Results for “Application Tests” — Page 27

NASA NTRS2019

Investigating Additively Manufactured 17-4 PH for Structural Applications

17-4 is used regularly to manufacture force transducers particularly for wind tunnel testing. Such applications place demanding structural requirements on the transducers with static safety factors of 1.5 common and the potential for additional dynamic loads. Additive manufacturing (AM) of transducers is very appealing because of significant potential cost and time savings as well as increased design flexibility. This study looks at the processing of 17-4 powder using selective laser melting by two different facilities using their own best practices. Hot isostatic pressing (HIP) is used by both facilities as part of the thermomechanical processing following printing to explore whether it can improve the consistency of mechanical properties. Results revealed that HIP reduced average porosity of 17-4 parts and that the yield strength of parts following solutionization and aging met wrought material property targets. Strain to failure of one of the facilities parts was less than 5% compared to greater than 9% for the other facility. Inspection of failure surfaces revealed this discrepancy could be attributed to pores (2-4% area fraction) on the failure surface of the low ductility parts. Phase content varied between the facilities with one facility producing fully martensitic parts and the other containing some retained austenite. The phase content of the starting powder and a slower than air cooling rate following the final heat treatment above the austenite eutectoid temperature are likely sources of the retained austenite. Taken together these results suggest that the current state of the art in AM 17-4 processing is sufficient for many NASA force measurement applications, but that attention is required at each stage of processing to assure desired mechanical properties.

Burns, Devin E.↗

NASA NTRS1992

Digital time series analysis for flutter test data

An application of digital time series analysis to flutter test data processing was conducted. A numerical investigation was used to evaluate the method, as well as its sensitivity to noise and parameter variations. These parameters included those involved with data acquisition, as well as system response characteristics. This digital time series method was then used to predict flutter speed from subcritical response wind tunnel tests. Flutter speeds predicted from forced response, subcritical wind tunnel tests were compared to the experimental flutter speeds.

Batill, S. M.↗

NASA NTRS1984

Equivalent electron fluence for space qualification of shallow junction heteroface GaAs solar cells

It is desirable to perform qualification tests prior to deployment of solar cells in space power applications. Such test procedures are complicated by the complex mixture of differing radiation components in space which are difficult to simulate in ground test facilities. Although it has been shown that an equivalent electron fluence ratio cannot be uniquely defined for monoenergetic proton exposure of GaAs shallow junction cells, an equivalent electron fluence test can be defined for common spectral components of protons found in space. Equivalent electron fluence levels for the geosynchronous environment are presented.

Wilson, J. W.↗

NASA NTRS1986

Development and evaluation of a fault-tolerant multiprocessor (FTMP) computer

The design, development, and testing of FTMP hardware and software for use in advanced NASA vehicles are described in three previously published reports prepared for NASA. Consideration is given to the overall FTMP architecture; the system bus; the regional design and operation of processor, slave, clock-generation, and power systems; and the FTMP executive, facilities, acceptance-test/diagnostic, applications, and support softwar. Also included are a summary of test procedures and results and an executive summary characterizing the system, the reliability and availability models, and the overall performance.

Smith, T. B., III↗

NASA NTRS1989

The measurement of boundary layers on a compressor blade in cascade. Volume 1: Experimental technique, analysis and results

Measurements were made of the boundary layers and wakes about a highly loaded, double-circular-arc compressor blade in cascade. These laser Doppler velocimetry measurements have yielded a very detailed and precise data base with which to test the application of viscous computational codes to turbomachinery. In order to test the computational codes at off-design conditions, the data were acquired at a chord Reynolds number of 500,000 and at three incidence angles. Moreover, these measurements have supplied some physical insight into these very complex flows. Although some natural transition is evident, laminar boundary layers usually detach and subsequently reattach as either fully or intermittently turbulent boundary layers. These transitional separation bubbles play an important role in the development of most of the boundary layers and wakes measured in this cascade and the modeling or computing of these bubbles should prove to be the key aspect in computing the entire cascade flow field. In addition, the nonequilibrium turbulent boundary layers on these highly loaded blades always have some region of separation near the trailing edge of the suction surface. These separated flows, as well as the subsequent near wakes, show no similarity and should prove to be a challenging test for the viscous computational codes.

Zierke, William C.↗

NASA NTRS1989

The measurement of boundary layers on a compressor blade in cascade. Volume 2: Data tables

Measurements were made of the boundary layers and wakes about a highly loaded, double-circular-arc compressor blade in cascade. These laser Doppler velocimetry measurements have yielded a very detailed and precise data base with which to test the application of viscous computational codes to turbomachinery. In order to test the computational codes at off-design conditions, the data have been acquired at a chord Reynolds number of 500,000 and at three incidence angles. Average values and 95 percent confidence bands were tabularized for the velocity, local turbulence intensity, skewness, kurtosis, and percent backflow. Tables also exist for the blade static-pressure distributions and boundary layer velocity profiles reconstructed to account for the normal pressure gradient.

Zierke, William C.↗

NASA NTRS1995

Perspective on thermal barrier coatings for industrial gas turbine applications

Thermal Barrier Coatings (TBC's) have been used in high thrust aircraft engines for many years, and have proved to be very effective in allowing higher turbine inlet temperatures. TBC life requirements for aircraft engines are typically less than those required in industrial gas turbines. The use of TBC's for industrial gas turbines can increase if durability and longer service life can be successfully demonstrated. This paper will describe current and future applications of TBC's in industrial gas turbine engines. Early testing and applications of TBC's will also be reviewed. This paper focuses on the key factors that are expected to influence utilization of TBC's in advanced industrial gas turbine engines. It is anticipated that reliable, durable and high effective coating systems will be produced that will ultimately improve engine efficiency and performance.

Mutasim, Z. Z.↗

NASA NTRS1995

Perspective on thermal barrier coatings for industrial gas turbine applications

Thermal barrier coatings (TBC's) have been used in high thrust aircraft engines for many years, and have proved to be very effective in providing thermal protection and increasing engine efficiencies. TBC life requirements for aircraft engines are typically less than those required for industrial gas turbines. This paper describes current and future applications of TBC's in industrial gas turbine engines. Early testing and applications of TBC's is reviewed. Areas of concern from the engine designer's and materials engineer's perspective are identified and evaluated. This paper focuses on the key factors that are expected to influence utilization of TBC's in advanced industrial gas turbine engines. It is anticipated that reliable, durable and highly effective coating systems will be produced that will ultimately improve engine efficiency and performance.

Mutasim, Zaher↗

NASA NTRS1975

Design and test status for life support applications of SPE oxygen generation systems

An advanced six-man rated oxygen generation system has been fabricated and tested as part of a NASA/JSC technology development program for a long lived, manned spacecraft life support system. Details of the design and tests results are presented. The system is based on the Solid Polymer Electrolyte (SPE) water electrolysis technology and its nominal operating conditions are 2760 kN/sq m (400 psia) and 355 K (180 F) with an electrolysis module current density capability up to 350 mA/sq cm (326 ASF). The system is centered on a 13-cell SPE water electrolysis module having a single cell active area of 214 sq cm (33 sq in) and it incorporates instrumentation and controls for single pushbutton automatic startup/shutdown, component fault detection and isolation, and self-contained sensors and controls for automatic safe emergency shutdown. The system has been tested in both the orbital cyclic and continuous mode of operation. Various parametric tests have been completed to define the system capability for potential application in spacecraft environmental systems.

Titterington, W. A.↗

NASA NTRS1974

Method of boundary testing of the electric circuits and its application for calculating electric tolerances

Boundary testing of electric circuits includes preliminary and limiting tests. Preliminary tests permit determination of the critical parameters causing the greatest deviation of the output parameter of the system. The boundary tests offer the possibility of determining the limits of the fitness of the system with simultaneous variation of its critical parameters.

Redkina, N. P.↗

NASA NTRS1988

Application of intelligent systems to wind tunnel test facilities

An approach to the application of intelligent-systems technology to the wind tunnel facilities at NASA Ames Research Center is outlined. To help fulfill the long-range goals of improving data quality and increasing personnel efficiency and management effectiveness, three major areas of intelligent systems application are recommended. The available state-of-the-art technology for developing the proposed systems is reviewed including the application of commercial software packages. The initial tasks and effort to develop these systems are recommended. A prototype expert system for selection of internal strain-gage balances has been built and is presented herein as an example model for the future systems.

Lo, Ching F.↗

NASA NTRS1994

Tests Of A Magnetic Bearing For Cryogenic Applications

Report describes experiments performed in test rig on hybrid magnetic bearing for possible use in turbopumps at low temperature. Results of tests indicate feasible to use bearing in cryogenic environments and bearing damps bending-mode vibrations of flexible rotor as rotor accelerates or decelerates through speeds at which bending-mode oscillations excited.

Dirusso, Eliseo↗

NASA NTRS2019

Statistical Hypothesis Testing in Wavelet Analysis: Theoretical Developments and Applications to Indian Rainfall

Statistical hypothesis tests in wavelet analysis are methods that assess the degree to which a wavelet quantity(e.g., power and coherence) exceeds background noise. Commonly, a point-wise approach is adopted in which a wavelet quantity at every point in a wavelet spectrum is individually compared to the critical level of the point-wise test. However, because adjacent wavelet coefficients are correlated and wavelet spectra often contain many wavelet quantities, the point-wise test can produce many false positive results that occur in clusters or patches. To circumvent the point-wise test drawbacks, it is necessary to implement the recently developed area-wise, geometric, cumulative area-wise, and topological significance tests, which are reviewed and developed in this paper. To improve the computational efficiency of the cumulative area-wise test, a simplified version of the testing procedure is created based on the idea that its output is the mean of individual estimates of statistical significance calculated from the geometric test applied at a set of point-wise significance levels. Ideal examples are used to show that the geometric and cumulative area-wise tests are unable to differentiate wavelet spectral features arising from singularity-like structures from those associated with periodicities. A cumulative arc-wise test is therefore developed to strictly test for periodicities by using normalized arc length, which is defined as the number of points composing a cross section of a patch divided by the wavelet scale in question. A previously proposed topological significance test is formalized using persistent homology profiles (PHPs) measuring the number of patches and holes corresponding to the set of all point-wise significance values. Ideal examples show that the PHPs can be used to distinguish time series containing signal components from those that are purely noise. To demonstrate the practical uses of the existing and newly developed statistical methodologies, a first comprehensive wavelet analysis of Indian rainfall is also provided. An R software package has been written by the author to implement the various testing procedures.

Wind speed↗

DOE OSTI2020

Using an Advanced Distribution Management System Test Bed to Evaluate the Impact of Model Quality on Volt/VAR Optimization: Preprint

In this paper, we present a test bed for evaluating existing and future advanced distribution management system (ADMS) applications in a realistic laboratory setting, including other utility management systems and field equipment. We present an example of using it to evaluate the impact of the ADMS network model quality on a Volt/VAR optimization (VVO) application. The test bed integrates a commercial ADMS with a real-time simulation model of a utility distribution feeder. Representative power and controller hardware are integrated through hardware-in-the-loop (HIL) techniques. The performance of the ADMS VVO application is also evaluated for different levels of measurement density. Initial results indicate that a higher model quality achieves the highest possible energy savings while avoiding voltage violations, whereas a lower model quality results in increased energy savings but at the expense of more voltage violations.

ADMS↗

NASA NTRS1978

Hughes/GE improved NiCd cell design

Synchronous orbit and elliptical orbit life tests are used to make improvements in cell design for spacecraft application. The test increased the electrolyte volume and the surface area in cells to reduce the current density on charge and discharge.

Krause, S.↗

NASA NTRS2016

Performance Analysis of a Hardware Implemented Complex Signal Kurtosis Radio-Frequency Interference Detector

Radio-frequency interference (RFI) is a known problem for passive remote sensing as evidenced in the L-band radiometers SMOS, Aquarius and more recently, SMAP. Various algorithms have been developed and implemented on SMAP to improve science measurements. This was achieved by the use of a digital microwave radiometer. RFI mitigation becomes more challenging for microwave radiometers operating at higher frequencies in shared allocations. At higher frequencies larger bandwidths are also desirable for lower measurement noise further adding to processing challenges. This work focuses on finding improved RFI mitigation techniques that will be effective at additional frequencies and at higher bandwidths. To aid the development and testing of applicable detection and mitigation techniques, a wide-band RFI algorithm testing environment has been developed using the Reconfigurable Open Architecture Computing Hardware System (ROACH) built by the Collaboration for Astronomy Signal Processing and Electronics Research (CASPER) Group. The testing environment also consists of various test equipment used to reproduce typical signals that a radiometer may see including those with and without RFI. The testing environment permits quick evaluations of RFI mitigation algorithms as well as show that they are implementable in hardware. The algorithm implemented is a complex signal kurtosis detector which was modeled and simulated. The complex signal kurtosis detector showed improved performance over the real kurtosis detector under certain conditions. The real kurtosis is implemented on SMAP at 24 MHz bandwidth. The complex signal kurtosis algorithm was then implemented in hardware at 200 MHz bandwidth using the ROACH. In this work, performance of the complex signal kurtosis and the real signal kurtosis are compared. Performance evaluations and comparisons in both simulation as well as experimental hardware implementations were done with the use of receiver operating characteristic (ROC) curves. The complex kurtosis algorithm has the potential to reduce data rate due to onboard processing in addition to improving RFI detection performance.

microwaves↗

NASA NTRS2016

Performance Analysis of a Hardware Implemented Complex Signal Kurtosis Radio-Frequency Interference Detector

Radio-frequency interference (RFI) is a known problem for passive remote sensing as evidenced in the L-band radiometers SMOS, Aquarius and more recently, SMAP. Various algorithms have been developed and implemented on SMAP to improve science measurements. This was achieved by the use of a digital microwave radiometer. RFI mitigation becomes more challenging for microwave radiometers operating at higher frequencies in shared allocations. At higher frequencies larger bandwidths are also desirable for lower measurement noise further adding to processing challenges. This work focuses on finding improved RFI mitigation techniques that will be effective at additional frequencies and at higher bandwidths. To aid the development and testing of applicable detection and mitigation techniques, a wide-band RFI algorithm testing environment has been developed using the Reconfigurable Open Architecture Computing Hardware System (ROACH) built by the Collaboration for Astronomy Signal Processing and Electronics Research (CASPER) Group. The testing environment also consists of various test equipment used to reproduce typical signals that a radiometer may see including those with and without RFI. The testing environment permits quick evaluations of RFI mitigation algorithms as well as show that they are implementable in hardware. The algorithm implemented is a complex signal kurtosis detector which was modeled and simulated. The complex signal kurtosis detector showed improved performance over the real kurtosis detector under certain conditions. The real kurtosis is implemented on SMAP at 24 MHz bandwidth. The complex signal kurtosis algorithm was then implemented in hardware at 200 MHz bandwidth using the ROACH. In this work, performance of the complex signal kurtosis and the real signal kurtosis are compared. Performance evaluations and comparisons in both simulation as well as experimental hardware implementations were done with the use of receiver operating characteristic (ROC) curves.

radiometers↗

NASA NTRS1995

NASA Wiring for Space Applications Program: Fiscal year 1994 - 1995 testing activities

The results of the testing of wire insulation materials for space applications is presented in this report. The wire insulations tested were partially fluorinated polyimide, extruded ETFE, extruded PTFE, PTFE tape, and PTFE/Kapton. The tests performed were flammability tests, odor tests, compatibility tests with aerospace fluids, offgassing tests, and thermal vacuum stability tests.

Johnson, Harry T.↗