Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLATELET”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Phase transformation during mechano-synthesis of nanocrystalline/amorphous Fe–32Mn–6Si alloys

Mechano-synthesis of Fe–32Mn–6Si alloy by mechanical alloying of the elemental powder mixtures was evaluated by running the ball milling process under an inert argon gas atmosphere. In order to characterize the as-milled powders, powder sampling was performed at predetermined intervals from 0.5 to 192 h. X-ray florescence analyzer, X-ray diffraction, scanning electron microscope, and high resolution transmission electron microscope were utilized to investigate the chemical composition, structural evolution, morphological changes, and microstructure of the as-milled powders, respectively. According to the results, the nanocrystalline Fe–Mn–Si alloys were completely synthesized after 48 h of milling. Moreover, the formation of a considerable amount of amorphous phase during the milling process was indicated by quantitative X-ray diffraction analysis as well as high resolution transmission electron microscopy image and its selected area diffraction pattern. It was found that the α-to-γ and subsequently the amorphous-to-crystalline (especially martensite) phase transformation occurred by milling development. - Graphical abstract: Mechano-synthesis of nanocrystalline/amorphous Fe–32Mn–6Si shape memory alloys in the powder form: amorphous phase formation, α-to-γ phase transformation, mechano-crystallization of the amorphous, and martensite phase formation during the process. Highlights: • During MA, the α-to-γ phase transformation and amorphization occurred. • Mechano-crystallization of the amorphous phase occurred at sufficient milling time. • The formation of high amount of ε-martensite was evidenced at high milling times. • The platelet, spherical, and then irregular particle shapes was extended by MA. • By MA, the particles size was increased, then reduced, and afterward re-increased.

36 MATERIALS SCIENCE↗

In-situ measurement of phase transformation kinetics in austempered ductile iron

Austempered ductile iron (ADI) alloyed with 0.42% Mn and 0.72% Cu was heat treated in a mirror furnace and the phase transitions were studied in-situ by neutron diffraction. The heat treatment consisted of austenitisation at 920 °C and isothermal austempering at 400 °C, 350 °C and 300 °C, respectively. Due to the growth of ferrite platelets, the austenite content decreases rapidly at all temperatures within the first 15–20 min and reaches a stable plateau after 35 min (400 °C) to 80 min (300 °C). The carbon content of the residual austenite, which was monitored and characterised by the change of the lattice parameter, increases up to 1.6 wt.% caused by redistribution from the newly formed ferrite. While at higher austempering temperatures this takes place almost parallel to the phase transformation, at 300 °C the redistribution of carbon to austenite lags behind considerably. Furthermore the neutron data revealed an austenite peak asymmetry during austempering which is attributed to successive phase transformation. It results temporarily in two fractions of austenite, an initial low-carbon and an enriched high-carbon modification. - Highlights: • The heat treatment of ADI was studied in detail by in-situ neutron diffraction. • The phase fractions were monitored and evaluated quantitatively. • The austenite carbon content increased up to 1.6 wt.% during austempering. • Peak asymmetries indicate two austenite fractions during highest transformation rates.

36 MATERIALS SCIENCE↗

In situ CrB{sub 2} and its effect on the mechanical properties of A390 alloy

In this work, a series of CrB{sub 2}/A390 composite alloys have been prepared and analyzed by a field emission scanning electron microscope (FESEM) and X-ray diffraction (XRD). Firstly, in situ CrB{sub 2} has been prepared by reducing reaction that occurred in Al melt: AlB{sub 2} + [Cr] → Al + CrB{sub 2}. The CrB{sub 2} particles exhibit regular hexagonal platelet morphology and distribute uniformly in the Al matrix. Then, A390 alloys with different CrB{sub 2} additions have been prepared. With the addition of CrB{sub 2}, the size of primary Si can be reduced remarkably. The generation of CrB{sub 2} particles and their diffuse distribution can improve the mechanical properties of A390 alloy obviously. The mechanical properties of the base alloy, including ultimate tensile strength at 25 °C (UTS{sub 25°C}), the coefficient of thermal expansion (CTE) and wear resistance have been studied and the composite alloy with 3 wt.% CrB{sub 2} particle addition showed the best performance. - Highlights: • CrB2/A390 composite alloy was successfully fabricated at 850 °C. • The reaction between AlB2 and Cr was investigated. • The possible coherent interface of CrB2 and Si was calculated. • Mechanical properties of A390 alloy are improved with the addition of CrB2.

36 MATERIALS SCIENCE↗

Effect of long-term aging on microstructure and local behavior in the heat-affected zone of a Ni–Cr–Mo–V steel welded joint

Evolution of microstructure, micro-hardness and micro-tensile strength behavior was investigated in the heat-affected zone of a Ni–Cr–Mo–V steel welded joint after the artificial aging at 350 °C for 3000 h. After detailed characterization of microstructures in optical microscopy, scanning electron microscopy and transmission electron microscopy, it is revealed that the change of martensite–bainite constituent promotes more homogeneous microstructure distribution. The aging treatment facilitates redistribution of carbon and chromium elements along the welded joint, and the micro-hardness is increased slightly through the welds due to enrichment of carbon. The types of precipitates in the weldment mainly include M{sub 3}C, MC, M{sub 2}C and M{sub 23}C{sub 6}. The carbides in base metal, weld metal and coarse-grained heat-affected zone are prone to change from ellipsoidal to platelet form whereas more uniform spherical carbides are observed in the fine-grained zone. Precipitation and coarsening of M{sub 23}C{sub 6} near the fusion line, and formation of MC and M{sub 2}C, are responsible for the tensile strength decrease and its smooth distribution in the aged heat-affected zone. This implies that the thermal aging can relieve strength mismatch in the weldments. - Highlights: • Microstructure homogeneity improved in HAZ after long-term aging. • Tensile strength decreased in HAZ due to precipitation and coarsening of M{sub 23}C{sub 6}. • Strength mismatch in NiCrMoV steel welds was relieved after aging at 350 °C × 3000 h.

36 MATERIALS SCIENCE↗

Microstructural characterization of Charpy-impact-tested nanostructured bainite

In this work, a possible cause of the extraordinary low impact toughness of nanostructured bainite has been investigated. The microstructure of nanostructured bainite consisted chiefly of carbide-free bainitic ferrite with retained austenite films. X-ray diffractometry (XRD) measurement indicated that no retained austenite existed in the fractured surface of the Charpy-impact-tested specimens. Fractographs showed that cracks propagated mainly along bainitic ferrite platelet boundaries. The change in microstructure after impact loading was verified by transmission electron microscopy (TEM) observations, confirming that retained austenite was completely transformed to strain-induced martensite during the Charpy impact test. However, the zone affected by strained-induced martensite was found to be extremely shallow, only to a depth of several micrometers from the fracture surface. It is appropriately concluded that upon impact, as the crack forms and propagates, strain-induced martensitic transformation immediately occurs ahead of the advancing crack tip. The successive martensitic transformation profoundly facilitates the crack propagation, resulting in the extremely low impact toughness of nanostructured bainite. Retained austenite, in contrast to its well-known beneficial role, has a deteriorating effect on toughness during the course of Charpy impact. - Highlights: • The microstructure of nanostructured bainite consisted of nano-sized bainitic ferrite subunits with retained austenite films. • Special sample preparations for SEM, XRD and TEM were made, and the strain-affected structures have been explored. • Retained austenite films were found to transform into martensite after impact loading, as evidenced by XRD and TEM results. • The zone of strain-induced martensite was found to extend to only several micrometers from the fracture surface. • The poor Charpy impact toughness is associated with the fracture of martensite at a high strain rate during impact loading.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of extruded Mg-Gd-Y-Zn-Zr alloys filled with intragranular LPSO phases

Highlights: • Intragranular thin-platelet LPSO phases strongly restrict the DRX. • The low extrusion ratio fails to widely break the intragranular LPSO. • The large extrusion ratio results in the full DRX via the CDRX mechanism. • Finer DRX-ed grains and LPSO induce the higher yield strength and elongation. • The larger grain size causes an increase in the strain hardening rate. - Abstract: A comparison has been made on the dynamic recrystallization (DRX), texture, and mechanical properties of the Mg-5.5Gd-4.4Y-1.1Zn-0.5Zr (wt%) alloys extruded with different ratios (ER, 36 and 7.1). Intragranular long-period stacking ordered (LPSO) phases strongly restrict the DRX by restraining the lattice rotation of α-Mg grains and hindering the migration of the boundaries of DRX-ed grains. Extrusion with ER of 36 can widely break the intragranular LPSO phases and create a fully DRX-ed microstructure with a relatively random texture, while the lower ER of 7.1 fails to break the LPSO and leads to a bimodal microstructure with a strong basal fiber texture. Finer DRX-ed grains and smaller LPSO phases account for the superior tensile yield strength and elongation of the ER36 alloy. However, the ultimate tensile strength of the ER7.1 alloy catches up because its larger grain size causes an increase in the strain hardening rate.

36 MATERIALS SCIENCE↗

Changing the solidification sequence and the morphology of iron-containing intermetallic phases in AA6061 aluminum alloy processed by spray forming

Highlights: • Spray forming alters the solidification path of the Fe contaminated AA 6061 alloy. • Thus forming primary α-Al{sub 15}(Fe, Mn){sub 3}Si{sub 2} with polyhedral morphology • Thus preventing the formation of AlFeSi with deleterious morphology • Despite Fe contamination final microstructure presented important ductility. - Abstract: Typically, aluminum alloys are contaminated by iron during recycling cycles. Such a procedure leads to the formation of intermetallic phases with detrimental morphology, which acts as stress risers, impairing mechanical properties and consequently hindering further mechanical processing and restricting recycling. This paper aimed at studying the solidification of an AA6061 alloy highly contaminated with iron (1.4 wt%). Spray forming processing allowed altering the solidification path of the Fe-modified AA 6061 alloy, resulting in the formation of primary α-Al{sub 15}(Fe, Mn){sub 3}Si{sub 2} phase with polyhedral morphology, which traps Fe and Si at elevated temperature. Furthermore, spray forming prevented the formation of intermetallic AlFeSi phases with platelet-like morphology, such as β-AlFeSi as well as the typical Chinese script morphology, resulting in a final ductile microstructure, allowing further processing by hot extrusion.

36 MATERIALS SCIENCE↗

Site-specific nanoscale characterization of zirconium hydrides in the hydride rim structure of hydrogen-charged zircaloy-4 cladding

Zircaloy-4 cladding tubes were hydrogen-charged using a static pressure hydrogen charging method to experimentally produce a zirconium-hydride rim structure similar to that observed in Zircaloy-4 cladding tubes after operation in commercial light-water nuclear reactors. Detailed characterization was performed using electron energy loss spectroscopy (EELS) and four-dimensional scanning transmission electron microscopy (4D-STEM). By mapping the position of the plasmon peak in the low-loss EELS spectrum, it was determined that the zirconium hydrides formed were predominantly solid δ-phase zirconium hydrides. 4D-STEM was used to generate phase and strain maps at nanoscale. The interactions between two zirconium hydride platelets less than 200 nm apart leads to the localized lattice rotations and possible phase change, revealing a potential hydride growth mechanism.

4D-STEM↗

Crystal growth and structure refinement of monoclinic Li{sub 2}TiO{sub 3}

Colorless platelet crystals of monoclinic Li{sub 2}TiO{sub 3} with a maximum size of 5.0 mm x 5.0 mm x 0.5 mm were successfully grown by a flux method at 1373 K using a LiBO{sub 2}-Li{sub 2}O system flux. The stoichiometric chemical composition of Li{sub 2}TiO{sub 3} was determined by the SEM-EDX, ICP-AES and density measurement using the single crystal samples. The thermal conductivity of the Li{sub 2}TiO{sub 3} single crystals was evaluated using hot-disk method. A single-crystal X-ray diffraction study confirmed the monoclinic Li{sub 2}SnO{sub 3}-type structure, space group C2/c and the lattice parameters of a = 5.0623(5) A, b = 8.7876(9) A, c = 9.7533(15) A, {beta} = 100.212(11) deg., and V = 427.01(9) A{sup 3}. The crystal structure was refined to the conventional values of R = 2.4% and wR=3.3% for 2187 independent observed reflections. The cationic arrangement of (LiTi{sub 2}) layers in Li{sub 2}TiO{sub 3} was precisely revealed by the structure analysis.

36 MATERIALS SCIENCE↗

Crystal growth and characterization of CuI single crystals by solvent evaporation technique

Cuprous iodide (CuI) crystals are grown by slow evaporation technique in three different solvents. Large CuI single crystals with dimensions of 7.5 mm x 5 mm x 3 mm are obtained in pure acetonitrile solvent at 40 {sup o}C. The as-grown crystals are analyzed by X-ray diffraction, energy-dispersive X-ray analysis, differential scanning calorimetry, current-voltage characteristic and photoluminescence spectrum. The results show that the CuI crystal has the zinc-blende structure with no secondary phase. The elemental Cu/I ratio is 1.09:1. The melting point of the crystal is 875 K and two phase transitions occur from room temperature to its melting point. The electrical conductivity of CuI platelet crystal is in the range of 1.11-2.38 {Omega}{sup -1} cm{sup -1}. Under ultraviolet excitation, the CuI crystals exhibit three emission bands with peak positions at 426, 529 and 671 nm. The nature of the luminescence is discussed.

36 MATERIALS SCIENCE↗

Preparation of polymer/LDH nanocomposite by UV-initiated photopolymerization of acrylate through photoinitiator-modified LDH precursor

Graphical abstract: This is the HR-TEM micrograph of UV cured nanocomposite at 5 wt% LDH-2959 loading for a-5 sample. The dark lines are the intersections of LDH platelets. It can be seen that samples a-5 dispersed in the polymer matrix and lost the ordered stacking-structure and show the completely exfoliation after UV curing. This can be explained by the fact that the sample a-5 only containing LDH-2959 exhibited a relative lower photopolymerization rate, which was propitious to further expand the LDH intergallery to form the exfoliated structure. Research highlights: {yields} The UV cured polymer/LDH nanocomposites were prepared through the photopolymerization initiated by the photoinitiator-modified LDH precursor, LDH-2959. {yields} The exfoliated UV cured nanocomposites were achieved in the presence of LDH-2959 only. However, the UV cured nanocomposites prepared using both LDH-2959 and Irgacure 2959 showed the intercalated structure. {yields} Compared with the pure polymer, the exfoliated polymer/LDH nanocomposite showed remarkable enhanced thermal stability and mechanical properties because of their well dispersion in the polymer matrix. -- Abstract: The exfoliated polymer/layered double hydroxide (LDH) nanocomposite by UV-initiated photopolymerization of acrylate systems through an Irgacure 2959-modified LDH precursor (LDH-2959) as a photoinitiator complex was prepared. The LDH-2959 was obtained by the esterification of 2-hydroxy-4'-(2-hydroxyethoxy)-2-methylpropiophenone (Irgacure 2959) with thioglycolic acid, following by the addition reaction with 3-(2,3-epoxypropoxy)propyltrimethoxysilane (KH-560), finally intercalation into the sodium dodecyl sulfate-modified LDH. For comparison, the intercalated polymer/LDH nanocomposite was obtained with additive Irgacure 2959 addition. From the X-ray diffraction (XRD) measurements and HR-TEM observations, the LDH lost the ordered stacking-structure and well dispersed in the polymer matrix at 5 wt% LDH-2959 loading. The glass transition temperature of UV-cured exfoliated nanocomposites increased to 64 {sup o}C from 55 {sup o}C of pure polymer without LDH addition. The tensile strength was improved from 10.1 MPa to 25.2 MPa, as well the Persoz hardness enhanced greatly, while the elongation at break remained an acceptable level.

36 MATERIALS SCIENCE↗

Controlled fabrication of SrMoO{sub 4} hierarchical nanosheets in a surfactant-assisted nonaqueous system

Research highlights: {yields} An imitated nonaqueous microemulsion system was developed. {yields} Various hierarchical architectures of SrMoO{sub 4} nanosheets were fabricated. {yields} The solvent, surfactant, reaction temperature and reaction time were important. {yields} The products emit a strong blue (474 nm) and weak green (573 nm) luminescence. -- Abstract: Various hierarchical architectures of SrMoO{sub 4} nanosheets (thickness of 8-9 nm) have been successfully prepared in nonaqueous system by a surfactant-assisted solvothermal method. X-ray powder diffraction, scanning electron microscopy and transmission electron microscopy were employed to study the crystal structure and morphologies of the products. Experiments showed that the solvent, surfactant, reaction temperature and reaction time were crucial for the oriented aggregation of the SrMoO{sub 4} nanosheets. Morphological control of these parameters resulted in platelet, column, interlaced multilayer and nest of nanosheets. A possible growth mechanism for these hierarchical architectures has also been proposed according to the morphological evolution with the reaction time. The optical properties of the products were also examined by means of photoluminescence and excitation spectroscopy. Photoluminescence studies revealed that these SrMoO{sub 4} nanocrystals exhibited a greatly strong blue emission under 325-nm excitation with different intensities but centered at the same position of 474 nm.

36 MATERIALS SCIENCE↗

Electrodeposited ZnO films with high UV emission properties

Highlights: {yields} Electrodeposition of ZnO from nitrate baths is investigated. {yields} The influence of process parameters on morphological and optical properties is studied. {yields} Experimental conditions to fabricate ZnO films with high UV emission were found. -- Abstract: We report here our results in the preparation of ZnO films with high UV band to band characteristic luminescence emission by potentiostatic electrodeposition. Zinc nitrate aqueous baths with different concentration and additives were employed for the preparation of the films on platinum substrates. We focused our research in determining how the electrodeposition bath composition, i.e. zinc nitrate concentration and addition of KCl or polyvinyl pyrolidone and applied overpotential influence the morphological and optical properties of the oxide films. Scanning electron microscopy was employed for characterizing the films in terms of morphology. Optical reflection, photoluminescence spectroscopy and cathodoluminescence were used for determining the optical characteristics of the samples. The morphology of the deposit varies from hexagonal prisms to platelets as a function of the deposition rate. This experimental parameter also influences the luminescence properties. We found that at low deposition rates high UV luminescent material is obtained.

36 MATERIALS SCIENCE↗

Structural and magnetic properties of conventional and microwave treated Ni-Zr doped barium strontium hexaferrite

Highlights: Black-Right-Pointing-Pointer Saturation magnetization increases whereas the coercivity decreases. Black-Right-Pointing-Pointer The transition from hard phase to soft phase. Black-Right-Pointing-Pointer Therefore, it is used for high-density magnetic recording applications. -- Abstract: M-type hexaferrites of component B{sub 0.5}Sr{sub 0.5}Fe{sub 12-2x}Ni{sub x}Zr{sub x}O{sub 19} were investigated. The XRD patterns show single phase of the magnetoplumbite barium strontium ferrite and no other phases were present. Significant increase in line broadening of the XRD patterns was observed indicating a decrease of grain size. The samples exhibit well defined crystallization; all of them are hexagonal platelet grains. As the substitution level increased x = 0.2-0.8 mol%, the grains are agglomerated and the average diameter increased. The H{sub c} decreases remarkably with increasing Ni and Zr ions content. It was found that the particle size could be effectively decreased and coercivity H{sub c} could easily be controlled by varying the concentration (x) without significantly decreasing saturation magnetization. In particular, Ba{sub 0.5}Sr{sub 0.5}Fe{sub 12-2x}Ni{sub x}Zr{sub x}O{sub 19} with x = 0.2, 0.4, 0.6, 0.8 mol% has suitable magnetic characteristics with particle size small enough for high-density magnetic recording applications.

36 MATERIALS SCIENCE↗

Existence of a solid solution from brucite to {beta}-Co(OH){sub 2}

Highlights: Black-Right-Pointing-Pointer A solid solution exist between Mg(OH){sub 2} and {beta}-Co(OH){sub 2}. Black-Right-Pointing-Pointer Synthesis has been performed through an easy and fast coprecipitation route. Black-Right-Pointing-Pointer No long range-ordering of the cations occurs. -- Abstract: This study shows that between brucite (Mg(OH){sub 2}) and {beta}-Co(OH){sub 2}, all the compositions are possible. The solid solution Mg{sub 1-x}Co{sub x}(OH){sub 2} has been synthesized by an easy and fast coprecipitation route and characterized by XRD and TEM. Single phase powders have been obtained. The particles exhibit platelets morphology with a size close to one hundred nanometers. XRD analysis shows an evolution of the cell parameters when x increases and demonstrates that no ordering of the cations occurs. However, extra reflections on TEM electron diffraction patterns seem to indicate that local ordering can exist. The compounds issued from this solid solution could be good candidates as precursors in order to obtain Mg-Co mixed oxide with all possible cationic ratios.

36 MATERIALS SCIENCE↗

New synthetic route to Mg–Al–CO{sub 3} layered double hydroxide using magnesite

Highlights: ► The use of magnesite to prepare Mg–Al–CO{sub 3} LDH is novel. ► The result sample is systematically studied. ► Furthermore, the cost of preparing Mg–Al–CO{sub 3} LDH may be reduced through this synthetic route. ► In the synthesis process, there is no CO{sub 2} released. That is significant to environmental protection. - Abstract: A novel synthesis of Mg–Al–CO{sub 3} layered double hydroxide (LDH) through chemical precipitation and hydrothermal methods has been investigated in this paper. The advantages of this method are using magnesite as magnesium source and no CO{sub 2} released in the process of preparation. Mg–Al–CO{sub 3} LDH (ZY) prepared under the optimized condition (the molar ratio of magnesite and Al(NO{sub 3}){sub 3}·9H{sub 2}O was 2.5:1; the aging time and temperature were 16 h and 100 °C, respectively) was characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), thermo-gravimetric and differential thermal analyser (TG–DTA) and scanning electron microscope (SEM). The crystal morphology of the prepared LDH displays platelet-like structure with a hexagonal shape, which is agreed with the LDH produced by industrial chemicals. Through elemental analysis and inductively coupled plasma-atomic emission spectrometry (ICP-AES), the chemical formula of ZY is determined as Mg{sub 0.70}Al{sub 0.30}(OH){sub 2}(CO{sub 3}){sub 0.15}·0.6H{sub 2}O.

36 MATERIALS SCIENCE↗

One-pot fabrication and characterization of graphene/PMMA composite flexible films

Highlights: • Investigated the fabrication and characterization of conducting flexible films based on graphene/PMMA polymer composite. • Graphene/PMMA flexible films were fabricated by one-pot alternate stirring sonication (OPASS) process. • Electrical response of the fabricated flexible films were studied and exhibited an electrical conductivity of 44.92 S/m and 0.10 S/m with 50 wt% and 10 wt% concentrations, respectively. • Reinforcing polymers with graphite platelets will amend their surface toughness, modulus and barrier properties, suitable for commercial applications. - Abstract: The present work investigates fabrication and characterization of graphene/ poly (methyl methacrylate) (PMMA) composite flexible films. Graphene/PMMA flexible films were fabricated by one-pot alternate stirring sonication (OPASS) process. The method relies on the alternate high speed stirring and ultrasonication of graphite and its blending with PMMA without any sufactant assistance. A comparative study of the nanocomposite solution was carried out with the composite solution prepared by conventional (CL) method. The transformation of micro-sized graphite particles to nano-sized layers of graphite or few layer graphene was characterized by various analytical techniques. The electrical response of the fabricated flexible films were studied and exhibited an electrical conductivity of 44.92 S/m and 0.10 S/m with 50 wt% and 10 wt% concentrations, respectively. Thus, the fabricated flexible films could have excellent surface toughness, modulus and barrier properties, which make them a suitable candidate for commercial flexible electronic and wearable sensor applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

An inorganic coating and flexible regulating in situ of stent endothelialization by the controllable ion releasing

Highlights: • The Cu/Ti film with regulating the various responses of ECs and SMCs has been prepared. • The hemocompatibility could be adjusted via the ratio of Cu/Ti. • The volume and velocity of copper ion released from film was designed via the preparation processing. - Abstract: A facile approach to fabricate an inorganic coating with favorable blood compatibility and accelerating endothelialization is reported. The inorganic coating with various ratios of Cu and Ti atom are prepared on 316 L stainless steel by physical vapor deposition method. The phase composition and structure as well as the element concentration of the coating are investigated by X-ray diffraction and X-photoelectron energy spectrum. The hemolysis ratio, clotting time and platelet adhesion are utilized to characterize the materials’ hemocompatibility, the copper ion releasing was also investigated via immersing test. The result indicates that copper-titanium coating show good compatibility; however, as the ratio of Cu to Ti increases, the hemolysis ratio also increases. The endothelialization degree was accelerated owing to maintain less than 7.0 μg/ml of Cu{sup 2+} concentrate, and endothelial cells proliferate more readily than smooth muscle cells. The results demonstrate that this degradable copper-containing coating is suitable as a new surface modification for vascular stents.

36 MATERIALS SCIENCE↗