Search NASA⌕ Search

SEARCH · Search NASA

Results for “Direct Processes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Spiral antenna assembly with integrated feed network structure and method of manufacture

A spiral antenna assembly with an integrated feed network and method of manufacturing the same are disclosed. The spiral antenna assembly may comprise a supporting structure integrally formed with a feed network structure, thereby presenting a monolithic structure. A spiral antenna element may be disposed on a bottom surface or a top surface of the supporting structure. The feed network structure may comprise the feed network and project from a center of the top surface of the supporting structure. The feed network may comprise a microstrip balun architecture. The spiral antenna assembly may be formed by additively manufacturing the supporting structure and the feed network structure. A laser direct structuring process may write and activate the spiral antenna element on the supporting structure and the feed network on the feed network structure.

Byers, Kyle J.↗
DOE OSTI2023

Fault Detection in the Solvent Extraction Process with Non-traditional Sensors

Solvent extraction is used to separate metals or other complexes into two different immiscible liquids and is an essential component of the PUREX Process. Improvements to the solvent extraction process can directly contribute to an organization’s ability to ensure the purity and recovery of special nuclear materials from spent nuclear fuel. Such improvements can benefit nuclear reprocessing efforts, increase fuel reutilization, and limit the concentration of actinides in nuclear waste repositories.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2025

Parity-Doubled Nucleons Can Rapidly Cool Neutron Stars

In confined hadronic matter, the spontaneous breaking and restoration of chiral symmetry can be described by considering nucleons, 𝑁 + ⁡(939), and excited states of opposite parity, 𝑁 − ⁡(1535). In a cold, dense hadronic phase where chiral symmetry remains spontaneously broken, direct Urca decay processes involving the 𝑁 − are possible, e.g., 𝑁 − → 𝑁 + + 𝑒 − + $\bar{𝜈}_𝑒$. Here, we show that at low temperature and moderate densities, because the 𝑁 − are much heavier than the 𝑁 + , such cooling dominates over standard 𝑁 + direct Urca processes. This provides a strong astrophysical signature of the pattern of chiral symmetry restoration in neutron stars.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Quantitative Determination of Biomass-derived Renewable Carbon in Fuels from Coprocessing of Bio-oils in Refinery Using a Stable Carbon Isotopic Approach

Increasing renewable carbon incorporation into conventional fuels through coprocessing with vacuum gas oil (VGO, a petroleum refining feedstock) is a critical step in biofuels development, scaling-up, adoption and associated GHG reduction. Optimization of the co-processing parameters maximizes incorporation of the renewable carbon in the fuel products. Quantitative determination of the renewable carbon content in the co-processed products provides direct evaluation of the parameters. The co-processing bio-oil with VGO through hydrocracking (HC) or fluid catalytic cracking (FCC) system resulted in carbon isotopic fractionation that prevented the direct use of the isotope mixing model for quantifying the renewable carbon. Here, we report an algorithm of using a stable carbon isotope approach to quantify the renewable carbon content in co-processing biofuel products through high-precision ?13C analysis. A controlled experiment carried out by blending a fossil diesel (-29.013‰) with a bio-diesel (-30.099‰) at various blending levels up to 98.0/2.0 wt% is presented and has demonstrated the applicability of this approach. The carbon isotope fractionation factors for the bio-oil co-processing were obtained by using a 14C-derived isotope-mixing model. The ?13C method was tested by co-processing 13C-labeled bio-crude and natural woody biomass-derived fast pyrolysis (FP) and catalytic fast pyrolysis (CFP) bio-oils with VGO. The results were verified by 14C accelerator mass spectrometry (AMS) method (ASTM-D6866) and compared with the yield mass balance (YMB) method. Strong agreement between d13C and 14C AMS methods demonstrated the applicability of the ?13C method to quantify renewable carbon content in co-processing fuel products and guide the co-processing optimization

Li, Zhenghua↗
DOE OSTI2023

Understanding structure-processing relationships in metal additive manufacturing via featurization of microstructural images

Understanding and predicting accurate property-structure-processing relationships for additively manufactured components is important for both forward and inverse design of robust, reliable parts and assemblies. While direct mapping of process parameters to properties is sometimes plausible, it is often rendered difficult due to poor microstructural control. Exploring the direct relationship between processing conditions and microstructural features can thus provide significant physical insights and aid the overall design process. Here, in this study, we develop an automated high-throughput framework to simulate an uncertainty-aware additive manufacturing (AM) process, characterize microstructural images, and extract meaningful features/descriptors. A kinetic Monte Carlo (KMC) based model of the AM process is used to simulate microstructural evolution for a diverse set of experimentally relevant processing conditions. We perform a parametric study to explore the relationship between microstructural features and processing conditions. Our results indicate that a many-to-one mapping can exist between processing conditions and typical descriptors; therefore, multiple descriptors are thus necessary to unambiguously represent microstructural images. Our work provides crucial quantitative and qualitative in-formation that would aid in the selection of features for microstructural images. Featurized microstructures could then be utilized to build data-driven models for predictive control of microstructures and thereby properties of additively manufactured components.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Pauli transfer matrix direct reconstruction: channel characterization without full process tomography

Abstract We present a tomographic protocol for the characterization of multiqubit quantum channels. We discuss a specific class of input states, for which the set of Pauli measurements at the output of the channel directly relates to its Pauli transfer matrix components. We compare our results to those of standard quantum process tomography, showing an exponential reduction in the number of different experimental configurations required by a single matrix element extraction, while keeping the same number of shots. This paves the way for more efficient experimental implementations, whenever a selective knowledge of the Pauli transfer matrix is needed. We provide several examples and simulations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Directional Crystallization of Conjugated Molecules during Coating Processes

The coating of organic molecules from the solution phase can result in directional crystal growth under certain conditions, even on a smooth isotropic surface and without the need of any kind of graphoexpitaxial preparation of the substrate. Based on reviewing the results from a variety of coating techniques and coating parameters, we identified that it is crucial for the coating speed to match the growth speed of the fastest growing crystal plane to achieve a high degree of directional crystallization.

36 MATERIALS SCIENCE↗
NASA NTRS1993

Immiscible phase incorporation during directional solidification of hypermonotectics

Solidification processes in immiscible samples were investigated by directly observing the events taking place at the solid-liquid interface during directional solidification. Visualization of these events was made possible through the use of a transparent metal analog system and a temperature gradient stage assembly fitted to an optical microscope. The immiscible transparent analog system utilized was the succinonitrile-glycerol system. This system has been shown to exhibit the same morphological transitions as observed in metallic alloys of monotectic composition. Both monotectic and hypermonotectic composition samples were directionally solidified in order to gain an improved understanding of the manner in which the excess hypermonotectic liquid is incorporated into the solidifying structure. The processing conditions utilized prevented sedimentation of the excess hypermonotectic liquid by directionally solidifying the samples in very thin (13 microns), horizontally oriented cells. High thermal gradient to growth rate ratios (G/R) were used in an effort to prevent constitutional supercooling and the subsequent formation of L(sub 2) droplets in advance of the solidification front during the growth of fibrous composite structures. Results demonstrated that hypermonotectic composites could be produced in samples up to two weight percent off of the monotectic composition by using a G/R ratio greater than or equal to 4.6 x 10(exp 4) C(s)/mm(sup 2) to avoid constitutional supercooling. For hypermonotectic samples processed with G/R ratios below 4.6 x 10(exp 4) C(s)/mm(sup 2), constitutional supercooling occurred and resulted in slight interfacial instability. For these samples, two methods of incorporation of the hypermonotectic liquid were observed and are reported. The correlation between the phase spacing, lambda, and the growth rate, R, was examined and was found to obey a relationship generally associated with a diffusion controlled coupled growth process. For samples with compositions ranging from the monotectic composition up to 2 percent off of the monotectic composition, data indicated that the square of the phase spacing (lambda) varied linearly with the inverse of the growth rate (R).

Andrews, J. Barry↗
DOE OSTI2022

Direct Recycling of Lithium-Ion Battery Cathodes: A Multi-Stage Annealing Process to Recover the Pristine Structure and Performance

Direct recycling is an alternative low-cost process that retains the structure of the lithium-ion battery cathode rather than going through materials dissolution and repurification. While the process shows promise, various steps need to be better understood and studied to identify possible roadblocks, cost intensive steps, and needed variations in protocol that may be necessary based on the feedstock of recycled cathodes available. In this study, we have evaluated the process of thermal relithiation as it applies to end-of-life cathode materials. For recovered end-of-life cathodes, approximately 20% of the useable lithium has been lost due to solid electrolyte interface formation, parasitic reactions, and particle isolation; this lost lithium contributes to higher cell impedance and a gradual shift in electrode potentials. As a first step in the direct recycling process, this lithium needs to be restored not only to recover capacity but also to eliminate surface vacancies and hinder surface reconstruction that may increase impedance and impact performance. Here, we have optimized a coating method followed by a two-stage annealing process that restores a model delithiated NMC333 material to pristine performance. Comparisons to single-stage processes are made, and new characterization tools have been used to better understand the processes.

25 ENERGY STORAGE↗
DOE OSTI2020

Current challenges and potential directions towards precision microscale additive manufacturing – Part III: Energy induced deposition and hybrid electrochemical processes

The Part III of the four-part series of articles discusses the challenges and opportunities in microscale additive manufacturing processes, specifically focusing on energy-induced deposition and electrochemical processes. Compared to the direct ink write (DIW) and laser-based processes, the energy-induced deposition methods can fabricate high-resolution, high aspect ratio and complex parts, while the hybrid electrochemical process can be used to fabricate complex parts using a wide range of conductive and photoactive materials. However, the volumetric throughput of these processes is lower than their DIW and laser-based counterparts. The processes that have been explored in this process are Focused-ion Beam Induced Deposition (FIBID), Laser Chemical Vapor Deposition (LCVD), Menicus-confined Electrodeposition (MCED) and Laser-Enabled Electrochemical Printing (LECP). The range of processable materials, feature-size resolution, geometry and volumetric throughput are used as factors to evaluate the current state-of-the-art for these processes. Finally, novel approaches have been proposed in the article to address these challenges associated with microscale AM processes.

42 ENGINEERING↗
DOE OSTI2022

Research needs targeting direct air capture of carbon dioxide: Material & process performance characteristics under realistic environmental conditions

The extraction of CO 2 from ambient air, or direct air capture (DAC), is a crucial negative CO 2 emissions technology with great potential for contributing to the mitigation of global warming and climate change. Furthermore, nearly all published research on DAC has been conducted under indoor temperature conditions, i.e. 20 to 30 °C. In contrast, the future global implementation of DAC requires it to be operational across a wide expanse of geographical areas, of which the local temperatures can vary between -30 to 50 °C. Similarly, the absolute humidity can vary from ~0 to 84 g/m 3 in various locations. Due to the massive amount of air that would be processed, it may be impractical to preheat or dehumidify the air before the CO 2 separation. Therefore, it is important to develop DAC materials with good performance at realistic outdoor conditions, especially at sub-ambient conditions, i.e. -30 to 20 °C. In addition to material development, system-level studies at sub-ambient conditions are also needed for the DAC processes to reach optimal designs, which may be very different from those at ambient conditions. In this perspective article, we first assess the literature to identify the technical gaps that need to be filled for DAC to be applicable at realistic outdoor conditions. We then suggest additional research directions needed for DAC to be viable under varied conditions from the perspectives of materials and system designs. For materials, we discuss the expected physical and chemical property changes for the sorbents when the temperature or humidity reaches extremes within their range, and how that will impact performance. Similarly, for system design, we indicate how varied conditions will impact performance and how these changes will impact process optimization.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2023

Process-structure-property considerations for wire-based directed energy deposition of Ti-6Al-4V

Directed energy deposition (DED) is an attractive additive manufacturing (AM) process for large structural components. The rapid solidification and layer-by-layer process associated with DED results in non-ideal microstructures, such as large grains with strong crystallographic textures. These non-ideal microstructures can lead to severe anisotropy in the mechanical properties. Despite these challenges, DED has been identified as a potential solution for the manufacturing of near net shape Ti-6Al-4V preforms, replacing lost casting and forging capabilities. Two popular wire-based directed energy deposition (W-DED) processes were considered for the manufacturing of Ti-6Al-4V with assessments on their respective metallurgical and mechanical properties, as compared to a conventionally processed material. The two W-DED processes explored were wire arc additive manufacturing (WAAM) and electron beam additive manufacturing (EBAM). High throughput inspection and tensile testing procedures were utilized to generate statistically relevant data sets related to each process and sample orientation. The 2 AM technologies produced material with remarkably different microstructures and mechanical properties. Importantly, results revealed key differences in strength and ductility for the two disparate processes which were found to be related to differences in the metallurgical properties.

36 MATERIALS SCIENCE↗
NASA NTRS2006

NASA-STD-(I)-6016, Standard Materials and Processes Requirements for Spacecraft

This document is directed toward Materials and Processes (M&P) used in the design, fabrication, and testing of flight components for all NASA manned, unmanned, robotic, launch vehicle, lander, in-space and surface systems, and spacecraft program/project hardware elements. All flight hardware is covered by the M&P requirements of this document, including vendor designed, off-the-shelf, and vendor furnished items. Materials and processes used in interfacing ground support equipment (GSE); test equipment; hardware processing equipment; hardware packaging; and hardware shipment shall be controlled to prevent damage to or contamination of flight hardware.

Pedley, Michael↗
DOE OSTI2025

Addressing Inherent Challenges to Chemical Relithiation of Cycled End‐of‐Life Cathode Materials

Recycling end‐of‐life (EOL) lithium‐ion batteries (LIBs) is important to retain valuable resources from critical materials present in EOL battery waste. Direct recycling methods offer an opportunity to recover intact valuable cathode materials with minimal re‐processing. An important step of the direct recycling process is relithiation which is used to restore lithium content to EOL cathode materials. However, little has been done to study how preprocessing steps such as washing or binder removal may affect relithiation methods in the direct recycling process. Here, the evolution of fluorine byproducts left over from preprocessing steps during a low‐temperature chemical redox mediator relithiation process is tracked. A facile washing step is presented as a solution for mediating adverse effects of surface contamination on the chemical relithiation performance. The structure, lithium content, and electrochemical performance of relithiated EOL NMC 622 material that underwent a pre‐relithiation washing step to remove fluorine byproducts is shown to match that of pristine NMC 622. In this work, it is showed that redox mediator relithiation as a part of a direct recycling process is a promising low energy method that can be applied to EOL material with inherent surface impurities if the proper pre‐relithiation processing steps are implemented.

25 ENERGY STORAGE↗
DOE OSTI2022

Deep Learning for In-Situ Layer Quality Monitoring during Laser-Based Directed Energy Deposition (LB-DED) Additive Manufacturing Process

Defects are a leading issue for the rejection of parts manufactured through the Directed Energy Deposition (DED) Additive Manufacturing (AM) process. In an attempt to illuminate and advance in situ quality monitoring and control of workpieces, we present an innovative data-driven method that synchronously collects sensing data and AM process parameters with a low sampling rate during the DED process. The proposed data-driven technique determines the important influences that individual printing parameters and sensing features have on prediction at the inter-layer qualification to perform feature selection. Three Machine Learning (ML) algorithms including Random Forest (RF), Support Vector Machine (SVM), and Convolutional Neural Network (CNN) are used. During post-production, a threshold is applied to detect low-density occurrences such as porosity sizes and quantities from CT scans that render individual layers acceptable or unacceptable. This information is fed to the ML models for training. Training/testing are completed offline on samples deemed “high-quality” and “low-quality”, utilizing only features recorded from the build process. CNN results show that the classification of acceptable/unacceptable layers can reach between 90% accuracy while training/testing on a “high-quality” sample and dip to 65% accuracy when trained/tested on “low-quality”/“high-quality” (respectively), indicating over-fitting but showing CNN as a promising inter-layer classifier.

36 MATERIALS SCIENCE↗