Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONCENTRATION RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Understanding the setting and hardening process of wollastonite-based brushite cement. Part 2: Influence of the boron and aluminum concentrations in the mixing solution

The mixing solution of wollastonite-based brushite cement is a phosphoric acid solution containing metallic cations and borax. This work complements a previous study devoted to the influence of the H{sub 3}PO{sub 4} concentration, Ca/P and liquid-to-solid (l/s) ratios on the setting and hardening process of the binder by providing new insight into the role of aluminum and boron. Boron retards the setting and decreases the heat released during the process. It also contributes to reduce the macroporosity of the hardened material but yields to poor compressive strength. With aluminum in the mixing solution, the mechanical properties are greatly improved thanks to the precipitation of an amorphous aluminophosphate which increases the density of the cement matrix. But aluminum alone leads to fast setting. A joint addition of boron and aluminum to the mixing solution makes it possible to get a material with optimized properties both in fresh and hardened states.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Critical pitting temperature of selective laser melted 316L stainless steel: A mechanistic approach

In this work, the critical pitting temperature (CPT) of selective laser melted (SLM) 316 L stainless steel in 1.0 M NaCl was measured and compared with a commercial wrought alloy. Potentiostatic measurements determined a mean CPT value of 16 ± 0.7 °C, 27.5 ± 0.8 °C and 31 ± 1 °C for the wrought alloy, the SLM alloy normal to the build direction and parallel to the build direction, respectively. The lead-in pencil electrode technique was used to study the pit chemistry of the two alloys and to explain the higher CPT values observed for the SLM alloy. A lower critical current density required for passivation in a simulated pit solution was measured for the SLM alloy. Moreover, the ratio of the critical concentration to saturated concentration of dissolving metal cations was found to be higher for the SLM alloy, which was related to its different salt film properties, possibly as a result of the SLM’s distinct microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A critical analysis of U-Pu-Zr phase transitions using calorimetric, microstructural, and phase equilibria data

Metallic fuels consisting primarily of uranium, plutonium, and zirconium (U-Pu-Zr) are a leading material candidate for fast-spectrum nuclear reactors. Early demonstration programs proved the principle of safe and efficient fast reactor operation, however there is still considerable uncertainty regarding the phase equilibria and microstructural evolution across the ternary composition space. Quantitative phase formation and identification measurements are scarce and often incomplete, with studies reporting either phase transition temperatures or phase identification data, but not both from the same specimens. In this study, we critically compared experimental and calculated phase transition data and correlated with the microstructure and phase characterization data of as-cast and annealed U-Pu-Zr alloys. Differential scanning calorimetry (DSC) was used to measure phase transitions in the subsolidus regions (723−948 K) of three ternary U-Pu-Zr alloys with similar plutonium concentrations but various U/Zr ratios. Due to sluggish kinetics and narrow ranges of phase stability, complex peaks required the use of a Frazier-Suzuki peak fitting algorithm to deconvolute and calculate transition peak temperatures and enthalpies. We also identified trends of phase transition behavior by critically comparing our DSC data with previous phase transition measurements as well as historical and calculated phase equilibrium diagrams. In conclusion, this provides a critical approach for benchmarking and assessing the quality of new U-Pu-Zr phase equilibria data prior to its incorporation into nuclear material databases.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Creation of a High-Yield AAV Vector Production Platform in Suspension Cells Using a Design-of-Experiment Approach

Recombinant adeno-associated virus (rAAV) vectors are a leading gene delivery platform, but vector manufacturing remains a challenge. New methods are needed to increase rAAV yields and reduce costs. Past efforts to improve rAAV production have focused on optimizing a single variable at a time, but this approach does not account for the interactions of multiple factors that contribute to vector generation. Here, we utilized a design-of-experiment (DOE) methodology to optimize rAAV production in a HEK293T suspension cell system. We simultaneously varied the transgene, packaging, and helper plasmid ratios, the total DNA concentration, and the cell density to systematically evaluate the impact of each variable across 52 conditions. The results revealed a unique set of parameters with a lower concentration of transgene plasmid, a higher concentration of packaging plasmid, and a higher cell density than previously described protocols. Using this DOE-optimized protocol, we achieved unpurified yields approaching 3 × 10 14 viral genomes (VGs)/L of cell culture. Additionally, we incorporated polyethylene glycol (PEG)-based virus precipitation, pH-mediated protein removal, and affinity chromatography to our downstream processing, enabling average purified yields of >1 × 10 14 VGs/L for rAAV-EGFPs across 13 serotypes and capsid variants.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Ultrahigh pressure compaction-resistant thin film crosslinked composite reverse osmosis membranes

In this study, we present a class of thin-film crosslinked (TFX) composite reverse osmosis (RO) membranes that resist physical compaction at ultrahigh pressures (up to 200 bar). Since RO membranes experience compaction at virtually all pressure ranges, the ability to resist compaction has widespread implications for RO membrane technology. The process described herein involves crosslinking a phase inverted porous polyimide (PI) support membrane followed by interfacial polymerization of a polyamide layer, thereby forming a fully thermoset composite membrane structure. We explore a range of phase inversion membrane formation parameters such as PI concentration, solvent-cosolvent ratios, coagulation bath composition, and crosslinking methods in addition to interfacial polymerization reaction chemistry and conditions. Overall, TFX membranes exhibit significantly less compaction compared to hand-cast and commercial high-pressure RO membranes, experiencing less than 10% decline in water permeance and maintaining salt rejection over 99% for NaCl solutions up to 180,000 mg/L with 200 bar applied pressure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Simple thermal vapor deposition process for and characterization of n-type indium oxysulfide thin films

The search continues for alternative nontoxic n-type electron transport layers in optoelectronic thin-film devices. Indium oxysulfide, In 2 (O,S) 3 , represents one promising material for this application, especially when paired with chalcogenide absorber layers. The ternary nature of the composition allows for electrical conductivity and optical bandgap tuning by tailoring the sulfur to oxygen ratio in the oxysulfide alloy. However, thin films of In 2 (O,S) 3 are typically deposited only by chemical bath deposition or plasma-enhanced atomic layer deposition. Here we report deposition of thin films of In 2 (O,S) 3 in a custom-built thermal reactor using only water vapor and hydrogen sulfide as the coreactants. This advance is enabled by the use of a recently reported, highly reactive indium formamidinate precursor. As shown by x-ray photoelectron spectroscopy, the composition can be tuned from pure In 2 (O,S) 3 to pure In 2 S 3 by varying the ratio of cycles employing water or hydrogen sulfide. The oxygen to the sulfur ratio in the film can be controlled by altering the dose sequence, although films typically contain more sulfur than would be expected naively from the percentage of hydrogen sulfide doses in the deposition recipe. Rutherford backscattering spectrometry confirms the composition is sulfur-rich relative to the dosing ratio. Structural characterization indicates films are relatively amorphous in nature. Electrically, these films offer reasonably constant electron mobility at different O:S ratios, with an electron concentration tunable over 4 orders of magnitude. These oxysulfide films possess a higher indirect bandgap than their oxygen-free indium sulfide counterparts, indicating higher transmittance to blue light. These indium oxysulfide films may be suitable candidates for electron transport layers in thin-film solar cells where their wider bandgap might result in higher optical transparency and thus short circuit current density, while the tunability of their conduction band offset with an absorber layer may result in higher open circuit voltage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Data and scripts associated with “When do Riverine Systems 'Feel the Burn'? Simulating How Burn Extent and Severity Modulate Hydrologic Controls on Biogeochemical Export” (v2)

This data package is associated with the publication “When do Riverine Systems 'Feel the Burn'? Simulating How Burn Extent and Severity Modulate Hydrologic Controls on Biogeochemical Export” published in Water Resources Research (Wampler et al. 2025; preprint: https://doi.org/10.22541/essoar.174438106.63564767/v1). This study used the Soil and Water Assessment Tool (SWAT), a processed based model to explore the impacts of area burned and burn severity on streamflow, nitrate, and dissolved organic carbon (DOC) in two test basins: a semi-arid, mixed land use basin and a humid, primarily forested basin. We developed 1800 wildfire scenarios that we ran in each basin: 20 different burn extents (5 to 100% by 5%), 3 different burn severities (low, moderate, and high), and 30 different post-fire precipitation scenarios. We also ran an additional 30 scenarios associated with no wildfire for the 30 post-fire precipitation scenarios. For each scenario we were interested in the change in runoff ratio (streamflow) and average concentration and annual loads (nitrate and DOC) across the wildfire scenarios. This data package contains the data and scripts required to build SWAT models for the two test basins, create and run the wildfire scenarios, and generate the data summaries and figures used in the associated manuscript. This data package was originally published in March 2025. It was updated in January 2026 (v2; new and modified files) to include the final files after the manuscript went through reviews. See the change history section below for more details. For details on how to navigate data packages generated by this project, see https://data.ess-dive.lbl.gov/portals/PNNLRiverCorridorSFA/About.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

First Ever Polymer Flood Field Pilot to Enhance the Recovery of Heavy Oils on Alaska North Slope – Producer Responses and Operational Lessons Learned

The US Department of Energy and Hilcorp Alaska, LLC are jointly cosponsoring a field pilot project entitled “First Ever Field Pilot on Alaska’s North Slope to Validate the Use of Polymer Floods for Heavy Oil Enhanced Oil Recovery (EOR).” The objective of this pilot is to perform a field experiment to validate the use of an advanced polymer flooding technology to unlock the vast heavy oil resources on Alaska North Slope (ANS). Two pairs of horizontal injection and production wells have been deployed in an isolated fault block of the Schrader Bluff heavy oil reservoir at the Milne Point Field to conduct a polymer flood pilot which was designed to acquire field performance data to optimize polymer flood design in the Schrader Bluff heavy oil reservoirs on ANS. Hydrolyzed polyacrylamide (HPAM) polymer injection started on August 28, 2018 using a custom made polymer mixing and pumping unit. Polymer solution properties such as concentration, viscosity, and filter ratio, have been closely monitored and adjusted as necessary. Operational procedures have been improved to ensure adequate injectivity and polymer propagation through the formation. Oil and water production is tested frequently to monitor water cut performance, and produced water is sampled and analyzed for polymer content. Tracers were pumped pre and post polymer injection startup to compare polymer flood breakthrough timing and sweep efficiency. Polymer injectivity of the horizontal wells drilled in the Schrader Bluff NB sand is found to be sufficient to replace the reservoir production voidage although there were some declines as high viscosity polymer swept the near wellbore region. Production data show significant reduction in water cut and the oil production rate has stabilized. No polymer production has been confirmed from the two horizontal producers after 22 months of polymer injection into the two supporting horizontal injectors. Tracer data show very low sweep efficiencies with waterflood alone, whereas significant improvement has been achieved with polymer flood. Many operational lessons have been learned and improvements have been made regarding polymer mixing, pumping, and onsite quality control, particularly in a challenging Arctic environment. Adequate polymer injection rate can be achieved with diligent monitoring and quality assurance of the properties of the injected polymer solution.

Ning, Samson↗
DOE OSTI2025

Combined TDLAS and chemiluminescence imaging in a flat flame burner operated with NH3/H2 blends

Ammonia is viewed as a viable hydrogen carrier due to favorable storage and transport characteristics. While it can be re-converted to hydrogen at point-of-use via thermal catalytic cracking, direct utilization in combustion systems can result in reduced costs and improved efficiency. A major barrier to this approach is the low flammability and potential for high nitrogen oxide emissions, driven by fuel-bound nitrogen and complex kinetic pathways. While a number of kinetic mechanisms currently exist for simulating ammonia combustion, a major need continues to be direct information about species profiles in easy-to-model systems capable of isolating chemical kinetics from multi-dimensional fluid dynamic effects. This paper reports on recent species measurements made in a flat flame burner using a combined tunable-diode-laser-absorption-spectroscopy (TDLAS) and chemiluminescence imaging approach. Three flame conditions were included representative of NH3/H2 blends, partially cracked NH3 (inc. N2), and 100% NH3 with enhanced air (30% oxygen). Two NIR distributed feedback (DFB) laser diodes were used to determine H2O concentration and temperature (via ratio thermometry) at various radial and axial positions, after which an inverse Abel transform was used to infer centerline values. Companion images were collected using a Princeton Instrument PI-MAX intensified camera equipped with a 105mm UV lens and multiple filter sets targeting OH*, NH*, and NH2* emission. Results were compared to companion Cantera burner-stabilized flame simulations using various kinetic mechanisms. A recent mechanism including excited species chemistry was also included, to investigate whether excited and ground state profiles exhibit significant differences.

ammonia combustion↗
NASA NTRS1973

Parametric test results of a swirl-can combustor

Pollutant levels of oxides of nitrogen, unburned hydrocarbons, and carbon monoxide were measured for three models of an experimental, annular swirl can combustor. The combustor was 1.067 meters in outer diameter, incorporated 120 modules, and was specifically designed for elevated exit temperature performance. Test conditions included combustor inlet temperatures of 589, 756 and 839 K, inlet pressures of 3 to 6.4 atmospheres, reference velocities of 21 to 38 meters per second and combustor equivalence ratios, based on total combustor flows of 0.206 to 1.028. Maximum oxides of nitrogen emission index values occurred at an equivalence ratio of 0.7 with lower values measured for both higher and lower equivalence ratios. Oxides of nitrogen concentrations, to the 0.7 level with 756 K inlet air, were correlated for the three models by a combined parameter consisting of measured flow and geometric parameters. Effects of the individual parameters comprising the correlation are also presented.

Niedzwiecki, R. W.↗
NASA NTRS1980

Radiation damage annealing mechanisms and possible low temperature annealing in silicon solar cells

The defect responsible for reverse annealing in 2 ohm/cm n(+)/p silicon solar cells was identified. This defect, with energy level at e sub v + 0.30 eV was tentatively identified as a boron oxygen-vacancy complex. Results indicate that its removal could result in significant annealing for 2 ohm/cm and lower resistivity cells at temperatures as low as 200 C. These results were obtained by use of an expression derived from the Shockley-Read-Hall recombination theory which relates measured diffusion length ratios to relative defect concentrations and electron capture cross sections. The relative defect concentrations and one of the required capture cross sections are obtained from Deep Level Transient Spectroscopy. Four additional capture cross sections are obtained using diffusion length data and data from temperature dependent lifetime studied. These calculated results are in reasonable agreement with experimental data.

Weinberg, I.↗
NASA NTRS1984

The chemical kinetics and thermodynamics of sodium species in oxygen-rich hydrogen flames

Results are presented which, it is claimed, lead to a correction of previous misconceptions over the relative importance and kinetics of NaO2. It is shown that its rapid conversion to NaO and NaOH is such that it can severely perturb the NaOH/Na ratio and produce significant concentration overshoots over that predicted from the balance of the reaction of Na with H2O. This becomes increasingly the case in flames of large O2 concentrations and temperatures below 2500 K; and the corresponding large rate constants for the termolecular formation of the other alkali peroxides imply that similar considerations will be necessary for them. Depending on the rate constants for the exothermic conversions of MO2 to MO or MOH, the steady-state concentrations of MO2 could be more or less significant than for sodium. Owing to numerous reactions that produce these conversions, the MOH species will probably be the dominant species in all cases in oxygen-rich hydrogen or hydrocarbon flames, with MO concentrations at not greater than 1 percent of the bound metal.

Hynes, A. J.↗
NASA NTRS1985

Microanalysis of dissolved iron and phosphate in pore waters of hypersaline sediment

Diurnal fluctuations of reduced iron concentrations, expected to occur in reduced sediments in the photic zone, were studied. Iron concentration was compared to O2-H2S, a microcanalysis of sulfate reduction was performed, as well as an examination of diurnal concentration of dissolved phosphate and changes in interstitial CO2. The iron profiles suggest a strong correlation between iron remobilization and processes occurring in the light. Phosphate profiles suggest the removal of phosphate is strongly correlated with precipitation of oxidized iron in the upper 2 mm to 5 mm of the sediments. Pore water CO2 concentrations and carbon isotope ratios are presented. These data are from the analyses of minisediment cores collected from the 42 per mil salt pond and incubated in the laboratory under light and dark conditions.

Haddad, R.↗
NASA NTRS1987

Thermoelectric Properties of Lanthanum Sulfide

Report describes measurement of Seebeck coefficient, electrical resistivity, thermal conductivity, and Hall effect in gamma-phase lanthanum sulfide with composition of La3-x S4. Results of study, part of search for high-temperature thermoelectric energy-conversion materials, indicate this sulfide behaves like extrinsic semiconductor over temperature range of 300 to 1,400 K, with degenerate carrier concentration controlled by stoichiometric ratio of La to S.

Wood, C.↗
NASA NTRS1987

A simplified CARS measurement system for rapid determination of temperature and oxygen concentration

A new spectroscopic concept for the rapid determination of temperature and oxygen concentration by CARS (Coherent Anti-Stokes Raman Spectroscopy) was described. The ratio of two spectral regions in the broadband Q-branch spectrum was detected by photomultipliers in a monochromator, which ratio depends on temperature and species concentration. The comparison of the measured data with theory was made using a flat flame burner and an electric furnace, with reasonable results. Various optical techniques for alignment were introduced including a highly efficient, stable dye oscillator. The combination of the spectroscopic concept and the optical techniques will make the CARS measurement system rapid in data processing and simple in optical parts.

Fujii, Shoichi↗
NASA NTRS1988

Antarctic polar stratospheric aerosols: The roles of nitrates, chlorides and sulfates

Nitric and hydrochloric acids have been postulated to condense in the winter polar stratosphere to become an important component of polar stratospheric clouds. One implication is that the removal of NO(y) from the gas phase by this mechanism allows high Cl(x) concentrations to react with O3, because the formation of ClNO3 is inhibited. Contributions of NO3 and Cl to the stratospheric aerosol were determined during the 1987 Airborne Antarctic Ozone Experiment by testing for the presence of nitrates and chlorides in the condensed phase. Aerosol particles were collected on four 500 micron diameter gold wires, each pretreated differently to give results that were specific to certain physical and chemical aerosol properties. One wire was carbon-coated for concentration and size analyses by scanning electron microscopy; X-ray energy dispersive analyses permitted the detection of S and Cl in individual particles. Three more wires were coated with Nitron, barium chloride and silver nitrate, respectively, to detect nitrate, sulfate and chloride in aerosol particles. All three ions, viz., sulfates, nitrates and chlorides were detected in the Antarctic stratospheric aerosol. In terms of number concentrations, the aerosol was dominated by sulfates, followed by chlorides and nitrates. An inverse linear regression can be established between nitrate concentrations and ozone mixing ratio, and between temperature and nitrates.

Pueschel, R. F.↗
NASA NTRS1989

Calibration approach to electron probe microanalysis: A study with PWA-1480, a nickel base superalloy

The utility of an indirect calibration approach in electron probe microanalysis is explored. The methodology developed is based on establishing a functional relationship between the uncorrected k-ratios and the corresponding concentrations obtained using one of the ZAF correction schemes, for all the desired elements in the concentration range of interest. In cases where a very large number of analyses are desired, such a technique significantly reduces the total time required for the microprobe analysis without any significant loss of precision in the data. A typical application of the method in the concentration mapping of the transverse cross-section of a dendrite in directionally solidified PWA-1480, a nickel-based superalloy, is described.

Terepka, F. M.↗
NASA NTRS1994

Prebiotic Oxidative Polymerization of 2,3 Dimercaptopropanol on the Surface of Iron(III) Hydroxide Oxide

The oxidation of 2,3-Dimercapto-1-propanol by ferric ions on the surface of iron (III) hydroxide oxide yielded polydisulfide polymers. This polymerization occured readily at low dithiol concentration under mild aqueous conditions. Polydisulfide polymers up to the 15-mer were synthesized from 1 mM dithiol in 5 ml water reacted with iron (III) hydroxide oxide (20 mg, 160 micro mole Fe) for 3 days under anaerobic conditions at 40 C and pH 4. About 91% of the dithiol was converted to short soluble oligomers and 9% to insoluble larger oligomers that were isolated with the mineral phase. Reactions at higher dithiol concentrations with the same ratio of dithiol to mineral gave a higher yield of the larger insoluble oligomers. The relationship of these results to prebiotic polymer synthesis will be discussed.

Weber, Arthur L.↗