], including smectite and carbonate, and both the mineralogy of the sediments and their settings suggest they have a strong potential for preserving organic materials [10]. As a result, Jezero is a strong candidate landing site for the Mars 2020 rover. Approximate formative discharges have been estimated for its well-preserved western fan (Q approximately 500m3/s) [7], but to our knowledge, no estimates for the dis-charges associated with formation and incision of its outlet valley have been presented. Indeed, only a few studies [e.g., 12-14] have attempted to reconstruct the formation of outlet breaches broadly similar to Jezero anywhere on Mars, despite the apparent commonality of basins with large outlets [e.g., 2]. The outlet valley formed as a dam breach when the lake overflowed. In such an event, the growth and incision of the breach is directly coupled to flood discharge. In the case of Jezero, the discharge through the breach eventually lacked the energy needed to erode through the dam further, preventing complete drainage of the lake. After the initial flood, further incision can take place if additional water flows into, and thus out of, the hydrologically open lake, though the rate of this erosion occurs under more typical fluvial conditions. Despite this qualitative understanding of the process, it is useful to explore numerically what range of model parameters are potentially consistent with obser-vations of the outlet. We ultimately seek to address questions that include: (1) What was the flood hydro-graph?, (2) What sediment transport processes were involved and what can we infer about the erosion process? (3) Can most or all of the Jezero outlet's morphology be explained as a consequence of catastrophic formation, or is additional longer-term erosion required?

geology↗

Current status and future developments in radar remote sensing

Some of the major initiatives and directions of remote sensing using SAR (Synthetic Aperture Radar) data alone and in conjunction with other sensors for Earth science investigations are outlined. Specific emphasis is on areas key to global monitoring using SAR data from spaceborne platforms: calibration, geophysical processing, and generation of digital elevation models. Calibration as used here encompasses end to end system characterization over the life of a sensor and characterization of data products relative to past and future sensors. Geophysical processing is defined here to include any processing which results in derived geophysical units. An additional data type, topography, which is required to complete the three dimensional view of surface properties and correct for distortions inherent in SAR is discussed. Future challenges in radar remote sensing include development of strategies to extrapolate from regional to global scale models and development of new sensor technology.

Evans, Diane L.↗

The VIIRS Ocean Data Simulator Enhancements and Results

The VIIRS Ocean Science Team (VOST) has been developing an Ocean Data Simulator to create realistic VIIRS SDR datasets based on MODIS water-leaving radiances. The simulator is helping to assess instrument performance and scientific processing algorithms. Several changes were made in the last two years to complete the simulator and broaden its usefulness. The simulator is now fully functional and includes all sensor characteristics measured during prelaunch testing, including electronic and optical crosstalk influences, polarization sensitivity, and relative spectral response. Also included is the simulation of cloud and land radiances to make more realistic data sets and to understand their important influence on nearby ocean color data. The atmospheric tables used in the processing, including aerosol and Rayleigh reflectance coefficients, have been modeled using VIIRS relative spectral responses. The capabilities of the simulator were expanded to work in an unaggregated sample mode and to produce scans with additional samples beyond the standard scan. These features improve the capability to realistically add artifacts which act upon individual instrument samples prior to aggregation and which may originate from beyond the actual scan boundaries. The simulator was expanded to simulate all 16 M-bands and the EDR processing was improved to use these bands to make an SST product. The simulator is being used to generate global VIIRS data from and in parallel with the MODIS Aqua data stream. Studies have been conducted using the simulator to investigate the impact of instrument artifacts. This paper discusses the simulator improvements and results from the artifact impact studies.

Robinson, Wayne D.↗

Additive Manufacturing (AM) for Propulsion Component and System Applications

NASA MSFC is developing several areas of additive manufacturing (AM) for propulsion component and system applications. These developments include new AM process and material development, large-scale AM pathfinder component fabrication and hot-fire testing, AM-centric design methodology, modeling and simulation, post-processing advancements, and new design applications of AM in aerospace. Some specific areas NASA has focused is the development and commercial infusion of AM supply chain for materials such as copper-alloy GRCop (Cu-Cr-Nb), Hydrogen-resistant alloys (NASA HR-1, JBK-75), refractory-based alloys (C-103, W, Mo, new formulations), and bimetallic and multi-metallic AM processes. Additional efforts have been focused on large scale AM demonstrating complex thin-wall structures up to 60” diameter using directed energy deposition. Material characterization, properties and component hot-fire testing has been completed using many of these newly developed AM alloys/processes. NASA has also focused on improvements to post-processing including powder removal, surface enhancements, and support removal to further realize cost and schedule benefits to the overall supply chain. These developments are part of the NASA Rapid Analysis and Manufacturing Propulsion Technology (RAMPT), Low Cost Upper Stage Propulsion (LCUSP) and Long Life Additive Manufacturing (LLAMA) projects, in addition to internal IRAD, and external collaborations.

Additive Manufacturing↗

Comparison of Two Community Noise Models Applied to a NASA Urban Air Mobility Concept Vehicle

Predictions of community noise exposure from a NASA urban air mobility (UAM) concept vehicle have been conducted for representative operations using the FAA Aviation Environmental Design Tool (AEDT) in order to demonstrate modeling tool interoperability and assess applicability, capabilities and limitations of integrated noise modeling tools. To both quantify limitations and highlight other capabilities, a comparative analysis is performed using a time-domain simulation method, in particular, using the Volpe Advanced Acoustic Model (AAM). Using the same source noise model, the 3D directivity of a UAM concept vehicle is predicted in terms of aeroacoustic pressure time histories at a sphere of observer positions near the vehicle. In addition to distilling those data to a set of noise-power-distance data for input to AEDT, the data are processed preserving spectral directivity, into one-third and one-twelfth octave bands for input to AAM. Results from AEDT and AAM modeling are provided for a variety of metrics to demonstrate the effect that source noise directivity and propagation modeling fidelity have on predicted results at receptors over a study area.

urban air mobility↗

Comparison of Two Community Noise Models Applied to a NASA Urban Air Mobility Concept Vehicle

Predictions of community noise exposure from a NASA urban air mobility (UAM) concept vehicle have been conducted for representative operations using the FAA Aviation Environmental Design Tool (AEDT) in order to demonstrate modeling tool interoperability and assess applicability, capabilities and limitations of integrated noise modeling tools. To both quantify limitations and highlight other capabilities, a comparative analysis is performed using a time-domain simulation method, in particular, using the Volpe Advanced Acoustic Model (AAM). Using the same source noise model, the 3D directivity of a UAM concept vehicle is predicted in terms of aeroacoustic pressure time histories at a sphere of observer positions near the vehicle. In addition to distilling those data to a set of noise-power-distance data for input to AEDT, the data are processed preserving spectral directivity, into one-third and one-twelfth octave bands for input to AAM. Results from AEDT and AAM modeling are provided for a variety of metrics to demonstrate the effect that source noise directivity and propagation modeling fidelity have on predicted results at receptors over a study area.

urban air mobility↗

Climate Data Guide - Modern Era Retrospective Analysis for Research and Applications, version 2 (MERRA-2)

The Modern-Era Retrospective analysis for Research and Applications, version 2 (MERRA-2) is a global atmospheric reanalysis produced by the NASA Global Modeling and Assimilation Office (GMAO). It spans the satellite observing era from 1980 to the present. The goals of MERRA-2 are to provide a regularly-gridded, homogeneous record of the global atmosphere, and to incorporate additional aspects of the climate system including trace gas constituents (stratospheric ozone), and improved land surface representation, and cryospheric processes. MERRA-2 is also the first satellite-era global reanalysis to assimilate space-based observations of aerosols and represent their interactions with other physical processes in the climate system. The inclusion of these additional components are consistent with the overall objectives of an Integrated Earth System Analysis (IESA). MERRA-2 is intended to replace the original MERRA product, and reflects recent advances in atmospheric modeling and data assimilation. Modern hyperspectral radiance and microwave observations, along with GPS-Radio Occultation and NASA ozone datasets are now assimilated in MERRA-2. Much of the structure of the data files remains the same in MERRA-2. While the original MERRA data format was HDF-EOS, the MERRA-2 supplied binary data format is now NetCDF4 (with lossy compression to save space).

MERRA-2↗

Speech Acquisition and Automatic Speech Recognition for Integrated Spacesuit Audio Systems

A voice-command human-machine interface system has been developed for spacesuit extravehicular activity (EVA) missions. A multichannel acoustic signal processing method has been created for distant speech acquisition in noisy and reverberant environments. This technology reduces noise by exploiting differences in the statistical nature of signal (i.e., speech) and noise that exists in the spatial and temporal domains. As a result, the automatic speech recognition (ASR) accuracy can be improved to the level at which crewmembers would find the speech interface useful. The developed speech human/machine interface will enable both crewmember usability and operational efficiency. It can enjoy a fast rate of data/text entry, small overall size, and can be lightweight. In addition, this design will free the hands and eyes of a suited crewmember. The system components and steps include beam forming/multi-channel noise reduction, single-channel noise reduction, speech feature extraction, feature transformation and normalization, feature compression, model adaption, ASR HMM (Hidden Markov Model) training, and ASR decoding. A state-of-the-art phoneme recognizer can obtain an accuracy rate of 65 percent when the training and testing data are free of noise. When it is used in spacesuits, the rate drops to about 33 percent. With the developed microphone array speech-processing technologies, the performance is improved and the phoneme recognition accuracy rate rises to 44 percent. The recognizer can be further improved by combining the microphone array and HMM model adaptation techniques and using speech samples collected from inside spacesuits. In addition, arithmetic complexity models for the major HMMbased ASR components were developed. They can help real-time ASR system designers select proper tasks when in the face of constraints in computational resources.

Huang, Yiteng↗

The Evolution of the Impact Evidence Library Methods – What We Learned

During fiscal years 2020-2022 NASA’s Human Research Program, Exploration Medical Capability Element has worked to source this evidence for the model. During the process several lessons learned have been identified and drive recommendations for future efforts. The ICL 1.0: Spaceflight Medical Operational expertise should be consulted regarding the addition of future conditions. A clinician experienced with the nuances of spaceflight is recommended to have a minimum of 20 hours per condition to adequately source the evidence. Condition definitions should be carefully crafted to maintain mutual exclusivity. Common side effects from medications, common and consequential incidental findings in laboratory studies, and consequential side effects of diagnostic and procedural capabilities should be considered for inclusion as unique conditions in future iterations of the ICL 1.0. Incidence: Spaceflight incidence, although based on small population sizes, is the gold standard. Terrestrial incidence should be applied cautiously. Probability of minor vs. severe cases of the condition: Data informing severity probability of the medical condition are nearly always terrestrial. Special attention should be paid to this metric as it drives outcomes in the model and terrestrial data often overestimate severity of expected cases in spaceflight. Condition duration: Three clinical phases currently exist in the model. They represent the time necessary for diagnosis, treatment/convalescence/recurrence, and the remaining duration of the mission after maximal recovery, respectively. Further subdivision of acute and convalescent treatment/recurrence is recommended. Probability of need for evacuation: Surrogates for “Return to Definitive Care” were chosen prior to data collection. In most cases these surrogates were “need for hospitalization” or “need for surgery.” For many conditions these may not be realistic drivers of “Return to Definitive Care” and should be re-examined. Probability of Crew Mortality: Terrestrial mortality data is difficult to apply to astronauts who, invariably, have less comorbidities than terrestrial subjects. It must be applied judiciously. The proportion of mission tasks impaired by the condition: “Task Impairment” was assigned to each condition prior to the condition duration data becoming available. Future efforts should assign Task Impairment as the final step in sourcing the evidence.

A.J. Kreykes↗