Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cu surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Exceptional NH 3 Detection by Cu(cyhdc) MOF Sensor Due to H 2 O Coadsorption

Metal–organic framework (MOF)-based electrical impedance sensors are a growing class of sensors that show utility in the detection of environmentally toxic gases. Detection of trace NH 3 has been particularly difficult to design due to the low electrical response of NH 3 . However, this has been circumvented by judiciously selecting a MOF that has enhanced electrical response to NH 3 due to coadsorption with predominant atmospheric gases such as water. Herein, an MOF Cu(cyhdc) based sensor has been successfully demonstrated for the enhanced detection of environmentally toxic NH 3 gas. The sensor shows a change in impedance when it is exposed to 5 ppm of NH 3 . At 20 °C, >30% relative humidity (RH) is necessary to elicit a change, with the response increasing with RH and reaching 3170× at 92% RH, producing the largest published response to NH 3 for a MOF direct electrical sensor. In the absence of water, no change is observed toward 5 ppm of NH 3 over 20–50 °C. Here, this electrical response is largely driven by huge decreases in the imaginary component of the impedance, attributed to increased capacitance at the surface of the MOF crystallites upon NH 3 and H 2 O coadsorption. Complementary structural and microstructural characterization proves that the Cu(cyhdc) crystalline structure and morphology remain intact under trace NH 3 and/or H 2 O adsorption. Despite extremely low NH 3 , loadings seen in TGA, XPS, and FT-IR confirm NH 3 and H 2 O adsorption, and changes to the metal-carboxylate IR peak positions are observed upon NH 3 adsorption. Concentrated primarily at the outer surfaces of the MOF crystallites, this NH 3 and H 2 O coadsorption effectively increases the surface capacitance across the Cu(cyhdc) powder and enables direct electrical detection of trace NH 3 . Together, these results demonstrate how coadsorption of specific molecules (H 2 O) can be used to enable the electrical detection of trace toxic gases that would otherwise not have produced a MOF sensor response.

ammonia↗
DOE OSTI2022

Facet Impact of CuMn 2 O 4 Spinel Nanocatalysts on Enhancement of the Oxygen Reduction Reaction in Alkaline Media

Surface-structure engineering represents an attractive strategy to optimize the energy conversion performance of nanocatalysts using their deliberately controlled exposed facets. To further exploit the potential of non-PGM-based spinel catalysts for alkaline oxygen reduction reaction (ORR), a cathodic fuel cell reaction, we hereby report a strategy of ORR improvement by controlling the crystallographic facets of ultra-small CuMn 2 O 4 spinel nanocatalysts through a developed colloidal synthesis approach. The synthesis of CuMn 2 O 4 nanocrystals with morphological control relies on the design and selection of the Cu-/Mn-precursors with striking discrepancies in reaction kinetics. Following carbon loading and an annealing post-treatment of the as-synthesized nanocatalysts, the exclusively {101} facet-exposed CuMn 2 O 4 spinel nano-octahedra exhibit improved electrocatalytic activity toward ORR in 1 M KOH, when compared to their spherical counterparts, exhibiting a mass activity (MA) of 37.6 A/g at 0.85 V. After 10,000 cycles of ORR durability test, the nano-octahedra still retain an MA of 24.5 A/g, which is twice that of the CuMn 2 O 4 spinel nanospheres. Structural characterizations after durability testing indicate that the MA decay is likely associated with a decrease in the Mn 3+ fraction and the emergence of Cu + on CuMn 2 O 4 nano-octahedral surfaces. Finally, as a paradigm, this synthesis approach could be extended to other Mn-based spinel nanocatalysts with precise shape control, enabling us to understand and establish the relationship between the surface lattice/valence state and electrocatalytic properties.

36 MATERIALS SCIENCE↗
DOE OSTI2021

First-principles design of a single-atom–alloy propane dehydrogenation catalyst

The complexity of heterogeneous catalysts means that a priori design of new catalytic materials is difficult, but the well-defined nature of single-atom–alloy catalysts has made it feasible to perform unambiguous theoretical modeling and precise surface science experiments. Herein we report the theory-led discovery of a rhodium-copper (RhCu) single-atom–alloy catalyst for propane dehydrogenation to propene. Although Rh is not generally considered for alkane dehydrogenation, first-principles calculations revealed that Rh atoms disperse in Cu and exhibit low carbon-hydrogen bond activation barriers. Surface science experiments confirmed these predictions, and together these results informed the design of a highly active, selective, and coke-resistant RhCu nanoparticle catalyst that enables low-temperature nonoxidative propane dehydrogenation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

An automated cluster surface scanning method for exploring reaction paths on metal-cluster surfaces

Metal-cluster surfaces present a wide variety of unique coordination environments. This complexity makes it difficult to manually probe the surface reactivity of such clusters. Here, we present a simple and automated method to systematically discover reaction pathways on cluster surfaces, based on the automated cluster surface scanning (ACSS) technique for mapping out potential energy surfaces. We showcase our method on 55-atom icosahedral Cu and Ag clusters, where we determine the activation energies of four elementary steps common in heterogeneous catalysis – hydrogen recombination (H* + H* → H 2 * + *), oxygen recombination (O* + O* → O 2 * + *), water formation (OH* + H* → H 2 O* + *), and CO oxidation (CO* + O* → CO 2 * + *) – with density functional theory calculations (DFT-PBE + D3). We show that the ACSS method requires significantly less human effort than the established manually performed climbing-image nudged elastic band (MP + CI-NEB) technique and locates transition states with comparable accuracy (root-mean-squared error of 0.10 eV) and similar computational cost. Rigorous sampling of the potential energy surface with the ACSS method allows one to locate all lowest-energy reaction pathways obtained via the MP+CI-NEB approach, as well as alternative pathways that one may have missed with the MP+CI-NEB approach due to the many possible pathways available on these clusters. The accuracy and efficiency afforded by the ACSS method could enable high-throughput exploration of the diverse reactivity of metal clusters.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Rational Design and Reticulation of Infinite qbe Rod Secondary Building Units into Metal–Organic Frameworks through a Global Desymmetrization Approach for Inverse C 3 H 8 /C 3 H 6 Separation

Abstract The development of reticular chemistry has enabled the construction of a large array of metal–organic frameworks (MOFs) with diverse net topologies and functions. However, dominating this class of materials are those built from discrete/finite secondary building units (SBUs), yet the designed synthesis of frameworks involving infinite rod‐shaped SBUs remain underdeveloped. Here, by virtue of a global linker desymmetrization approach, we successfully targeted a novel Cu‐MOF (Cu‐ASY) incorporating infinite Cu‐carboxylate rod SBUs with its structure determined by micro electron diffraction (MicroED) crystallography. Interestingly, the rod SBU can be simplified as a unique cylindric sphere packingqbetubule made of [4 3 .6 2 ] tiles, which further connect the tritopic linkers to give a newly discovered 3,5‐connectedgfcnet. Cu‐ASY is a permanent ultramicroporous material featuring 1D channels with highly inert surfaces and shows a preferential adsorption of propane (C 3 H 8 ) over propene (C 3 H 6 ). The efficiency of C 3 H 8 selective Cu‐ASY is validated by multicycle breakthrough experiments, giving C 3 H 6 productivity of 2.2 L/kg. Density functional theory (DFT) calculations reveal that C 3 H 8 molecules form multiple C−H⋅⋅⋅π and atypical C−H⋅⋅⋅ H−C van der Waals interactions with the inner nonpolar surfaces. This work therefore highlights the linker desymmetrization as an encouraging and intriguing strategy for achieving unique MOF structures and properties.

Chemistry↗
NASA NTRS1986

Theoretical studies of diatomic and triatomic systems containing the group IB atoms Cu, Ag, and Au

Selected portions of the ground state potential energy surfaces of the Cu3, Ag3, AgCu2, and AuCu2 trimers are studied at the single-reference singles plus doubles configuration interaction and couple pair functional levels correlating 33 electrons. The calculations use the effective core potentials of Hay and Wadt (1985) to replace the deep core levels. The Cu3 and Ag3 molecules are found to have 2B2 obtuse-angled ground states, with low-lying 2A1 acute-angled excited states. The AgCu2 and AuCu2 molecules have 2A1 acute-angled ground states. The Cu3 molecule has a smaller 3d population than Ag3, and Cu3 has a smaller s electron density in the open-shell orbital than does Ag3, in agreement with recent ESR experiments.

Walch, Stephen P.↗
DOE OSTI2020

Plasma and X-ray radiation-induced damage mechanisms in a tungsten heavy alloy

Tungsten-based materials are among the main candidate plasma-facing materials for future fusion reactors where extreme conditions of thermomechanical stresses, radiation, and energetic particles must be withstood. Here a hybrid X-pinch platform combined with a pulsed power machine was used to study damage mechanisms in 90W–4Cu–6Ni tungsten heavy alloy as a result of exposure to high energy density plasma, X-ray radiation, and the resulting thermal shock. It was found that the plasma-facing surface of the material undergoes severe melting and ablation with the extent of ablation being higher in the Cu–Ni phase than the W particles. Rapid melting and solidification transform the W particles into fine dendrite morphologies embedded in the Cu–Ni solid solution. Cracking was also observed in the subsurface layers at the interfaces between the W particles and the Cu-rich phase of the Cu–Ni matrix. X-ray radiation, on the other hand, cause slight melting on the surface without significant ablation and no cracking.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Computational insights into hydrogen adsorption energies on medium-entropy oxides

High entropy oxides (HEOs) have emerged as promising catalysts for several important chemical transformations including alkane activation. Hydrogen adsorption energy (HAE) has been used as a key descriptor for many reactions including methane C–H activation and hydrogen evolution reactions. Hence, understanding the relationship between HAEs and the surface chemistry of HEO surfaces could lay the foundation for meaningful correlations among methane C–H activation, HAE, and the complex, local environment of HEO surfaces. Here, we used a medium-entropy oxide as a prototypical system – Mg 0.25 Ni 0.25 Cu 0.25 Zn 0.25 O with a rock-salt structure – to interrogate these relationships. We sampled 2000 different surfaces of its (100) plane and calculated the HAEs at randomly chosen surface O sites using density functional theory (DFT). Our analysis of the 2000 data points reveals that the HAEs at the surface O sites are significantly influenced by the local environment around the adsorption sites, particularly the nature of the metal atom directly below the surface O site where H adsorbs. After comparing several popular graph-neural-network-based machine learning models, we found that the DimeNet++ model performed best achieving satisfactory accuracy in predicting HAEs for both Mg 0.25 Ni 0.25 Cu 0.25 Zn 0.25 O and slightly varied compositions. Our work underscores the promise of such models and the need for further refinement to address the complexity of HEOs.

Song, Haohong [Vanderbilt Univ., Nashville, TN (Un↗
DOE OSTI2022

Atomistic modeling of surface and grain boundary dislocation nucleation in FCC metals

Dislocation nucleation plays a critical role in the plastic deformation of crystalline materials. However, it is challenging to predict the active mode and associated rate of dislocation nucleation under typical experimental loading conditions through molecular dynamics simulation due to timescale limitations. In this report we use the free-end nudged elastic band method to determine the activation energies and activation volumes of dislocation nucleation in four typical face-centered cubic metals of Au, Al, Cu and Ni. We focus on the representative processes of surface and grain boundary dislocation nucleation. The atomistically determined activation volumes of these dislocation nucleation processes are larger than 10b3 (with b being the Burgers vector length) under typical experimental loading conditions. These results are compared with experimentally measured activation volumes in ultrafine-grained and nanocrystalline metals, thereby providing mechanistic insight into their rate-controlling deformation mechanisms.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Substrate-Dependent Study of Chain Orientation and Order in Alkylphosphonic Acid Self-Assembled Monolayers for ALD Blocking

For years, many efforts in area selective atomic layer deposition (AS-ALD) have focused on trying to achieve high-quality self-assembled monolayers (SAMs), which have been shown by a number of studies to be effective for blocking deposition. In this work, we show that in some cases where a densely packed SAM is not formed, significant ALD inhibition may still be realized. The formation of octadecylphosphonic acid (ODPA) SAMs was evaluated on four metal substrates: Cu, Co, W, and Ru. The molecular orientation, chain packing, and relative surface coverage were evaluated using near-edge X-ray absorption fine structure (NEXAFS), Fourier transform infrared (FTIR) spectroscopy, and electrochemical impedance spectroscopy (EIS). ODPA SAMs formed on Co, Cu, and W showed strong angular dependence of the NEXAFS signal whereas ODPA on Ru did not, suggesting a disordered layer was formed on Ru. Additionally, EIS and FTIR spectroscopy confirmed that Co and Cu form densely packed, “crystal-like” SAMs whereas Ru and W form less dense monolayers, a surprising result since W-ODPA was previously shown to inhibit the ALD of ZnO and Al 2 O 3 best among all the substrates. This work suggests that multiple factors play a role in SAM-based AS-ALD, not just the SAM quality. Therefore, metrological averaging techniques (e.g., WCA and FTIR spectroscopy) commonly used for evaluating SAMs to predict their suitability for ALD inhibition should be supplemented by more atomically sensitive methods. Finally, it highlights important considerations for describing the mechanism of SAM-based selective ALD.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1991

Crystal growth of YBa2Cu3O(7-x) and reaction of gold crucible with Ba-Cu-rich flux

YBa2Cu3O(7-x) crystals are grown in a gold crucible by a self-flux method. The flux moves along the gold surface due to surface wetting and leaves Y123 crystals behind. The obtained crystals are clean and have a size up to two millimeters and a Tc is greater than 90 K. In an effort to recycle the used crucibles, it is found that the used gold is contaminated by copper. A CuO thin film is easily formed on the surface of the crucible that is made of the used gold. This film provides good surface wetting and a buffer layer, which reduces the reaction between gold and the Y-Ba-Cu-oxide melt.

Tao, Y. K.↗
NASA NTRS2002

Homogenous Surface Nucleation of Solid Polar Stratospheric Cloud Particles

A general surface nucleation rate theory is presented for the homogeneous freezing of crystalline germs on the surfaces of aqueous particles. While nucleation rates in a standard classical homogeneous freezing rate theory scale with volume, the rates in a surface-based theory scale with surface area. The theory is used to convert volume-based information on laboratory freezing rates (in units of cu cm, seconds) of nitric acid trihydrate (NAT) and nitric acid dihydrate (NAD) aerosols into surface-based values (in units of sq cm, seconds). We show that a surface-based model is capable of reproducing measured nucleation rates of NAT and NAD aerosols from concentrated aqueous HNO3 solutions in the temperature range of 165 to 205 K. Laboratory measured nucleation rates are used to derive free energies for NAT and NAD germ formation in the stratosphere. NAD germ free energies range from about 23 to 26 kcal mole, allowing for fast and efficient homogeneous NAD particle production in the stratosphere. However, NAT germ formation energies are large (greater than 26 kcal mole) enough to prevent efficient NAT particle production in the stratosphere. We show that the atmospheric NAD particle production rates based on the surface rate theory are roughly 2 orders of magnitude larger than those obtained from a standard volume-based rate theory. Atmospheric volume and surface production of NAD particles will nearly cease in the stratosphere when denitrification in the air exceeds 40 and 78%, respectively. We show that a surface-based (volume-based) homogeneous freezing rate theory gives particle production rates, which are (not) consistent with both laboratory and atmospheric data on the nucleation of solid polar stratospheric cloud particles.

Tabazadeh, A.↗
NASA NTRS1980

Absolute rate constant of the reaction OH + H2O2 yields HO2 + H2O from 245 to 423 K

The absolute rate constant of the reaction between the hydroxyl radical and hydrogen peroxide was measured by using the discharge-flow resonance fluorescence technique at total pressure between 1 and 4 torr. At 298 K the result is (1.64 + or - 0.32) x 10 to the -12th cu cm/molecule s. The observed rate constant is independent of pressure, surface-to-volume ratio, the addition of vibrational quenchers, and the source of OH. The temperature dependence has also been determined between 245 and 423 K; the resulting Arrhenius expression is k cu cm/molecule s is equal to (2.51 + or - 0.6) x 10 to the -12th exp(-126 + or - 76/T).

Keyser, L. F.↗
NASA NTRS2003

Characterization of Al-Cu-Mg-Ag Alloy RX226-T8 Plate

Aluminum-copper-magnesium-silver (Al-Cu-Mg-Ag) alloys that were developed for thermal stability also offer attractive ambient temperature strength-toughness combinations, and therefore, can be considered for a broad range of airframe structural applications. The current study evaluated Al-Cu-Mg-Ag alloy RX226-T8 in plate gages and compared performance with sheet gage alloys of similar composition. Uniaxial tensile properties, plane strain initiation fracture toughness, and plane stress tearing resistance of RX226-T8 were examined at ambient temperature as a function of orientation and thickness location in the plate. Properties were measured near the surface and at the mid-plane of the plate. Tensile strengths were essentially isotropic, with variations in yield and ultimate tensile strengths of less than 2% as a function of orientation and through-thickness location. However, ductility varied by more than 15% with orientation. Fracture toughness was generally higher at the mid-plane and greater for the L-T orientation, although the differences were small near the surface of the plate. Metallurgical analysis indicated that the microstructure was primarily recrystallized with weak texture and was uniform through the plate with the exception of a fine-grained layer near the surface of the plate. Scanning electron microscope analysis revealed Al-Cu-Mg second phase particles which varied in composition and were primarily located on grain boundaries parallel to the rolling direction. Fractography of toughness specimens for both plate locations and orientations revealed that fracture occurred predominantly by transgranular microvoid coalescence. Introduction High-strength, low-density Al-Cu-Mg-Ag alloys were initially developed to replace conventional 2000 (Al-Cu-Mg) and 7000 (Al-Zn-Cu-Mg) series aluminum alloys for aircraft structural applications [1]. During the High Speed Civil Transport (HSCT) program, improvements in thermal stability were demonstrated for candidate aircraft wing and fuselage skin materials through the addition of silver to Al-Cu-Mg alloys based on Al 2519 chemistry [2]. Thermal stability of the resulting Al-Cu-Mg-Ag alloys, C415-T8 and C416-T8, was due to co-precipitation of the thermally stable . (AlCu) and ' (Al2Cu) strengthening phases [1-4]. The strength and toughness behavior was investigated for these alloys produced as 0.090-inch thick rolled sheet in the T8 condition and after various thermal exposures. The mechanical properties were shown to be competitive with conventional aircraft alloys, 2519-T8 and 2618-T8 [2]. During the Integral Airframe Structure (IAS) program, advanced aluminum alloys were examined for use in an integrally stiffened airframe structure where the skin and stiffeners would be machined from plate and extruded frames would be mechanically attached (see Figure 1) [5]. Advantages of integrally stiffened structure include reduced part count, and reduced assembly times compared to conventional built-up airframe structure. The near-surface properties of a thick plate are of significance for a machined integrally stiffened airframe structure since this represents the skin location. Properties measured at the mid-plane of the plate are more representative of the stiffener web. RX226 was developed to exploit strength-toughness improvements and thermal stability benefits of Al-Cu-Mg-Ag alloys in plate gages. This study evaluated the microstructure and properties of three gages of plate produced in the T8 condition.

Lach, Cynthia L.↗
NASA NTRS1995

Semiempirical Analysis of Surface Alloy Formation

The BFS method for alloys is applied to the study of surface alloy formation. This method was previously used to examine the experimental STM observation of surface alloying of Au on Ni(110) for low Au coverages by means of a numerical simulation. In this work, we extend the study to include other cases of surface alloying for immiscible as well as miscible metals. All binary combinations of Ni, Au, Cu, and Al are considered and the simulation results are compared to experiment when data is available. The driving mechanisms of surface alloy formation are then discussed in terms of the BFS method and the available results.

Bozzolo, Guillermo↗
NASA NTRS1973

Lunar ion energy spectra and surface potential

The acceleration model for lunar ions and the resulting ionosphere dynamics are reviewed briefly. An application is made to lunar atmosphere trapped in the surface fines, and the enhancement in the Ar-40/Ar-36 ratio in samples from the Apennine Front compared to the adjacent mare is calculated to be about 2.0. The predicted lunar ion energy spectra is shown and found to agree well with Suprathermal Ion Detector measurements; from this spectra, the neutral atmosphere scale height can be studied and the neutral atmosphere number density is found to be 100,000 to 300,000 per cu cm at the sunrise and sunset terminators. The lunar surface potential is calculated and is found to be several volts positive over much of the sunlit face of the moon but to go tens of volts negative at the terminator.

Manka, R. H.↗
DOE OSTI2025

Cu–Ni Oxidation Mechanism Unveiled: A Machine Learning-Accelerated First-Principles and in Situ TEM Study

Here, the development of accurate methods for determining how alloy surfaces spontaneously restructure under reactive and corrosive environments is a key, long-standing, grand challenge in materials science. Using machine learning-accelerated density functional theory and rare-event methods, in conjunction with in situ environmental transmission electron microscopy (ETEM), we examine the interplay between surface reconstructions and preferential segregation tendencies of CuNi(100) surfaces under oxidation conditions. Our modeling approach predicts that oxygen-induced Ni segregation in CuNi alloys favors Cu(100)-O c(2 × 2) reconstruction and destabilizes the Cu(100)-O (2√2 × √2)R45° missing row reconstruction (MRR). In situ ETEM experiments validate these predictions and show Ni segregation followed by NiO nucleation and growth in regions without MRR, with secondary nucleation and growth of Cu 2 O in MRR regions. Our approach based on combining disparate computational components and in situ ETEM provides a holistic description of the oxidation mechanism in CuNi, which applies to other alloy systems.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Crosslinked polymeric ionic liquid stationary phases incorporating a combination of silver(I) and copper(II) ions for olefin separations by gas chromatography

The development of efficient and selective olefin separation technologies is a critical challenge within the chemical industry given the high energy demands of conventional cryogenic distillation methods. To address this, the study explores the effectiveness of polymeric ionic liquid (PIL) stationary phases in gas chromatography (GC) that incorporate both silver(I) ([Ag + ]) and copper(II) ([Cu 2+ ]) ions for enhanced olefin separation via π-complexation interactions. Further, the effects of both non-crosslinked and crosslinked PIL stationary phases containing varying ratios of [Ag⁺] and [Cu²⁺] ions were systematically investigated to evaluate their impact on the separation of olefins from paraffins and structurally similar olefins. Retention measurements using a broad range of olefinic probes revealed that [Ag⁺] ions provided stronger and more consistent π-complexation in PIL-based stationary phases, while [Cu²⁺] ions preferentially enhance olefin retention in crosslinked systems. Furthermore, thermal stability studies showed that [Ag + ]-containing PIL stationary phases maintain stable olefin separation efficiency over prolonged exposure under elevated temperatures, while crosslinked PIL stationary phases containing [Cu 2+ ] ions exhibited stronger retention due to increased surface adsorption. These findings provide insight into the tunability of metal–olefin interactions using PIL-based stationary phases and suggest design strategies for achieving thermally stable and highly selective chromatographic separations of unsaturated hydrocarbons.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗