Search NASA⌕ Search

SEARCH · Search NASA

Results for “Gradient Limiters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Infrared limb scanning in the presence of horizontal temperature gradients - An operational approach

Simulation and analysis of IR limb radiance obtained by a satellite-borne IR limb scanner have demonstrated that horizontal temperature gradients in the atmosphere play an important role in limiting the accuracy of retrieved temperature and constituents below approximately 25 km. A simple operational approach to converting these observed radiances to equivalent spherical radiances is developed which preserves the advantages of the sphericity assumption in the inversion process.

Roewe, D. A.↗

Nonlinear evolution of the lower-hybrid drift instability

The results of simulations of the lower-hybrid drift instability in a neutral sheet configuration are described. The simulations use an implict formulation to relax the usual time step limitations and thus extend previous explicit calculations to weaker gradients, larger mass ratios, and long times compared with the linear growth time. The numerical results give the scaling of the saturation level, heating rates, resistivity, and cross-field diffusion and a demonstration by comparison with a fluid electron model that dissipation in the lower-hybrid drift instability is caused by electron kinetic effects.

Brackbill, J. U.↗

Determination of shuttle orbiter center of gravity from flight measurements

Flight measurements of pitch, yaw, and roll rates and the resultant rotationally induced linear accelerations during three orbital maneuvers on Shuttle mission space transportation system (STS) 61-C were used to calculate the actual orbiter center-of-gravity location. The calculation technique reduces error due to lack of absolute calibration of the accelerometer measurements and compensates for accelerometer temperature bias and for the effects of gravity gradient. Accuracy of the technique was found to be limited by the nonrandom and asymmetrical distribution of orbiter structural vibration at the accelerometer mounting location. Fourier analysis of the vibration was performed to obtain the power spectral density profiles which show magnitudes in excess of 10(exp 4) ug (sup 2)/Hz for the actual vibration and over 500 ug (sup 2)/Hz for the filtered accelerometer measurements. The data from this analysis provide a characterization of the Shuttle acceleration environment which may be useful in future studies related to accelerometer system application and zero-g investigations or processes.

Hinson, E. W.↗

A large-field laser holographic focusing schilieren system

A large-field laser holographic focusing schlieren system for high-speed flow visualization has been built and evaluated. This system is based on a recently improved large-field focusing schlieren technique and is combined with laser holography methods to record three-dimensional flows. A coordinated experimental and computational study of supersonic flows over wedge, cone, and sphere geometries was conducted to evaluate the capabilities and limitations of the system. The ability of the system to focus on planes normal to its optical axis is demonstrated. The sharpness of focus of the present system was found to be limited. Issues regarding obtaining quantitative measurements of the density gradient are discussed.

Doggett, Glen P.↗

Flight research on natural laminar flow applications

Natural laminar flow (NLF) is clearly one of the most potentially attractive drag reduction technologies by virtue of its relative simplicity. NLF is achieved passively, that is, by design of surface shapes to produce favorable pressure gradients. However, it is not without its challenges and limitations. This chapter describes the significant challenges to achieving and maintaining NLF and documents certain of the limitations for practical applications. A brief review of the history and of more recent NLF flight experiments is given, followed by a summary of lessons learned which are pertinent to future applications. The chapter also summarizes important progress in test techniques, particularly in flow visualization and hot-film techniques for boundary-layer measurements in flight.

Holmes, Bruce J.↗

Can Assimilation of Satellite Ozone Data Contribute to the Understanding of the Lower Stratospheric Ozone?

We study the quality of lower stratospheric ozone fields from a three- dimensional global ozone assimilation system. Ozone in this region is important for the forcing of climate, but its global distribution is not fully known because of its large temporal and vertical variability. Modeled fields often have biases due to the inaccurate representation of transport processes in this region with strong gradients. Accurate ozonesonde or satellite occultation measurements have very limited coverage. Nadir measurements, such as those from the Solar Backscatter Ultraviolet/2 (SBUV/2) instrument that provide wide latitudinal coverage, lack the vertical resolution needed to represent sharp vertical features. Limb measurements, such as those from the Michelson Interferometer for Passive Atmospheric Sounding (MIPAS), provide a finer vertical resolution. We show that assimilation of MIPAS data in addition to SBUV/2 data leads to better estimates of ozone in comparison with independent high quality satellite, aircraft, and ozone sonde measurements. Other modifications to the statistical analysis that have an impact on the lower stratospheric ozone will be mentioned: error covariance modeling and data selection. Direct and indirect impacts of transport and chemistry models will be discussed. Implications for multi-year analyses and short-tern prediction will be addressed.

Stajner, I.↗

Physics of Artificial Gravity

This chapter discusses potential technologies for achieving artificial gravity in a space vehicle. We begin with a series of definitions and a general description of the rotational dynamics behind the forces ultimately exerted on the human body during centrifugation, such as gravity level, gravity gradient, and Coriolis force. Human factors considerations and comfort limits associated with a rotating environment are then discussed. Finally, engineering options for designing space vehicles with artificial gravity are presented.

Bukley, Angie↗

Preliminary Results of an Experimental Investigation of the Qu Superconducting Heat Pipe

This note on preliminary results of our evaluation of the so-called Qu Tube is prompted in part by recent concerns expressed to the authors by some researchers regarding the performance characteristics of the superconducting, solid-state heat pipe as described in the patents, or on the company's websites. Briefly, the company's claims include: a new type of heat transfer mechanism that is a form of solid state thermal superconductivity, which results in an effective thermal conductivity of the order of tens of thousands of times that of an equivalent solid silver bar, or, tens to hundreds of times that of liquid - vapor heat pipes. The company's website also refers to tests conducted by Stanford Research Institute that substantiate these claims, but the report is apparently not publicly available. We are conducting an investigation of the Qu Tube under a NASA Grant, and in general find that these claims have merit, but our study is not yet complete. We present some of our preliminary results in part to show that it would not be imprudent to conduct such studies, especially for possible future applications requiring exceptional thermal management performance capabilities. Working with HiTek Services, we originally acquired several Qu Tubes, including 17" long, 5/16" diameter copper tubes, one that is 7 7/8" long, 3/16" diameter, and one that is 4" long, 1" diameter. We subjected the smaller tubes to various exploratory tests, including a transient test with electrical band heaters, boiling water tests, and a series of steady state tests with electrical band heaters heating one end with free convective cooling along the remainder of the length. All results indicate a very high thermal conductivity, but the length of these tubes limited our ability to obtain accurate data on temperature gradients, necessary to determine the effective thermal conductivity. We then acquired nine Qu Tubes that are 10' long, 5/16" diameter, and we have recently conducted initial tests, which further support the claims of exceptional thermal conductivity.

Blackmon, James B.↗

RACORO Continental Boundary Layer Cloud Investigations: 1. Case Study Development and Ensemble Large-Scale Forcings

Observation-based modeling case studies of continental boundary layer clouds have been developed to study cloudy boundary layers, aerosol influences upon them, and their representation in cloud- and global-scale models. Three 60 h case study periods span the temporal evolution of cumulus, stratiform, and drizzling boundary layer cloud systems, representing mixed and transitional states rather than idealized or canonical cases. Based on in situ measurements from the Routine AAF (Atmospheric Radiation Measurement (ARM) Aerial Facility) CLOWD (Clouds with Low Optical Water Depth) Optical Radiative Observations (RACORO) field campaign and remote sensing observations, the cases are designed with a modular configuration to simplify use in large-eddy simulations (LES) and single-column models. Aircraft measurements of aerosol number size distribution are fit to lognormal functions for concise representation in models. Values of the aerosol hygroscopicity parameter, kappa, are derived from observations to be approximately 0.10, which are lower than the 0.3 typical over continents and suggestive of a large aerosol organic fraction. Ensemble large-scale forcing data sets are derived from the ARM variational analysis, European Centre for Medium-Range Weather Forecasts, and a multiscale data assimilation system. The forcings are assessed through comparison of measured bulk atmospheric and cloud properties to those computed in "trial" large-eddy simulations, where more efficient run times are enabled through modest reductions in grid resolution and domain size compared to the full-sized LES grid. Simulations capture many of the general features observed, but the state-of-the-art forcings were limited at representing details of cloud onset, and tight gradients and high-resolution transients of importance. Methods for improving the initial conditions and forcings are discussed. The cases developed are available to the general modeling community for studying continental boundary clouds.

Boundary layers↗

Control Force Compensation in Ground-Based Flight Simulators

This paper presents the results of a study that investigated if controller force compensations accounting for the inertial force and moment due to the aircraft motion during flight have a significant effect on pilot control behavior and performance. Seven rotorcraft pilots performed a side-step and precision hovering task in light turbulence in the Vertical Motion Simulator. The effects of force compensation were examined for two different simulated rotorcraft: linear and UH-60 dynamics with two different force gradient of the lateral stick control. Four motion configurations were used: large motion, hexapod motion, fixed-base motion, and fixed-base motion with compensation. Control-input variables and task performance such as the time to translate to the designated hover position, station-keeping position errors, and handling qualities ratings were used as measures. Control force compensation enabled pilot control behavior and performance more similar to that under high- or medium-fidelity motion to some extent only. Control force compensation did not improve overall task performance considering both rotorcraft models at the same time. The control force compensation had effects on the linear model with lighter force gradient, but only a minimal effect on pilots? control behavior and task performance for the UH-60 model, which had a higher force gradient. This suggests that the control force compensation has limited benefits for controllers that have higher stiffness.

Chung, William W.↗

Control Force Compensation in Ground-Based Flight Simulators

This paper presents the results of a study that investigated if controller force compensations accounting for the inertial force and moment due to the aircraft motion during flight have a significant effect on pilot control behavior and performance. Seven rotorcraft pilots performed a side-step and precision hovering task in light turbulence in the Vertical Motion Simulator. The effects of force compensation were examined for two different simulated rotorcraft: linear and UH-60 dynamics with two different force gradient of the lateral stick control. Four motion configurations were used: large motion, hexapod motion, fixed-base motion, and fixed-base motion with compensation. Control-input variables and task performance such as the time to translate to the designated hover position, station-keeping position errors, and handling qualities ratings were used as measures. Control force compensation enabled pilot control behavior and performance more similar to that under high- or medium-fidelity motion to some extent only. Control force compensation did not improve overall task performance considering both rotorcraft models at the same time. The control force compensation had effects on the linear model with lighter force gradient, but only a minimal effect on pilots? control behavior and task performance for the UH-60 model, which had a higher force gradient. This suggests that the control force compensation has limited benefits for controllers that have higher stiffness.

Chung, William↗

Zemax Modeling of a Self-aligned Focusing Schlieren System with Simulated Compressible Flow

A self-aligned focusing schlieren system is simulated in the ANSYS Zemax OpticStudio software environment. The model uses a custom scatter-defining dynamic link library on the retroreflective background in order to scatter rays in the direction of the incident ray rather than the specular ray. Simulated compressible flow refractive index fields are imported into Zemax by use of the grid gradient object and a workaround to the maximum point limit is introduced. The Ronchi ruling is built as a high resolution bitmap image in MATLAB and set in Zemax as a slide object allowing the bitmap image to either transmit or terminate rays at each line pair. The Zemax simulations are compared to computational numerical schlieren and experimental conventional, path-integrated schlieren results from a hypersonic stagnation point injection flow configuration and an experimental image of a shock wave from a laser-induced breakdown. In the stagnation point injection simulations, the Zemax schlieren images capture complex flow features such as the Mach disk, shear layers, contact surface, and bow shock well, but contains long, curved features (striations) between the model and the bow shock that are not present in the synthetic schlieren image from the CFD or the experimental image. The image from Zemax of the spark-induced shock wave captures the shape and curvature of the shock but appears blurry due to grid discretization in the computational data.

Nicholas A Mejia↗

Tomographic Analysis of SRF Cavities as Asymmetric Plasma Reactors

The tomographic reconstruction of local plasma parameters for nonequilibrium plasma sources is a developing approach, which has a great potential in understanding the fundamental processes and phenomena during plasma processing of SRF cavity walls. Any type of SRF cavity presents a plasma rector with limited or distorted symmetry and possible presence of high gradients. Development of the tomographic method for SRF plasma analysis consists of several steps. First, we define the method based on the inversion of the Abel integral equation for a hollow spherical reactor. Second step is application of the method for the actual elliptical cavity shape. Third step consists of study of the effects of various shapes of the driven electrode. Final step consists of testing the observed line-integrated optical emission data. We will show the typical results in each step and the final result will be presented in the form of correlation between local plasma parameter distributions and local etching characteristics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Alternative Methods for Field Corrections in Helical Solenoids

Helical cooling channels have been proposed for highly efficient 6D muon cooling. Helical solenoids produce solenoidal, helical dipole, and helical gradient field components. Previous studies explored the geometric tunability limits on these main field components. In this paper we present two alternative correction schemes, tilting the solenoids and the addition of helical lines, to reduce the required strength of the anti-solenoid and add an additional tuning knob.

43 PARTICLE ACCELERATORS↗

Fast Aircraft Separation Calculations for Gradient Based Optimization of Airspace Simulations

Simulations of airspace operational concepts can play a significant role in determining future paradigms that would allow for a safe increase in airspace density. In particular, airspace simulations which are capable of handling large numbers of aircraft act as an enabling capability for the testing of proposed airspace operational concepts. Simulations allowing for gradient based optimization methods are particularly attractive, since they would potentially allow for an efficient and empirical means to derive best operational practices. These could also allow for vehicle multidisciplinary design and optimization studies to include air traffic management considerations as a discipline. But any large scale simulation of airspace operations must include some methodology for addressing airspace separation requirements, which in the most direct sense would be tracked in a manner that computationally grows as a quadratic function of the number of simulated aircraft. Efficient indirect methods have been developed in certain contexts to address this limitation. However, any means of addressing separation requirements in a gradient based optimization context should be implemented by functions which provide analytic derivative information to maximize numerical precision and computational efficiency. In this paper, a fast and differentiable separation metric is described in application to gradient based optimization of airspace operations. Rather than computing the separation distance between every pair of aircraft in a simulation, this method effectively reduces the problem to a smaller relevant set using a geometric decomposition. This method guarantees that the smallest distance at all points in simulated time is determined exactly. When used in an optimization constraint context, this guarantees that a minimum separation is maintained between all pairs of aircraft. The presented metric has logarithmic computational growth with respect to the number of simulated aircraft, and is shown to perform well in a series of notional 2D airspace optimization problems when used to enforce specified airborne separation constraints. Results show that this is notably faster than a direct pairwise distance computing metric for optimizations involving both small and large numbers of aircraft, yet enforce separation requirements to the same tolerance. It is shown that this favorable scalability is an enabling capability for more sophisticated air traffic management conceptual studies.

Optimization↗

Numerical Benchmark for High-Reynolds-Number Supercritical Flows with Large Density Gradients

Because of the extreme complexity of physical phenomena at high pressure, only limited data are available for solver validation at device-relevant conditions such as liquid rocket engines, gas turbines, or diesel engines. In the present study, a two-dimensional direct numerical simulation is used to establish a benchmark for supercritical flow at a high Reynolds number and high-density ratio at conditions typically encountered in liquid rocket engines. Emphasis has been placed on maintaining the flow characteristics of actual systems with simple boundary conditions, grid spacing, and geometry. Results from two different state-of-the-art codes, with markedly different numerical formalisms, are compared using this benchmark. The strong similarity between the two numerical predictions lends confidence to the physical accuracy of the results. The established database can be used for solver benchmarking and model development at conditions relevant to many propulsion and power systems.

Engineering↗

Demonstration and Verification of Thermo-Mechanical Bowing in a Limited Free-Bow SFR Concept Using MOOSE

Core bowing due to thermal gradients and irradiation induced swelling and creep introduces significant reactivity feedback effects in liquid metal-cooled fast spectrum reactors. During startup, normal operations, and transient events, differential thermal and flux gradients cause expansion, creep, and swelling, which results in bowing in preferential directions depending on local material properties and load-pad and restraint-ring design. The bowing phenomenon produces negative reactivity during accident conditions provided the restraint system has been properly designed to optimally guide the deformation outwards in the active core region. Under the Department of Energy Nuclear Energy Advanced Modeling and Simulation program, a Multiphysics Object Oriented Simulation Environment (MOOSE)-based multiphysics approach to model core bowing is being developed. The present work expands on previous modeling of simpler International Atomic Energy Agency (IAEA) verification problems with these tools by modeling IAEA Verification Problem 4, which involves a symmetric sector of a reactor core with ducted assemblies undergoing differential thermal expansion due to thermal gradients bowing outward with duct-to-duct contact. This model is available on the National Reactor Innovation Center Virtual Test Bed repository. This example was verified against benchmark participant results, which includes bowing deformation evaluation and duct-to-duct interactions at load pads with mechanical contact.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗

Computational Design of Gradient Paths in Additively Manufactured Functionally Graded Materials

We report additive manufacturing (AM) has enabled the creation of a near infinite set of functionally graded materials (FGMs). One limitation on the manufacturability and usefulness of these materials is the presence of undesirable phases along the gradient path. For example, such phases may increase brittleness, diminish corrosion resistance, or severely compromise the printability of the part altogether. In the current work, a design methodology is proposed to plan an FGM gradient path for any number of elements that avoids undesirable phases at a range of temperatures. Gradient paths can also be optimized for a cost function. A case study is shown to demonstrate the effectiveness of the methodology in the Fe–Ni–Cr system. Paths were successfully planned from 316 L Stainless Steel (316 L SS) to pure Cr that either minimize path length or maximize separation from undesirable phases. Examinations on the stochastic variability, parameter dependency, and computational efficiency of the method are also presented. Finally, several avenues of future research are proposed that could improve the manufacturability, utility, and performance of FGMs through gradient path design.

36 MATERIALS SCIENCE↗