Search NASA⌕ Search

SEARCH · Search NASA

Results for “Integral Effect Test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

In-pixel automatic threshold calibration for the CMS Endcap Timing Layer readout chip

We present the implementation and verification of an in-pixel automatic threshold calibration circuit for the CMS Endcap Timing Layer (ETL) in the High-Luminosity LHC upgrade. The discriminator threshold of the ETL readout chip (ETROC) needs to be calibrated regularly to mitigate the circuit baseline change. Traditional methods need a lot of communication through a slow control system hence are time-consuming. This paper describes an in-pixel automatic scheme with improvements in operating time and usability. In this scheme, a sample-accumulation circuit is used to measure the average discriminator output. A binary successive approximation and linear combination scan are applied to find the equivalent baseline. The actual calibration procedure has been first implemented in FPGA firmware and tested with the ETROC front-end prototype chip (ETROC0). The calibration circuit has been implemented with Triple Modular Redundancy (TMR) and verified with Single Event Effects (SEEs) simulation. A complete calibration process lasts 35 ms with a 40 MHz clock. In the worst case, the dynamic and static power consumption are estimated to be 300 uW and 10.4 uW, respectively. The circuit design, implemented in a 65 CMOS technology, will be integrated into ETROC2, the next iteration of the ETROC with a 16 x16 pixel matrix.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Enhancing Active Distribution Systems Resilience by Fully Distributed Self-Healing Strategy

Distributed restoration can exploit smart grid technologies to enhance the resilience of active distribution networks toward a self-healing smart grid. However, the large number of decision variables, especially the binary ones for reconfiguration, bring challenges to developing scalable distributed distribution service restoration (DDSR) strategies. This paper proposes a fully distributed solution procedure based on the alternating direction method of multipliers (ADMM) for mixed-integer programming problems and applies to develop the DDSR framework. The method consists of relax-drive-polish phases, 1) relaxing binary variables, and applying the convex ADMM as a warm start; 2) driving the solutions toward Boolean values through a proximal operator; 3) fixing the obtained binding binary variables and solving the rest of the problem to polish results and achieve a high-quality suboptimal solution. Then, an autonomous clustering strategy and consensus ADMM are integrated with the proposed method to realize the fully distributed cluster-based framework of DDSR. This framework can first determine DER scheduling and switch status for reconfiguration to energize the out-of-service areas from local faults, and then provide the load restoration solution in a distributed manner for total blackouts in large-scale distribution networks. Furthermore, the effectiveness and scalability of the proposed DDSR framework are demonstrated through testing on the IEEE 123-node, IEEE 8500-node, and synthetic 100k-node test feeders.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Developing IEEE Std 2800-Compliant Algorithms for Transmission-Connected Inverter-Based Resources: Preprint

This study addresses the compliance of Inverter-based Resources (IBRs) with the IEEE Std 2800, a leading standard that defines interconnection and interoperability requirements for IBRs integrated into transmission systems. Focusing on abnormal grid scenarios, the research evaluates the specific demands on IBRs, proposing a comprehensive controller development framework. This framework caters to maintaining ride-trhough operation or implementing strategic disconnections in line with IEEE Std 2800, alongside managing currents during voltage ride-through scenarios. The effectiveness of this proposed controller framework is rigorously validated through case studies, employing a MATLAB/Simulink model of an IBR to test its performance under diverse grid fault conditions, ensuring the IBRs' alignment with standard requirements and their robust performance in enhancing grid reliability.

IEEE Std 2800↗
DOE OSTI2020

Two-temperature warm dense hydrogen as a test of quantum protons driven by orbital-free density functional theory electronic forces

We consider a steady-state (but transient) situation in which a warm dense aggregate is a two-temperature system with equilibrium electrons at temperature Te, ions at Ti, and Te ≠ Ti. Such states are achievable by pump–probe experiments. For warm dense hydrogen in such a two-temperature situation, we investigate nuclear quantum effects (NQEs) on structure and thermodynamic properties, thereby delineating the limitations of ordinary ab initio molecular dynamics. We use path integral molecular dynamics (PIMD) simulations driven by orbital-free density functional theory (OFDFT) calculations with state-of-the-art noninteracting free-energy and exchange-correlation functionals for the explicit temperature dependence. We calibrate the OFDFT calculations against conventional (explicit orbitals) Kohn–Sham DFT. We find that when the ratio of the ionic thermal de Broglie wavelength to the mean interionic distance is larger than about 0.30, the ionic radial distribution function is meaningfully affected by the inclusion of NQEs. Moreover, NQEs induce a substantial increase in both the ionic and electronic pressures. This confirms the importance of NQEs for highly accurate equation-of-state data on highly driven hydrogen. For Te > 20 kK, increasing Te in the warm dense hydrogen has slight effects on the ionic radial distribution function and equation of state in the range of densities considered. In addition, we confirm that compared with thermostatted ring-polymer molecular dynamics, the primitive PIMD algorithm overestimates electronic pressures, a consequence of the overly localized ionic description from the primitive scheme.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

An Integrated Multiscale Experimental-Numerical Analysis on Reconsolidation of Salt-Clay Mixture for Disposal of Heat-Generating Waste (Final NEUP Technical Report)

The overall purpose of this research is to improve understanding of THMC coupling effect on the reconsolidation of granular (or crushed) salt-clay mixture used for seal systems of shafts and drifts in salt repositories. This proposed work is partially motivated by the recent work on the Waste Isolation Pilot Plant (WIPP) that shows the promising sealing capability of clay-salt mixture compared to crushed salt. In particular, primary emphasis is to develop a fully integrated multiscale experiment-numerical study to determine and explain what leads to the superior sealing ability of the clay-salt mixture. These research activities are designed to seek further understanding of (1) why clay additives may enhance the fluid trapping and (2) whether this flow barrier effect may prevail under different combinations of temperature, confining pressure, deviatoric stress and other foreseeable environmental factors. If successful, this enhanced flow trapping ability of the seal provides significant improvement to the seal and repository performance and therefore make the repository safer in the long-term. The experiment component includes microstructural investigation and macroscopic tests on a reconsolidated salt-clay mixture. In the microstructural study, the goal is to (1) characterize microscopic distributions of distinct phases (e.g., clay, salt crystal boundaries, trapped brine, and pore) to examine the connectivity of the pore network inside the salt-clay mixture with different amounts of clay additive and moisture content and (2) analyze multiscale imaging data to reconstruct the polycrystalline microstructures for numerical simulations. Meanwhile, macroscopic tests are performed to analyze how clay alters the failure/creep mechanisms in the salt-clay mixture. Microscopic and macroscopic experimental observations will both be used to calibrate and validate a multiscale model that explicitly simulates the capillary and multiphase flow in the connected pores and the deformation due to the presence of intra-crystalline brine at the pore scale via a new polyhedral discrete element–lattice Boltzmann method (DEM-LBM) coupling model. The pore-scale simulations are homogenized via an upscaling procedure that converts pore-scale information (e.g. force exerted on grain boundary, sliding, pressure-solution) to continuum measures (e.g. Cauchy stress, Darcy’s flow) at each integration point in the macroscopic multiphase TMHC model. This multiscale scheme will allow coupling be- tween high-fidelity simulations of brine-salt-clay interaction and the macroscopic TMHC model. The multiscale model helps the understanding of how the trapped brine inclusion affects the pressure-solution mechanism with the presence of clay and moisture. This work brings new insight into the sealing capacity of salt-clay mixture under elevated temperature over a long period of time - a key to evaluating the potential of salt-clay mixture usage for salt repositories.

42 ENGINEERING↗
DOE OSTI2020

HTR solver: An open-source exascale-oriented task-based multi-GPU high-order code for hypersonic aerothermodynamics

In this study, the open-source Hypersonics Task-based Research (HTR) solver for hypersonic aerothermodynamics is described. The physical formulation of the code includes thermochemical effects induced by high temperatures (vibrational excitation and chemical dissociation). The HTR solver uses high-order TENO-based spatial discretization on structured grids and efficient time integrators for stiff systems, is highly scalable in GPU-based supercomputers as a result of its implementation in the Regent/Legion stack, and is designed for direct numerical simulations of canonical hypersonic flows at high Reynolds numbers. Additionally, the performance of the HTR solver is tested with benchmark cases including inviscid vortex advection, low- and high-speed laminar boundary layers, inviscid one-dimensional compressible flows in shock tubes, supersonic turbulent channel flows, and hypersonic transitional boundary layers of both calorically perfect gases and dissociating air.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Integrated cooling (i-Cool) textile of heat conduction and sweat transportation for personal perspiration management

Perspiration evaporation plays an indispensable role in human body heat dissipation. However, conventional textiles tend to focus on sweat removal and pay little attention to the basic thermoregulation function of sweat, showing limited evaporation ability and cooling efficiency in moderate/profuse perspiration scenarios. Here, we propose an integrated cooling (i-Cool) textile with unique functional structure design for personal perspiration management. By integrating heat conductive pathways and water transport channels decently, i-Cool exhibits enhanced evaporation ability and high sweat evaporative cooling efficiency, not merely liquid sweat wicking function. In the steady-state evaporation test, compared to cotton, up to over 100% reduction in water mass gain ratio, and 3 times higher skin power density increment for every unit of sweat evaporation are demonstrated. Besides, i-Cool shows about 3 °C cooling effect with greatly reduced sweat consumption than cotton in the artificial sweating skin test. The practical application feasibility of i-Cool design principles is well validated based on commercial fabrics. Owing to its exceptional personal perspiration management performance, we expect the i-Cool concept can provide promising design guidelines for next-generation perspiration management textiles.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Developing IEEE Std 2800-Compliant Algorithms for Transmission-Connected Inverter-Based Resources

This study addresses the compliance of Inverter-based Resources (IBRs) with IEEE Standard 2800, a leading standard that defines interconnection and interoperability requirements for IBRs integrated into transmission systems. Focusing on abnormal grid scenarios, the research evaluates the specific demands on IBRs, proposing a controller development framework for abnormal grid conditions. This framework caters to maintaining ride-through operation in line with IEEE Std 2800, alongside managing currents during voltage ride-through scenarios. The effectiveness of this proposed controller frame-work is rigorously validated through case studies, employing a MATLAB/Simulink model of an IBR to test its performance under diverse grid fault conditions, ensuring the IBRs' alignment with standard requirements and their robust performance in enhancing grid reliability.

IEEE Std 2800↗
DOE OSTI2020

Advanced CMOS Reliability Update: Sub 20nm FinFET Assessment

Advances in FinFET design and fabrication enable manufacturing of denser, more compact integrated circuits (ICs) with substantially reduced leakage while shortening the channel-lengths. The same stress-induced leakage and breakdown degradation mechanisms that affect planar transistors also impact FinFET devices. Reliability concerns such as Bias Temperature Instability (BTI), Time Dependent Dielectric Breakdown (TDDB), and Hot Carrier Injection (HCI) become very important with changes to transistor geometry and fin sidewall crystal orientation. Recent testing has shown that FinFETs respond differently to radiation (radiation effects such as total ionizing dose) when compared to planar transistors. These reliability and radiation effects issues become very important when changing transistor geometry and scaling FinFETs towards smaller feature sizes (22-nm, 16-nm, 14- nm, 10-nm, and smaller critical dimensions). The comparable 2019 state of the art transistor densities in current high-volume manufacturing silicon-based foundries is 7-nm (ISMC, Samsung) and 10-nm (Intel) [www.anandtech.com,fuse.wikichip.org]. Released products include supporting components for the cellphone and commercial microprocessor markets respectively. Extensive development in the foundry industry is driving to a 5-nm technology node in late 2020.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Device and material investigations of GaN enhancement-mode transistors for Venus and harsh environments

This Letter reports the device and material investigations of enhancement-mode p-GaN-gate AlGaN/GaN high electron mobility transistors (HEMTs) for Venus exploration and other harsh environment applications. The GaN transistor in this work was subjected to prolonged exposure (11 days) in a simulated Venus environment (460 °C, 94 bar, complete chemical environment including CO2/N2/SO2). The mechanisms affecting the transistor performance and structural integrity in harsh environment were analyzed using a variety of experimental, simulation, and modeling techniques, including in situ electrical measurement (e.g., burn-in) and advanced microscopy (e.g., structural deformation). Through transistor, Transmission Line Method (TLM), and Hall-effect measurements vs temperature, it is revealed that the mobility decrease is the primary cause of reduction of on-state performance of this GaN transistor at high temperature. Material analysis of the device under test (DUT) confirmed the absence of foreign elements from the Venus atmosphere. No inter-diffusion of the elements (including the gate metal) was observed. The insights of this work are broadly applicable to the future design, fabrication, and deployment of robust III-N devices for harsh environment operation.

Physics↗
DOE OSTI2026

A high-efficiency cryogenic neutron spin flipper for IMAGINE-X at the high flux isotope reactor

The Laue neutron macromolecular crystallography beamline, IMAGINE, at the High Flux Isotope Reactor (HFIR) is undergoing a major upgrade to incorporate the dynamic nuclear polarization (DNP) technique. Upon completion, the new IMAGINE-X instrument is expected to enhance the signal-to-noise ratio of the diffraction data by an order of magnitude. To take full advantage of the benefits of DNP, both a highly polarized neutron beam and a high-efficiency neutron spin flipper are required. We have developed a compact cryogenic spin flipper utilizing the Meissner effect in high-Tc yttrium–barium–copper–oxide superconducting films. The flipper has been successfully tested at two HFIR neutron development beamlines, Larmor and Poplar, with neutron wavelengths of 5.3 and 2.4 Å respectively. At Larmor, a flipping efficiency of 0.995 ± 0.004 was achieved for 5.3 Å neutrons, and at Poplar, efficiency of up to 0.9987 ± 0.0004 was obtained for 2.4 Å neutrons. Both tests demonstrated the flipper’s excellent performance and suitability for integration into IMAGINE-X.

Fu, Sichao [Oak Ridge National Laboratory (ORNL), ↗
DOE OSTI2025

Learning PDFs through interpretable latent representations in Mellin space

Representing the parton distribution functions (PDFs) of the proton and other hadrons through flexible, high-fidelity parametrizations has been a long-standing goal of particle physics phenomenology. This is particularly true since the chosen parametrization methodology can play an influential role in the ultimate PDF uncertainties as extracted in QCD global analyses; these, in turn, are often determinative of the reach of experiments at the LHC and other facilities to nonstandard physics, including at large 𝑥, where parametrization effects can be significant. In this study, we explore a series of encoder-decoder machine-learning (ML) models with various neural-network topologies as efficient means of reconstructing PDFs from meaningful information stored in an interpretable latent space. Given recent effort to pioneer synergies between QCD analyses and lattice-gauge calculations, we formulate a latent representation based on the behavior of PDFs in Mellin space, i.e., their integrated moments, and test the ability of various models to decode PDFs from this information faithfully. We introduce a numerical package, PDFdecoder, which implements several encoder-decoder models to reconstruct PDFs with high fidelity and use this end-to-end tool to explore how such neural-network-based models might connect PDF parametrizations to underlying properties like their Mellin moments. We additionally dissect patterns of learned correlations between encoded Mellin moments and reconstructed PDFs that suggest opportunities for further improvements to ML-based approaches to PDF parametrizations and uncertainty quantification.

Machine learning↗
DOE OSTI2024

ORBIT: Oak Ridge Base Foundation Model for Earth System Predictability

Earth system predictability is challenged by the complexity of environmental dynamics and the multitude of variables involved. Current AI foundation models, although advanced by leveraging large and heterogeneous data, are often constrained by their size and data integration, limiting their effectiveness in addressing the full range of Earth system prediction challenges. To overcome these limitations, we introduce the Oak Ridge Base Foundation Model for Earth System Predictability (ORBIT), an advanced vision transformer model that scales up to 113 billion parameters using a novel hybrid tensor-data orthogonal parallelism technique. As the largest model of its kind, ORBIT surpasses the current climate AI foundation model size by a thousandfold. Performance scaling tests conducted on the Frontier supercomputer have demonstrated that ORBIT achieves 684 petaFLOPS to 1.6 exaFLOPS sustained throughput, with scaling efficiency maintained at 41% to 85% across 49,152 AMD GPUs. These breakthroughs establish new advances in AI-driven climate modeling and demonstrate promise to significantly improve the Earth system predictability.

Wang, Xiao↗
DOE OSTI2022

ASC FY2023 Implementation Plan Revision 0

The DOE National Nuclear Security Administration (NNSA) Stockpile Stewardship Program (SSP) is an integrated technical program for maintaining the safety, security, and reliability of the U.S. nuclear stockpile. The SSP incorporates nuclear test data, computational modeling and simulation, and experimental facilities to advance understanding of nuclear weapons. The suite of data analyzed comes from activities including previous nuclear tests, stockpile surveillance, experimental research, and development and engineering programs. This integrated national program requires the continued use of experimental facilities and the computational capabilities to support the SSP missions. These component parts, in addition to an appropriately scaled production capability, enable NNSA to support stockpile requirements. The ultimate goal of the SSP, and thus of the Advanced Simulation and Computing (ASC) Program, is to ensure that the U.S. maintains a safe, secure, and effective strategic deterrent.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Advanced Simulation and Computing: FY25 Implementation Plan

The DOE National Nuclear Security Administration (NNSA) Stockpile Stewardship Program (SSP) is an integrated technical program for maintaining the safety, security, and reliability of the U.S. nuclear stockpile. The SSP incorporates nuclear test data, computational modeling and simulation, and experimental facilities to advance understanding of nuclear weapons. The suite of data analyzed comes from activities including previous nuclear tests, stockpile surveillance, experimental research, and development and engineering programs. This integrated national program requires the continued use of experimental facilities and the computational capabilities to support the SSP missions. These component parts, in addition to an appropriately scaled production capability, enable NNSA to support stockpile requirements. The ultimate goal of the SSP, and thus of the Advanced Simulation and Computing (ASC) program, is to ensure that the U.S. maintains a safe, secure, and effective strategic deterrent.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Van de Graaff Irradiation Studies of Oxygen Sensor and Hydrated Zirconia Sorbent

Commercial-scale production of Mo-99 demands a facility-wide assessment of radiation-induced degradation across process equipment, instrumentation, and purification media. Key factors— total ionizing dose, dose rate, radiolysis-driven chemistry, thermal loads, activation, and any neutron-related effects—should inform material selection, shielding, and component layout. Purification materials (sorbents, resins, filters, seals, housing) require particular attention to ensure that irradiation does not alter selectivity or capacity, generate fines, or introduce leachables that could compromise Mo-99 purity or downstream Tc-99m generator performance. Dose mapping, accelerated irradiation testing, and studies of extractables/leachables together provide the basis for setting maintenance, calibration, and replacement intervals and for qualifying materials that retain mechanical integrity, chemical compatibility, and radiopurity over their service life.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of Neutron Irradiation on the Bond Strength of Steel Embedded in Concrete

The structural integrity of the concrete biological shield (CBS) in light water reactors (LWRs) exposed to long-term radiation raises the question of the effects of fast-neutron and gamma irradiation on the bond properties of embedded carbon-steel reinforcement in concrete, which is critical to the transfer of in-service and accidental loads. The design and execution of a first-of-a-kind irradiation experiment conducted in the LVR-15 test reactor (Czech Republic) are presented along with preliminary post-irradiation examination and testing results. Preliminary analysis shows that the fast neutron flux affects the radiation-induced volumetric of concrete aggregate, that the gamma irradiation induces shrinkage of the chemically bonded water in cementitious hydrates and that the bond strength of steel in concrete at the tested irradiation conditions decreases moderately.

Le Pape, Yann↗
DOE OSTI2023

Integrated Multiscale Model for Design of Robust 3D Solid-state Lithium Batteries

In FY23, we successfully established the multiscale modeling framework for probing the effects of materials microstructure on cell performance of 3D solid-state batteries. The framework covers physicochemical processes co-evolving at the atomistic and microstructure scales. Our simulations revealed the mechanism of initial interfacial degradation, formation of secondary phases, and the structure-property relationship for ion transport and mechanical stability at the interface. In addition, we also established the microstructure-performance relationships by performing sensitivity tests of various microstructure features and extracting their impact on cell performance during charge-discharge cycles. We have successfully applied our multiscale, multiphysics modeling capability to common electrode and electrolyte materials that are of interests to VTO and the experimental teams within the US-Germany collaboration. The insights we obtained from these simulations provide valuable design principles to optimize materials properties for advanced 3D solid-state batteries.

25 ENERGY STORAGE↗