Results for “FUNCTIONAL TYPES” — Page 27

NASA NTRS1987

A model for the influence of pressure on the bulk modulus and the influence of temperature on the solidification pressure for liquid lubricants

Two pressure chambers, for compression experiments with liquids from zero to 2.2 GPa pressure, are described. The experimentally measured compressions are then compared to theoretical values given by an isothermal model of equation of state recently introduced for solids. The model describes the pressure and bulk modulus as a function of compression for different types of lubricants with a very high accuracy up to the pressure limit of the high pressure chamber used (2.2 GPa). In addition the influence of temperature on static solidification pressure was found to be a simple function of the thermal expansion of the fluid.

Jacobson, Bo O.↗

NASA NTRS2002

Solar Flares, Type III Radio Bursts, Coronal Mass Ejections, and Energetic Particles

In this correlative study between greater than 20 MeV solar proton events, coronal mass ejections (CMEs), flares, and radio bursts it is found that essentially all of the proton events are preceded by groups of type III bursts and all are preceded by CMEs. These type III bursts (that are a flare phenomenon) usually are long-lasting, intense bursts seen in the low-frequency observations made from space. They are caused by streams of electrons traveling from close to the solar surface out to 1 AU. In most events the type III emissions extend into, or originate at, the time when type II and type IV bursts are reported (some 5 to 10 minutes after the start of the associated soft X-ray flare) and have starting frequencies in the 500 to approximately 100 MHz range that often get lower as a function of time. These later type III emissions are often not reported by ground-based observers, probably because of undue attention to type II bursts. It is suggested to call them type III-1. Type III-1 bursts have previously been called shock accelerated (SA) events, but an examination of radio dynamic spectra over an extended frequency range shows that the type III-1 bursts usually start at frequencies above any type II burst that may be present. The bursts sometimes continue beyond the time when type II emission is seen and, furthermore, sometimes occur in the absence of any type II emission. Thus the causative electrons are unlikely to be shock accelerated and probably originate in the reconnection regions below fast CMEs. A search did not find any type III-1 bursts that were not associated with CMEs. The existence of low-frequency type III bursts proves that open field lines extend from within 0.5 radius of the Sun into the interplanetary medium (the bursts start above 100 MHz, and such emission originates within 0.5 solar radius of the solar surface). Thus it is not valid to assume that only closed field lines exist in the flaring regions associated with CMEs and some interplanetary particles originating in such flare regions might be expected in all solar particle events.

Cane, Hilary V.↗

NASA NTRS1982

Asymptotic freedom in solids - A theorem

A cusp theorem is proved that relates the zero-separation value and slope of two-particle position correlation functions in quantum many-body systems with Coulombic interactions. The theorem is independent of the particle type and symmetry of the wave function. Its proof uses only the integral form of the Schroedinger equation and the continuity and exponential decay of the wave function. It is used to derive a sum rule for the electron-gas structure factor and an exact statement about the screening of point charges. Applications to atomic-orbital-based calculations for H2 and metallic H are described.

Carlsson, A. E.↗

NASA NTRS1999

Alterations in Skeletal Muscle Function with Microgravity, and the Protective Effects of High Resistance Isometric and Isotonic Exercise

Exposure to microgravity or models designed to mimic the unloaded condition, such as bed rest in humans and hindlimb unloading (HU) in rats leads to skeletal muscle atrophy, a loss in peak force and power, and an increased susceptibility to fatigue. The posterior compartment muscles of the lower leg (calf muscle group) appear to be particularly susceptible. Following only 1 wk in space or HU, rat soleus muscle showed a 30 to 40% loss in wet weight. After 3 wk of HU, almost all of the atrophied soleus fibers showed a significant increase in maximal shortening velocity (V(sub 0)), while only 25 to 30 % actually transitioned to fast fibers. The increased V(sub 0), was protective in that it reduced the decline in peak power associated with the reduced peak force. When the soleus is stimulated in situ following HU or zero-g one observes an increased rate and extent of fatigue, and in the former the increased fatigue is associated with a more rapid depletion of muscle glycogen and lactate production. Our working hypothesis is that following HU or spaceflight in rats and bed rest or spaceflight in humans limb skeletal muscles during contractile activity depend more on carbohydrates and less on fatty acids for their substrate supply. Baldwin et al. found 9 days of spaceflight to reduce by 37% the ability of both the high and low oxidative regions of the vastus muscle to oxidize long-chain fatty acids. This decline was not associated with any change in the enzymes of the tricarboxylic acid cycle or oxidation pathway. The purpose of the current research was to establish the extent of functional change in the slow type I and fast type H fibers of the human calf muscle following 17 days of spaceflight, and determine the cellular mechanisms of the observed changes. A second goal was to study the effectiveness of high resistance isotonic and isometric exercise in preventing the deleterious functional changes associated with unloading.

Fitts, R. H.↗

NASA NTRS1977

Electrical 2-omega-cm 0.046-cm-thick silicon solar cells as a function of intensity and temperature

Electrical characteristics of Mariner '71 type silicon solar cells are presented in graphical and tabular format as a function of intensity and temperature.

Berman, P. A.↗

NASA NTRS2016

The Application of Hardware in the Loop Testing for Distributed Engine Control

The essence of a distributed control system is the modular partitioning of control function across a hardware implementation. This type of control architecture requires embedding electronics in a multitude of control element nodes for the execution of those functions, and their integration as a unified system. As the field of distributed aeropropulsion control moves toward reality, questions about building and validating these systems remain. This paper focuses on the development of hardware-in-the-loop (HIL) test techniques for distributed aero engine control, and the application of HIL testing as it pertains to potential advanced engine control applications that may now be possible due to the intelligent capability embedded in the nodes.

Distributed Engine Control↗

NASA NTRS2016

The Application of Hardware in the Loop Testing for Distributed Engine Control

The essence of a distributed control system is the modular partitioning of control function across a hardware implementation. This type of control architecture requires embedding electronics in a multitude of control element nodes for the execution of those functions, and their integration as a unified system. As the field of distributed aeropropulsion control moves toward reality, questions about building and validating these systems remain. This paper focuses on the development of hardware-in-the-loop (HIL) test techniques for distributed aero engine control, and the application of HIL testing as it pertains to potential advanced engine control applications that may now be possible due to the intelligent capability embedded in the nodes.

Control↗

NASA NTRSDate not supplied

Quantifying Post-fire Vegetation Recovery on the Colorado Front Range

Forest composition and structure in the Colorado Front Range has been altered by changing wildfire regimes, particularly in response to increased fire severity. Subsequent reductions in post-fire tree regeneration can result in chronic impacts to ecological function and water quality. This project partnered with the U.S. Forest Service to estimate tree canopy recovery from 15 to 21 years after four Colorado Front Range fires that burned between 1996 and 2002— the Bobcat, Buffalo Creek, Hayman, and High Meadows fires—using Landsat 5 Thematic Mapper (TM), Landsat 7 Enhanced Thematic Mapper (ETM+), and Landsat 8 Operational Land Imager (OLI). First, we evaluated relationships between recovery metrics derived from spectral vegetation indices (i.e. post-fire vegetation, normalized burn ratio, percent unrecovered vegetation) and field-collected counts of post-fire tree seedling regeneration. Then, we used high-resolution imagery paired with Landsat timeseries spectral and geomorphometric data to map forest canopy cover 15-21 years post-fire. Finally, we assessed ecological drivers of recovery including topography, climate, soils, and fire severity using Random Forest. While we found that basic vegetation index metrics failed to distinguish field-measured tree regeneration, our data showed that both aspect and burn severity were important drivers of vegetation recovery. North-facing aspects tended to have higher pre-fire Normalized Difference Vegetation Index (NDVI) and thus higher burn severities. However, areas that burned at high severity experienced slower vegetation recovery, regardless of aspect suggesting that high severity fire can mute favorable site conditions on north-facing aspects (i.e. moister, more developed soils). While this work propels our understanding of variables that influence vegetative recovery, vegetation type, forest conversion, and watershed function, more work should focus on what vegetation indices identifying areas of recovery indicate across different forest types and burn severities.

NASA DEVELOP↗

NASA NTRS1984

Discrete approximation methods for parameter identification in delay systems

Approximation schemes for parameter identification problems in which the governing state equation is a linear functional differential equation of retarded type are constructed. The basis of the schemes is the replacement of the parameter identification problem having an infinite dimensional state equation by a sequence of approximating parameter identification problems in which the states are given by finite dimensional discrete difference equations. The difference equations are constructed using linear semigroup theory and rational function approximations to the exponential. Sufficient conditions are given for the convergence of solutions to the approximating problems, which can be obtained using conventional methods, to solutions to the original parameter identification problem. Finite difference and spline based schemes using Paderational function approximations to the exponential are constructed, and shown to satisfy the sufficient conditions for convergence. A discussion and analysis of numerical results obtained through the application of the schemes to several examples is included.

Rosen, I. G.↗

NASA NTRS2013

High Bypass Ratio Jet Noise Reduction and Installation Effects Including Shielding Effectiveness

An experimental investigation was performed to study the propulsion airframe aeroacoustic installation effects of a separate flow jet nozzle with a Hybrid Wing Body aircraft configuration where the engine is installed above the wing. Prior understanding of the jet noise shielding effectiveness was extended to a bypass ratio ten application as a function of nozzle configuration, chevron type, axial spacing, and installation effects from additional airframe components. Chevron types included fan chevrons that are uniform circumferentially around the fan nozzle and T-fan type chevrons that are asymmetrical circumferentially. In isolated testing without a pylon, uniform chevrons compared to T-fan chevrons showed slightly more low frequency reduction offset by more high frequency increase. Phased array localization shows that at this bypass ratio chevrons still move peak jet noise source locations upstream but not to nearly the extent, as a function of frequency, as for lower bypass ratio jets. For baseline nozzles without chevrons, the basic pylon effect has been greatly reduced compared to that seen for lower bypass ratio jets. Compared to Tfan chevrons without a pylon, the combination with a standard pylon results in more high frequency noise increase and an overall higher noise level. Shielded by an airframe surface 2.17 fan diameters from nozzle to airframe trailing edge, the T-fan chevron nozzle can produce reductions in jet noise of as much as 8 dB at high frequencies and upstream angles. Noise reduction from shielding decreases with decreasing frequency and with increasing angle from the jet inlet. Beyond an angle of 130 degrees there is almost no noise reduction from shielding. Increasing chevron immersion more than what is already an aggressive design is not advantageous for noise reduction. The addition of airframe control surfaces, including vertical stabilizers and elevon deflection, showed only a small overall impact. Based on the test results, the best overall nozzle configuration design was selected for application to the N2A Hybrid Wing Body concept that will be the subject of the NASA Langley 14 by 22 Foot Subsonic Tunnel high fidelity aeroacoustic characterization experiment. The best overall nozzle selected includes T-fan type chevrons, uniform chevrons on the core nozzle, and no additional pylon of the type that created a strong acoustic effect at lower bypass ratios. The T-fan chevrons are oriented azimuthally away from the ground observer locations. This best overall nozzle compared to the baseline nozzle was assessed, at equal thrust, to produce sufficient installed noise reduction of the jet noise component to enable the N2A HWB to meet NASA s noise goal of 42 dB cumulative below Stage 4.

Thomas, Russell H.↗

NASA NTRS2012

The Role of Aerosols on Precipitation Processes: Cloud Resolving Model Simulations

Cloud microphysics is inevitably affected by the smoke particle (CCN, cloud condensation nuclei) size distributions below the clouds. Therefore, size distributions parameterized as spectral bin microphysics are needed to explicitly study the effects of atmospheric aerosol concentration on cloud development, rainfall production, and rainfall rates for convective clouds. Recently, a detailed spectral-bin microphysical scheme was implemented into the Goddard Cumulus Ensemble (GCE) model. The formulation for the explicit spectral bin microphysical processes is based on solving stochastic kinetic equations for the size distribution functions of water droplets (i.e., cloud droplets and raindrops), and several types of ice particles [i.e. pristine ice crystals (columnar and plate-like), snow (dendrites and aggregates), graupel and frozen drops/hail]. Each type is described by a special size distribution function containing many categories (i.e., 33 bins). Atmospheric aerosols are also described using number density size-distribution functions. The model is tested by studying the evolution of deep cloud systems in the west Pacific warm pool region, the sub-tropics (Florida) and midlatitudes using identical thermodynamic conditions but with different concentrations of CCN: a low "clean" concentration and a high "dirty" concentration. Results indicate that the low CCN concentration case produces rainfall at the surface sooner than the high CeN case but has less cloud water mass aloft. Because the spectral-bin model explicitly calculates and allows for the examination of both the mass and number concentration of species in each size category, a detailed analysis of the instantaneous size spectrum can be obtained for these cases. It is shown that since the low (CN case produces fewer droplets, larger sizes develop due to greater condensational and collection growth, leading to a broader size spectrum in comparison to the high CCN case. Sensitivity tests were performed to identify the impact of ice processes, radiation and large-scale influence on cloud-aerosol interactive processes, especially regarding surface rainfall amounts and characteristics (i.e., heavy or convective versus light or stratiform types). In addition, an inert tracer was included to follow the vertical redistribution of aerosols by cloud processes. We will also give a brief review from observational evidence on the role of aerosol on precipitation processes.

Tao, Wei-Kuo↗

NASA NTRS1960

Analog Techniques for Measuring the Frequency Response of Linear Physical Systems Excited by Frequency-Sweep Inputs

Data-reduction methods using general-purpose analog computer equipment and compatible testing techniques for determining the frequency response of linear physical systems are examined. The techniques considered may be classed as steady state or transient depending on the method of excitation. The relative merits of periodic, slow sweep, and transient (rapid sweep) forcing functions are discussed and applications are given that relate to dynamic-response tests of aeroelastic systems. Two frequency-sweep-input methods are considered in detail. one case the sweep rate is sufficiently slow that the response is approximately the same as that for steady-state conditions. With this input the frequency response can be evaluated and displayed in real time while the test is in progress. Errors due to treating sweep data as steady state can be eliminated, when desired, by reanalyzing tape-recorded time histories of the input and output as transient rather than as periodic data. In the second method the frequency-response function is deter- mined from the system's transient response to a very rapid sweep input. The purpose of frequency sweep in this case is to provide sufficient harmonic content in the input to overcome noise while keeping the test time as short as possible. tests and limited flight-test data presented herein, it appears that a transient-type rapid-sweep forcing function offers a considerable saving in test time while preserving the accuracy possible with steady-state sinusoidal inputs.

Wilmer H. Reed III↗

NASA NTRS2019

Structure Deformation Calculation Program Based on Displacement Theory for Shape Predictions

Separated programs were written in C/C++ to validate the Displacement Transfer Functions. The Structure Deformation Calculation Program was written to combine all of the programs to calculate deformed shapes of a structure using surface strain data and structural geometrical parameters. Users do not need to know the material properties, nor the complex internal structures geometry because the Displacement Theory is purely geometrical in nature. Users only need to know the structure types as defined in this report and information such as the structure length, depth factors, number of strain sensors, and the surface strains measured at the strain-sensing stations installed on the structures. Depending on the structure type, an applicable Displacement Transfer Function will be used. This program requires two input files created by users; the recorded strain data file in comma-separated values format and the structure geometry data file in text format. The program will output the out-of-plane deflections, slopes, cross-sectional twist angles, and depth factors if applicable. All output files are created in comma-separated values format. A section in this report describes step-by-step procedures on how to use the Structure Deformation Calculation Program for structure deformed shape calculations.

Displacement theory↗

NASA NTRS2003

The Impact of Aerosols on Cloud and Precipitation Processes: Cloud-Resolving Model Simulations

Cloud microphysics are inevitably affected by the smoke particle (CCN, cloud condensation nuclei) size distributions below the clouds. Therefore, size distributions parameterized as spectral bin microphysics are needed to explicitly study the effects of atmospheric aerosol concentration on cloud development, rainfall production, and rainfall rates for convective clouds. Recently, two detailed spectral-bin microphysical schemes were implemented into the Goddard Cumulus Ensemble (GCE) model. The formulation for the explicit spectral-bin microphysical processes is based on solving stochastic kinetic equations for the size distribution functions of water droplets (i.e., cloud droplets and raindrops), and several types of ice particles [i.e.,pristine ice crystals (columnar and plate-like), snow (dendrites and aggregates), graupel and frozen drops/hail]. Each type is described by a special size distribution function containing many categories (i.e. 33 bins). Atmospheric aerosols are also described using number density size-distribution functions.A spectral-bin microphysical model is very expensive from a from a computational point of view and has only been implemented into the 2D version of the GCE at the present time. The model is tested by studying the evolution of deep tropical clouds in the west Pacific warm pool region using identical thermodynamic conditions but with different concentrations of CCN: a low "clean" concentration and a high "dirty" concentration. Besides the initial differences in aerosol concentration, preliminary results indicate that the low CCN concentration case produces rainfall at the surface sooner than the high CCN case but has less cloud water mass aloft. Because the spectral-bin model explicitly calculates and allows for the examination of both the mass and number concentration of species in each size categor, a detailed analysis of the instantaneous size spectrum can be obtained for the two cases. It is shown that since the low CCN case produces fewer droplets, larger sized develop due to the greater condensational and collectional growth, leading to a broader size spectrum in comparison to the high CCN case.

Tao, Wei-Kuo↗

NASA NTRS2003

The Impact of Aerosols on Cloud and Precipitation Processes: Cloud-Resolving Model Simulations

Cloud microphysics are inevitable affected by the smoke particle (CCN, cloud condensation nuclei) size distributions below the clouds. Therefore, size distribution parameterized as spectral bin microphysics are needed to explicitly study the effect of atmospheric aerosol concentration on cloud development, rainfall production, and rainfall rates convective clouds. Recently, two detailed spectral-bin microphysical schemes were implemented into the Goddard Cumulus Ensembel (GCE) model. The formulation for the explicit spectral-bim microphysical processes is based on solving stochastic kinetic equations for the size distribution functions of water droplets (i.e., cloud droplets and raindrops), and several types of ice particles [i.e., pristine ice crystals (columnar and plate-like), snow (dendrites and aggregates), groupel and frozen drops/hall] Each type is described by a special size distribution function containing many categories (i.e., 33 bins). Atmospheric aerosols are also described using number density size-distribution functions.A spectral-bin microphysical model is very expensive from a computational point of view and has only been implemented into the 2D version of the GCE at the present time. The model is tested by studying the evolution of deep cloud systems in the west Pacific warm pool region and in the mid-latitude using identical thermodynamic conditions but with different concentrations of CCN: a low "clean" concentration and a high "dirty" concentration. Besides the initial differences in aerosol concentration, preliminary results indicate that the low CCN concentration case produces rainfall at the surface sooner than the high CCN case but has less cloud water mass aloft. Because the spectral-bim model explicitly calculates and allows for the examination of both the mass and number concentration of cpecies in each size category, a detailed analysis of the instantaneous size spectrum can be obtained for the two cases. It is shown that since the low CCN case produces fever droplets, larger size develop due to greater condencational and collectional growth, leading to a broader size spectrum in comparison to the high CCN case.

Tao, Wei-Kuo↗

NASA NTRS2004

The Impact of Aerosols on Cloud and Precipitation Processes: Cloud-resolving Model Simulations

Cloud microphysics is inevitably affected by the smoke particle (CCN, cloud condensation nuclei) size distributions below the clouds. Therefore, size distributions parameterized as spectral bin microphysics are needed to explicitly study the effects of atmospheric aerosol concentration on cloud development, r d a U production, and rainfall rates for convective clouds. Recently, two detailed spectral-bin microphysical schemes were implemented into the Goddard Cumulus Ensembe1 (GCE) model. The formulation for the explicit spectral-bin microphysical processes is based on solving stochastic kinetic equations for the size distribution functions of water droplets (i.e., cloud droplets and raindrops), and several types of ice particles [i.e. pristine ice crystals (columnar and platelike), snow (dendrites and aggregates), graupel and frozen drops/hail]. Each type is described by a special size distribution function containing many categories (i.e. 33 bins). Atmospheric aerosols are also described using number density size-distribution functions. A spectral-bin microphysical model is very expensive from a computational point of view and has only been implemented into the 2D version of the GCE at the present time. The model is tested by studying the evolution of deep tropical clouds in the west Pacific warm pool region and in the mid-latitude continent with different concentrations of CCN: a low "c1ean"concentration and a high "dirty" concentration. In addition, differences and similarities between bulk microphysics and spectral-bin microphysical schemes will be examined and discussed.

Tao, Wei-Kuo↗

NASA NTRS2004

The Impact of Aerosols on Cloud and Precipitation Processes: Cloud-Resolving Model Simulations

Cloud microphysics is inevitably affected by the smoke particle (CCN, cloud condensation nuclei) size distributions below the clouds. Therefore, size distributions parameterized as spectral bin microphysics are needed to explicitly study the effects of atmospheric aerosol concentration on cloud development, rainfall production, and rainfall rates for convective clouds. Recently, two detailed spectral-bin microphysical schemes were implemented into the Goddard Cumulus Ensembel (GCE) model. The formulation for the explicit spectral-bin microphysical processes is based on solving stochastic kinetic equations for the size distribution functions of water droplets (i.e., cloud droplets and raindrops), and several types of ice particles [i.e. pristine ice crystals (columnar and plate-like), snow (dendrites and aggregates), graupel and frozen drops/hail]. Each type is described by a special size distribution function containing many categories (i.e. 33 bins). Atmospheric aerosols are also described using number density size distribution functions. A spectral-bin microphysical model is very expensive from a computational point of view and has only been implemented into the 2D version of the GCE at the present time. The model is tested by studying the evolution of deep tropical clouds in the west Pacific warm pool region and in the mid-latitude continent with different concentrations of CCN: a low "c1ean"concentration and a high "dirty" concentration. In addition, differences and similarities between bulk microphysics and spectral-bin microphysical schemes will be examined and discussed.

Tao, Wei-Kuo↗

NASA NTRS2004

The Impact of Aerosols on Cloud and Precipitation Processes: Cloud-Resolving Model Simulations

Cloud microphysics are inevitably affected by the smoke particle (CCN, cloud condensation nuclei) size distributions below the clouds. Therefore, size distributions parameterized as spectral bin microphysics are needed to explicitly study the effects of atmospheric aerosol concentration on cloud development, rainfall production, and rainfall rates for convective clouds. Recently, two detailed spectral-bin microphysical schemes were implemented into the Goddard Cumulus Ensemble (GCE) model. The formulation for the explicit spectral-bin microphysical processes is based on solving stochastic kinetic equations for the size distribution functions of water droplets (i.e., cloud droplets and raindrops), and several types of ice particles (i.e., pristine ice crystals (columnar and plate-like), snow (dendrites and aggregates), graupel and frozen drops/hail). Each type is described by a special size distribution function containing many categories (i.e. 33 bins). Atmospheric aerosols are also described using number density size-distribution functions. A spectral-bin microphysical model is very expensive from a computational point of view and has only been implemented into the 2D version of the GCE at the present time. The model is tested by studying the evolution of deep cloud systems in the west Pacific warm pool region, in the sub-tropics (Florida) and in the mid-latitude using identical thermodynamic conditions but with different concentrations of CCN: a low 'clean' concentration and a high 'dirty' concentration.

Tao, Wei-Kuo↗