Results for “Finite elements” — Page 27

NASA NTRS1978

Finite element dynamic analysis on CDC STAR-100 computer

Computational algorithms are presented for the finite element dynamic analysis of structures on the CDC STAR-100 computer. The spatial behavior is described using higher-order finite elements. The temporal behavior is approximated by using either the central difference explicit scheme or Newmark's implicit scheme. In each case the analysis is broken up into a number of basic macro-operations. Discussion is focused on the organization of the computation and the mode of storage of different arrays to take advantage of the STAR pipeline capability. The potential of the proposed algorithms is discussed and CPU times are given for performing the different macro-operations for a shell modeled by higher order composite shallow shell elements having 80 degrees of freedom.

Noor, A. K.↗

NASA NTRS1988

A preliminary investigation of finite-element modeling for composite rotor blades

The results from an initial phase of an in-house study aimed at improving the dynamic and aerodynamic characteristics of composite rotor blades through the use of elastic couplings are presented. Large degree of freedom shell finite element models of an extension twist coupled composite tube were developed and analyzed using MSC/NASTRAN. An analysis employing a simplified beam finite element representation of the specimen with the equivalent engineering stiffness was additionally performed. Results from the shell finite element normal modes and frequency analysis were compared to those obtained experimentally, showing an agreement within 13 percent. There was appreciable degradation in the frequency prediction for the torsional mode, which is elastically coupled. This was due to the absence of off-diagonal coupling terms in the formulation of the equivalent engineering stiffness. Parametric studies of frequency variation due to small changes in ply orientation angle and ply thickness were also performed. Results showed linear frequency variations less than 2 percent per 1 degree variation in the ply orientation angle, and 1 percent per 0.0001 inch variation in the ply thickness.

Lake, Renee C.↗

NASA NTRS1988

A preliminary investigation of finite-element modeling for composite rotor blades

The results from an initial phase of an in-house study aimed at improving the dynamic and aerodynamic characteristics of composite rotor blades through the use of elastic couplings are presented. Large degree of freedom shell finite element models of an extension twist coupled composite tube were developed and analyzed using MSC/NASTRAN. An analysis employing a simplified beam finite element representation of the specimen with the equivalent engineering stiffness was additionally performed. Results from the shell finite element normal modes and frequency analysis were compared to those obtained experimentally, showing an agreement within 13 percent. There was appreciable degradation in the frequency prediction for the torsional mode, which is elastically coupled. This was due to the absence of off-diagonal coupling terms in the formulation of the equivalent engineering stiffness. Parametric studies of frequency variation due to small changes in ply orientation angle and ply thickness were also performed. Results showed linear frequency variations less than 2 percent per 1 degree variation in the ply orientation angle, and 1 percent per 0.0001 inch variation in the ply thickness.

Lake, Renee C.↗

NASA NTRS1983

The GPRIME approach to finite element modeling

GPRIME, an interactive modeling system, runs on the CDC 6000 computers and the DEC VAX 11/780 minicomputer. This system includes three components: (1) GPRIME, a user friendly geometric language and a processor to translate that language into geometric entities, (2) GGEN, an interactive data generator for 2-D models; and (3) SOLIDGEN, a 3-D solid modeling program. Each component has a computer user interface of an extensive command set. All of these programs make use of a comprehensive B-spline mathematics subroutine library, which can be used for a wide variety of interpolation problems and other geometric calculations. Many other user aids, such as automatic saving of the geometric and finite element data bases and hidden line removal, are available. This interactive finite element modeling capability can produce a complete finite element model, producing an output file of grid and element data.

Wallace, D. R.↗

NASA NTRS1993

Solution-adaptive finite element method in computational fracture mechanics

Some recent results obtained using solution-adaptive finite element method in linear elastic two-dimensional fracture mechanics problems are presented. The focus is on the basic issue of adaptive finite element method for validating the applications of new methodology to fracture mechanics problems by computing demonstration problems and comparing the stress intensity factors to analytical results.

Min, J. B.↗

NASA NTRS2013

Band-limited Green's Functions for Quantitative Evaluation of Acoustic Emission Using the Finite Element Method

A method of numerically estimating dynamic Green's functions using the finite element method is proposed. These Green's functions are accurate in a limited frequency range dependent on the mesh size used to generate them. This range can often match or exceed the frequency sensitivity of the traditional acoustic emission sensors. An algorithm is also developed to characterize an acoustic emission source by obtaining information about its strength and temporal dependence. This information can then be used to reproduce the source in a finite element model for further analysis. Numerical examples are presented that demonstrate the ability of the band-limited Green's functions approach to determine the moment tensor coefficients of several reference signals to within seven percent, as well as accurately reproduce the source-time function.

Leser, William P.↗

NASA NTRS1992

A non-linearly stable implicit finite element algorithm for hypersonic aerodynamics

A generalized curvilinear coordinate Taylor weak statement implicit finite element algorithm is developed for the two-dimensional and axisymmetric compressible Navier-Stokes equations for ideal and reacting gases. For accurate hypersonic simulation, air is modeled as a mixture of five perfect gases, i.e., molecular and atomic oxygen and nitrogen as well as nitric oxide. The associated pressure is then determined via Newton solution of the classical chemical equilibrium equation system. The directional semidiscretization is achieved using an optimal metric data Galerkin finite element weak statement, on a developed 'companion conservation law system', permitting classical test and trial space definitions. Utilizing an implicit Runge-Kutta scheme, the terminal algorithm is then nonlinearly stable, and second-order accurate in space and time on arbitrary curvilinear coordinates. Subsequently, a matrix tensor product factorization procedure permits an efficient numerical linear algebra handling for large Courant numbers. For ideal- and real-gas hypersonic flows, the algorithm generates essentially nonoscillatory numerical solutions in the presence of strong detached shocks and boundary layer-inviscid flow interactions.

Iannelli, G. S.↗

NASA NTRS1995

Adaptive Finite Element Methods for Continuum Damage Modeling

The paper presents an application of adaptive finite element methods to the modeling of low-cycle continuum damage and life prediction of high-temperature components. The major objective is to provide automated and accurate modeling of damaged zones through adaptive mesh refinement and adaptive time-stepping methods. The damage modeling methodology is implemented in an usual way by embedding damage evolution in the transient nonlinear solution of elasto-viscoplastic deformation problems. This nonlinear boundary-value problem is discretized by adaptive finite element methods. The automated h-adaptive mesh refinements are driven by error indicators, based on selected principal variables in the problem (stresses, non-elastic strains, damage, etc.). In the time domain, adaptive time-stepping is used, combined with a predictor-corrector time marching algorithm. The time selection is controlled by required time accuracy. In order to take into account strong temperature dependency of material parameters, the nonlinear structural solution a coupled with thermal analyses (one-way coupling). Several test examples illustrate the importance and benefits of adaptive mesh refinements in accurate prediction of damage levels and failure time.

Min, J. B.↗

NASA NTRS1985

Effect of measured material properties on the finite element analysis of an OH-58 composite tail boom

A static and dynamic finite element analysis is conducted on a U.S. Army OH-58 composite tail boom and compared with test data. The tail boom is a filament-wound graphite/epoxy monocoque structure. The structural design of the composite tail boom skin is based on 50-percent graphite fiber volume. However, material tests on representative samples of the tail boom skin reveal that the graphite fiber-volume fraction varied from 44.6 to 49.3 percent. To determine the effect of using measured material properties, static and dynamic finite element analyses are conducted for three fiber-volume conditions of 45, 48, and 50 percent. The static and dynamic model with the 45-percent fiber-volume graphite skins gives the closest agreement with test data.

Bowman, L. M.↗

NASA NTRS1988

A finite-element alternating method for two-dimensional Mode-1 crack configurations

A finite-element alternating method is presented for 2-D Mode-1 crack problems. An analytical solution for an arbitrary polynomial normal pressure distribution applied to the crack faces is obtained and used as the basic solution in the method. The method is applied to several crack problems to study its efficiency and the results are compared to accurate stress-intensity factor solutions in the literature. The method gave reasonably accurate stress-intensity factors and crack opening displacements with minimal computing effort. Because the method must model only the uncracked body, finite-element models with many degrees of freedom are not warranted and therefore, the method has been implemented on personal computers.

Raju, I. S.↗

NASA NTRS1989

A weak Hamiltonian finite element method for optimal guidance of an advanced launch vehicle

A temporal finite-element method based on a mixed form of the Hamiltonian weak principle is presented for optimal control problems. The mixed form of this principle contains both states and costates as primary variables, which are expanded in terms of nodal values and simple shape functions. Time derivatives of the states and costates do not appear in the governing variational equation; the only quantities whose time derivatives appear therein are virtual states and virtual costates. Numerical results are presented for an elementary trajectory optimization problem; they show very good agreement with the exact solution along with excellent computational efficiency and self-starting capability. The feasibility of this approach for real-time guidance applications is evaluated. A simplified model for an advanced launch vehicle application that is suitable for finite-element solution is presented.

Hodges, Dewey H.↗

NASA NTRS1990

Finite element thermo-viscoplastic analysis of aerospace structures

The time-dependent thermo-viscoplastic response of aerospace structures subjected to intense aerothermal loads is predicted using the finite-element method. The finite-element analysis uses the Bodner-Partom unified viscoplastic constitutive relations to determine rate-dependent nonlinear material behavior. The methodology is verified by comparison with experimental data and other numerical results for a uniaxially-loaded bar. The method is then used (1) to predict the structural response of a rectangular plate subjected to line heating along a centerline, and (2) to predict the thermal-structural response of a convectively-cooled engine cowl leading edge subjected to aerodynamic shock-shock interference heating. Compared to linear elastic analysis, the viscoplastic analysis results in lower peak stresses and regions of plastic deformations.

Pandey, Ajay K.↗

NASA NTRS1990

Finite-element thermo-viscoplastic analysis of aerospace structures

The time-dependent thermo-viscoplastic response of aerospace structures subjected to intense aerothermal loads is predicted using the finite-element method. The finite-element analysis uses the Bodner-Partom unified viscoplastic constitutive relations to determine rate-dependent nonlinear material behavior. The methodology is verified by comparison with experimental data and other numerical results for a uniaxially-loaded bar. The method is then used (1) to predict the structural response of a rectangular plate subjected to line heating along a centerline, and (2) to predict the thermal-structural response of a convectively-cooled engine cowl leading edge subjected to aerodynamic shock-shock interference heating. Compared to linear elastic analysis, the viscoplastic analysis results in lower peak stresses and regions of plastic deformations.

Pandey, Ajay↗

NASA NTRS1979

Crash simulation of composite and aluminum helicopter fuselages using a finite-element program

This paper describes a mathematical investigation of the crash-impact responses of an all-composite helicopter cockpit section incorporating an energy absorbing concept and one of conventional aluminum construction, using the Grumman DYCAST finite-element nonlinear structural dynamics computer program. The overall objective of this initial investigation was to explore the application of DYCAST to the design of future helicopter structures. The specific purposes are to assess the value of the finite-element code as a crashworthiness design analysis tool, and to compare the responses of the two fuselage sections. The results indicate that the finite-element simulation is a powerful analysis tool, providing sufficient detail to evaluate individual structural components, and that the crashworthiness of an all-composite cockpit section could be enhanced with energy-absorbing concepts

Winter, R.↗

NASA NTRS1981

Computerized symbolic manipulation in nonlinear finite element analysis

The potential of using computerized symbolic manipulation in the development of nonlinear finite elements is discussed. Three tasks which can be efficiently performed using computerized symbolic manipulation are identified: (1) generation of algebraic expressions for the stiffness coefficients of nonlinear finite elements, (2) generation of FORTRAN source code for numerical evaluation of stiffness coefficients, and (3) checking the correctness of the FORTRAN statements for the arrays of coefficients. The symbolic and algebraic manipulation system MACSYMA is used in the present study. Two sample MACSYMA programs are presented for the development of the nonlinear stiffness coefficients of two-dimensional, shear-flexible, doubly-curved deep shell elements. The first program is for displacement models and the second program is for mixed models with discontinuous stress-resultant fields at interelement boundaries.

Noor, A. K.↗

NASA NTRS1987

Component mode synthesis and large deflection vibration of complex structures. Volume 3: Multiple-mode nonlinear free and forced vibrations of beams using finite element method

Multiple-mode nonlinear forced vibration of a beam was analyzed by the finite element method. Inplane (longitudinal) displacement and inertia (IDI) are considered in the formulation. By combining the finite element method and nonlinear theory, more realistic models of structural response are obtained more easily and faster.

Mei, Chuh↗

NASA NTRS1990

Examples of finite element mesh generation using SDRC IDEAS

IDEAS (Integrated Design Engineering Analysis Software) offers a comprehensive package for mechanical design engineers. Due to its multifaceted capabilities, however, it can be manipulated to serve the needs of electrical engineers, also. IDEAS can be used to perform the following tasks: system modeling, system assembly, kinematics, finite element pre/post processing, finite element solution, system dynamics, drafting, test data analysis, and project relational database.

Zapp, John↗

NASA NTRS1988

Finite elements: Theory and application

Recent advances in FEM techniques and applications are discussed in reviews and reports presented at the ICASE/LaRC workshop held in Hampton, VA in July 1986. Topics addressed include FEM approaches for partial differential equations, mixed FEMs, singular FEMs, FEMs for hyperbolic systems, iterative methods for elliptic finite-element equations on general meshes, mathematical aspects of FEMS for incompressible viscous flows, and gradient weighted moving finite elements in two dimensions. Consideration is given to adaptive flux-corrected FEM transport techniques for CFD, mixed and singular finite elements and the field BEM, p and h-p versions of the FEM, transient analysis methods in computational dynamics, and FEMs for integrated flow/thermal/structural analysis.

Dwoyer, D. L.↗