Search NASA⌕ Search

SEARCH · Search NASA

Results for “PIN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

A Fast Reactor Irradiation Experiment Design in the ATR

Modern modeling techniques were used to investigate a proposed method for fast neutron irradiations in an existing thermal-spectrum reactor, the Advanced Test Reactor (ATR). This method builds upon pre-existing ideas, where fast flux is increased by surrounding the specimens with fissionable “booster fuel” but diverges from historical approaches by using an already developed fuel element design used in the Belgian Reactor 2 (BR2) as the booster fuel while leveraging modern 3-D modeling and simulation techniques. Design evaluations and neutronics simulations were performed to evaluate the performance of a BR2 fuel element irradiated in an ATR flux trap with test pins in the central channel of the BR2 fuel element. These efforts have yielded promising results. Adding a BR2 fuel element in the northeast (NE) flux trap of ATR was predicted to result in a 150% increase to the incident fast neutron flux with a fast (>0.1 MeV) to thermal (<0.625 eV) neutron flux ratio ranging from approximately 50 to 150, dependent on the material used for thermal neutron filtering and volume of moderator within the central channel of the BR2 element. The predicted annual fast neutron fluence (>0.1 MeV) ranges from 7.9 × 1021 to 9.1 × 1021 n/cm2. Given the relatively large fast to thermal neutron flux ratio, the calculated radial power profiles within 4.3 mm outer diameter U10Zr fueled specimens irradiated within the BR2 booster fuel element are adequate representations of those within fast neutron reactors. The predicted radial power profiles are not flat, but they are more prototypic than those seen in advanced fuels tests which began in ATR in 2003. Another distinct advantage of this experiment design is that full-scale test pins can be irradiated to augment the ongoing series of reduced scale advanced fuels tests. The proposed experiment design irradiated within a BR2 fuel element in a flux trap of ATR offers an improved alternative to the current testing of advanced reactor fuels in ATR. Selected results from this design evaluation are presented.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Methods and devices for electrochemical relithiation of lithium-ion batteries

Among other things, the present disclosure relates to re-purposing used lithium-ion batteries. The present disclosure includes treating an electrode using a solvent prior to electrochemically relithiating the electrode. In some embodiments, the relithiation may be done using a roll-to-roll device, wherein the electrode may be secured on a first pin and a second pin, then it may be unwound and submerged in an electrolyte solution. Lithium ions may be inserted into the electrode using a voltage. The layer of lithium may provide lithium ions to the electrode.

Smith, Kandler Alan↗
DOE OSTI2025

Examining Constituent Redistribution in U-19Pu-10Zr Fuel as it Evolves with Local Burnup

While constituent redistribution is a known irradiation behavior in U-Pu-Zr fuel, new data have shown it is more complex than our current understanding and predictive capabilities. The size and composition of redistributed rings evolve as a function of pin composition, burnup, geometry, and irradiation temperature. In this work, we extract microstructural information from optical microscopy conducted on U-19Pu-10Zr pins (irradiated between 1.9 at. % and 11.6 at. % peak burnup). Both manual image analysis techniques and machine learning-assisted segmentation are used to quantify the thicknesses of the cladding, fuel-cladding interaction layers, and rings of fuel constituent redistribution in addition to pore distribution. These microstructural features and individual redistributed regions affect local thermomechanical properties, and identifying the relationship between burnup and constituent redistribution will improve accurate prediction of advanced reactor fuel performance.

Constituent Redistribution↗
DOE OSTI2025

Peer Review of X441A Fission Gas Release Data

The purpose of this document is to demonstrate completion of the independent peer review for the fission gas release measurement of fuel pins irradiated in the Experimental Breeder Reactor-II (EBR-II) as part of the X441A experiment. The specific data reviewed includes reported plenum volume and pressure from the measurement from the fuel pins. Fraction percent of fission gas release is derived in part from these measurements but is excluded from the data reviewed.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Demonstration of a Three-Dimensionally Structured Betavoltaic

In this work, we present a demonstration of a high-aspect ratio, three-dimensionally structured betavoltaic device. High-aspect ratio silicon PIN diodes were used as the semiconductor absorber and 147 PmCl 3 was used as the beta emitter. Three devices were fabricated with 147 Pm activities of 2.4 mCi, 7.4 mCi, and 29.5 mCi. The device with the highest activity produced an initial power output of 200 nW and was monitored over a period of 8 months to observe the current–voltage behavior over time, during which time the output current decreased in accordance with the radioactive half-life of 147 Pm. Small deviations in the output current of a few percent during the long-term measurement were found to be attributable to the humidity in the room where the experiment was done. Furthermore, the output current generated from the devices was 68–77% of the theoretical maximum, indicating significant infiltration of the radioisotope into the ridged structures.

42 ENGINEERING↗
DOE OSTI2022

Nanostructure refinement and phase formation of flash annealed FeNi-based soft magnetic alloys

In this work, the resulting nanocomposite microstructures of FeNi nanocrystallites under different heating and cooling rates (5 °C/min vs 400-500 °C/s) is investigated. Conventional furnace annealing under low heating rates and slow cooling resulted in both BCC α-FeNi and FCC γ-FeNi nanocrystallites with an average grain size on the order of 25-27 nm whereas high heating rates achieved via flash annealing techniques have enabled a dramatically refined microstructure consisting of 5-7 nm grains with FCC γ-FeNi phase and found to be the dominant phase following primary crystallization. Grain size refinement and phase identity optimization yielded low values of coercivities-17 A/m and high permeability similar to 11 x 10 3 measured at 400 Hz/1 kA/m in flash annealed samples at 450 °C for 5 s. The magnetic behavior and the underlying mechanism of optimal soft magnetic properties are discussed in terms of the critical role of the grain size in domain wall pinning and coercivity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Imaging Reconfigurable Molecular Concentration on a Graphene Field-Effect Transistor

The spatial arrangement of adsorbates deposited onto a clean surface under vacuum typically cannot be reversibly tuned. Here we use scanning tunneling microscopy to demonstrate that molecules deposited onto graphene field-effect transistors (FETs) exhibit reversible, electrically tunable surface concentration. Continuous gate-tunable control over the surface concentration of charged F 4 TCNQ molecules was achieved on a graphene FET at T = 4.5K. This capability enables the precisely controlled impurity doping of graphene devices and also provides a new method for determining molecular energy level alignment based on the gate-dependence of molecular concentration. Gate-tunable molecular concentration is explained by a dynamical molecular rearrangement process that reduces total electronic energy by maintaining Fermi level pinning in the device substrate. Finally, the molecular surface concentration is fully determined by the device back-gate voltage, its geometric capacitance, and the energy difference between the graphene Dirac point and the molecular LUMO level.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Coalescence-Induced Spontaneous Shedding of Microdroplets on Superhydrophobic Surfaces Featuring Enclosed Micropillars with Hierarchical Roughness

This study investigated water vapor condensation on superhydrophobic surfaces (SHSs) featuring micropillars enclosed by wall lattices and having three-tier hierarchical roughness. A total of five samples were created with three (NW-J, W200-J and W400-J samples) having large micropillar depth (~6 μm) and two (NW-S and W200-S samples) having small micropillar depth (~1 μm). Two distinct condensate removal modes were observed during condensation: coalescence-induced jumping on samples with large micropillar depth and coalescence-induced shedding on samples with small micropillar depth. The results showed that the diameter of the shedding droplet on the W200-S sample having small micropillar depth could be as small as 107 μm, as compared to the theoretical critical diameter of 267 μm for gravitational shedding on the same sample. The enhanced functionality of the three-tier nanotextures on the W200-S sample could effectively suppress localized pinning of the three-phase contact line and Wenzel neck formation during the growth of condensate droplets. Consequently, during multidroplet coalescence, the released surface energy easily overcomes the solid–liquid adhesion, leading to spontaneous shedding of merged droplets. The inclusion of the wall lattice aids condensate growth by the droplet self-alignment along the walls and promoting coalescence. As a result, the W200-S sample exhibited the highest condensate collection as well. In conclusion, the proposed surface design has great potential for scaling up and implementation in heating, ventilation, and air-conditioning equipment due to the simplicity of the surface morphology and the facile spray-coating method used to achieve hierarchical roughness.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Visualizing the strongly reshaped skyrmion Hall effect in multilayer wire devices

Magnetic skyrmions are nanoscale spin textures touted as next-generation computing elements. When subjected to lateral currents, skyrmions move at considerable speeds. Their topological charge results in an additional transverse deflection known as the skyrmion Hall effect (SkHE). While promising, their dynamic phenomenology with current, skyrmion size, geometric effects and disorder remain to be established. Here we report on the ensemble dynamics of individual skyrmions forming dense arrays in Pt/Co/MgO wires by examining over 20,000 instances of motion across currents and fields. The skyrmion speed reaches 24 m/s in the plastic flow regime and is surprisingly robust to positional and size variations. Meanwhile, the SkHE saturates at ~22 ° , is substantially reshaped by the wire edge, and crucially increases weakly with skyrmion size. Particle model simulations suggest that the SkHE size dependence - contrary to analytical predictions - arises from the interplay of intrinsic and pinning-driven effects. These results establish a robust framework to harness SkHE and achieve high-throughput skyrmion motion in wire devices.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Space charge limited corrections to the power figure of merit for diamond

An interpretation of the unipolar figure of merit is formulated for wide bandgap (WBG) semiconductors based on the on-state specific resistance (RON,sp) derived from the space charge limited current–voltage relationship (Mott–Gurney square law). The limitations of the traditional Ohmic R ON,sp for WBG semiconductors are discussed, particularly at low doping, while the accuracy of the Mott–Gurney based R ON,sp is confirmed by Silvaco ATLAS drift–diffusion simulations of diamond Schottky pin diodes. The effects of incomplete ionization are considered as well.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Investigation of the effect of structural defects from hydride precipitation on superconducting properties of high purity SRF cavity Nb using magneto-optical and electron imaging methods

Abstract Nb is an elemental superconductor with a critical temperature of 9.3 K and is widely used to fabricate superconducting radiofrequency (SRF) cavities for particle accelerators. However, microstructural defects in Nb, such as grain boundaries (GBs) and dislocations, can act as pinning centers for magnetic flux that can degrade SRF cavity performance. Hydrogen contamination is also detrimental to SRF cavity performance due to the formation of normal conducting hydrides during cool down. In this study, disc shaped Nb bi-crystals extracted from high-purity large-grain Nb slices were investigated to study the effects of GBs, hydrogen, and dislocations on superconducting properties. Grain orientation and GB misorientation were measured using Laue x-ray diffraction and electron backscattered diffraction (EBSD) analyses. Cryogenic magneto-optical imaging was used to directly observe magnetic flux penetration below T c = 9.3 K. Damage caused by low temperature precipitation of hydrides and their dissolution upon reheating after cryogenic cycles was examined using electron channeling contrast imaging, and EBSD. The relationships between hydride formation, dislocation content, GBs, cryo-cooling, heat treatment (HT), and flux penetration indicate that both GB character and hydrogen content affect magnetic flux penetration. Such flux penetration could be facilitated by dislocation structures and low angle GBs resulting from hydride precipitation and HT.

36 MATERIALS SCIENCE↗
DOE OSTI2023

APC Nb 3 Sn superconductors based on internal oxidation of Nb–Ta–Hf alloys

In the last few years, a new type of Nb 3 Sn superconducting composite, containing a high density of artificial pinning centers (APC) generated via an internal oxidation approach, has demonstrated a significantly superior performance relative to present, state-of-the-art commercial Nb3Sn conductors. This was achieved via the internal oxidation of Nb-4at.%Ta-1at.%Zr alloy. On the other hand, our recent studies have shown that internal oxidation of Nb–Ta–Hf alloys can also lead to dramatic improvements in Nb 3 Sn performance. Here in this work we follow up on this latter approach, fabricating a 61-stack APC wire based on the internal oxidation of Nb-4at.%Ta-1at.%Hf alloy, and compare its critical current density (J c ) and irreversibility field with APC wires made using Nb-4at.%Ta-1at.%Zr. A second goal of this work was to improve the filamentary design of APC wires in order to improve their wire quality and electromagnetic stability. Our new modifications have led to significantly improved residual resistivity ratio and stability in the conductors, while still keeping non-Cu J c at or above the conductor J c specification required by the proposed Future Circular Collider. Further improvement via optimization of the wire recipe and design is ongoing. Finally, additional work needed to make APC conductors ready for applications in magnets is discussed.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Superfluid weight of strongly inhomogeneous superconductors

In this study, we obtain the superfluid weight of strongly inhomogeneous superconductors. We find that, in general, the response of the superconductor’s pairing potential to the perturbing vector potential is essential to obtain the correct value of the superfluid weight. We consider two exemplary cases: the case when strong inhomogeneities in the pairing potential are induced by a periodic potential, and the case when superconducting vortices are induced by an external magnetic field. For both cases we show that the correction to the superfluid weight due to the response of the paring potential to the perturbing vector potential can be significant, it must be included to obtain quantitatively correct results, and that for the case when vortices are present the expression of the superfluid weight that does not include such correction returns qualitatively wrong results. The results are directly relevant for superconducting states in moiré multilayer where the almost inevitable spatial variations of the magic angle and the proximity of superconductivity to anisotropic phases induce inhomogeneities in the pairing potential, and to the efforts to optimally pin superconducting vortices to achieve large superconducting critical currents.

Bogoliubov-de Gennes equations↗
DOE OSTI2024

VitroJet: new features and case studies

Single-particle cryo-electron microscopy has become a widely adopted method in structural biology due to many recent technological advances in microscopes, detectors and image processing. Before being able to inspect a biological sample in an electron microscope, it needs to be deposited in a thin layer on a grid and rapidly frozen. The VitroJet was designed with this aim, as well as avoiding the delicate manual handling and transfer steps that occur during the conventional grid-preparation process. Since its creation, numerous technical developments have resulted in a device that is now widely utilized in multiple laboratories worldwide. It features plasma treatment, low-volume sample deposition through pin printing, optical ice-thickness measurement and cryofixation of pre-clipped Autogrids through jet vitrification. This paper presents recent technical improvements to the VitroJet and the benefits that it brings to the cryo-EM workflow. A wide variety of applications are shown: membrane proteins, nucleosomes, fatty-acid synthase, Tobacco mosaic virus, lipid nanoparticles, tick-borne encephalitis viruses and bacteriophages. These case studies illustrate the advancement of the VitroJet into an instrument that enables accurate control and reproducibility, demonstrating its suitability for time-efficient cryo-EM structure determination.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

A Reconfigurable Planar Capacitor Sensor for Thru the Jacket Dielectric Constant Measurement of Cable Insulation

Planar capacitor sensors have been proposed to measure the aging-related dielectric constant variation of the jacket or insulation materials of cables. Although capacitor sensors have been used to monitor the aging of cable insulation by removing the jacket, through the jacket measurement of cable insulation dielectric constant variation is difficult because once the sensor is placed on the jacket it would either measure the aging of the jacket or that of the jacket and insulation together. A reconfigurable sensor along with innovative cable-specific models could be used to determine the jacket and insulation aging using the same sensor. For the proposed novel reconfigurable sensor, the electric field penetration depth is changed by activating and deactivating PIN diode switches. In one instance, the sensor measures the dielectric constant variation of the jacket, while in the next, it measures the dielectric constant variation of both the jacket and the insulation. Here, by leveraging previously developed capacitance estimation models from large-scale finite element simulations for a specific cable, these two sets of measurement data are used to evaluate the aging-related dielectric constant variation of the insulation. Experimental data from aged cable specimens are presented to demonstrate the operation of the sensor.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Power Conversion Systems Enabled by SiC BiDFET Device

The BiDirectional Field-Effect Transistor (BiDFET) can enable circuit topologies requiring four quadrant switches, that were earlier designed using discrete combinations of MOSFETs, IGBTs, GaN HEMTs and PiN diodes. The monolithic nature of the BiDFET allows lower device count, smaller switch volume, lower inductance, and simpler packaging, and hence more reliable and commercially viable implementation in power electronics converters. Furthermore, the matrix converter topologies, now feasible using BiDFETs, can eliminate the bulky and unreliable dc link capacitors or inductors required for conventional voltage-source or current-source converters in ac-ac and ac dc applications. The 1.2 kV BiDFET has the potential to disrupt all the applications utilizing 1.2 kV switches, including electric vehicle (EV) drivetrain, bidirectional EV chargers, industrial motor drives, solid-state transformers, datacenter power supplies, elevator drives, dc microgrids, energy storage grid integration, solid-state breakers, etc.

42 ENGINEERING↗
DOE OSTI2024

Enhanced Second Generation (2G) High Temperature Superconducting (HTS) wire for Electric Motor Applications

This project focused on the development of a revolutionary Second Generation (2G) high temperature superconducting (HTS) wire engineered specifically to meet the requirements for a new generation of high temperature superconducting electric machines. This novel design combined a roll-to-roll irradiation process to enhance the performance of the HTS wire in the presence of strong magnetic fields (improved flux pinning) with an innovative process to incorporate multiple HTS layers within a single 2G wire.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Nanostructured Oxide-Dispersion-Strengthened CoCrFeMnNi High-Entropy Alloys with High Thermal Stability

A nanostructured oxide-dispersion-strengthened (ODS) CoCrFeMnNi high-entropy alloy (HEA) is synthesized by a powder metallurgy process. The thermal stability, including the grain size and crystal structure of the HEA matrix and oxide dispersions, is carefully investigated by X-ray diffraction (XRD) and electron microscopy characterizations after annealing at 900 °C. The limited grain growth may be attributed to Zener pinning of yttria dispersions that impede the grain boundary mobility and diffusivity. The high hardness is caused by both the fine grain size and yttria dispersions, which are also retained after annealing at 900 °C. In this study, it is implied that the combination of ODS and HEA concepts may provide a new design strategy for the development of thermally stable nanostructured alloys for extreme environments.

36 MATERIALS SCIENCE↗