Search NASA⌕ Search

SEARCH · Search NASA

Results for “MAGNETIC COMPRESSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Lunar surface remanent magnetic fields detected by the electron reflection method

We present maps of the lunar surface remanent magnetic fields detected by the electron reflection method. These maps provide substantial coverage of the latitude band from 30 N southward to 30 S with a resolution of about 40 km and a sensitivity of about 0.2 gamma at the lunar surface. Regions of remanent magnetization are observed ranging in size from the resolution limit of 1.25 deg to above approximately 60 deg. The largest contiguous region fills the Big Backside Basin where it is intersected by the spacecraft orbital tracks. Preliminary analyses of the maps show that the source regions of lunar limb compressions correspond to regions of strong surface magnetism, and that there does not appear to be sharply discontinuous magnetization at the edges of maria. We also analyze the electron reflection observations to obtain information on the direction and distribution of magnetization in the Van de Graaff anomaly region.

Lin, R. P.↗
DOE OSTI2020

Spin Transitions and Compressibility of ε-Fe 7 N 3 and γ'-Fe 4 N: Implications for Iron Alloys in Terrestrial Planet Cores

Iron nitrides are possible constituents of the cores of Earth and other terrestrial planets. Pressure-induced magnetic changes in iron nitrides and effects on compressibility remain poorly understood. In this work, we report synchrotron X-ray emission spectroscopy (XES) and X-ray diffraction (XRD) results for ε-Fe 7 N 3 and γ'-Fe 4 N up to 60 GPa at 300 K. The XES spectra reveal completion of high- to low-spin transition in ε-Fe 7 N 3 and γ'-Fe 4 N at 43 and 34 GPa, respectively. The completion of the spin transition induces stiffening in bulk modulus of ε-Fe 7 N 3 by 22% at ~40 GPa, but has no resolvable effect on the compression behavior of γ'-Fe 4 N. Fitting pressure-volume data to the Birch-Murnaghan equation of state yields V 0 = 83.29 ± 0.03 (Å 3 ), K 0 = 232 ± 9 GPa, K 0 ' = 4.1 ± 0.5 for nonmagnetic ε-Fe 7 N 3 above the spin transition completion pressure, and V 0 = 54.82 ± 0.02 (Å 3 ), K 0 = 152 ± 2 GPa, K 0 ' = 4.0 ± 0.1 for γ'-Fe 4 N over the studied pressure range. By reexamining evidence for spin transition and effects on compressibility of other candidate components of terrestrial planet cores, Fe 3 S, Fe 3 P, Fe 7 C 3 , and Fe 3 C based on previous XES and XRD measurements, we located the completion of high- to low-spin transition at ~67, 38, 50, and 30 GPa at 300 K, respectively. The completion of spin transitions of Fe 3 S, Fe 3 P, and Fe 3 C induces elastic stiffening, whereas that of Fe 7 C 3 induces elastic softening. Changes in compressibility at completion of spin transitions in iron-light element alloys may influence the properties of Earth's and planetary cores.

58 GEOSCIENCES↗
DOE OSTI2019

Investigation of Powder Processing, Heat Treating, and Texturing to Improve Gas Atomized alnico Magnets for use in Electric Drive Motors

Alnico permanent magnet materials have been proposed as a rare earth free permanent magnet alternative during an ongoing search to replace rare earth permanent magnets that are used for interior permanent magnet motors, a common motor found in electric vehicles. A powder processing approach was used to study two alnico alloys (Full-Co and lower cost Co-Lean, both with enhanced coercivity) to anticipate high volume manufacturing needed to supply millions of permanent magnets to interior permanent magnet motors. In this study the two alloys were gas atomized, compression molded, and solid-state sintered to fabricate near-final shape alnico magnets. The Full-Co displayed abnormal grain growth (resulting in >1 mm size grains) during sintering while the Co-Lean did not (~20 μm – 400 μm sized grains depending on the sintering hold times). Solid state grain alignment was used to promote a <001> textured (easy axis) microstructure to enhance magnetic properties, yet both alloys did not show predicted grain alignment behavior. Comparisons of the powder processing, microstructures, and magnetic properties of the two alloys will be discussed, as well as an evaluation as to why non-theoretical processing behavior of the Full-Co and Co-Lean alnico permanent magnets is occurring. Preliminary interior permanent magnet motor designs for alnico magnets are discussed, as this is the overarching objective for powder-based alnico permanent magnets.

Rinko, Emily↗
DOE OSTI2024

Spindown of Pulsars Interacting with Companion Winds: The Impact of Magnetospheric Compression

Pulsars in binary systems with strong companion winds can have the magnetopause separating their magnetosphere from the wind located well within their light cylinder. This bow-like enclosure effectively creates a waveguide that confines the pulsar's electromagnetic fields and can significantly alter its spindown. In this paper, we study the spindown of compressed pulsar magnetospheres in such systems. We parameterize the confinement as the ratio between the equatorial position of the magnetopause (or standoff distance) R m and the pulsar's light cylinder R LC . Using particle-in-cell simulations, we quantify the pulsar spindown for a range of compressions, R m /R LC = 1/3–1, and inclination angles, χ = 0°...90°, between magnetic and rotation axes. Our strongly confined models (R m /R LC = 1/3) show two distinct limits. For χ = 0°, the spindown of a compressed pulsar magnetosphere is enhanced by approximately a factor of three compared to an isolated pulsar due to the increased number of open magnetic field lines. Conversely, for χ = 90°, the compressed pulsar spins down at less than 40% of the rate of an isolated reference pulsar due to the mismatch between the pulsar wind stripe wavelength and the waveguide size. We apply our analysis to the 2.77 s oblique rotator (χ = 60°) in the double-pulsar system PSR J0737-3039. With the numerically derived spindown estimate, we constrain its surface magnetic field to B* ≈ (7.3 ± 0.2) × 10 11 G. We discuss the time modulation of its period derivative, the effects of compression on its braking index, and implications for the radio eclipse in PSR J0737-3039.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2018

Ab Initio Study of Electronic and Magnetic Properties of Germanene with Different Nonmagnetic Metal Adatoms

Electronic and magnetic properties of two-dimensional (2D) germanene (Ge) with five different adatoms have been analyzed and discussed by the DFT method. Different nonmagnetic metals adsorbed at different sites, on one hand, a magnetic moment is induced by Mg adatom in the germanene. On the other hand, the adsorptions of Al, Ga, Li, and Na show no magnetism. We further study the effect of strain on the magnetism in Mg-adsorbed germanene; we apply an isotropic tensile and compressive strain on the system. On the basis of our calculations, a tunable magnetism shows as the strain increases. The analysis of the PDOS shows that the s–p hybridization between Mg and Ge atoms results in such magnetic behavior. These magneticadsorbed germanene materials might show potential applications in the nanoscale devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Internal measurements of electromagnetic geodesic acoustic mode (GAM) in EAST plasmas

Velocity, density, and magnetic fluctuations of the geodesic acoustic mode (GAM) have been measured using the Doppler backscattering system, Faraday-effect polarimeter-interferometer, and external pick-up coils in the Experimental Advanced Superconducting Tokamak. Simultaneous measurements of density and velocity fluctuations at the midplane and top of plasmas demonstrate that m = 1 density fluctuations are quantitatively balanced by the compression of perpendicular flow fluctuations. Furthermore, internal magnetic fluctuations associated with GAM have now been directly measured by laser-based Faraday-effect polarimetry for the first time. Line-averaged magnetic fluctuations (up to 16 Gauss, B̃¯R,GAMBT∼0.066%) are significantly larger than those extrapolated from edge coils (a few Gauss) and that magnetic fluctuations increase with β. The observed discrepancy between finite β theory and experimental data indicates the need for further theoretical investigations.

Physics↗
NASA NTRS2005

Antipodal Magnetic Anomalies on the Moon, Contributions from Impact Induced Currents Due to Positive Holes and Flexoelectric Phenomina and Dynamo

Large impacts on the Moon generate large pressure pulses that penetrate the whole body. Several of these large impacts may have generated antipodal structure with anomalous magnetic intensity.These regions can be more than a thousand km across, with fields of the order of tens to hundreds of nT. This is the case of Orientale, Imbrium, Serenitatis, Crisium, and Nectaris impact basins. The production of large-scale magnetic fields and associated crustal magnetization due to lunar basin-forming impacts was hypothesized to have an origin in fields external to the impact plasma cloud that are produced by the magnetohydrodynamic interaction of the cloud with ambient magnetic fields and plasmas. During the period of compressed antipodal field amplification, seismic compressional waves from the impact converge at the antipode resulting in transient shock pressures that reach 2 GPa (20 kbar). This can produce conditions for shock magnetic acquisition of the crust antipodal to impact basins.

Kletetschka, G.↗
DOE OSTI2017

Role of Magnetosonic Solitons in Perpendicular Collisionless Shock Reformation

The nature of the magnetic structure arising from ion specular reflection in shock compression studies is examined by means of 1D particle-in-cell simulations. Propagation speed, field profiles, and supporting currents for this magnetic structure are shown to be consistent with a magnetosonic soliton. Coincidentally, this structure and its evolution are typical of foot structures observed in perpendicular shock reformation. To reconcile these two observations, we propose, for the first time, that shock reformation can be explained as the result of the formation, growth, and subsequent transition to a supercritical shock of a magnetosonic soliton. This argument is further supported by the remarkable agreement found between the period of the soliton evolution cycle and classical reformation results. This new result suggests that the unique properties of solitons can be used to shed new light on the long-standing issue of shock nonstationarity and its role on particle acceleration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Comparative Life Cycle Assessment of Injection Molded and Big Area Additive Manufactured NdFeB Bonded Permanent Magnets

Permanent magnets are expected to play a crucial role in the realization of the clean economy. In particular, the neodymium-iron-boron (Nd2Fe14B or NdFeB) magnets, which have the highest energy density among rare earth permanent magnets, are needed for building more efficient windmill generators, electric vehicle motors, etc. Currently, near-net shape magnets can be either made through sintering and compression molding with extensive post machining or directly through injection molding. However, injection molding has a loading volume fraction limitation of 0.65 for nylon binders. A novel method of manufacturing bonded permanent magnets with loading fraction greater than 0.65 has been demonstrated using Big Area Additive Manufacturing (BAAM) printers. As energy density is directly proportional to the square of the magnet loading fraction, magnets produced using BAAM printers require less volume and magnetic material compared to that of injection molded magnets on average. A comparative LCA shows that this difference in magnetic powder consumption nearly constitutes the difference in the environmental impact categories. Even after assuming recycled magnetic input, the BAAM magnets perform better environmentally than injection molded magnets, especially in the ozone depletion category. Since BAAM printers can accommodate even higher loading fractions, at scale, BAAM printers possibly can bring about a significant decrease in rare earth mineral consumption and environmental emissions. So furthermore, single screw extrusion enables BAAM printers to have high print speeds and allow them to be economically competitive against injection molding. Therefore, BAAM printed magnets show promise in transitioning towards the clean economy.

36 MATERIALS SCIENCE↗
NASA NTRS2013

Energy Release from Impacting Prominence Material Following the 2011 June 7 Eruption

Solar filaments exhibit a range of eruptive-like dynamic activity, ranging from the full or partial eruption of the filament mass and surrounding magnetic structure as a coronal mass ejection to a fully confined or failed eruption. On 2011 June 7, a dramatic partial eruption of a filament was observed by multiple instruments on board the Solar Dynamics Observatory (SDO) and Solar-Terrestrial Relations Observatory. One of the interesting aspects of this event is the response of the solar atmosphere as non-escaping material falls inward under the influence of gravity. The impact sites show clear evidence of brightening in the observed extreme ultraviolet wavelengths due to energy release. Two plausible physical mechanisms for explaining the brightening are considered: heating of the plasma due to the kinetic energy of impacting material compressing the plasma, or reconnection between the magnetic field of low-lying loops and the field carried by the impacting material. By analyzing the emission of the brightenings in several SDO/Atmospheric Imaging Assembly wavelengths, and comparing the kinetic energy of the impacting material (7.6 × 10(exp 26) - 5.8 × 10(exp 27) erg) to the radiative energy (approx. 1.9 × 10(exp 25) - 2.5 × 10(exp 26) erg), we find the dominant mechanism of energy release involved in the observed brightening is plasma compression.

Sun: corona↗
DOE OSTI2021

Fermi-type particle acceleration from magnetic reconnection at the termination shock of a relativistic striped wind

An oblique-rotating pulsar generates a relativistic striped wind in a pulsar wind nebula (PWN). The termination shock of the PWN compresses the Poynting-flux-dominated flow and drives magnetic reconnection. By carrying out particle-in-cell simulations of the termination shock of the PWN, we study the shock structure as well as the energy conversion processes and particle acceleration mechanisms. With the recent advances in the numerical methods, we extend the simulations to the ultrarelativistic regime with a bulk Lorentz factor of up to γ 0 = 10 6 . Magnetic reconnection at the termination shock is highly efficient at converting magnetic energy to particle kinetic energy and accelerating particles to high energies. Similar to earlier studies, we find that the resulting energy spectra crucially depend on λ/d e (λ is the wavelength of the striped wind and de is the relativistic plasma skin depth). When λ/d e is large (λ ≳ 40d e ), the downstream particle spectra form a power-law distribution in the magnetically dominated relativistic wind regime. By analyzing particle trajectories and statistical quantities relevant to particle energization, we find that Fermi-type mechanism dominates the particle acceleration and power-law formation. We find that the results for particle acceleration are scalable as γ 0 and σ 0 increase to large values. The maximum energy for electrons and positrons can reach hundreds of TeV if the wind has a bulk Lorentz factor of γ0 ≈ 106 and a magnetization parameter of σ 0 = 10, which can explain the recent observations of high-energy gamma rays from PWNe

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2017

Evolutionary Description of Giant Molecular Cloud Mass Functions on Galactic Disks

Recent radio observations show that giant molecular cloud (GMC) mass functions noticeably vary across galactic disks. High-resolution magnetohydrodynamics simulations show that multiple episodes of compression are required for creating a molecular cloud in the magnetized interstellar medium. In this article, we formulate the evolution equation for the GMC mass function to reproduce the observed profiles, for which multiple compressions are driven by a network of expanding shells due to H ii regions and supernova remnants. We introduce the cloud–cloud collision (CCC) terms in the evolution equation in contrast to previous work (Inutsuka et al.). The computed time evolution suggests that the GMC mass function slope is governed by the ratio of GMC formation timescale to its dispersal timescale, and that the CCC effect is limited only in the massive end of the mass function. In addition, we identify a gas resurrection channel that allows the gas dispersed by massive stars to regenerate GMC populations or to accrete onto pre-existing GMCs. Our results show that almost all of the dispersed gas contributes to the mass growth of pre-existing GMCs in arm regions whereas less than 60% contributes in inter-arm regions. Our results also predict that GMC mass functions have a single power-law exponent in the mass range <10{sup 5.5} M{sub ⊙} (where M{sub ⊙} represents the solar mass), which is well characterized by GMC self-growth and dispersal timescales. Measurement of the GMC mass function slope provides a powerful method to constrain those GMC timescales and the gas resurrecting factor in various environments across galactic disks.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2017

Modeling the Plasma Flow in the Inner Heliosheath with a Spatially Varying Compression Ratio

We examine a semi-analytical non-magnetic model of the termination shock location previously developed by Exarhos and Moussas. In their study, the plasma flow beyond the shock is considered incompressible and irrotational, thus the flow potential is analytically derived from the Laplace equation. Here we examine the characteristics of the downstream flow in the heliosheath in order to resolve several inconsistencies existing in the Exarhos and Moussas model. In particular, the model is modified in order to be consistent with the Rankine–Hugoniot jump conditions and the geometry of the termination shock. It is shown that a shock compression ratio varying along the latitude can lead to physically correct results. We describe the new model and present several simplified examples for a nearly spherical, strong termination shock. Under those simplifications, the upstream plasma is nearly adiabatic for large (∼100 AU) heliosheath thickness.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2018

Bunch Compression of Flat Beams

Flat beams can be produced via a linear manipulation of canonical-angular-momentum (CAM) dominated beams using a set of skew-quadrupole magnets. Recently, such beams were produced at Fermilab Accelerator Science and Technology (FAST) facility 1. In this paper we report the results of flat beam compression study in a magnetic chicane at an energy E ~ 32 MeV. Additionally, we investigate the effect of energy chirp in the round-to-flat beam transform. The experimental results are compared with numerical simulations.

43 PARTICLE ACCELERATORS↗
DOE OSTI2017

Thermal and magnetic hysteresis associated with martensitic and magnetic phase transformations in Ni 52 Mn 25 In 16 Co 7 Heusler alloy

Ni-Mn-In-Co Heusler alloys demonstrate promising magnetocaloric performance for use as refrigerants in magnetic cooling systems with the goal of replacing the lower efficiency, eco-adverse fluid-compression technology. The largest change in entropy occurs when the applied magnetic field causes a merged structural and magnetic transformation and the associated entropy changes of the two transformations works constructively. In this study, magnetic and crystalline phase transformations were each treated separately and the effects of the application of magnetic field on thermal hystereses associated with both structural and magnetic transformations of the Ni 52 Mn 25 In 16 Co 7 were studied. From the analysis of synchrotron diffraction data and thermomagnetic measurements, it was revealed that the alloy undergoes both structural (from cubic austenite to a mixture of 7M & 5M modulated martensite) and magnetic (ferromagnetic to a low-magnetization phase) phase transformations. Here, thermal hysteresis is associated with both transformations, and the variation of the thermal hystereses of the magnetic and structural transformations with applied magnetic field is significantly different. Because of the differences between the hystereses loops of the two transformations, they merge only upon heating under a certain magnetic field.

36 MATERIALS SCIENCE↗
DOE OSTI2016

CHANGE OF MAGNETIC FIELD-GAS ALIGNMENT AT THE GRAVITY-DRIVEN ALFVÉNIC TRANSITION IN MOLECULAR CLOUDS: IMPLICATIONS FOR DUST POLARIZATION OBSERVATIONS

Diffuse striations in molecular clouds are preferentially aligned with local magnetic fields, whereas dense filaments tend to be perpendicular to them. When and why this transition occurs remain uncertain. To explore the physics behind this transition, we compute the histogram of relative orientation (HRO) between the density gradient and the magnetic field in three-dimensional magnetohydrodynamic (MHD) simulations of prestellar core formation in shock-compressed regions within giant molecular clouds. We find that, in the magnetically dominated (sub-Alfvénic) post-shock region, the gas structure is preferentially aligned with the local magnetic field. For overdense sub-regions with super-Alfvénic gas, their elongation becomes preferentially perpendicular to the local magnetic field. The transition occurs when self-gravitating gas gains enough kinetic energy from the gravitational acceleration to overcome the magnetic support against the cross-field contraction, which results in a power-law increase of the field strength with density. Similar results can be drawn from HROs in projected two-dimensional maps with integrated column densities and synthetic polarized dust emission. We quantitatively analyze our simulated polarization properties, and interpret the reduced polarization fraction at high column densities as the result of increased distortion of magnetic field directions in trans- or super-Alfvénic gas. Furthermore, we introduce measures of the inclination and tangledness of the magnetic field along the line of sight as the controlling factors of the polarization fraction. Observations of the polarization fraction and angle dispersion can therefore be utilized in studying local magnetic field morphology in star-forming regions.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS2011

Fusion Propulsion Z-Pinch Engine Concept

Fusion-based nuclear propulsion has the potential to enable fast interplanetary transportation. Due to the great distances between the planets of our solar system and the harmful radiation environment of interplanetary space, high specific impulse (Isp) propulsion in vehicles with high payload mass fractions must be developed to provide practical and safe vehicles for human spaceflight missions. The Z-Pinch dense plasma focus method is a Magneto-Inertial Fusion (MIF) approach that may potentially lead to a small, low cost fusion reactor/engine assembly1. Recent advancements in experimental and theoretical understanding of this concept suggest favorable scaling of fusion power output yield 2. The magnetic field resulting from the large current compresses the plasma to fusion conditions, and this process can be pulsed over short timescales (10(exp -6 sec). This type of plasma formation is widely used in the field of Nuclear Weapons Effects testing in the defense industry, as well as in fusion energy research. A Decade Module 2 (DM2), approx.500 KJ pulsed-power is coming to the RSA Aerophysics Lab managed by UAHuntsville in January, 2012. A Z-Pinch propulsion concept was designed for a vehicle based on a previous fusion vehicle study called "Human Outer Planet Exploration" (HOPE), which used Magnetized Target Fusion (MTF) 3 propulsion. The reference mission is the transport of crew and cargo to Mars and back, with a reusable vehicle.

Miernik, J.↗