Results for “COMPACTING” — Page 27

NASA NTRS2011

Optical Design and Performance of the Ultra-Compact Imaging Spectrometer

We present the optical design and performance of the Ultra-Compact Imaging Spectrometer (UCIS) currently under development at Caltech's Jet Propulsion Laboratory. The new instrument demonstrates a low optical bench mass of less than 0.5 kg and compact size that enables Mars Rover or other in situ planetary applications. UCIS is a F/4, wide field (30deg) design, covering the spectral range 500-2600 nm and is enabled by a simple all aluminum two-mirror telescope and Offner spectrometer. We discuss here the optical design and alignment method that enables this compact and low mass imaging spectrometer and demonstrate successful spectrometer alignment with smile and keystone levels at 2-3% of a pixel width.

Imaging spectroscopy↗

NASA NTRS2015

Investigation of Unsteady Flow Interaction Between an Ultra-Compact Inlet and a Transonic Fan

In the present study, unsteady flow interaction between an ultra-compact inlet and a transonic fan stage is investigated. Future combat aircraft require ultra-compact inlet ducts as part of an integrated, advanced propulsion system to improve air vehicle capability and effectiveness to meet future mission needs. The main purpose of the study is to advance the current understanding of the flow interaction between two different ultra-compact inlets and a transonic fan for future design applications. Both URANS and LES approaches are used to calculate the unsteady flow field and are compared with the available measured data. The present study indicates that stall inception is mildly affected by the distortion pattern generated by the inlet with the current test set-up. The numerical study indicates that the inlet distortion pattern decays significantly before it reaches the fan face for the current configuration. Numerical results with a shorter distance between the inlet and fan show that counter-rotating vortices near the rotor tip due to the serpentine diffuser affects fan characteristics significantly.

Inlet↗

NASA NTRS2018

Compact Telescoping Surface Array for Mars Solar Power

This paper describes a lightweight, large-area solar array concept for Mars surface power called the Compact Telescoping Surface Array (CTSA). The design is derived from the Compact Telescoping Array (CTA) proposed in 2015 for high-power spacecraft. The CTSA deploys horizontally from Mars landers, provides 1000 sq.m of solar cell area, and generates about 50-80 kW daytime and 10 kW nighttime power (from energy storage) near the equator with clear skies. The total mass is about 1500 kg, and the stowed volume is about 10 cu.m, equivalent to 200 W/kg and 30 kW/cu.m at 1 astronomical unit (AU) from the sun. These challenging mass and volume goals require compact, lightweight structures to deploy and tension thin solar cell blankets in the Mars 0.38 g gravity field. Other features include single-axis rotation for daily or seasonal sun tracking, dust shedding, and feathering in high winds and sufficient strength for sustained 40 m/s winds in dust storms and brief 100 m/s winds in dust devils (dynamic pressure of 120 Pa). Based on preliminary design and analysis reported in the paper, CTSA appears to be a feasible approach for 1000 sq.m-class Mars solar arrays that autonomously deploy from landers prior to human arrival.

Pappa, Richard↗

NASA NTRS2018

Compact Mid-Wave Imaging System (CMIS) for Retrieval of Cloud Motion Vectors and Cloud Geometric Heights

The Johns Hopkins University Applied Physics Laboratory (JHU/APL) is developing a compact, light-weight, and low power midwave-infrared (MWIR) imager called the Compact Midwave Imaging Sensor (CMIS), under the support of the NASA Earth Science Technology Office Instrument Incubator Program. The goal of this CMIS instrument development and demonstration project is to increase the technical readiness of CMIS, a multi-spectral sensor capable of retrieving 3D winds and cloud heights 24/7, for a space mission. The CMIS instrument employs an advanced MWIR detector that requires less cooling than traditional technologies and thus permits a compact, low-power design, which enables accommodation on small spacecraft such as CubeSats. CMIS provides the critical midwave component of a multi-spectral sensor suite that includes a high-resolution Day-Night Band and a longwave infrared (LWIR) imager to provide global cloud characterization and theater weather imagery. In this presentation, an overview of the CMIS project, including the high-level sensor design, the concept of operations, and measurement capability will be presented. System performance for a variety of different scenes generated by a cloud resolving model (CRM) will also be discussed.

midwave↗

NASA NTRS2019

Innovative Compact Coronagraph Approach for Balloon-Borne Investigation of Temperature and Speed of Electrons in the Corona (BITSE)

We are developing an innovative compact coronagraph for studying the physical conditions in the solar wind acceleration region. This paper presents the new development of the compact coronagraph for the investigation of temperature and speed of electrons in the solar corona. The proposed compact coronagraph is a one stage externally occulted coronagraph without internal occulter or Lyot stop mask. The key of the new idea is to set the inner field cutoff at the External Occulter (EO) much smaller than the specified inner field cutoff. A second occulter on the surface of the detector array removes the remaining diffraction. The occulter on the detector surface functions similar to an internal occulter with the Inner Field of View Cutoff (IFoVC) exactly the same as specified. For BITSE, the desired inner field cutoff is 3 R, but the cutoff at EO is only 1.5 R☉. The diffraction analysis shows that in the sensor plane, the diffraction intensity at the 3 R☉ is not sensitive to the EO cutoff, either at 1.5 R☉ or close to 3 R☉. The advantage of having a smaller EO cutoff is that the vignetting decreased for the Field of View (FoV) near 3 R☉, therefore, the signal increases. Meanwhile, the diffraction of Point Spread Function is much less in the radial direction, which not only increases the image quality around 3 R☉, but also increases the encircled energy and signal to noise ratio. In other words, the data is useful right at 3 R☉! The BITSE optical design and diffraction analysis will be presented in detail. The simulation shows the signal to noise ratio obtained from the diffraction and vignetting data enables corona temperature and speed measurement.

Gong, Qian↗

NASA NTRS2019

Innovative Compact Coronagraph Approach for Balloon-Borne Investigation of Temperature and Speed of Electrons in the Corona (BITSE)

We are developing an innovative compact coronagraph for studying the physical conditions in the solar wind acceleration region. This paper presents the new development of the compact coronagraph for the investigation of temperature and speed of electrons in the solar corona. The proposed compact coronagraph is a one stage externally occulted coronagraph without internal occulter or Lyot stop mask. The key of the new idea is to set the inner field cutoff at the External Occulter (EO) much smaller than the specified inner field cutoff. A second occulter on the surface of the detector array removes the remaining diffraction. The occulter on the detector surface functions similar to an internal occulter with the Inner Field of View Cutoff (IFoVC) exactly the same as specified. For BITSE, the desired inner field cutoff is 3 R, but the cutoff at EO is only 1.5 R☉. The diffraction analysis shows that in the sensor plane, the diffraction intensity at the 3 R☉ is not sensitive to the EO cutoff, either at 1.5 R☉ or close to 3 R☉. The advantage of having a smaller EO cutoff is that the vignetting decreased for the Field of View (FoV) near 3 R☉, therefore, the signal increases. Meanwhile, the diffraction of Point Spread Function is much less in the radial direction, which not only increases the image quality around 3 R☉, but also increases the encircled energy and signal to noise ratio. In other words, the data is useful right at 3 R☉! The BITSE optical design and diffraction analysis will be presented in detail. The simulation shows the signal to noise ratio obtained from the diffraction and vignetting data enables corona temperature and speed measurement.

Gong, Qian↗

NASA NTRSDate not supplied

A Generalized, Compactly-Supported Correlation Function for Data Assimilation Applications

Correlation functions play an essential role in modern data assimilation, where they are used to model covariances given a set of tunable parameters or applied as tapering functions to localize covariances in ensemble-based schemes. One of the most widely-used correlation functions in data assimilation is the Gaspari and Cohn (1999) piecewise-rational, compactly-supported parametric correlation function (hereafter referred to as GC99). The GC99 correlation function is useful due to its tunable cut-off parameter c and Gaussian-like shape achieved when the parameter a is set to one-half. These properties are attractive for tapering functions in data assimilation applications. However, the GC99 correlation function is homogeneous over Euclidean 3-space and isotropic when restricted to the sphere, properties that may be less than ideal for some geophysical applications. GC99 is also compactly-supported on a sphere of fixed radius, which requires tuning of the cut-off parameter c that can depend on the specific application. This work presents a generalization of the GC99 correlation function that allows the cut-off parameter c and shape parameter a to vary over space to gain more flexibility in shape while maintaining its compact support property. The function, which we call the Generalized Gaspari Cohn (GenGC) correlation function, introduces inhomogeneity in Euclidean 3-space and anisotropy when restricted to the sphere by allowing both parameters c and a to vary, as functions, over the spatial domain. The GC99 correlation function is a special case of GenGC where the functions c and a are held constant, as fixed parameters rather than functions. The GenGC correlation function also generalizes the follow-on to the work of Gaspari and Cohn (1999) presented in Gaspari et al. (2006), which allowed a to vary while keeping c fixed. We illustrate through simple one- and two-dimensional examples the variety of inhomogeneous and anisotropic correlation functions GenGC can produce by varying c and a over space, and suggest applications where they may be useful in data assimilation, such as covariance modeling or localization. In particular, we describe how the GenGC correlation function can be used to construct covariances using correlation length and variance fields derived from dynamics. For example, the correlation length field for advective dynamics is governed by a partial differential equation (PDE) in N spatial dimensions, where N is the number of space dimensions of the state. Correlation length fields can be determined from this PDE and used with GenGC to construct the corresponding correlations. We can then approximate the full covariance by rescaling by the variance, which also satisfies a PDE in N spatial dimensions for advective dynamics. Thus we can approximate the full covariance without solving the covariance PDE, which is in 2N spatial dimensions, by solving just two PDEs each in only N spatial dimensions. This approach to evolving the correlation length and variance fields, then reconstructing the correlations using GenGC, is suggested as an alternative to current methods of covariance modeling in data assimilation algorithms.

GC99↗

DOE OSTI2012

Microscopic analysis of irradiated AGR-1 coated particle fuel compacts

The AGR-1 experiment involved irradiation of 72 TRISO-coated particle fuel compacts to a peak burnup of 19.5% FIMA with no in-pile failures observed out of 3×105 total particles. Irradiated AGR-1 fuel compacts have been cross-sectioned and analyzed with optical microscopy to characterize kernel, buffer, and coating behavior. Five compacts have been examined so far, spanning a range of irradiation conditions (burnup, fast fluence, and irradiation temperature) and including all four TRISO coating variations irradiated in the AGR-1 experiment. The cylindrical specimens were sectioned both transversely and longitudinally, then polished to expose between approximately 40-80 individual particles on each mount. The analysis focused primarily on kernel swelling and porosity, buffer densification and fracturing, buffer-IPyC debonding, and fractures in the IPyC and SiC layers. Characteristic morphologies have been identified, over 800 particles have been classified, and spatial distributions of particle types have been mapped. No significant spatial patterns were discovered in these cross sections. However, some trends were found between morphological types and certain behavioral aspects. Buffer fractures were found in approximately 23% of the particles, and these fractures often resulted in unconstrained kernel swelling into the open cavities. Fractured buffers and buffers that stayed bonded to IPyC layers appear related to larger pore size in kernels. Buffer-IPyC interface integrity evidently factored into initiation of rare IPyC fractures. Fractures through part of the SiC layer were found in only three particles, all in conjunction with IPyC-SiC debonding. Compiled results suggest that the deliberate coating fabrication variations influenced the frequencies of IPyC fractures, IPyC-SiC debonds, and SiC fractures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2013

Compaction and Sintering of Mo Powders

To support the development of Mo-99 production by NorthStar Medical Technologies, LLC, Mo metal powders were evaluated for compaction and sintering characteristics as they relate to Mo-100 accelerator target disk fabrication. Powders having a natural isotope distribution and enriched Mo-100 powder were examined. Various powder characteristics are shown to have an effect on both the compaction and sintering behavior. Natural Mo powders could be cold pressed directly to >90% density. All of the powders, including the Mo-100 samples, could be sintered after cold pressing to >90% density. As an example, a compacted Mo-100 disk reached 89.7% density (9.52 g/cm3) after sintering at 1000 C for 1 hr. in flowing Ar/4%H2. Higher sintering temperatures were required for other powder samples. The relationships between processing conditions and the resulting densities of consolidated Mo disks will be presented.

Nunn, Stephen D↗

DOE OSTI2020

High Effectiveness, Compact, High Pressure and Low-Cost Recuperator, Presented at The Fifth International Symposium – Super-Critical CO2 Power Cycles, San Antonio, Texas, March 28-31, 2016, by Dr. John Kelly, President, Altex Technologies Corporation

Closed Brayton super-critical CO2 power cycles are well suited to waste heat bottoming cycles, due to their increased efficiency and compactness, relative to Rankine steam bottoming cycles. Since waste heat applications would be retrofits, the power system compactness is important. To achieve high efficiency, these power cycles require high pressure recuperative type heat exchangers, of substantial heat duty. Current Printed Circuit Heat Exchangers (PCHE), originally developed for high pressure gas and oil applications, can be used as recuperators, but costs are higher than desired. Altex is developing a purpose-built high pressure and effectiveness recuperator to provide the reliability, compactness, performance and pressure capability of current recuperators, but at a reduced cost. The High Effectiveness Low Cost (HELC) recuperative heat exchanger design yields volume and weight metrics of .0024 m3/UA and 10.2 kg/UA, which are 4% and 77.3% below recuperator target metrics, respectively. A 50 kW test article was designed and fabricated. Performance tests on water and oil showed that the HELC design model could predict heat transfer, to within 10% of the measured value. This model was then used to project HELC performance, when operating on supercritical CO2. Besides performance tests, the test article was hydrostatically tested, for integrity at up to 4,000 psi pressure. At these conditions, some distortion of channels was encountered. To mitigate distortion, the inserts were redesigned and these results were used to project the cost of 500 kW and 5,083 kW HELC units. The cost metric for the 5,083 kW unit was determined to be $1,349/UA, which is 10% lower than the recuperator desired cost metric desired target of $1,500/UA. In addition, the 5,083 kW unit HELC cost of $61.09/kW is 33.6% lower than the $92/kW estimated cost for a PCHE. Hydrostatic pressure tests, at up to 4,000psi, showed that the unit did not leak. However, channels were distorted at this pressure differential. Design updates to minimize stress concentrations and distortion were prepared and analyzed, to show that distortion could be controlled, but to date tests have not been run to prove the design. Project results show the potential of the HELC approach, but more work is required to confirm this potential, at the larger scales of interest.

14 SOLAR ENERGY↗

DOE OSTI2020

High Effectiveness, Compact, High Pressure and Low Cost Recuperator for Super-Critical CO2 Power Cycles, Paper Presented at The Fifth International Symposium – Super-Critical CO2 Power Cycles, San Antonio, Texas, March 28-31, 2016, by Dr. John Kelly, President, Altex Technologies Corporation

Closed Brayton super-critical CO2 power cycles are well suited to waste heat bottoming cycles, due to their increased efficiency and compactness, relative to Rankine steam bottoming cycles. Since waste heat applications would be retrofits, the power system compactness is important. To achieve high efficiency, these power cycles require high pressure recuperative type heat exchangers, of substantial heat duty. Current Printed Circuit Heat Exchangers (PCHE), originally developed for high pressure gas and oil applications, can be used as recuperators, but costs are higher than desired. Altex is developing a purpose-built high pressure and effectiveness recuperator to provide the reliability, compactness, performance and pressure capability of current recuperators, but at a reduced cost. The High Effectiveness Low Cost (HELC) recuperative heat exchanger design yields volume and weight metrics of .0024 m3/UA and 10.2 kg/UA, which are 4% and 77.3% below recuperator target metrics, respectively. A 50 kW test article was designed and fabricated. Performance tests on water and oil showed that the HELC design model could predict heat transfer, to within 10% of the measured value. This model was then used to project HELC performance, when operating on supercritical CO2. Besides performance tests, the test article was hydrostatically tested, for integrity at up to 4,000 psi pressure. At these conditions, some distortion of channels was encountered. To mitigate distortion, the inserts were redesigned and these results were used to project the cost of 500 kW and 5,083 kW HELC units. The cost metric for the 5,083 kW unit was determined to be $1,349/UA, which is 10% lower than the recuperator desired cost metric desired target of $1,500/UA. In addition, the 5,083 kW unit HELC cost of $61.09/kW is 33.6% lower than the $92/kW estimated cost for a PCHE. Hydrostatic pressure tests, at up to 4,000psi, showed that the unit did not leak. However, channels were distorted at this pressure differential. Design updates to minimize stress concentrations and distortion were prepared and analyzed, to show that distortion could be controlled, but to date tests have not been run to prove the design. Project results show the potential of the HELC approach, but more work is required to confirm this potential, at the larger scales of interest.

14 SOLAR ENERGY↗

DOE OSTI2020

Techno-Economic Analysis for GTI's Compact Hydrogen Generator

A technoeconomic analysis of the compact hydrogen generator compared to a traditional steam methane reformer (SMR) was performed for both processes with and without carbon capture. The project goal for the technoeconomic analysis was to demonstrate a minimum of 20% lower CAPEX and 15% lower levelized cost of hydrogen compared to SMR with and without carbon capture. GTI obtained baseline capital and costs for the SMR with and without and methodology to calculate the levelized cost of hydrogen from an IEAGHG Technical Report: 2017-02 Techno-Economic Evaluation of SMR Based Standalone (Merchant) Hydrogen Plant with CCS. This methodology was then applied to GTI’s compact hydrogen generator using direct material costs previously obtained from a reputable engineering procurement and construction company, CB&I Howe-Baker. The analysis was performed for plants producing 90MMSCFD (million standard cubic feed per day) of hydrogen. Direct material costs were converted to total installed costs and total capital requirements using the same multiplying factors for both processes. We have found that the direct materials cost of the compact hydrogen generator is less than half the direct materials cost required for SMR without capture, and about one quarter the direct materials cost of SMR with carbon capture. This low materials cost translates into a significant CAPEX savings and lower levelized cost of hydrogen that exceed the goals of the techno-economic assessment. We have found that the CHG has a 43% lower installed cost and capital requirement compared to SMR without capture, that results in a levelized cost of hydrogen that is 19% lower than SMR. When 90% CO2 capture is added to the plants, the advantages is even better. The CHG has a 51% lower installed and capital requirement compared to SMR with capture, resulting in a 28% lower levelized cost of hydrogen. A sensitivity analysis was performed and showed natural gas feedstock cost and discount rate to be the main contributors to hydrogen price sensitivity. Given these significant cost advantages, GTI is encouraged to continue to develop the technology and market the economic advantages as well as the efficiency gains and ability to inherently capture CO2.

08 HYDROGEN↗

DOE OSTI2012

Principles of Product Quality Control of German Radioactive Waste Forms from the Reprocessing of Spent Fuel: Vitrification, Compaction and Numerical Simulation - 12529

The German product quality control is inter alia responsible for control of two radioactive waste forms of heat generating waste: a) homogeneous vitrified HLW and b) heterogeneous compacted hulls, end-pieces and technological metallic waste. In either case, significantly different metrology is employed at the site of the conditioning plant for the obligatory nuclide inventory declaration. To facilitate an independent evaluation and checking of the accompanying documentation numerical simulations are carried out. The physical and chemical properties of radioactive waste residues are used to assess the data consistency and uncertainty margins, as well as to predict the long-term behavior of the radioactive waste. This is relevant for repository acceptance and safety considerations. Our new numerical approach follows a bottom-up simulation starting from the burn-up behavior of the fuel elements in the reactor core. The output of these burn-up calculations is then coupled with a program that simulates the material separation in the subsequent dissolution and extraction processes normalized to the mass balance. Follow-up simulations of the separated reprocessing lines of a) the vitrification of highly-active liquid and b) the compaction of residual intermediate-active metallic hulls remaining after fuel pellets dissolution, end-pieces and technological waste, allows calculating expectation values for the various repository relevant properties of either waste stream. The principles of the German product quality control of radioactive waste residues from the spent fuel reprocessing have been introduced and explained. Namely, heat generating homogeneous vitrified HLW and heterogeneous compacted metallic MLW have been discussed. The advantages of a complementary numerical property simulation have been made clear and examples of benefits are presented. We have compiled a new program suite to calculate the physical and radio-chemical properties of common nuclear waste residues. The immediate benefit is the independent assessment of radio-active inventory declarations and much facilitated product quality control of waste residues that need to be returned to Germany and submitted to a German HLW-repository requirements. Wherever possible, internationally accepted standard programs are used and embedded. The innovative coupling of burn-up calculations (SCALE) with neutron and gamma transport codes (MCPN-X) allows an application in the world of virtual waste properties. If-then-else scenarios of hypothetical waste material compositions and distributions provide valuable information of long term nuclide property propagation under repository conditions over a very long time span. Benchmarking the program with real residue data demonstrates the power and remarkable accuracy of this numerical approach, boosting the reliability of the confidence aforementioned numerous applications, namely the proof tool set for on-the-spot production quality checking and data evaluation and independent verification. Moreover, using the numerical bottom-up approach helps to avoid the accumulation of fake activities that may gradually build up in a repository from the so-called conservative or penalizing nuclide inventory declarations. The radioactive waste properties and the hydrolytic and chemical stability can be predicted. The interaction with invasive chemicals can be assessed and propagation scenarios can be developed from reliable and sound data and HLW properties. Hence, the appropriate design of a future HLW repository can be based upon predictable and quality assured waste characteristics. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

DEM and MELT: A Modular and Compact In-Can Melting Technology Dedicated to D and D and Remediation Waste - 20033

The DEM and MELT In-Can vitrification process is designed to process intermediate and high level waste coming for D and D and remediation operations. It is developed to treat liquid and solid waste, to produce a small amount of secondary waste and to minimize investment and operating costs. This In-Can vitrification process is also developed with a compact and modular design and can be adapted regarding nuclear operators' needs and requirements. Furthermore, this robust and simple process is flexible enough to accommodate most uncertainties on waste composition. The DEM and MELT process is developed through the French consortium coordinated by CEA which gathers Orano, ECM technologies and Andra. In the frame of this project, Orano has designed a compact and modular layout of the process allowing an efficient in situ implementation, close to the waste to be treated. This paper presents the compact and modular design of the DEM and MELT process and the way it can be used for a short duration, as a decommissioning tool aimed to be dismantled just after the treatment operation. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2025

Dynamical Heating from Dark Compact Objects and Axion Minihalos: Implications for the 21-cm Signal

The temperature of baryons at the end of the cosmic dark ages can be inferred from observations of the 21-cm hyperfine transition in neutral hydrogen. Any energy injection from the dark sector can therefore be detected through these measurements. Dark compact objects and dark-matter substructures can modify the baryon temperature by transferring heat via dynamical friction. In this work, we evaluate the prospects for detecting dynamical friction-induced heating from dark compact objects with a mass in the range $10^2 M_{\odot}$ to $10^5 M_{\odot}$, as well as from axion minihalos, using upcoming 21-cm experiments. We find that both the 21-cm global signal and power-spectrum measurements will be sensitive to dark compact objects that constitute about 10% of the dark matter, and will substantially improve our sensitivity to axion-like particles with masses in the range $10^{-18}$ eV to $10^{-9}$ eV.

Bhalla, Badal [Oklahoma U.] (ORCID:000000030488664↗

DOE OSTI2026

A Chemodynamical Census of the Milky Way's Ultra-Faint Compact Satellites. I. A First Population-Level Look at the Internal Kinematics and Metallicities of 19 Extremely-Low-Mass Halo Stellar Systems

Deep, wide-area photometric surveys have uncovered a population of compact ($r_{1/2} \approx$ 1-15 pc), extremely-low-mass ($M_* \approx$ 20-4000 $M_{\odot}$) stellar systems in the Milky Way halo that are smaller in size than known ultra-faint dwarf galaxies (UFDs) and substantially fainter than most classical globular clusters (GCs). Very little is known about the nature and origins of this population of "Ultra-Faint Compact Satellites" (UFCSs) owing to a dearth of spectroscopic measurements. Here, we present the first spectroscopic census of these compact systems based on Magellan/IMACS and Keck/DEIMOS observations of 19 individual UFCSs, representing $\sim$2/3 of the known population. We securely measure mean radial velocities for all 19 systems, velocity dispersions for 15 (predominantly upper limits), metallicities for 17, metallicity dispersions for 8, and $\textit{Gaia}$-based mean proper motions for 18. This large new spectroscopic sample provides the first insights into population-level trends for these extreme satellites. We demonstrate that: (1) the UFCSs are kinematically colder, on average, than the UFDs, disfavoring very dense dark matter halos in most cases, (2) the UFCS population is chemically diverse, spanning a factor of $\sim$300 in mean iron abundance ($\rm -3.3 \lesssim [Fe/H] \lesssim -0.8$), with multiple systems falling beneath the "metallicity floor" proposed for GCs, and (3) while some higher-metallicity and/or younger UFCSs are clearly star clusters, the dynamical and/or chemical evidence allows the possibility that up to $\sim$50% of the UFCSs in our sample (9 of 19) may represent the smallest and least-massive galaxies yet discovered.

Cerny, William [Yale U.] (ORCID:0000000316977062)↗

DOE OSTI2026

Discovery and Spectroscopic Characterization of a Distant, Compact Milky Way Satellite in Gemini

We present the discovery of a compact Milky Way satellite in the constellation of Gemini. This system was discovered by cross-matching detections from two independent search algorithms applied to Blanco/DECam data from the third data release of the DECam Local Volume Exploration survey (DELVE DR3), and confirmed with deeper imaging from Gemini/GMOS-N. Based on these data, we determine that the system is an ultra-faint ($M_V = -2.1^{+0.4}_{-0.6}$), compact ($r_{1/2} = 8.6^{+1.4}_{-1.2}$ pc) system located at a heliocentric distance of $120^{+7}_{-6}$ kpc. These physical properties place the system in the regime of ambiguous, ultra-faint compact Milky Way halo satellites that cannot be confidently classified as dwarf galaxies or star clusters from morphology alone; we therefore name the system DELVE 8/Gemini I. From medium-resolution Keck/DEIMOS spectroscopy, we securely identify four members including two blue horizontal branch stars, confirming the system as a bound satellite moving at a mean radial velocity of $v_{\rm hel} = -82.7^{+3.7}_{-3.9} {\rm km\,s}^{-1}$. We also use these spectra to place an upper limit of $\rm [Fe/H] \lesssim -2.5$ on the metallicity of DELVE 8/Gemini I's brightest star, supporting the classification of the system as either an ancient star cluster or ultra-faint dwarf galaxy. The discovery of faint, distant systems similar to DELVE 8/Gemini I is expected to become more common with upcoming surveys.

Overdeck, K. [Chicago U., Astron. Astrophys. Ctr.;↗

DOE OSTI2025

Fuel performance analysis of fully-resolved TRISO compact

The TRi-structural ISOtropic (TRISO) fuel multilayered coating structure offers multiple barriers to fission product release, enhancing safety and performance. The heterogeneous nature of TRISO fuel compacts, comprising thousands of randomly distributed coated fuel particles embedded in a graphite matrix, creates intricate stress fields and thermal gradients that cannot be accurately modeled using simplified one-dimensional or homogenized approaches. Consequently, three-dimensional modeling enables the prediction of fuel compact dimensional changes, internal pressure buildup, and fission product transport pathways under diverse irradiation and thermal conditions. This capability facilitates detailed analysis of particle-to-particle interactions, matrix cracking mechanisms, and the statistical distribution of coating failures, which directly impact fuel performance and safety margins. This capability is particularly critical for advanced reactors, such as high-temperature gas-cooled reactors and other Generation IV reactor designs where TRISO fuel operates at elevated temperatures and burn-up levels. This work introduces a novel method to generate an optimized packing of TRISO compacts and a complete 3D mesh with random distribution of TRISO particles, which are discretized into each coating component layer.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗