Search NASA⌕ Search

SEARCH · Search NASA

Results for “HUB”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Effect of screen-induced total-pressure distortion on axial-flow compressor stability

An experimental investigation was made to determine the effects of screen-induced total-pressure distortions on two J85-GE-13 turbojet engines. Results were compared to those from a previous program run with a third engine. All compressors were found to be sensitive to a critical angle of circumferential distortion equal to 60 deg., and they all adhered closely to the parallel compressor model. The sensitivity of compressor exit pressure to virtually any type of distortion pattern can be determined by defining stall lines for undistorted, hub radial distorted, and tip radial distorted inflows. The effect of multiple sectors of circumferential distortion is defined.

Calogeras, J. E.↗
NASA NTRS1974

Effect of diffuser bleed on performance of an annular swirl can combustor

A full-scale annular swirl can combustor equipped with diffuser bleed capability was tested at low fuel-air ratio, burning natural gas fuel. Test results show that, by drawing off a small amount of air on the inner or outer diffuser wall, the radial profile of combustor exit temperature could be changed from a strongly tip biased, to a strongly hub biased shape. Furthermore, combustor total pressure loss could be reduced by about one third by using a total bleed rate equal to 6 percent of diffuser inlet flow. At simulated engine idle conditions combustion efficiency was increased from 64 percent to nearly 100 percent by using 3 percent outer wall bleed. Combustor blowout performance was also improved significantly by using this diffuser bleed scheme.

Juhasz, A. J.↗
NASA NTRS1974

An economic assessment of STOL aircraft potential including terminal area environmental considerations, volume 1

The results of an economic and environmental study of short haul airline systems using short takeoff and landing (STOL) aircraft are presented. The STOL system characteristics were optimized for maximum patronage at a specified return on investment, while maintaining noise impact compatibility with the terminal area. Supporting studies of aircraft air pollution and hub airport congestion relief were also performed. The STOL concept specified for this study was an Augmentor Wing turbofan aircraft having a field length capability of 2,000 ft. and an effective perceived noise level of 95 EPNdB at 500 ft. sideline distance. An economic and environmental assessment of the defined STOL system and a summary of the methodology, STOL system characteristics and arena characteristics are provided.

Solomon, H. L.↗
NASA NTRS1974

Supersonic fan blading

Radially extending rotor blades are disposed on a hub to form a supersonic propulsion fan for a turbofan engine. The peripheral spacing of the blades is such as to avoid forming a channel or passageway between adjacent blades. Each has a flat trailing surface extending from the leading edge at least as far to the rear as to cause any pressure waves which might originate on the blade surface to strike the leading surface of the following blade rather than propagate upstream of the blade row. The flat trailing surface of each blade makes an angle with the axis of rotation such that the blade is parallel to a gas inflow into the blades.

Goldstein, A. W.↗
NASA NTRS1974

A theoretical study of the application of jet flap circulation control for reduction of rotor vibratory forces

The results of a study to investigate the theoretical potential of a jet-flap control system for reducing the vertical and horizontal non-cancelling helicopter rotor blade root shears are presented. A computer simulation describing the jet-flap control rotor system was developed to examine the reduction of each harmonic of the transmitted shears as a function of various rotor and jet parameters, rotor operating conditions and rotor configurations. The computer simulation of the air-loads included the influences of nonuniform inflow and blade elastic motions. (no hub motions were allowed.) The rotor trim and total rotor power (including jet compressor power) were also determined. It was found that all harmonics of the transmitted horizontal and vertical shears could be suppressed simultaneously using a single jet control.

Piziali, R. A.↗
NASA NTRS1974

Formulation of a distortion index based on peak compressor pressure ratios

In order to effectively use a compressor face total-pressure distortion index as a measure of inlet-engine compatibility, a correlation of distortion amplitude with stall margin must be developed with minimal scatter. A recent analysis of data recorded in extensive distortion screen tests with the J85-GE-13 turbojet engine has resulted in a correlation based on compressor discharge pressure ratioed to the minimum pressure at the compressor face. Simply by determining compressor stall lines with a single hub radial distortion pattern, a single tip radial pattern, and with undistorted inflow, the overall compressor pressure ratio at stall for even the most complex distortion pattern was found to be predictable.

Calogeras, J. E.↗
NASA NTRS1974

Performance of a short annular dump diffuser using wall trailing-edge suction

A short annular dump (abrupt flow area change) diffuser was tested with suction through wall trailing-edge slots at inlet Mach numbers of 0.19 and 0.27 and at near ambient inlet temperature and pressure, with suction flow varied from zero to 10 percent of the inlet air mass-flow rate. The overall ratio of diffuser exit area to inlet area was 4.0, and the ratio of length to inlet height was 2.0. By applying suction flow separately on either wall or to both walls simultaneously, the original annular jet profile could be altered to either a hub- or tip-biased profile. Diffuser effectiveness was increased from about 25 percent with no suction to 50 percent at 6 percent outer-wall suction and to 52 percent at a combined suction rate on both walls of 10.25 percent. At the same time, diffuser total pressure loss was reduced by one-fourth.

Juhasz, A. J.↗
NASA NTRS1974

Quasi-three-dimensional flow solution by meridional plane analysis

A computer program has been developed to obtain subsonic or shockfree transonic, nonviscous flow analysis on the hub-shroud mid-channel flow surface of a turbomachine. The analysis may be for any annular passage, with or without blades. The blades may be fixed or rotating and may be twisted and leaned. The flow may be axial, radial or mixed. Blade surface velocities over the entire blade are approximated based on the rate of change of angular momentum. This gives a 3-D flow picture based on a 2-D analysis. The paper discusses the method used for the program and shows examples of the type of passages and blade rows which can be analyzed. Also, some numerical examples are given to show how the program can be used for practical assistance in design of blading, annular passages, and annular diffusers.

Katsanis, T.↗
NASA NTRS1974

The effect of cyclic feathering motions on dynamic rotor loads

The dynamic loads of a helicopter rotor in forward flight are influenced significantly by the geometric pitch angles between the structural axes of the hub and blade sections and the plane of rotation. The analytical study presented includes elastic coupling between inplane and out-of-plane deflections as a function of geometric pitch between the plane of rotation and the principal axes of inertia of each blade. The numerical evaluation is based on a transient analysis using lumped masses and elastic substructure techniques. A comparison of cases with and without cyclic feathering motion shows the effect on computed dynamic rotor loads.

Harvey, K. W.↗
NASA NTRS1973

Hingeless rotor vibration and loads at high advance ratio

Experimental values of mean and oscillatory shaft force aeroelastic derivatives with respect to cyclic pitch are presented in dimensionless coefficient form for stiff-bladed hingeless rotors operating at high advance ratio. Good agreement with theory is obtained for the 2P components, in rotating axes, of the oscillatory hub moment derivatives. Trends were predicted for the mean components. Experimental plots of the azimuthal distribution of blade flap bending moment due to cyclic pitch are compared with theoretical for high values of flap frequency ratio and advance ratio. Good agreement is found near the blade root. The similarity parameters that should be preserved in the scale model testing of stiff-bladed hingeless rotors at high advance ratio are reviewed, and some aspects of hingeless rotor wind tunnel testing are considered.

Watts, G. A.↗
NASA NTRS1974

Formulation of a distortion index based on peak compressor pressure ratios

In order to effectively use a compressor face total-pressure distortion index as a measure of inlet-engine compatibility, a correlation of distortion amplitude with stall margin must be developed with minimal scatter. A recent analysis of data recorded in extensive distortion screen tests with the J85-GE-13 turbojet engine has resulted in a correlation based on compressor discharge pressure ratioed to the minimum pressure at the compressor face. Simply by determining compressor stall lines with a single hub radial distortion pattern, a single tip radial pattern, and with undistorted inflow, the overall compressor pressure ratio at stall for even the most complex distortion pattern was found to be predictable.

Calogeras, J. E.↗
NASA NTRS1975

New design of hingeless helicopter rotor improves stability

Cantilever blades are attached directly to rotor hub, thereby substantially reducing cost and complexity and increasing reliability of helicopter rotor. Combination of structural flap-lag coupling and pitch-lag coupling provides damping of 6 to 10%, depending on magnitude of coupling parameters.

Ormiston, R. A.↗
NASA NTRS1974

Two-stage fan. 2: Data and performance with redesigned second stage rotor uniform and distorted inlet flows

A two-stage fan with a first rotor tip speed of 1450 ft/sec (441.96 m/sec) and no inlet guide vanes was tested with uniform and distorted inlet flows, with a redesigned second rotor having a part span shroud to prevent flutter, with variable-stagger stators set in nominal positions, and without rotor casing treatment. The fan achieved a pressure ratio 2.8 at a corrected flow of 185.4 lbm/sec (84.0 kg/sec), an adiabatic efficiency of 85.0 percent, and a stall margin of 12 percent. The redesigned second rotor did not flutter. Tip radial distortion reduced the stall margin at intermediate speed, but had little effect on stall margin at high or low speeds. Hub radial distortion reduced the stall margin at design speed but increased stall margin at low speed. Circumferential distortion reduced stall pressure ratio and flow to give approximately the same stall lines with uniform inlet flow. Distortions were attenuated by the fan. For Vol. 1, see N74-11421.

Messenger, H. E.↗
NASA NTRS1974

Impeller blade design method for centrifugal compressors

The design of a centrifugal impeller with blades that are aerodynamically efficient, easy to manufacture, and mechanically sound is discussed. The blade design method described here satisfies the first two criteria and with a judicious choice of certain variables will also satisfy stress considerations. The blade shape is generated by specifying surface velocity distributions and consists of straight-line elements that connect points at hub and shroud. The method may be used to design radially elemented and backward-swept blades. The background, a brief account of the theory, and a sample design are described.

Jansen, W.↗
NASA NTRS1974

Transonic compressor technology advancements

The highlights of the NASA program on transonic compressors are presented. Effects of blade shape and throat area on losses and flow range are discussed. Some effects of casing treatment on stall margin are presented. Results of tests with varying solidity are also presented. High Mach number, highly loaded stators are discussed and some results of stator hub slit suction are presented.

Benser, W. A.↗
NASA NTRS1974

Theoretical prediction of thick wing and pylon-fuselage-fanpod-nacelle aerodynamic characteristics at subcritical speeds. Part 1: Theory and results

The theoretical development and the comparison of results with data of a thick wing and pylon-fuselage-fanpod-nacelle analysis are presented. The analysis utilizes potential flow theory to compute the surface velocities and pressures, section lift and center of pressure, and the total configuration lift, moment, and vortex drag. The skin friction drag is also estimated in the analysis. The perturbation velocities induced by the wing and pylon, fuselage and fanpod, and nacelle are represented by source and vortex lattices, quadrilateral vortices, and source frustums, respectively. The strengths of these singularities are solved for simultaneously including all interference effects. The wing and pylon planforms, twists, cambers, and thickness distributions, and the fuselage and fanpod geometries can be arbitrary in shape, provided the surface gradients are smooth. The flow through nacelle is assumed to be axisymmetric. An axisymmetric center engine hub can also be included. The pylon and nacelle can be attached to the wing, fuselage, or fanpod.

Tulinius, J. R.↗
NASA NTRS1974

Application of a parameter identification technique to a hingeless helicopter rotor

A mathematical model of a gyro-controlled, three-bladed hingeless helicopter rotor was developed and parameters of the model were estimated using a parameter identification technique. The flapping and feathering degrees of freedom of the blades were modeled. The equations of the model contain time-varying, periodic coefficients due to the forward speed of the rotor. A digital simulation of the analytical model was compared with wind-tunnel measurements to establish the validity of the model. Comparisons of steady-state and transient solutions of the analytical model with the tunnel measurements gave reasonably good matching of gyro angle but less satisfactory matching of hub moment measurements. Further improvements were obtained by use of a parameter identification technique to adjust as many as 10 parameters of the analytical model. The sensitivity of the blade response to small changes in the parameters was also calculated.

Kanning, G.↗
NASA NTRS1975

Spoked wheels to deploy large surfaces in space-weight estimates for solar arrays

Extensible booms were used to deploy and support solar cell arrays of varying areas. Solar cell array systems were built with one or two booms to deploy and tension a blanket with attached cells and bussing. A segmented and hinged rim supported by spokes joined to a common hub is described. This structure can be compactly packaged and deployed.

Crawford, R. F.↗