Search NASA⌕ Search

SEARCH · Search NASA

Results for “MAGNETIC PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Crystal structure, magnetic properties and bonding analysis of M 3 Pt 23 Ge 11 (M=Ca, Sr, Ba and Eu)

The properties of Pt-based materials can be intriguing due to the importance of spin-orbit coupling for Pt. Herein, we report four new phases with formulas M 3 Pt 23 Ge 11 (M ​= ​Ca, Sr, Ba and Eu), which adopt the same structure type as Ce3Pt23Si11. Magnetic susceptibility measurements indicate that none of the phases is superconducting above 1.8 ​K, while for Eu 3 Pt 23 Ge 11 ferromagnetic ordering is observed at ~ 3 ​K. The low Curie temperature for that material compared to that of Eu 3 Pt 23 Si 11 may be due to its larger Eu–Eu distance. One potential factor that destabilizes the structure of other rare-earth based M 3 Pt 23 Ge 11 is demonstrated through COHP calculations.

36 MATERIALS SCIENCE↗
NASA NTRS1990

Magnetic properties of the 110K superconducting phase in Pb-doped Bi-Sr-Ca-Cu-O thin films

The relaxation of the remnant moment induced in a nearly single phase high T(sub c) thin film of Pd-doped Bi-Sr-Ca-Cu-O was investigated. Measurements reveal that the relaxation obeys a logarithmic time dependence for observation times up to 2000 seconds. The temperature dependence of the initial magnetization of the film and its decay rate are obtained. The initial magnetization monotonically decreases. However, the decay rate normalized by initial magnetization has a peak at approximately 14 K for an applied field of 500 gauss. The peak shifts to lower temperature for a stronger magnetic field. These data are compared with existing data on other high T(sub c) superconducting materials.

Tanaka, Atsushi↗
NASA NTRS1990

Elemental fractionation and magnetic properties of melt-based Y1Ba2Cu3Oz containing excess Tb or Pt

Scanning electron microscopy of certain partially melted Y-Ba-Cu-O materials containing minority metal oxide species (Y:Tb:Ba:Cu = 1:0.1:2:3 or Y:Ba:Cu with Pt impurities), accompanied by both EDX and EMP analysis, indicates that the minority species (Tb or Pt) is quantitatively concentrated in a relatively small number of 123-type grains. High magnetic susceptibility and magnetization observed for these materials indicate that such elemental distribution is not detrimental to superconducting behavior.

Hojaji, Hamid↗
DOE OSTI2023

Static and dynamical magnetic properties of the extended Kitaev-Heisenberg model with spin vacancies

Motivated by the potential to suppress antiferromagnetic long-range order in favor of the long-sought-after Kitaev quantum spin liquid state, we study the effect of spin vacancies in the extended Kitaev-Heisenberg model. In particular, we focus on a realistic model obtained from fitting inelastic neutron scattering on α–RuCl 3 . We observe that the long-range zigzag magnetic ordered state only survives when the doping concentration is smaller than 5%. Upon further increasing the spin vacancy concentration, the ground state becomes a short-range ordered state at low temperatures. Compared with experiments, our classical solution overstabilizes the zigzag correlation in the presence of spin vacancies. Here, our theoretical results provide guidance toward interpreting inelastic neutron scattering experiments on magnetically diluted Kitaev candidate materials

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1980

SPAR and ASTP studies of plane-front solidification and magnetic properties of Bi/MnBi

Eutectic and off-eutectic Bi/MnBi compositions have been directionally solidified parallel, anti-parallel and perpendicular to the gravity vector in a one-g environment and in low-gravity during the ASTP flight. MnBi rod diameter and interparticle spacing distributions are similar for all gravity vector orientations when grown at high solidification rates in one-g. Previously reported ASTP results are explained by the existence of a metastable magnetic phase and off-eutectic solidification models.

Pirich, R. G.↗
DOE OSTI2018

Effect of Blocking and Superconducting Layer Doping on the Superconductivity and Magnetic Properties of Polycrystalline Sr{sub 2}CaCu{sub 2}O{sub 6}

The possible difference in the properties upon doping the Sr{sub 2}CaCu{sub 2}O{sub 6} superconducting or blocking layers with Fe and Eu respectively was investigated in this work. The homogeneous Sr{sub 2−y}Eu{sub y}CaCu{sub 2}O{sub 6+δ} and Sr{sub 2}CaCu{sub 2−x}Fe{sub x}O{sub 6+δ} (y = 0, 0.1, 0.5, x = 0, 0.05) compounds were produced by a high-pressure synthesis route. Judging by the magnetic susceptibility measurements, all samples exhibit a superconductivity transition and the Eu/Fe concentration dependencies on the diamagnetic moment and average T{sub c} have been constructed using the experimental data. As a result, an unusual behavior of the T{sub c} value was observed for the samples with doped Eu: a fivefold reduction in the europium concentration in the sample does not give a noticeable effect on the transition temperature value while the diamagnetic signal becomes more stronger. Complex superconducting dome was found for Eu-doped material: 0.1 ≤ y ≤ 0.5 region T{sub c} vs. concentration data were approximated by inverted parabola-like curve with a maximum at y = 0.3. Difference in properties of the Eu and Fe-doped samples was also found in the behavior of the hysteresis loops showed the opposite orientations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Synthesis and magnetic properties of LaFe 13- x - y M x Si y N 3 nitrides

Here, single-phase LaFe 13-x-y M x Si y N 3 compounds (M = Mn) were synthesized by subjecting intermetallic precursors to the ammonia flow at 623 K for 4 h. The nitrides derived from Si-poor (y ≤ 3) cubic intermetallics retain the NaZn 13 -type crystal structure and show considerable (~3 %) lattice expansion compared to the nitrogen-free materials. The temperatures of the magnetic ordering transitions, all of which are second order, increase by ~ 200 K as a result of nitrogenation, and all nitrides exhibit rather weak and broad magnetocaloric effects. The nitrides are stable below 750 K, but they begin to lose nitrogen above this temperature, fully decomposing above 1050 K. The nitrogenation of the tetragonal LaFe 9 Si 4 results in the decomposition of the intermetallic phase and formation of the Fe 3 N compound together with unidentified amorphous phase(s).

36 MATERIALS SCIENCE↗
DOE OSTI2024

Advancing Heteroanionicity in Zintl Phases: Crystal Structures, Thermoelectric and Magnetic Properties of Two Quaternary Semiconducting Arsenide Oxides, Eu 8 Zn 2 As 6 O and Eu 14 Zn 5 As 12 O

Two novel quaternary oxyarsenides, Eu 8 Zn 2 As 6 O and Eu 14 Zn 5 As 12 O, were synthesized through metal flux reactions, and their crystal structures were established by single-crystal X-ray diffraction methods. Eu 8 Zn 2 As 6 O crystallizes in the orthorhombic space group Pbca, featuring polyanionic ribbons composed of corner-shared triangular [ZnAs 3 ] units, running along the [100] direction. The structure of Eu 14 Zn 5 As 12 O crystallizes in the monoclinic space group P2/m and its anionic substructure can be described as an infinite “ribbonlike” chain comprised of [ZnAs 3 ] trigonal-planar units, although the structural complexity here is greater and also amplified by disorder on multiple crystallographic positions. In both structures, the O 2– anion occupies an octahedral void with six neighboring Eu 2+ cations. Formal electron counting, electronic structure calculations, and transport properties reveal the charge-balanced semiconducting nature of these heteroanionic Zintl phases. High-temperature thermoelectric transport properties measurements on Eu 14 Zn 5 As 12 O reveal relatively high resistivity (ρ 500K = 8 Ω·cm) and Seebeck coefficient values (S 500K = 220 μV K –1 ), along with a low concentration and mobility of holes as the dominant charge-carriers (n 500K = 8.0 × 10 17 cm –3 , μ 500K = 6.4 cm 2 /V s). Magnetic studies indicate the presence of divalent Eu 2+ species in Eu 14 Zn 5 As 12 O and complex magnetic ordering, with two transitions observed at T 1 = 21.6 K and T 2 = 9 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1984

Effects of thermal cycling on magnetic properties of lunar analogs

An experimental study has been performed to determine whether stresses associated with thermal cycling cracks can affect the coercivity of remanence carried by iron in lunar samples. Initially, samples were cycled up to 100 times in a refrigerator over a period of about 30 min per cycle. In a second set of experiments, samples were dipped directly into liquid nitrogen up to 100 times at about 1 min per cycle. Comparison of AF demagnetization curves of weak field anhysteretic remanent magnetization before and after cycling revealed no systematic differences. Calculations based on a model of spherical iron grains within olivine or troilite indicate that it is unlikely that the iron will crack under thermal stress. Thus, thermal cycling does not appear to provide an explanation for increasing the stability of remanence in samples from the lunar surface.

Barron, A. M.↗
NASA NTRS1990

Iron mineralogy of a Hawaiian palagonitic soil with Mars-like spectral and magnetic properties

Visible and near-IR spectral data for some palagonitic soils from Mauna Kea, Hawaii, are similar to corresponding spectral data for Mars. It is important to understand the composition, distribution, and mineralogy of the ferric-bearing phases for the best spectral analogues because the correspondence in spectral properties implies that the nature of their ferric-bearing phases may be similar to those on Mars. In order to constrain interpretations of the Martian data, a variety of palagonitic soils should be studied in order to establish to what extent differences in their spectral data correspond to differences in the mineralogy of their ferric-bearing phases. Spectral (350-2100 nm), Mossbauer, magnetic, and some compositional data for one of a suite of Hawaiian palagonitic soils are presented. The soil (HWMK1) was collected below the biologically active zone from the sides of a gully cut at 9000 ft elevation on Mauna Kea. The soil was wet sieved with freon into seven size fractions less than 1 mm.

Morris, Richard V.↗
NASA NTRS1998

Effects of Heat Treatment on the Magnetic Properties of Polymer-Bound Iron Particle Cores

Spherical iron particles of three different size distributions, 6-10 microns in diameter, 100 mesh and 30-80 mesh, were mixed with 2.0 wt. % of soluble imide and compression molded at 300 C under 131 MPa. Post fabrication heat treatments were performed at 960 C for 6 hours resulting in a significant enhancement of the permeability in low field region for all the specimens except for the one made of 30-80 mesh particles. The rate of core loss of these specimens at a magnetic induction of 5 kG measured up to 1 kHz shows a noticeable increase after heat treatment which, along with the permeability enhancement, can be explained by the coalescence of particles forming a network of conductivity paths in the specimens. The scanning electron micrographs taken for the 6-10 micron particle specimens show no evidence of heat treatment-induced grain growth. The untreated specimens show a very weak f(sup 2) dependence of the core loss which clearly indicates a negligible contribution from the eddy current loss. In particular, an almost perfect linearity was found in the frequency dependence of the core loss of the untreated specimen made of 100 mesh iron particles.

Namkung, M.↗
DOE OSTI2021

Role of Chiral Two-Body Currents in 6 Li Magnetic Properties in Light of a New Precision Measurement with the Relative Self-Absorption Technique

A direct measurement of the decay width of the excited $0^+_1$ state of 6 Li using the relative self-absorption technique is reported. Our value of $Γ_{γ,0^{+}_{1}} → 1^{+}_{1}$ = 8.17 (14) stat. (11) syst. eV provides sufficiently low experimental uncertainties to test modern theories of nuclear forces. The corresponding transition rate is compared to the results of ab initio calculations based on chiral effective field theory that take into account contributions to the magnetic dipole operator beyond leading order. This allows for a precision test of the impact of two-body currents that enter at next-to-leading order.

36 MATERIALS SCIENCE↗
NASA NTRS1998

Effects of Heat Treatment on the Magnetic Properties of Polymer-Bound Iron Particle Cores

Spherical iron particles of three different size distributions, 6-10 micrometers in diameter, 100 mesh and 30-80 mesh, were mixed with 2.0 wt % of soluble imide and compression molded at 300 C under 131 MPa. Post-fabrication heat treatments were performed at 960 C for 6 h resulting in a significant enhancement of the permeability in low field region for all the specimens except for the one made of 30-80 mesh particles. The rate of core loss of these specimens at a magnetic induction of 5 kG measured up to 1 kHz shows a noticeable. increase after heat treatment which, along with the permeability enhancement, can be explained by the coalescence of particles forming a network of conductivity paths in the specimens. ne scanning electron micrographs taken for the 6-10 micrometer particle specimens show no evidence of heat treatment-induced grain growth. The untreated specimens show a very weak f(sup 2) -dependence of the core loss which clearly indicates a negligible contribution from the eddy current loss. In particular, an almost perfect linearity was found in the frequency dependence of the core loss of the untreated specimen made of 100 mesh iron particles.

Namkung, M.↗
DOE OSTI2022

Impact of cobalt doping on structural and magnetic properties of zinc oxide nanocomposites synthesized by mechanical ball-milling method

A series of zinc oxide (ZnO) semiconductor nanocomposite samples doped with different concentrations of cobalt (Co) were successfully synthesized via simple and highly effective mechanical ball-milling method using suitable precursors. All doped nanocomposites crystallized in hexagonal wurtzite formation of ZnO. No alteration in the wurtzite structure, with no evidence of any segregated secondary phase(s) was detected with increasing doping concentrations. This result unambiguously verified the substitution of Zn 2+ sites by Co 2+ ions in the ZnO host lattice for different doping concentrations. Moreover, room temperature ferromagnetic behavior was observed in all doped nanocomposite samples in the reported work. Present study clearly shows that mechanical ball-milling is a facile, inexpensive, eco-friendly method to synthesize crystalline and magnetic Co doped ZnO nanocomposites for next generation spin-based devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Structure-Related Electronic and Magnetic Properties in Ultrathin Epitaxial Ni x Fe 3–x O 4 Films on MgO(001)

Off-stoichiometric Ni x Fe 3–x O 4 ultrathin films (x < 2.1) with varying Ni content x and thickness 16 (±2) nm were grown on MgO(001) by reactive molecular beam epitaxy. Synchrotron-based high-resolution X-ray diffraction measurements reveal vertical compressive strain for all films, resulting from a lateral pseudomorphic adaption of the film to the substrate lattice without any strain relaxation. Complete crystallinity with smooth interfaces and surfaces is obtained independent of the Ni content x. For x < 1 an expected successive conversion from Fe 3 O 4 to NiFe 2 O 4 is observed, whereas local transformation into NiO structures is observed for films with Ni content x > 1. However, angle-resolved hard X-ray photoelectron spectroscopy measurements indicate homogeneous cationic distributions without strictly separated phases independent of the Ni content, while X-ray absorption spectroscopy shows that also for x > 1, not all Fe 2+ cations are substituted by Ni 2+ cations. The ferrimagnetic behavior, as observed by superconducting quantum interference device magnetometry, is characterized by decreasing saturation magnetization due to the formation of antiferromagnetic NiO parts.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Calculations of anisotropic magnetic properties using spin-orbit energy variations

We analyze several methods of obtaining the accurate relativistic total energy (TE) variations using traditional perturbation theories (PTs) and proposed coupling constant integration (CCI) methods. For this purpose, we perform benchmark calculations within the density functional theory taking the spin-orbit coupling (SOC) and its derivative as a perturbation. The TE change due to SOC addition obtained from both PTs and CCI is shown to reach the accuracy of fully self-consistent TE calculations. Similar accuracy is also obtained even for the magnetocrystalline anisotropy energy (MAE). The real advantage of the proposed methods is to use PTs and CCI methods in those electronic structure methods where accurate total energies currently cannot be obtained with required accuracy. Correspondingly, we demonstrate the applicability of suggested methods for calculations of MAE in different magnetic materials using a dynamic mean-field method. All suggested PTs and CCI methods also provide convenient site, orbital, and spin decompositions of the TE variation, creating a powerful way to analyze microscopic physics in strongly correlated materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Structural and magnetic properties of iodide-mediated chemically synthesized L1 2 FePt 3 nanoparticles

In this work, we study the effect of elemental iodine as a halide intermediary in the synthesis of FePt 3 nanoparticles using a co-reduction of Fe(acac) 3 and (NH 4 ) 2 PtCl 2 with 1,2-hexadecanediol. Our study shows that elemental iodine facilitates the formation of FePt 3 nanoparticles with the L1 2 structure. When iodine is not used, the as-made nanoparticles have mostly the disordered fcc FePt 3 structure. The as-made nanoparticles are ferromagnetic and have a Curie temperature close to 380 K. Annealing of the as-made nanoparticles leads to an increased particle size and a transformation to the ordered L1 2 FePt 3 phase. Nanoparticles annealed at 700°C for 30 minutes show a mixture of two magnetic phases, a ferromagnetic phase with a lower ordering temperature of ~300 K and an antiferromagnetic phase with a Néel temperature around 135 K.

36 MATERIALS SCIENCE↗