Search NASA⌕ Search

SEARCH · Search NASA

Results for “Material microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Supercritical drying of cementitious materials

Techniques to characterize the microstructure of hydrated cement require dried materials. However, the microstructure of hydrated products is significantly altered by high capillary forces during drying when using the conventional drying methods. To avoid drying stresses when preparing samples, we have employed supercritical drying (SCD) which has been used for decades to prepare aerogels that undergo no shrinkage during drying, but has rarely been used for cementitious materials. The pore solution is first replaced with isopropanol, and then with trifluoromethane (R23). The temperature and pressure are raised above the critical point, where no menisci or capillary pressure can exist; therefore, the dried samples are free of artifacts created by stresses. Images from scanning electron microscope show less compact morphology for supercritically dried samples than that dried by conventional methods, while BET surface areas of SCD samples are very close to samples dried by the isopropanol replacement method. This can be explained by the fact that isopropanol and supercritical fluid enter the micropores and block them. The nature of the chemical interactions of isopropanol and R23 with cement pastes are still not clear, but no reaction products were identified in the present study.

36 MATERIALS SCIENCE↗

Microstructure Reconstruction of Sheet Molding Composite Using a Random Chips Packing Algorithm

Fiber-reinforced polymer composites are strong candidates for structural materials to replace steel and light alloys in lightweight vehicle design because of their low density and relatively high strength. In the integrated computational materials engineering (ICME) development of carbon fiber composites, microstructure reconstruction algorithms are needed to generate material microstructure representative volume element (RVE) based on the material processing information. The microstructure RVE reconstruction enables the material property prediction by finite element analysis (FEA)This paper presents an algorithm to reconstruct the microstructure of a chopped carbon fiber/epoxy laminate material system produced by compression molding, normally known as sheet molding compounds (SMC). The algorithm takes the result from material’s manufacturing process as inputs, such as the orientation tensor of fibers, the chopped fiber sheet geometry, and the fiber volume fraction. The chopped fiber sheets are treated as deformable rectangle chips and a random packing algorithm is developed to pack these chips into a square plate. The RVE is built in a layer-by-layer fashion until the desired number of lamina is reached, then a fine tuning process is applied to finalize the reconstruction. Compared to the previous methods, this new approach has the ability to model bended fibers by allowing limited amount of overlaps of rectangle chips. Furthermore, the method does not need SMC microstructure images, for which the image-based characterization techniques have not been mature enough, as inputs. Case studies are performed and the results show that the statistics of the reconstructed microstructures generated by the algorithm matches well with the target input parameters from processing.

Huang, Tianyu↗

TAOI B- Computational Microstructural Optimization Design Tool for High Temperature Structural Materials

The objectives of this research were two-fold: (a) develop a methodology for microstructural optimization of alloys - genetic algorithm approach for alloy microstructural optimization using theoretical models based on fundamental micro-mechanisms, and (b) develop a new computationally designed Ni-Cr alloy for coal-fired power plant applications. The broader outcome of these objectives is expected to be creation of an integrated approach for ‘structural materials by microstructural design’. Three alloy systems were considered for computational optimization and validation, (i) Ni-20Cr (wt.%) base alloy using only solid solution strengthening, (ii) nano-Y 2 O 3 containing Ni-20Cr-1.2Y 2 O 3 (wt.%) alloy for dispersion strengthening and (iii) a sub-micron Al 2 O 3 for composite strengthening, Ni-20Cr-1.2Y 2 O 3 -5.0Al 2 O 3 (wt.%). The specimens were synthesized by mechanical alloying and consolidated using spark plasma sintering. Detailed microstructural characterization was done along with initial mechanical properties to validate the computational prediction. A key target property is to have creep rate of 1x10 -9 s -1 at 100 MPa and 800°C. The initial results were quite promising and require additional quantification of strengthening contributions from dislocation-particle attractive interaction and load transfer. The observed creep rate was in order of 10 -9 s -1 for longer time creep test of Ni-20Cr -1.2Y 2 O 3 -5Al 2 O 3 , lending support to the overall approach pursued in this project.

36 MATERIALS SCIENCE↗

3D Gel-Printing of TiC-Reinforced 316L Stainless Steel: Influence of the Printing Parameters

In this paper, the composite composed of TiC (35 wt.%) reinforced 316L stainless steel matrix was successfully prepared using a 3D gel-printing (3DGP) process. The “step effect” of 3D printing can be reduced using reasonable parameter settings. The properties of TiC/316L slurry for 3DGP and the influence of the different printing parameters on the surface quality of the samples, such as the extrusion overlaps and printing speed, were researched. The microstructure and fracture morphology of the sintered sample were revealed using scanning electron microscopy. The surface roughness, density, and mechanical properties were also measured. When the internal diameter of the nozzle was 0.50 mm, the result showed that the proper extrusion overlap parameter was 0.08 mm and the maximum printing speed was 20 mm/s. Furthermore, the minimum surface roughness value was 10 μm. After sintering, the mechanical performances were similar to those obtained using a conventional powder metallurgy process.

36 MATERIALS SCIENCE↗

Deposition of thin Bi{sub 2}Te{sub 3} and Sb{sub 2}Te{sub 3} films by pulsed laser ablation

Bi{sub 2}Te{sub 3} and Sb{sub 2}Te{sub 3} films were obtained by pulsed laser ablation. The films were deposited in vacuum (1 x 10{sup -5} Torr) on single crystal substrates of Al{sub 2}O{sub 3} (0001), BaF{sub 2} (111), and fresh cleavages of KCl or NaCl (001) heated to 453-523 K. The films were 10-1500 nm thick. The structures of the bulk material of targets and films were studied by X-ray diffractometry and transmission high-energy electron diffraction, respectively. Electrical properties of the films were measured in the temperature range of 77-300 K. It is shown that the films possess semiconductor properties. Several activation portions are observed in the temperature dependences of resistivity; the energies of activation portions depend on the film thickness and crystallite size.

36 MATERIALS SCIENCE↗

Self-Organization and Nitrogen Incorporation in Diamond-Like Carbon Microstructures Synthesized by Nonthermal Plasma

Nonthermal plasma activation of light alkanes is an encouraging decarbonization strategy to produce chemicals or fuels from abundant and/or flared carbon sources. However, prolific carbon growth on both the catalyst and electrode has limited its practicality, requiring additional knowledge of the carbon structure and growth mechanism before breakthroughs are realized. Furthermore, visual evidence is provided for nonuniform diamond-like carbon (DLC) microstructures that materialize in a coaxial dielectric barrier discharge (DBD) reactor flowing ethane and He at 278 K. Through a connection to known behaviors of DBD microdischarge patterns, the microstructure spacing was controlled by altering the applied voltage (ΔV) of the plasma or the burning voltage (U b ). Additionally, carbon valorization through nitrogen incorporation from N 2 was explored as an orthogonal solution to carbon mitigation, with N/C values >0.25 achieved and both sp 2 and sp 3 C–N bonding observed in the microstructures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Inferring topological transitions in pattern-forming processes with self-supervised learning

Abstract The identification of transitions in pattern-forming processes are critical to understand and fabricate microstructurally precise materials in many application domains. While supervised methods can be useful to identify transition regimes, they need labels, which require prior knowledge of order parameters or relevant microstructures describing these transitions. Instead, we develop a self-supervised, neural-network-based approach that does not require predefined labels about microstructure classes to predict process parameters from observed microstructures. We show that assessing the difficulty of solving this inverse problem can be used to uncover microstructural transitions. We demonstrate our approach by automatically discovering microstructural transitions in two distinct pattern-forming processes: the spinodal decomposition of a two-phase mixture and the formation of binary-alloy microstructures during physical vapor deposition of thin films. This approach opens a path forward for discovering unseen or hard-to-discern transitions and ultimately controlling complex pattern-forming processes.

Abram, Marcin↗

Synthesis of High-Purity alpha-and beta-PbO and Possible Applications to Synthesis and Processing of Other Lead Oxide Materials

The red, tetragonal form of lead oxide, alpha-PbO, litharge, and the yellow, orthorhombic form, beta-PbO, massicot, have been synthesized from lead(II) salts in aqueous media at elevated temperature. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were used to characterize the size, morphology, and crystallographic structural forms of the products. The role of impurities in the experimental synthesis of the materials and microstructural variations in the final products are described, and the implications of these observations with respect to the synthesis of different conducting lead oxides and other related materials are discussed.

36 MATERIALS SCIENCE↗

Friction stir welding of multi-walled carbon nanotubes reinforced Al matrix composites

Highlights: • Al/MWCNT composites were successfully welded using friction stir welding. • After FSW, the composites possessed an excellent balance of mechanical properties. • High tensile strength and elongation over BM owing to MWCNTs after FSW. • Microstructures were investigated according to MWCNT contents and FSW conditions. - Abstract: In this study, we prepared composites between Al and multi-walled carbon nanotubes (MWCNTs) using the friction stir welding (FSW) method and investigated their microstructural evolution and mechanical properties by controlling the amount of MWCNT (1 and 3 vol%) and the plunging load (400 and 600 kg) used. After the FSW process, MWCNT showed slight coarsening of grain with random shear textures and accumulated dislocations; the differences obtained by varying the plunging load and MWCNT amount were insignificant. The friction-stir welded composite obtained using 3 vol% MWCNT and a plunging load of 600 kg possessed two-times better balance between strength and ductility than the base metal, due to the presence of both MWCNTs and the partially decomposed Al{sub 4}C{sub 3} in the composite.

36 MATERIALS SCIENCE↗

Mechanisms of Pressure-Induced Phase Transitions by Real-Time Laue Diffraction

Synchrotron X-ray radiation Laue diffraction is a widely used diagnostic technique for characterizing the microstructure of materials. An exciting feature of this technique is that comparable numbers of reflections can be measured several orders of magnitude faster than using monochromatic methods. This makes polychromatic beam diffraction a powerful tool for time-resolved microstructural studies, critical for understanding pressure-induced phase transition mechanisms, by in situ and in operando measurements. The current status of this technique, including experimental routines and data analysis, is presented along with some case studies. The new experimental setup at the High-Pressure Collaborative Access Team (HPCAT) facility at the Advanced Photon Source, specifically dedicated for in situ and in operando microstructural studies by Laue diffraction under high pressure, is presented.

36 MATERIALS SCIENCE↗

Effects of grain morphology, microstructure and dispersed metal cocatalyst on the photoreduction of water over impurity-doped LaInO{sub 3}

Graphical abstract: Grain morphology, doping of an impurity, microstructure, and metal/oxide contacts play a crucial role in the photocatalytic water decomposition activity of metal dispersed LaInO{sub 3}. Highlights: Black-Right-Pointing-Pointer LaInO{sub 3} displays two-step H{sub 2} evolution from UV-induced photoreduction of pure water. Black-Right-Pointing-Pointer Preparation-controlled particle morphology plays a key role in photoactivity. Black-Right-Pointing-Pointer Doping-induced activity enhancement relates to inter-bandgap charge trapping states. Black-Right-Pointing-Pointer Dispersion and metal/oxide contacts may govern the performance of a cocatalyst. -- Abstract: The single phase lanthanum indates doped with Ga (for La) and N (for O), i.e. La{sub 1-x}Ga{sub x}InO{sub 3} (0 {<=} x {<=} 0.2) and LaInO{sub 1-y}N{sub y} (y {approx} 0.6), exhibit significant activity for photoreduction of water; the yield of H{sub 2} produced depending on dopant, excitation source, and addition of a sacrificial reagent. The two-step H{sub 2} evolution observed for this reaction corresponds with the two distinct absorbance regimes displayed by these materials, one in UV-region due to bandgap excitation and the other in visible region arising from the transitions involving sub-bandgap donor or acceptor energy states. The photocatalytic activity of these d{sup 10} metal oxides increases on coating with a metal/metal oxide co-catalyst, gold exhibiting superior activity to Pt and NiO, irrespective of excitation source and sample composition. The preparation-controlled particle morphology, doping-induced lattice imperfections, and metal/semiconductor hetero-junctions are envisaged to play a key role in the absorption characteristics and photocatalytic water reduction activity of metal/LaInO{sub 3} nanocomposites.

36 MATERIALS SCIENCE↗

NEAMS Software V&V Plan for the MARMOT Software

In order to ensure the accuracy and quality of the microstructure based materials models being developed in conjunction with MARMOT simulations, MARMOT must undergo exhaustive verification and validation. Only after this process can we confidently rely on the MARMOT code to predict the microstructure evolution within the fuel. Therefore, in this report we lay out a V&V plan for the MARMOT code, highlighting where existing data could be used and where new data is required.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Impact of Irradiation on Microstructure and Mechanical Properties of Materials Produced by Advanced Manufacturing

Advanced non-light water reactor designs, known as Generation IV (Gen IV) reactors, typically operate at higher temperatures and under more extreme radiation conditions than conventional light water reactors. A critical aspect of the successful deployment and advancement of Gen IV reactor designs is the selection of appropriate structural materials for specific applications, which necessitates the timely development of new materials and manufacturing processes. Advanced manufacturing (AM) offers numerous opportunities for innovative designs, enabling the production of high-performance components with potentially shorter development cycles compared to traditional manufacturing methods. However, a significant challenge in deploying AM technologies in the nuclear energy sector is the current lack of data on the irradiation performance of AM-produced components. This presentation will discuss neutron and ion irradiation results of AM materials, including stainless steel 316L, Grade 91, SA508, Inconel 718, and Inconel 625 materials. The materials were manufactured by AM, such as Powder Metallurgy Hot Isostatic Pressing (PM HIP), Laser Powder Bed Fusion (LPBF) and Directed Energy Deposition (DED). The effects of neutron irradiation on microstructure (e.g., dislocations, loops, and nanoclusters), tensile properties (e.g., strength and ductility), and ion irradiation on Irradiation-Assisted Stress Corrosion Cracking (IASCC) will be explored. Results are collected from several projects supported by the Nuclear Science User Facilities (NSUF) program.

36 - MATERIALS SCIENCE↗

Heatshield Entry Modeling Using a Design, Analysis, and Optimization Toolbox

The Mars Science Laboratory (MSL) was protected during its Mars atmospheric entry by an instrumented heatshield that used NASA's Phenolic Impregnated Carbon Ablator (PICA). PICA is a lightweight carbon fiber/polymeric resin material that offers excellent performances for protecting probes during planetary entry. The Mars Entry Descent and Landing Instrument (MEDLI) suite on MSL offers unique in-flight validation data for models of atmospheric entry and material response. MEDLI recorded, among others, time-resolved in-depth temperature data of PICA using thermocouple sensors assembled in the MEDLI Integrated Sensor Plugs (MISP). The objective of this work is to showcase the capability of the Design, Analysis, and Optimization of Thermal Protection Materials (DAOTPM) software. DAO-TPM is a Python based framework that works as a link between mission design, aerothermal and radiative environment computation, Thermal Protection Systems (TPS) microstructure analysis, material response and optimization tools. The toolbox has a Graphical User Interface (GUI) that allows the user to build as well as run the various software and utilities used to design, analyze and optimize a heatshield during atmospheric entry.

Meurisse, Jeremie B. E.↗

A First Principles Approach to Spectral Phonon Transport in Heterostructures

Understanding thermal transport across interfaces which give rise to a thermal resistance (also known as Kapitza resistance) is a critical issue affecting the development of nanotechnologies. Much modern and emergent nanotechnology consist of adjacent materials, and phonon mediated heat transfer governs thermal behavior across internal interfaces in these devices. The physics of thermal transport in solids are governed both by phenomena occurring at the atomic scale and interactions with the material's microstructure. The forecasting of fundamental quantities such as temperature, heat flux and thermal conductivity typically employs the semi-classical Boltzmann transport equation to predict the macroscopic behavior of materials in terms of the microscopic dynamics of its heat carriers. Kapitza resistance was first discovered in liquid helium experiments and has led to a fundamental research thrust in micro and nano-scale heat transport, the behavior of thermal carriers across internal interfaces. Thermal interfacial resistance (TIR) is a widely studied phenomenon, first engaged by Swartz and Pohl through their development of the acoustic and diffuse mismatch methods, then continued through myriad efforts with varying methods and approaches in an attempt to resolve carrier behavior at thermal interfaces. Many of the fundamental approaches to TIR have been at the nanoscale, and research is conducted with molecular dynamics (MD) and density functional theory (DFT) methods. The limitations of these methods is system size; atomistic methods tend to be limited to system sizes of 100,000 atoms or less. Larger length-scale methods have also been pursued, based on the principles of acoustic or diffuse mismatch, but not all include simulation of TIR using a full phonon band spectrum, or temperature dependent methods. Our approach to enabling phonon transport in layered materials draws upon our previous work of demonstrating spectrally coupled phonon transport in homogeneous and heterogeneous materials. We use a semi-analytical approach in which the Bose-Einstein (B-E) statistics set the strength of the phonon radiance in a frequency group, but the B-E statistics are informed with information from the transport system. The B-E statistics in a single frequency group feels the influence of all the groups through the spatial temperature. We also include a new field term which is an indicator of the amount of non-equilibrium behavior of the phonon spectrum---this is added to the phonon source term in all groups to ensure closure and conservation of energy, as the phonon groups in the transport system and the analytical systems are coupled. This work builds upon our previous approach by adding a phonon coupling term at an internal interface, using the principles of the DMM through transmission and reflection coefficients. In this work, the coefficients are determined through computing a common temperature at the interface, influenced by the phonon band structure of both materials, in effect, providing mixing between the two material systems and using the common temperature to set the strength of the phonon radiance at the boundaries on either side of the interface. Our approach uses material properties computed along various crystallographic orientations, and while some isotropy is built into the interface condition, the material properties weight the phonon distributions in the proper crystalline direction. Greater resolution of phonon behavior in proximity to an interface, and more accurate predictions of TIR are obtained. While it is true the assumption of diffuse mismatch can yield inconsistent results compared to experiment especially at low temperatures, this work focuses on room temperature and beyond effects, for future applications in nuclear fuel, or thermoelectric devices; a modified mismatch approach may be feasible if applied properly. Additionally, our methods focus on bridging mesoscale to engineering scale

36 MATERIALS SCIENCE↗