Results for “Advanced propellants” — Page 27

NASA NTRS1987

Structureborne noise control in advanced turboprop aircraft

Structureborne noise is discussed as a contributor to propeller aircraft interior noise levels that are nonresponsive to the application of a generous amount of cabin sidewall acoustic treatment. High structureborne noise levels may jeopardize passenger acceptance of the fuel-efficient high-speed propeller transport aircraft designed for cruise at Mach 0.65 to 0.85. These single-rotation tractor and counter-rotation tractor and pusher propulsion systems will consume 15 to 30 percent less fuel than advanced turbofan systems. Structureborne noise detection methodologies and the importance of development of a structureborne noise sensor are discussed. A structureborne noise generation mechanism is described in which the periodic components or propeller swirl produce periodic torques and forces on downstream wings and airfoils that are propagated to the cabin interior as noise. Three concepts for controlling structureborne noise are presented: (1) a stator row swirl remover, (2) selection of a proper combination of blade numbers in the rotor/stator system of a single-rotation propeller, and the rotor/rotor system of a counter-rotation propeller, and (3) a tuned mechanical absorber.

Loeffler, Irvin J.↗

NASA NTRS1987

Structureborne noise control in advanced turboprop aircraft

Structureborne noise is discussed as a contributor to propeller aircraft interior noise levels that are nonresponsive to the application of a generous amount of cabin sidewall acoustic treatment. High structureborne noise levels may jeopardize passenger acceptance of the fuel-efficient high-speed propeller transport aircraft designed for cruise at Mach 0.65 to 0.85. These single-rotation tractor and counter-rotation tractor and pusher propulsion systems will consume 15 to 30 percent less fuel than advanced turbofan systems. Structureborne noise detection methodologies and the importance of development of a structureborne noise sensor are discussed. A structureborne noise generation mechanism is described in which the periodic components or propeller swirl produce periodic torques and forces on downstream wings and airfoils that are propagated to the cabin interior as noise. Three concepts for controlling structureborne noise are presented: (1) a stator row swirl remover, (2) selection of a proper combination of blade numbers in the rotor/stator system of a single-rotation propeller, and the rotor/rotor system of a counter-rotation propeller, and (3) a tuned mechanical absorber.

Loeffler, Irvin J.↗

NASA NTRS1967

Low-thrust propulsion for the MORL.

Advanced low thrust propulsion systems and propellants evaluation for stationkeeping and stability control of NASA Manned Orbital Research Laboratory

STABILITY AND CONTROL↗

NASA NTRS1972

Continuing development of the short-pulsed ablative space propulsion system.

Major advancements have been made in solid propellant pulsed plasma propulsion technology. A LES-6 microthruster has operated for 8900 hours in orbit. Millipound thrustors have been developed and tested at performance levels of as low as 112 watts/mlb. Efficiencies of up to 50% and specific impulse values up to 5000 sec have been measured. An improved microthrustor has operated at 207 watts/mlb continuously for 1440 hours. Correlations of design and performance data exist to allow thrustors to be built to meet a particular level of performance.

Palumbo, D. J.↗

NASA NTRS1980

Small Transport Aircraft Technology

The article surveys the results of the NASA-instituted Small Transport Aircraft Technology (STAT) research effort aimed at generating advanced technologies for application to new small, short haul transports having significantly better performance, efficiency, and environmental compatibility. Discussion covers fuselage designs and bonded aluminum-honeycomb wing construction which reduces the number of parts and fasteners, and gives a smoother outer contour. Topics discussed include: advanced aluminum alloys, composite primary structures, propellers, engine components, icing protection, avionics, flight controls, aerodynamics, and gust load alleviation.

Galloway, T. L.↗

NASA NTRS1983

Comparison of advanced turboprop and turbofan airplanes

Results of a parametric study to determine the effects of design variables and penalties on the fuel efficiency of Mach 0.8, 125-passenger, advanced turboprop airplanes show that propeller-wing interference penalty has a major effect. Propeller tip speed has a minor effect, and could be decreased to alleviate the noise problem without significant effects on fuel efficiency. The anticipated noise levels produced by the propfan will require additional acoustical treatment for the fuselage; this additional weight can have a significant effect on fuel efficiency. The propfan advantage over an equivalent technology turbofan is strongly dependent on the interference penalty and acoustical treatment weight. Lowering the cruise Mach number to around 0.73 would result in greatly increased fuel efficiency.

Johnson, V. S.↗

NASA NTRS1983

Parametric study of factors affecting the fuel efficiency of advanced turboprop airplanes

Results of a parametric study to determine the effects of design variables and penalties on the fuel efficiency of Mach 0.8, 125-passenger, advanced turboprop airplanes show that propeller-wing interference penalty has a major effect. Propeller tip speed has a minor effect, and could be decreased to alleviate the noise problem without significant effects on fuel efficiency. The anticipated noise levels produced by the propfan will require additional acoustical treatment for the fuselage; this additional weight can have a significant effect on fuel efficiency. The propfan advantage over an equivalent technology turbofan is strongly dependent on the interference penalty and acoustical treatment weight. Lowering the cruise Mach number to around 0.73 would result in greatly increased fuel efficiency.

Johnson, V. S.↗

NASA NTRS1984

Predicted changes in advanced turboprop noise with shaft angle of attack

Advanced turboprop blade designs and new propeller installation schemes motivated an effort to include unsteady loading effects in existing propeller noise prediction computer programs. The present work validates the prediction capability while studing the effects of shaft inclination on the radiated sound field. Classical methods of propeller performance analysis supply the time-dependent blade loading needed to calculate noise. Polar plots of the sound pressure level (SPL) of the first four harmonics and overall SPL are indicative of the change in directivity pattern as a function of propeller angle of attack. Noise predictions are compared with newly available wind tunnel data and the accuracy and applicability of the prediction method are discussed. It is concluded that unsteady blade loading caused by inclining the propeller with respect to the flow changes the directionality and the intensity of the radiated noise. These changes are well modeled by the present quasi-steady prediction method.

Padula, S. L.↗

NASA NTRS1987

Off-design analysis of counter-rotating propeller configurations

An analysis is conducted to determine whether the counterrotating propeller configuration maintains, and perhaps improves, its excellent performance in the off-design mode for the constant-speed or variable-pitch case. While the twist distribution is maintained, the blade angle is changed to absorb shaft horsepower as a constant rpm setting is maintained under varying freestream velocities. A relatively flat propeller efficiency curve is obtained for advance ratios of 1.5-5.0.

Korkan, K. D.↗

NASA NTRS1989

Synchronous critical speed tracking in hydrostatic bearing supported rotors

Hydrostatic bearings used in advanced turbopump designs use the pumped propellant as the working fluid and supply the propellant to the bearing from pump discharge. The resulting rotordynamic coefficients are highly speed-dependent and in some instances can cause system natural frequencies to coincide with spin speed over a wide speed range. This paper discusses this 'synchronous tracking' phenomenon. The factors affecting it are defined, and specific examples are presented. Methods which identify synchronous tracking issues early in the design process are reported, and techniques for eliminating this undesirable characteristic are addressed.

Henderson, Thomas W.↗

NASA NTRS1987

Large-scale Advanced Prop-fan (LAP) static rotor test report

Discussed is Static Rotor Testing of the SR-7L Large Scale Advanced Prop-Fan (LAP). The LAP is an advanced 9 foot diameter, 8 bladed propeller designed and built by Hamilton Standard under contract to the NASA Lewis Research Center. The Prop-Fan employs thin swept blades to provide efficient propulsion at flight speeds up to Mach .85. Static Testing was conducted on a 10,000 HP whirl rig at Wright Patterson Air Force Base. The test objectives were to investigate the Prop-Fan static aerodynamic and structural dynamic performance, determine the blade steady state stressers and deflections and to measure steady and unsteady pressures on the SR-7L blade surface. The measured performance of the LAP correlated well with analytical predictions at blade pitch angles below 30 deg. A stall buffet phenomenon was observed at blade pitch angles above 30 deg. This phenomenon manifested itself by elevated blade vibratory stress levels and lower than expected thrust produced and power absorbed by the Prop-Fan for a given speed and blade angle.

Degeorge, Charles L.↗

NASA NTRS1990

FAA/NASA En Route Noise Symposium

Aircraft community noise annoyance is traditionally a concern only in localities near airports. The proposed introduction of large commercial airplanes with advanced turboprop propulsion systems with supersonic propellers has given rise to concerns of noise annoyance in areas previously considered not to be impacted by aircraft noise. A symposium was held to assess the current knowledge of factors important to the impact of en route noise and to aid in the formulation of FAA and NASA programs in the area. Papers were invited on human response to aircraft noise in areas with low ambient noise levels, aircraft noise heard indoors and outdoors, aircraft noise in recreational areas, detection of propeller and jet aircraft noise, and methodological issues relevant to the design of future studies.

Powell, Clemans A.↗

NASA NTRS1990

Laser-boosted lightcraft technology demonstrator

The detailed description and performance analysis of a 1.4 meter diameter Lightcraft Technology Demonstator (LTD) is presented. The launch system employs a 100 MW-class ground-based laser to transmit power directly to an advanced combined-cycle engine that propels the 120 kg LTD to orbit - with a mass ratio of two. The single-stage-to-orbit (SSTO) LTD machine then becomes an autonomous sensor satellite that can deliver precise, high quality information typical of today's large orbital platforms. The dominant motivation behind this study is to provide an example of how laser propulsion and its low launch costs can induce a comparable order-of-magnitude reduction in sensor satellite packaging costs. The issue is simply one of production technology for future, survivable SSTO aerospace vehicles that intimately share both laser propulsion engine and satellite functional hardware.

Richard, J. C.↗

NASA NTRS1944

The Theory of Propellers III : the Slipstream Contraction with Numerical Values for Two-Blade and Four-Blade Propellers

As the conditions of the ultimate wake are concerned both theoretically and practically, the magnitude of the slipstream contraction has been calculated. It will be noted that the contraction in a representative case is of the order of only 1 percent of the propeller diameter. In consequence, all calculations need involve only first-order effects. Curves and tables are given for the contraction coefficient of two-blade and four-blade propellers for various values of the advance ratio; the contraction coefficient is defined as the contraction in the diameter of the wake helix in terms of the wake diameter at infinity. The contour lines of the wake helix are also shown at four values of the advance ratio in comparison with the contour lines for an infinite number of blades.

Theodorsen, Theodore↗

NASA NTRS1989

Laser-boosted lightcraft technology demonstrator

The ultimate goal for this NASA/USRA-sponsored 'Apollo Lightcraft Project' is to develop a revolutionary manned launch vehicle technology that can potentially reduce payload transport costs by a factor of 1000 below the space shuttle orbiter. The Rensellaer design team proposes to utilize advanced, highly energetic, beamed-energy sources (laser, microwave) and innovative combined-cycle (airbreathing/rocket) engines to accomplish this goal. This year's effort, the detailed description and performance analysis of an unmanned 1.4-m Lightcraft Technology Demonstrator (LTD) drone, is presented. The novel launch system employs a 100-MW-class ground-based laser to transmit power directly to an advanced combined-cycle engine that propels the 120-kg LTD to orbit, with a mass ratio of two. The single-stage-to-orbit (SSTO) LTD machine then becomes an autonomous sensor satellite that can deliver precise, high-quality information typical of today's large orbital platforms. The dominant motivation behind this study is to provide an example of how laser propulsion and its low launch costs can induce a comparable order-of-magnitude reduction in sensor satellite packaging costs. The issue is simply one of production technology for future, survivable SSTO aerospace vehicles that intimately share both laser propulsion engine and satellite functional hardware. A mass production cost goal of 10(exp 3)/kg for the LTD vehicle is probably realizable.

Antonison, M.↗

NASA NTRS1994

A review of 50 years of aerodynamic research with NACA/NASA

Continuous improvements in flight systems have occurred over the past 50 years due, in part, to continuous improvements in aerodynamic research techniques and capabilities. This paper traces that research from the first-hand perspective of the author who, beginning in 1944, has taken part in the NACA/NASA aerodynamic research effort through studies in low-speed wind tunnels, high-speed subsonic tunnels, transonic tunnels, supersonic tunnels, and hypersonic tunnels. New problems were found as systems advanced from low-speed propeller-driven designs to more sophisticated high-speed jet- and rocket-propelled designs. The paper reviews some of these problems and reflects on some of the solutions that have been developed in the course of various aerodynamic research programs in the past. Some of the factors, both technical and nontechnical, that have influenced the aerodynamic design, research, and development of various flight systems will be mentioned.

Spearman, M. Leroy↗

NASA NTRS1992

High performance storable propellant resistojet

From 1965 until 1985 resistojets were used for a limited number of space missions. Capability increased in stages from an initial application using a 90 W gN2 thruster operating at 123 sec specific impulse (Isp) to a 830 W N2H4 thruster operating at 305 sec Isp. Prior to 1985 fewer than 100 resistojets were known to have been deployed on spacecraft. Building on this base NASA embarked upon the High Performance Storable Propellant Resistojet (HPSPR) program to significantly advance the resistojet state-of-the-art. Higher performance thrusters promised to increase the market demand for resistojets and enable space missions requiring higher performance. During the program three resistojets were fabricated and tested. High temperature wire and coupon materials tests were completed. A life test was conducted on an advanced gas generator.

Vaughan, C. E.↗

NASA NTRS2002

A Pilot Computer-Aided Design and Manufacturing Curriculum that Promotes Engineering

Elizabeth City State University (ECSU) is located in a community that is mostly rural in nature. The area is economically deprived when compared to the rest of the state. Many businesses lack the computerized equipment and skills needed to propel upward in today's technologically advanced society. This project will close the ever-widening gap between advantaged and disadvantaged workers as well as increase their participation with industry, NASA and/or other governmental agencies. Everyone recognizes computer technology as the catalyst for advances in design, prototyping, and manufacturing or the art of machining. Unprecedented quality control and cost-efficiency improvements are recognized through the use of computer technology. This technology has changed the manufacturing industry with advanced high-tech capabilities needed by NASA. With the ever-widening digital divide, we must continue to provide computer technology to those who are socio-economically disadvantaged.

Source record↗