Search NASA⌕ Search

SEARCH · Search NASA

Results for “InP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Effects of proton irradiation on the performance of InP/GaAs solar cells

InP solar cells are known to be more radiation resistant than either GaAs or Si. In addition, AMO total area efficiencies approaching 19 percent were attained for InP. However, the present high substrate cost presents a barrier to the eventual widespread use of InP cells in space. In addition, if cell thinning becomes desirable, their relative fragility presents a problem. For these reasons, the NASA Lewis Research Center has initiated a program, aimed at producing thin InP cells, by heteroepitaxial deposition of InP on cheaper, more durable substrates. To date, a short term feasibility study as Spire has resulted in cells processed from InP heteroepitaxially deposited on Si substrates with an intervening thin GaAs layer (InP/GaAs/Si) and cells produced from InP deposited on GaAs (InP/GaAs). As a result of this short study efficiencies of over 7 and 9 percent were achieved for InP/GaAs/Si and InP/GaAs respectively. Although these efficiencies are low, they represent a modest and encouraging starting point for a more intensive program. Obviously, when considering economy and mechanical strength, cells processed on silicon substrates are preferred. However, although the InP/GaAs cells are not the final desirable products of this program, their properties serve to highlight several roadblocks to be overcome in producing cells with the more desirable cost and strength properties. Hence, in the present case, the properties of the InP/GaAs cells before and after irradiation by 10 MeV protons are examined. A similar study of InP/GaAs/Si cells will be reported on at a later date.

Weinberg, Irving↗

A biogenic secondary organic aerosol source of cirrus ice nucleating particles

Atmospheric ice nucleating particles (INPs) influence global climate by altering cloud formation, lifetime, and precipitation efficiency. The role of secondary organic aerosol (SOA) material as a source of INPs in the ambient atmosphere has not been well defined. Here, we demonstrate the potential for biogenic SOA to activate as depositional INPs in the upper troposphere by combining field measurements with laboratory experiments. Ambient INPs were measured in a remote mountaintop location at –46°C and an ice supersaturation of 30% with concentrations ranging from 0.1 to 70 L –1 . Concentrations of depositional INPs were positively correlated with the mass fractions and loadings of isoprene-derived secondary organic aerosols. Compositional analysis of ice residuals showed that ambient particles with isoprene-derived SOA material can act as depositional ice nuclei. Laboratory experiments further demonstrated the ability of isoprene-derived SOA to nucleate ice under a range of atmospheric conditions. We further show that ambient concentrations of isoprene-derived SOA can be competitive with other INP sources. This demonstrates that isoprene and potentially other biogenically-derived SOA materials could influence cirrus formation and properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Annual cycle observations of aerosols capable of ice formation in central Arctic clouds

The Arctic is warming faster than anywhere else on Earth, prompting glacial melt, permafrost thaw, and sea ice decline. These severe consequences induce feedbacks that contribute to amplified warming, affecting weather and climate globally. Aerosols and clouds play a critical role in regulating radiation reaching the Arctic surface. However, the magnitude of their effects is not adequately quantified, especially in the central Arctic where they impact the energy balance over the sea ice. Specifically, aerosols called ice nucleating particles (INPs) remain understudied yet are necessary for cloud ice production and subsequent changes in cloud lifetime, radiative effects, and precipitation. Here, we report observations of INPs in the central Arctic over a full year, spanning the entire sea ice growth and decline cycle. Further, these observations are size-resolved, affording valuable information on INP sources. Our results reveal a strong seasonality of INPs, with lower concentrations in the winter and spring controlled by transport from lower latitudes, to enhanced concentrations of INPs during the summer melt, likely from marine biological production in local open waters. This comprehensive characterization of INPs will ultimately help inform cloud parameterizations in models of all scales.

54 ENVIRONMENTAL SCIENCES↗

The contribution of black carbon to global ice nucleating particle concentrations relevant to mixed-phase clouds

Significance The Earth’s climate is affected by the radiative properties of clouds. In clouds containing both supercooled water droplets and ice particles (mixed-phase clouds), cloud lifetime and albedo are affected by the presence of ice nucleating particles (INP). After decades of research, the importance of black carbon (BC) as an INP remains unresolved. In this work, we determined the contribution of BC to INP concentrations ([INP]) from real-world wildfires and prescribed burns. We found that BC does not contribute significantly to [INP] in near-field biomass burning plumes. These results were applied as parameterizations to global climate model output. Combined with previous work on diesel-engine exhaust, we find that BC does not contribute significantly to global [INP] relevant to mixed-phase clouds.

54 ENVIRONMENTAL SCIENCES↗

Effects from Time Dependence of Ice Nucleus Activity for Contrasting Cloud Types

Abstract The role of time-dependent freezing of ice nucleating particles (INPs) is evaluated with the “Aerosol–Cloud” (AC) model in 1) deep convection observed over Oklahoma during the Midlatitude Continental Convective Cloud Experiment (MC3E), 2) orographic clouds observed over North California during the Atmospheric Radiation Measurement (ARM) Cloud Aerosol Precipitation Experiment (ACAPEX), and 3) supercooled, stratiform clouds over the United Kingdom, observed during the Aerosol Properties, Processes And Influences on the Earth’s climate (APPRAISE) campaign. AC uses the dynamical core of the WRF Model and has hybrid bin–bulk microphysics and a 3D mesoscale domain. AC is validated against coincident aircraft, ground-based, and satellite observations for all three cases. Filtered concentrations of ice (>0.1–0.2 mm) agree with those observed at all sampled levels. AC predicts the INP activity of various types of aerosol particles with an empirical parameterization (EP), which follows a singular approach (no time dependence). Here, the EP is modified to represent time-dependent INP activity by a purely empirical approach, using our published laboratory observations of time-dependent INP activity. In all simulated clouds, the inclusion of time dependence increases the predicted INP activity of mineral dust particles by 0.5–1 order of magnitude. However, there is little impact on the cloud glaciation because the total ice is mostly (80%–90%) from secondary ice production (SIP) at levels warmer than about −36°C. The Hallett–Mossop process and fragmentation in ice–ice collisions together initiate about 70% of the total ice, whereas fragmentation during both raindrop freezing and sublimation contributes <10%. Overall, total ice concentrations and SIP are unaffected by time-dependent INP activity. In the simulated APPRAISE case, the main causes of persistence of long-lived clouds and precipitation are predicted to be SIP in weak embedded convection and reactivation following recirculation of dust particles in supercooled layer cloud.

54 ENVIRONMENTAL SCIENCES↗

Final Technical Report for Award SC0008613

Discovering how aerosol particles, present in the atmosphere in sizes of a few nanometers to hundred micrometers, initiate ice crystal formation represents a great challenge. Atmospheric ice nucleation is important because ice crystals alter the radiative properties of clouds and thus climate, and impact precipitation and thus the hydrological cycle. The difficulty in predicting atmospheric ice formation is attributable at least in part, to the diversity of ice nucleation pathways, the physical and chemical complexity of the ice nucleating particles (INPs), and the relatively small numbers of INPs (compared with all other aerosol particles), sometimes less than one in 100000. These factors in turn makes constraining ice nucleation parameterizations for modeling applications challenging. The majority of airborne particles are known to be organic in nature or contain organic biogenic material. The presence of organic material adds to the complexity of the particles and therefore the predictability of ice nucleation events since the organic species can display different phase states, e.g. liquid or solid, in response to temperature and humidity. The award DE-SC0008613 to PI Prof. Daniel Knopf at Stony Brook University, “Relating the Chemical and Physical Properties of Aerosols to the Water Uptake and Ice Nucleation Potential of Particles Collected During the Carbonaceous Aerosols and Radiative Effects Study (CARES)”, allowed examination of laboratory generated aerosol particles and field-collected particles for their propensity to nucleate ice under typical tropospheric conditions and relate ice nucleation to the physicochemical properties of the particles including their morphology and chemical composition. This in turn allowed for development of ice nucleation parameterizations for implementation in cloud models. The award resulted in 10 peer-reviewed publications and more than 20 seminar and conference presentations. We demonstrated that the rate of immersion freezing, when a particle immersed in an aqueous droplet acts as an ice nucleus (IN), can be predicted by knowledge of the IN particle type present and the droplet’s water activity which is equal to ambient relative humidity. Our water activity based immersion freezing model is successful in predicting freezing data including INPs such as mineral dusts, marine biological material, organic species, and surfactant molecules. Its mathematical simplicity makes it an ideal candidate for implementation in cloud and climate models. Furthermore, we could show that this model can reproduce many past laboratory measurements which were generated using a variety of instruments to study immersion freezing. Lastly, we have demonstrated that this model can also be applied to field collected particles. Currently, this novel physical parameterization of immersion freezing is being implemented in a cloud model. We examined the physicochemical properties and the ice nucleation potential of particles collected during CARES applying a novel experimental method that allows identification of the individual INPs within a large population of particles sampled from an ambient environment. Taking advantage of a variety of micro-spectroscopic techniques, we characterized the composition and morphology of IN and non-IN particles present in the airborne population. We developed a new parameterization for quantifying the mixing state of the entire aerosol populations by introducing a mixing state index. We found that the identified INPs belong to the most common particle-type classes observed in the CARES field samples and as such are not special or rare particles. In other words, the INPs can be shown not to be unique in contrast to the common paradigm of being rare and exceptional. Either there are differences between particles acting as IN and particles not acting as IN which are beyond our current detection limit or nucleation occurs randomly on the surface of any one of these compositionally equivalent particles. These results suggest that total particle surface area of the different particle types present in the aerosol population is also a crucial factor when predicting ice nucleation in an air mass. We also observed that ambient organic aerosol particles can initiate ice nucleation and corroborated these findings using laboratory generated organic particles. These experiments demonstrated that information of the organic phase state is important for predicting the ice nucleation pathway and the ability of an organic particle to participate in atmospheric ice crystal formation. This award resulted in substantial new insights in the processes governing immersion freezing, the role of organic aerosol particles in ice cloud formation, and the importance of the ambient aerosol population for prediction of ice nucleation in an air parcel. These findings have significant implications for modeling and field measurement strategies of atmospheric ice nucleation.

54 ENVIRONMENTAL SCIENCES↗

Effects of marine organic aerosols as sources of immersion-mode ice-nucleating particles on high-latitude mixed-phase clouds

Mixed-phase clouds are frequently observed in high-latitude regions and have important impacts on the surface energy budget and regional climate. Marine organic aerosol (MOA), a natural source of aerosol emitted over ~70 % of Earth's surface, may significantly modify the properties and radiative forcing of mixed-phase clouds. However, the relative importance of MOA as a source of ice-nucleating particles (INPs) in comparison to mineral dust, and MOA's effects as cloud condensation nuclei (CCN) and INPs on mixed-phase clouds are still open questions. In this study, we implement MOA as a new aerosol species into the Community Atmosphere Model version 6 (CAM6), the atmosphere component of the Community Earth System Model version 2 (CESM2), and allow the treatment of aerosol–cloud interactions of MOA via droplet activation and ice nucleation. CAM6 reproduces observed seasonal cycles of marine organic matter at Mace Head and Amsterdam Island when the MOA fraction of sea spray aerosol in the model is assumed to depend on sea spray biology but fails when this fraction is assumed to be constant. Model results indicate that marine INPs dominate primary ice nucleation below 400 hPa over the Southern Ocean and Arctic boundary layer, while dust INPs are more abundant elsewhere. By acting as CCN, MOA exerts a shortwave cloud forcing change of -2.78 W m-2 over the Southern Ocean in the austral summer. By acting as INPs, MOA enhances the longwave cloud forcing by 0.35 W m-2 over the Southern Ocean in the austral winter. The annual global mean net cloud forcing changes due to CCN and INPs of MOA are -0.35 and 0.016 W m-2, respectively. These findings highlight the vital importance for Earth system models to consider MOA as an important aerosol species for the interactions of biogeochemistry, hydrological cycle, and climate change.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Physicochemical characterization of free troposphere and marine boundary layer ice-nucleating particles collected by aircraft in the eastern North Atlantic

Abstract. Atmospheric ice nucleation impacts the hydrological cycle and climate by modifying the radiative properties of clouds. To improve our predictive understanding of ice formation, ambient ice-nucleating particles (INPs) need to be collected and characterized. Measurements of INPs at lower latitudes in a remote marine region are scarce. The Aerosol and Cloud Experiments in the Eastern North Atlantic (ACE-ENA) campaign, in the region of the Azores islands, provided the opportunity to collect particles in the marine boundary layer (MBL) and free troposphere (FT) by aircraft during the campaign's summer and winter intensive operation period. The particle population in samples collected was examined by scanning transmission X-ray microscopy with near-edge X-ray absorption fine structure spectroscopy. The identified INPs were analyzed by scanning electron microscopy with energy-dispersive X-ray analysis. We observed differences in the particle population characteristics in terms of particle diversity, mixing state, and organic volume fraction between seasons, mostly due to dry intrusion events during winter, as well as between the sampling locations of the MBL and FT. These differences are also reflected in the temperature and humidity conditions under which water uptake, immersion freezing (IMF), and deposition ice nucleation (DIN) proceed. Identified INPs reflect typical particle types within the particle population on the samples and include sea salt, sea salt with sulfates, and mineral dust, all associated with organic matter, as well as carbonaceous particles. IMF and DIN kinetics are analyzed with respect to heterogeneous ice nucleation rate coefficients, Jhet, and ice nucleation active site density, ns, as a function of the water criterion Δaw. DIN is also analyzed in terms of contact angles following classical nucleation theory. Derived MBL IMF kinetics agree with previous ACE-ENA ground-site INP measurements. FT particle samples show greater ice nucleation propensity compared to MBL particle samples. This study emphasizes that the types of INPs can vary seasonally and with altitude depending on sampling location, thereby showing different ice nucleation propensities, which is crucial information when representing mixed-phase cloud and cirrus cloud microphysics in models.

54 ENVIRONMENTAL SCIENCES↗

MOSAiC-Colorado State University Ice Spectrometer

This data set contains atmospheric ice nucleating particle (INP) measurements, using Colorado State University&rsquo;s (CSU) Ice Spectrometer (IS), of filter collections taken at the U.S. DOE ARM AMF2 site onboard the R/V Polarstern P-deck during the Multidisciplinary Drifting Observatory for the Study of Arctic Climate (MOSAiC) field campaign. Samples were collected from October 27, 2019 to September 24, 2020. A filter sampler was mounted approximately 15 m above ground level on a railing in proximity to (and approximately 3 m below) the Aerosol Observation System (AOS) inlet. Single-use filter units open to the atmosphere were pre-cleaned and pre-loaded with 47-mm diameter Nuclepore polycarbonate (0.2 &micro;m pore-diameter) filters. Filters were typically drawn for a three-day period, with an average volume of air filtered of 87,000 standard liters. Total volumes were calculated through recorded daily flow rates using a mass flow meter (TSI). After collection, filters were stored and transported frozen until analysis using CSU&rsquo;s IS instrument (McCluskey et al., 2018). Aerosol particles were first re-suspended in 8 mL of 0.1 &micro;m-filtered deionized (DI) water. Aliquots of each suspension, and corresponding 11-fold dilutions, were dispensed into polymerase chain reaction (PCR) trays and placed into the aluminum blocks of the IS. Samples were cooled at approximately 0.33 &deg;C min -1 and freezing detected optically with corresponding temperatures recorded. Cumulative INP concentrations were determined through calculating the number of INPs per mL of suspension (Vali, 1971) and converting to concentration per standard L of air by accounting for the proportion of liquid used and volume of air collected. All samples were corrected for the number of INPs on the average of four field blanks (cleaned, handled, transported, and analyzed in the same way without air flow). Two-tailed, 95% confidence intervals for binomial sampling are provided (Agresti and Coull, 1998). Select samples were also heat treated (95 &deg;C for 20 min) to denature and deactivate biological INPs present and digested in 10% H 2 O 2 at 95 &deg;C under UV-B for 20 min to remove any organic carbon INPs. Agresti, A, and BA Coull. 1998. "Approximate is better than &ldquo;exact&rdquo; for interval estimation of binomial proportions." American Statistics 52: 119&ndash;126. https://doi.org/10.2307/2685469 McCluskey, CS, J Ovadnevaite, M Rinaldi, J Atkinson, F Belosi, D Ceburnis, &hellip; and PJ DeMott. 2018. "Marine and Terrestrial Organic Ice-Nucleating Particles in Pristine Marine to Continentally Influenced Northeast Atlantic Air Masses." Journal of Geophysical Research: Atmospheres 123 (11): 6196&ndash;6212, https://doi.org/10.1029/2017JD028033 Vali, G. 1971. "Quantitative Evaluation of Experimental Results and the Heterogeneous Freezing Nucleation of Supercooled Liquids." Journal of the Atmospheric Sciences 28: 402-209. https://doi.org/10.1175/1520-0469(1971)028<0402:QEOERA>2.0.CO;2

54 ENVIRONMENTAL SCIENCES↗

ExINP NSA Ice Nucleating Particle Concentrations

This data set comprises cumulative ambient ice-nucleating particle (INP) concentrations measured at the National Oceanic and Atmospheric Administration's (NOAA’s) Barrow Atmospheric Baseline Observatory (71.3230° N, 156.6114° W, “BRW” hereafter), next to the Atmospheric Radiation Measurement (ARM) North Slope of Alaska (NSA) site and ~ 6 km northeast of the town of Utqiaġvik. Our INP abundance data were generated using a combination of online instrument, the Portable Ice Nucleation Experiment chamber ver. 3 (PINE-03), and an offline cold stage, the West Texas Cryogenic Refrigerator Applied to Freezing Test system (WT-CRAFT). Our online INP data are all from the Examining the Ice-Nucleating Particles from NSA (ExINP-NSA) campaign conducted from October 19, 2021 to May 24, 2024. The offline INP concentration analysis was performed at West Texas A&M University for aerosol particle samples collected on polycarbonate filters (with 0.2-micron diameter pores). The PINE-03 measurements, as well as sampling activities for offline INP measurements, were conducted using the BRW site. An inset laminar sampling stack was mounted to the instrument platform, allowing PINE-03 to intake particle-laden air. For most of the campaign period, the semi-autonomous PINE-03 chamber was remotely controlled from West Texas A&M University using the LabView interface through the BeyondTrust remote-access console. PINE-03 was set to conduct an immersion freezing expansion experiment (i.e., simulated adiabatic cooling along with RHw at or above 100%). Except during the scheduled maintenance periods, the time resolution of each expansion experiment was approximately 12 minutes. PINE-03 continuously measured INP concentrations during the entire campaign without any substantial breaks. For most of the campaign period, PINE scanned its set-point vessel air temperatures from -14 °C to -31 °C and back to -14 °C about every 120 minutes.

54 ENVIRONMENTAL SCIENCES↗

ExINP NSA Ice Nucleating Particle Concentrations

This data set comprises cumulative ambient ice-nucleating particle (INP) concentrations measured at the National Oceanic and Atmospheric Administration's (NOAA’s) Barrow Atmospheric Baseline Observatory (71.3230° N, 156.6114° W, “BRW” hereafter), next to the Atmospheric Radiation Measurement (ARM) North Slope of Alaska (NSA) site and ~ 6 km northeast of the town of Utqiaġvik. Our INP abundance data were generated using a combination of online instrument, the Portable Ice Nucleation Experiment chamber ver. 3 (PINE-03), and an offline cold stage, the West Texas Cryogenic Refrigerator Applied to Freezing Test system (WT-CRAFT). Our online INP data are all from the Examining the Ice-Nucleating Particles from NSA (ExINP-NSA) campaign conducted from October 19, 2021 to May 24, 2024. The offline INP concentration analysis was performed at West Texas A&M University for aerosol particle samples collected on polycarbonate filters (with 0.2-micron diameter pores). The PINE-03 measurements, as well as sampling activities for offline INP measurements, were conducted using the BRW site. An inset laminar sampling stack was mounted to the instrument platform, allowing PINE-03 to intake particle-laden air. For most of the campaign period, the semi-autonomous PINE-03 chamber was remotely controlled from West Texas A&M University using the LabView interface through the BeyondTrust remote-access console. PINE-03 was set to conduct an immersion freezing expansion experiment (i.e., simulated adiabatic cooling along with RHw at or above 100%). Except during the scheduled maintenance periods, the time resolution of each expansion experiment was approximately 12 minutes. PINE-03 continuously measured INP concentrations during the entire campaign without any substantial breaks. For most of the campaign period, PINE scanned its set-point vessel air temperatures from -14 °C to -31 °C and back to -14 °C about every 120 minutes.

54 ENVIRONMENTAL SCIENCES↗

Modelling and design of high performance indium phosphide solar cells

A first principles pn junction device model has predicted new designs for high voltage, high efficiency InP solar cells. Measured InP material properties were applied and device parameters (thicknesses and doping) were adjusted to obtain optimal performance designs. Results indicate that p/n InP designs will provide higher voltages and higher energy conversion efficiencies than n/p structures. Improvements to n/p structures for increased efficiency are predicted. These new designs exploit the high absorption capabilities, relatively long diffusion lengths, and modest surface recombination velocities characteristic of InP. Predictions of performance indicate achievable open-circuit voltage values as high as 943 mV for InP and a practical maximum AM0 efficiency of 22.5 percent at 1 sun and 27 C. The details of the model, the optimal InP structure and the effect of individual parameter variations on device performance are presented.

Rhoads, Sandra L.↗

The Influence of Interstitial Ga and Interfacial Au (sub 2)P (sub 3) on the Electrical and Metallurgical Behavior of Au-Contacted III-V Semiconductors

The introduction of a very small amount of Ga into Au contact metallization on InP is shown to have a significant effect on both the metallurgical and electrical behavior of that contact system. Ga atoms in the interstices of the Au lattice are shown to be effective in preventing the solid state reactions that normally take place between Au and InP during contact sintering. In addition to suppressing the metallurgical interaction, the presence of small amounts of Ga is shown to cause an order of magnitude reduction in the specific contact resistivity. Evidence is presented that the reactions of GaP and GaAs with Au contacts are also drastically affected by the presence of Ga. The sintering behavior of the Au-GaP and the Au-GaAs systems (as contrasted with that of the Au-InP system) is explained as due to the presence of interstitial Ga in the contact metallization. Finally the large, two-to-three order of magnitude drop in the contact resistance that occurs in the Au-InP system upon sintering at 400 degrees Centigrade is shown to be a result of the formation of an Au (sub 2) P (sub 3) layer at the metal-semiconductor interface. Contact resistivities in the 10 (sup -6) ohm square centimeter range are obtained for as-deposited Au on InP when a thin (20 Angstrom) layer of Au (sub 2) P (sub 3) is introduced between the InP and the Au contacts.

Weizer, Victor G.↗

tbsinp (00)

The ice nucleation spectrometer (INS) is an offline analytical measurement system used to process filter samples for freezing temperature spectra of immersion-mode ice-nucleating particle (INP) number concentrations. It is almost identical to the Colorado State University (CSU) ice spectrometer design. The INS-AIR is specific to filter samples collected on aerial platforms, such as the DOE ARM tethered balloon system (TBS) operated by Sandia National Laboratories, using miniaturized aerosol filter samplers. Users are referred to the INS instrument handbook for INS-AIR sampler details. INS-AIR filter samples are collected during intensive operational periods at various ARM sites and then processed on the INS at CSU. This filter log contains the detailed metadata at all ARM sites where INP filter sample collection has occurred or is currently ongoing, including both ground-based routine INP sampling (INS) and TBS INP sampling (INS-AIR). Metadata include start and end times, vacuum line pressures and temperatures, and flow rates; total accumulated flow through each filter; and notes on collection issues or weather conditions. Users can also keep up to date with the status of filter and data processing, even before data are available on ARM’s Data Discovery. Users can contact INP mentors Jessie Creamean or Thomas Hill with any questions.

54 ENVIRONMENTAL SCIENCES↗

The Role of Organic Aerosol in Atmospheric Ice Nucleation: A Review

Predicting the formation of ice crystals in the atmosphere presents one of the great challenges in physical sciences with important implications for the chemistry and composition of the Earth’s atmosphere, the hydrological cycle, and climate. Among atmospheric ice formation processes, heterogeneous ice nucleation proceeds on aerosol particles ranging from a few nanometers to micrometers in size, commonly referred to as ice nucleating particles (INPs). Research over the last two decades has demonstrated that organic matter (OM) is ubiquitous in the atmosphere, present as organic aerosol (OA) particles or as coatings on other particle types. While it is well understood that mineral dust particles can induce ice nucleation under atmospheric conditions, it is currently not clear how much OA particles including pollution aerosol and secondary organic aerosol (SOA) contributes to the ambient INP population. The physicochemical properties of OM make predicting how OM interacts with water vapor leading ultimately to ice crystals challenging. This review focuses on the role of OM in INPs, summarizing and highlighting recent advances in our understanding of the ice nucleation process gained from theoretical, laboratory, and field studies. Examination of ice residuals and INPs with analytical techniques demonstrates that OM participates in atmospheric ice crystal formation. Molecular dynamic simulations provide insight into the microscopic processes that initiate ice nucleation. The amorphous phase state of OM in the supercooled and metastable regime is identified as a key factor in assessing the particles’ nucleation pathways and rates. A theoretical model is advanced, based on particle water activity, to holistically predict amorphous phase changes and ice nucleation rates of particles coated by OM. The goal of this review is to synthesize our current understanding and propose future research directions needed to fully evaluate how OA particles contribute to INPs in the atmosphere.

54 ENVIRONMENTAL SCIENCES↗

Expanding Parameter Space to Enable Low-Temperature Synthesis of Crystalline Indium Phosphide Quantum Dots

Established methods to synthesize indium phosphide quantum dots (QDs) require high temperatures (>180 °C) to make high-quality material for optoelectronic applications. Nonpolar solvent environments are overwhelmingly used in InP QD synthesis to reach the necessary high temperatures and for compatibility with the reactive precursors. In this study, we explored InP QD synthesis in polar aprotic solvent environments to dramatically decrease the temperature required for InP crystallization by imparting ionicity to the precursors and stabilizing charged reaction intermediates. A custom air-free 96- well plate setup was employed to identify key factors impacting low-temperature QD formation, including an increased percentage of polar solvent, carboxylic acid choice, and inclusion of polar additives. Guided by these insights, we developed a synthesis of crystalline, green-emitting InP QDs at 60 °C in a toluene-dimethylformamide mixture. Here's, the QDs withstood established Zn 2+ and HF surface treatments, which increased the photoluminescence quantum yield to 25%. Additionally, we demonstrated the rapid synthesis of quasi-wurtzite InP QDs at room temperature in a polar solvent environment using an acid-free indium myristate precursor.

absorption↗

Radial InP/InAsP/InP heterostructure nanowires on patterned Si substrates using self-catalyzed growth for vertical-type optical devices

Radial InP/InAsP/InP heterostructure nanowires (NWs) on SiO{sub 2}-mask-pattered Si substrates were reported using self-catalyzed InP NWs. Self-catalyzed growth was performed using low growth temperatures and high group-III flow rates, and vertical InP NWs were formed on the mask openings. The diameter and tapering of the self-catalyzed InP NWs were controlled by the introduction of HCl and H{sub 2}S gases during the NW growth, and InP NWs that have a straight region with decreased diameter were formed. Radial InP/InAsP/InP quantum wells (QWs) were grown on the sidewall of the vertical InP NWs on Si substrates. Room-temperature photoluminescence of single NWs from the QW was clearly observed, which exhibited the potential of building blocks for vertical-type optical devices on Si substrates.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of viral infection on the ice nucleation efficiency of marine coccolithophores

A marine coccolithophore (Emiliania huxleyi) and coccolithovirus (EhV-207) were grown together in a marine aerosol reference tank (MART) to investigate how the viral lysis of phytoplankton affects the formation of immersion mode ice nucleating particles (INPs) in sea spray aerosol (SSA). The mean ice nucleation temperatures of SSA produced during viral infection were slightly lower (–28.5 °C) than pre-viral infection (–27.5 °C). Ice nucleation temperatures were relatively low, indicating that organic matter from E. huxleyi is less effective as an INP than phytoplankton examined in previous studies. E. huxleyi is covered in calcium carbonate coccoliths and contains high intracellular concentrations of dimethylsulfoniopropionate (DMSP). The ice nucleation efficiencies of purified components were measured to better understand this model system. Purified coccoliths were moderately effective INPs (–25.3 ± 0.4 °C at 5 x 10 2 mg L -1 (mean ±pooled SD)) that showed a concentration effect, with lower freezing temperatures at lower concentrations. Coccoliths and DMSP were both weakly efficient INPs. In comparison, purified phytoplankton viruses (EhV-207 and CtenRNAV-01) infecting coccolithophores and diatoms, respectively, did not affect freezing at temperatures warmer than the procedural blank. Our results suggest that E. huxleyi, in contrast to diatoms and cyanobacteria, is not a significant source of immersion mode INPs to the marine atmosphere, despite its broad distribution in the global ocean and large-scale bloom formation.

59 BASIC BIOLOGICAL SCIENCES↗