Search NASA⌕ Search

SEARCH · Search NASA

Results for “Oxidative damage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Synergistic erosion/corrosion of superalloys in PFB coal combustor effluent

Two Ni-based superalloys were exposed to the high velocity effluent of a pressurized fluidized bed coal combustor (PFBC). Targets were 15-cm diameter rotors operating at 40,000 rpm and small flat plate specimens. Above an erosion rate threshold (approximately 10 microns/hr), the targets were eroded to bare metal. The presence of accelerated oxidation at lower erosion rates suggests erosion/corrosion synergism. Various mechanisms which may contribute to the observed oxide growth enhancement include erosive removal of protective oxide layers, oxide and subsurface cracking, and chemical interaction with sulfur in the gas and deposits through damaged surface layers.

Benford, S. M.↗
NASA NTRS1995

TBC experience in land based gas turbines

Prior and on-going machine evaluations of TBC coatings for power generation applications are summarized. Rainbow testing of various TBC's on turbine nozzles, shrouds and buckets are described along with one test on combustor liners. GEPG has conducted over 15 machine tests with TBC coated turbine nozzles of various coatings. Rainbow test times generally range between 10,000 to 24,000 hours. TBC performance has been quite good and additional testing, including TBC's on shrouds and buckets is continuing. The results show that TBC's have the capability of surviving in power generation machines for the times required. The earlier rainbow tests which evaluated various top coat compositions resulted in confirmation of the superiority of YSZ and especially the 6-8 YSZ composition. On-going tests are more focused on TBC process and property variations. The prevalent failure modes seen thus far in the various rainbow tests are erosion, foreign object damage and buildup of deposits. Additional post test analysis is required to investigate bond coat oxidation and other time/temperature dependent changes to the system.

Nelson, W. A.↗
NASA NTRS2000

Test System to Study the Ignition of Metals by Polymers in Oxygen

A new test system that uses Laser energy to ignite a polymer promoter has been developed at the NASA White Sands Test Facility. It will facilitate the study of the spread of fire from a burning polymer material to the metal surrounding it. The system can be used to answer questions regarding the effects of configuration on ignition and combustion. The data obtained from this test could also be used to develop mathematical models for analyzing the effects of configuration on ignition and combustion. The system features a 10,000-psi (69-MPa) test chamber with sight glass windows on either end and a 25-watt carbon dioxide Laser for an ignition source. The test system can be used with gaseous oxygen, nitrogen or any mixture of the two gases. To minimize the effect of preheating the metallic, the polymer is ignited with a minimal amount of Laser energy. Igniting the polymer in this fashion also simplifies the thermodynamic analysis of the ignition and propagation reactions. The system is very robust, versatile and straightforward to use. Depending on the test pressure and configuration, the test system operator can perform as many as 20 tests per day. Test results verify that ignition and combustion of the metallic sample is not only dependent on pressure, material type and temperature, but configuration of both the polymer promoter and metallic sample. Both 6061 aluminum and 316 stainless steel 0.25-inch (6.35-mm) diameter rods with a standard 0-ring groove were tested with Buna-N, Silicone, Teflon and Viton 0-rings. The system ignited all four types of 0-rings in oxygen at pressures ranging from ambient to 10,000 psi (69 MPa). However, neither the stainless steel nor the aluminum rods on which the O-rings were mounted ignited in any test conditions. Future testing may be done on the 0.25-inch (6.35-mm) rod and O-ring configuration to evaluate the lack of ignition in these tests. Future configurations may include a plug of polymer in the base of the sample and replicas of fire-damaged components. Furthermore, the test system may be used in the future to analyze the oxidation rate of Laser-heated metals in gaseous oxygen.

Shoffstall, Michael S.↗
NASA NTRS2001

Automated Tow Placed LaRC(TM)-PETI-5 Composites

LaRC(TM)-PETI-5 is a PhenylEthynyl-Terminated Imide resin developed at NASA Langley Research Center (LaRC) during the 1990s. It offers a combination of attractive composite and adhesive properties. IM7/LaRC(TM)-PETI-5 composites exhibit thermal and thermo-oxidative stability typical of polyimides, superior chemical resistance and processability, excellent mechanical properties, toughness and damage tolerance. It was selected for study in the High Speed Research program aimed at developing technologies for a future supersonic aircraft, the High Speed Civil Transport, with a projected life span of 60 000 h at a cruise speed up to Mach 2.4. Robust autoclave processing cycles for LaRC(TM)-PETI-5 composites have been thoroughly designed and demonstrated, which involved hand lay-up of solvent-ladened 'wet' prepregs. However, this type of processing is not only costly but also environmentally unfriendly. Volatile management and shrinkage could become serious problems in the fabrication of large complex airframe structural subcomponents. Robotic tow placement technology utilizing 'dry' material forms represents a new fabrication process which overcomes these deficiencies. This work evaluates and compares mechanical properties of composites fabricated by heated head automated tow placement (dry process) with those obtained by hand lay-up/autoclave fabrication (wet process). Thermal and rheological properties of the robotically as-placed uncured composites were measured. A post-cure cycle was designed due to the requirement of the PETI-5 resin for a 370 C/1 h hold to reach full cure, conditions which cannot be duplicated during heated head robotic placement. Mechanical properties such as 0 degree flexural strength and modulus, open hole tensile and compressive strength and moduli, reduced section compression dogbone compressive strength, and modified zippora-medium small (MZ-MS) tensile and compressive properties were obtained on the post-cured panels. These properties compared favourably with those obtained from the wet process.

Hou, T. H.↗
DOE OSTI2022

In-situ microstructure observation of oxidized SiC layer in surrogate TRISO fuel particles under krypton ion irradiation

In accidental scenarios of high temperature gas-cooled reactors, both oxidation of and irradiation to the SiC layer in tri-structural-isotropic (TRISO) fuel particles can change the microstructure and integrity of the fuel elements. Here, in the present study, microstructure and defect evolution in the oxidized SiC layer of surrogate TRISO fuel particles under 1.2 MeV krypton ion irradiation was observed by in-situ transmission electron microscopy. The SiC layers oxidized in water vapor at 1200 °C were irradiated azt room temperature and 800 °C and at damage levels of 0.28–11.2 dpa, respectively. SiC and SiO 2 were found to still be in their crystal structures at the damage level of 11.2 dpa at 800 °C, while SiC was observed to have been amorphized at only 0.56 dpa irradiation at room temperature. The defect number density at 800 °C was an order of magnitude lower than that in the sample irradiated at room temperature. Also, crystalline SiO 2 had higher radiation resistance compared to SiC. A defect reaction rate theory was utilized to understand the fundamental defect evolution process and irradiation resistance difference.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Electron energy loss spectroscopy study of ceria sinters and nanoparticles irradiated with swift heavy ions

The electronic energy loss spectra of ceria (CeO 2 ) irradiated with swift heavy ions (27 MeV Xe and 946 MeV Au) in the electronic slowing down regime were measured for bulk sintered samples and nanoparticles by using a double Cs-corrected transmission electron microscope. The low-loss region as well as the core-loss region, including the oxygen K-edge and cerium M 4, 5 white lines, were recorded. No strong lattice disorder was found in the low-loss peaks for both types of samples showing the same bulk oxygen plasmon loss peak at about 15 eV. However, there is a clear evidence of cerium reduction to the trivalent oxidation state after irradiation for the sintered samples as shown by the K-edge shape of oxygen and decrease of the Ce M 4 /M 5 intensity ratio. A similar change of the M 4 /M 5 intensity ratio was observed for the irradiated nanoparticles with respect to the virgin sample owing to the high energy input inside the nanograin. The effect of radiation damage on electron energy loss spectroscopy data is analyzed for both types of samples and irradiation conditions.

Crystallographic defects↗
DOE OSTI2021

Multi-physics Peridynamic Modeling of Damage Processes in Protective Coatings

Protective coatings can revolutionize the aerospace industry by providing a way to build a fuel-efficient and low-emission gas turbine engine operating at elevated temperature. Currently, significant challenges persist in the multi-physics modeling of damage processes in protective coatings exposed to the hot corrosive environment of gas turbine engine. Examples of such detrimental processes include an interface damage between different material layers forming protective coating, a formation of the through-the-thickness vertical cracks, a diffusion of oxygen and moisture through those cracks, an oxidation, and a delamination. In this paper, a feasibility of a multi-physics peridynamic model to provide insight to these detrimental processes has been demonstrated. 3-Dimensional peridynamic equations which are valid everywhere, including dynamically evolving discontinuities, have been presented. In conclusion, validation and demonstration have been shown for conduction heat transfer, reactive oxidation, and delamination of protective coating with a composition borrowed from the open literature.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

A multi-technique approach to understanding delithiation damage in LiCoO2 thin films

Abstract We report on the delithiation of LiCoO 2 thin films using oxalic acid (C 2 H 2 O 4 ) with the goal of understanding the structural degradation of an insertion oxide associated with Li chemical extraction. Using a multi-technique approach that includes synchrotron radiation X-ray diffraction, scanning electron microscopy, micro Raman spectroscopy, photoelectron spectroscopy and conductive atomic force microscopy we reveal the balance between selective Li extraction and structural damage. We identify three different delithiation regimes, related to surface processes, bulk delithiation and damage generation. We find that only a fraction of the grains is affected by the delithiation process, which may create local inhomogeneities. However, the bulk delithiation regime is effective to delithiate the LCO film. All experimental evidence collected indicates that the delithiation process in this regime mimics the behavior of LCO upon electrochemical delithiation. We discard the formation of Co oxalate during the chemical extraction process. In conclusion, the chemical route to Li extraction provides additional opportunities to investigate delithiation while avoiding the complications associated with electrolyte breakdown and simplifying in-situ measurements.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1975

Value contamination avoidance devices

Mechanical redesign methods were used to minimize contamination damage of conventional fluid components and a contamination separator device was developed for long term reusable space vehicles. These were incorporated into an existing 50.8 mm poppet valve and tested for damage tolerance in a full size open loop flow system with gaseous and liquid nitrogen. Cyclic and steady flow conditions were tested with particles of 125 to 420 micrometers aluminum oxide dispersed in the test fluids. Nonflow life tests (100,000 cycles) were made with two valve configurations in gaseous hydrogen. The redesigned valve had an acceptable cycle life and improved tolerance to contamination damage when the primary sealing surfaces were coated with thin coatings of hard plastic (Teflon S and Kynar). Analytical studies and flow testing were completed of four different versions of the separator. overall separation efficiencies in the 55-90% range were measured with these non-optimum configurations.

Endicott, D. L.↗
DOE OSTI2026

Marine algae growth and carbon capture augmentation by antioxidant nanozymes

Large scale commercial cultivation of microalgae year-round is limited by seasonal stress conditions. The rapid growth and high CO 2 capture of the marine microalga Picochlorum celeri is largely inhibited under winter stress conditions of low temperature and high light. Herein, we demonstrated a nanotechnology approach to enhance the biomass productivity and CO 2 capture of P. celeri under abiotic stress by interfacing with antioxidant cerium oxide nanozymes (nanoceria). Antioxidant nanoceria catalytically scavenged reactive oxygen species (ROS) generated under stress conditions, reducing damage to the microalgae photosynthetic machinery in chloroplasts. Negatively charged poly-acrylic acid-coated nanoceria (PNC, 10 μM) were biocompatible in microalgae cells and colocalized with chloroplasts. In contrast, positively charged aminated nanoceria (ANC) resulted in microalgae aggregation (>50 μM) and were toxic at all concentrations tested (≥10 μM). PNC reduction of ROS levels in microalgae (78%) and superoxide levels (26%), enhanced microalgae growth (65%), photosynthetic performance (130%), and CO 2 uptake rate (380%) under low-temperature stress (15 °C) and high light (500 μmol/m 2 /s PAR) stress relative to controls without nanoceria. Nanoceria augmentation of microalgae provides a rapid and facile technology to increase algae CO 2 capture and biomass under stress conditions.

09 BIOMASS FUELS↗
DOE OSTI2020

Efficient Intermolecular Energy Exchange and Soft-ionization of Water at Nanoplatelet Interfaces

X-ray, energetic photon and electron irradiation can ionize and electronically excite target atoms and molecules. These excitations undergo complicated relaxation and energy transfer processes that ultimately determine the manifold of system responses to the deposited excess energy. In weakly bound gas- and solution-phase samples, intermolecular Coulomb decay (ICD) and electron-transfer mediated decay (ETMD) can occur with neighboring atoms or molecules leading to efficient transfer of the excess energy to the surroundings. In ionic solids such as metal-oxides, intra- and inter-atomic Auger decay produces localized final states that lead to lattice damage and typically removal of cations from the substrate. The relative importance of Auger stimulated damage (ASD) versus ICD and ETMD in micro-solvated nanoparticle interfaces is not known. Though ASD is generally expected, essentially no lattice damage and very efficient ICD and ETMD resulting from ionization and electronic excitation of micro-solvated boehmite (AlOOH) nanoplatelets has been observed. Efficient energy transfer and soft ionization of interfacial molecules is likely a general phenomenon at gas-oxyhydroxide nanoparticle interfaces where the density of states of the ionized chemisorbed species significantly overlap the core hole states of the solid.

Jones, Brant M.↗
NASA NTRS1974

Performance and durability of improved air-atomizing splash-cone fuel nozzles

An improved design of air-atomizing fuel nozzles was determined from a study of four differently shaped splash-cone fuel nozzles after 56 hr of durability testing in a combustor segment. Test conditions included fuel-air ratios of 0.008 to 0.018, inlet-air total pressures of 41 to 203 N/cm, inlet-air temperatures of 477 to 811 K, and a reference velocity of 21.3 m/sec. Flat-tip fuel nozzles showed the least erosion damage and at a combustor operating condition of 700 K and 101 N/sq cm an oxides-of-nitrogen emission index of 12 and a smoke number of approximately 18 with a fuel-air ratio of 0.018. Emission indices for carbon monoxide and unburned hydrocarbons were 44 and 16, respectively, at simulated idle conditions of 477 K and 41 N/sq cm.

Ingebo, R. D.↗
NASA NTRS1987

Rapid thermal annealing of indium phosphide compound semiconductors

The rapid thermal annealing (RTA) of indium phosphide (InP) substrates using a proximity contact method and silicon nitride encapsulation is investigated. The surface conditions of the InP substrates following cleaning with procedures A and B are analyzed. Procedure A involves using an iodic acid solution to remove work-damage InP surface layers and B is a degasssing process and hydrofluoric acid solution for native oxide removal. AES, XPS, and SIMS data of the proximity contact and silicon nitride encapsulated annealed samples are examined. The data reveal that RTA using proximity contact with silicon wafers does not provide adequate protection; however, the InP sample is successfully annealed when protected by a silicon nitride encapsulant.

Biedenbender, Michael D.↗
DOE OSTI2022

Probing Distinctive Redox Mechanism in Ni-Rich Cathode Via Real-Time Quick X-Ray Absorption Spectroscopy

X-ray radiation damage on the measuring system has been a critical issue regularly for a long-time exposure to X-ray beam during the in operando characterizations, which is particularly severe when the applied X-ray energy is near the absorption edges (M, L, K, etc.) of the interest element. Here, to minimize the negative effects raised by beam radiation, we employ quick X-ray absorption spectroscopy (QXAS) to study the electrochemical reaction mechanism of a Ni-rich layered structure cathode for lithium-ion batteries. With the advanced QXAS technique, the electronic structure and local coordination environment of the transition metals (TMs) are monitored in-operando with limited radiation damage. Compared to the conventional step-mode X-ray absorption spectroscopy, the QXAS can provide more reliable oxidation state change and more detailed local structure evolutions surrounding TMs (Ni and Co) in Ni-rich layered oxides. By leveraging these advantages of QXAS, we demonstrated that the Ni dominates the electrochemical process with the Co being almost electrochemically inactive. Reversible Ni ions movement between TMs sites and Li sites is also revealed by the time-resolved QXAS technique.

25 ENERGY STORAGE↗
DOE OSTI2026

A Multicopper Oxidase from Paenibacillus Polyethylenelyticus JNU01 Oxidizes Polyethylene

Polyethylene (PE) is a widely used plastic that persists in the environment and resists breakdown via microbial degradation. In this work, we discovered a new bacterium, Paenibacillus polyethylenelyticus JNU01, that grows on a PE-like wax (PELW, 4 kDa) as its sole carbon source, causing chemical modifications to the substrate and releasing small-molecule products. Genomic and transcriptomic analyses identified a multicopper oxidase (PpMmcO) as a key enzyme candidate for this observed activity. PpMmcO promoted surface oxidation, increased hydrophilicity, and the release of small-molecule products such as ketones, alkanes, and alkenoic acids. Scanning electron microscopy confirmed surface damage on both PELW and post-use greenhouse PE films. Weight loss analysis showed mass losses of 5.2% for the PELW powder and 1.6% for the greenhouse PE film after treatment with wild-type PpMmcO. We propose a radical-mediated pathway catalyzed by PpMmcO. These findings identify a new bacterium and enzyme capable of promoting partial PE oxidation and provide insight into biological processes that may act on polyethylene.

36 MATERIALS SCIENCE↗
NASA NTRS1988

Surface-catalyzed air oxidation of hydrazines: Environmental chamber studies

The surface-catalyzed air oxidation reactions of fuel hydrazines were studied in a 6500-liter fluorocarbon-film chamber at 80 to 100 ppm concentrations. First-order rate constants for the reactions catalyzed by aluminum, water-damaged aluminum (Al/Al2O3), stainless steel 304L, galvanized steel and titanium plates with surface areas of 2 to 24 sq m were determined. With 23.8 sq m of Al/Al2O3 the surface-catalyzed air oxidation of hydrazine had a half-life of 2 hours, diimide (N2H2) was observed as an intermediate and traces of ammonia were present in the final product mixture. The Al/Al2O3 catalyzed oxidation of monomethylhydrazine yielded methyldiazine (HN = NCH3) as an intermediate and traces of methanol. Unsymmetrical dimethylhydrazine gave no detectable products. The relative reactivities of hydrazine, MMH and UDMH were 130 : 7.3 : 1.0, respectively. The rate constants for Al/Al2O3-catalyzed oxidation of hydrazine and MMH were proportional to the square of the surface area of the plates. Mechanisms for the surface-catalyzed oxidation of hydrazine and diimide and the formation of ammonia are proposed.

Kilduff, Jan E.↗
DOE OSTI2023

An Introduction to Radiation Damage in Minerals and Ceramics [Slides]

Radiation effects in minerals and ceramics are quite distinct from effects observed in metals. This is largely due to interactions between radiation and the electronic structure of insulating materials that are unique compared to metallic conductors. Most notably, insulators exhibit property changes when energetic particles lose energy to electrons in the solid, whereas metals are unaffected by electronic energy losses. In addition, displacive radiation damage effects (atoms being knocked off their lattice sites by energetic particles) are much more complex in insulators, due to the complexities of their crystal structures (multiple cation and anion sublattices). In this presentation, we will focus on the atomistic mechanisms responsible for radiation damage in minerals and ceramics, when energetic particles lose energy while penetrating a solid. We will consider several examples, including (i) irradiation induced color center formation in gemstones; (ii) latent defects in alkali halides (relevance to thermoluminescent detectors); (iii) radioactive decay-induced amorphization of natural minerals; and (iv) extended defect formation and phase stability in complex oxides.

36 MATERIALS SCIENCE↗