Development of microwave NDT inspection techniques for large solid propellant rocket motors Final report
Microwave nondestructive testing techniques for large solid propellant rocket engines
Eckert, T. E.↗
SEARCH · Search NASA
Results for “PROPELLANT TESTING”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Evaluation of cryogenic system test options for the OTV on-orbit propellant depot
Future space missions to geosynchronous, lunar, and planetary orbits will require an orbital depot for stockpiling propellants. This depot will provide long-term storage of cryogens, requiring new technologies for fluid management in microgravity and further development of thermal management technologies for minimization of cryogen boiloff. Preliminary evaluations have been made to define a test program approach for reducing technical risk through verifying performance models and building a base of engineering data for depot design. A number of testing options were defined and evaluated, leading to selection of ground testing combined with an orbital systems test. Ground testing is inadequate because of critical microgravity concerns; extending testing aboard the Space Station was eliminated because the data would not be available soon enough to benefit the propellant depot design. The orbital test would either be a short-term test carried out in the cargo bay of the Space Shuttle Orbiter using a nonhazardous cryogen or a longer term test carried out with hydrogen aboard a free-flying experiment orbited with an expendable launch vehicle.
Schuster, John R.↗
Investigation of the NACA 4-(3)(8)-045 Two-blade Propellers at Forward Mach Numbers to 0.725 to Determine the Effects of Compressibility and Solidity on Performance
As part of a general investigation of propellers at high forward speeds, tests of two 2-blade propellers having the NACA 4-(3)(8)-03 and NACA 4-(3)(8)-45 blade designs have been made in the Langley 8-foot high-speed tunnel through a range of blade angle from 20 degrees to 60 degrees for forward Mach numbers from 0.165 to 0.725 to establish in detail the changes in propeller characteristics due to compressibility effects. These propellers differed primarily only in blade solidity, one propeller having 50 percent and more solidity than the other. Serious losses in propeller efficiency were found as the propeller tip Mach number exceeded 0.91, irrespective of forward speed or blade angle. The magnitude of the efficiency losses varied from 9 percent to 22 percent per 0.1 increase in tip Mach number above the critical value. The range of advance ratio for peak efficiency decreased markedly with increase of forward speed. The general form of the changes in thrust and power coefficients was found to be similar to the changes in airfoil lift coefficient with changes in Mach number. Efficiency losses due to compressibility effects decreased with increase of blade width. The results indicated that the high level of propeller efficiency obtained at low speeds could be maintained to forward sea-level speeds exceeding 500 miles per hour.
Stack, John↗
Extreme-Temperature Carbon- and Ceramic-Matrix Composite Nozzle Extensions for Liquid Rocket Engines
The United States (US) National Aeronautics and Space Administration (NASA) and its US industry partners are developing extreme-temperature composite nozzle extensions for a variety of cryogenic liquid rocket engine propulsion systems. Applications under consideration at the NASA Marshall Space Flight Center (MSFC) include launch vehicle (upper stage), in-space, and lunar lander descent/ascent propulsion systems. Composite material systems of interest include carbon-carbon (C-C) and carbon/silicon-carbide (C-SiC) composites, as well as modified versions of such composites (coatings, mixed matrices, oxidation inhibitors, etc.). Missions addressed include access to low Earth orbit, the lunar surface, and more distant destinations. Cryogenic upper-stage and in-space liquid rocket engines are optimized for performance through the use of high area ratio nozzles to fully expand combustion gases to low exit pressures, increasing exhaust velocities. As a result of the large size of such nozzles, and the related engine performance requirements, composite nozzle extensions are being considered to reduce mass impacts. Currently, metallic and foreign composite nozzle extensions used on the Atlas V, Delta IV, Falcon 9, and Ariane 5 launch vehicles represent the state-of-the-art. Such extensions are limited to use at or slightly above 2000°F (1093°C). Materials under development by MSFC and its industry partners have the potential to operate at temperatures up to (or above) 4250°F (2343°C). Marshall Space Flight Center efforts are aimed at (a) further developing the technology and databases needed to enable the use of composite nozzle extensions on cryogenic liquid rocket engines, (b) developing and demonstrating low-cost capabilities for testing and qualifying such nozzle extensions, and (c) advancing the US domestic supply chain for nozzle extensions. Through the Small Business Innovation Research (SBIR) and Small Business Technology Transfer (STTR) Programs, low-level internal MSFC research projects, and teaming arrangements with domestic industry partners, composite material design, development, hot-fire test, and evaluation efforts are progressing. Hot- fire engine tests of subscale hardware have been conducted using oxygen/hydrogen (LOX/H2), oxygen/methane (LOX/CH4), and oxygen/kerosene (LOX/RP-1) propellants. These engine tests at MSFC have enabled the evaluation of both heritage and state-of-the-art material systems, demonstrating the initial capabilities of the extreme temperature materials and their fabrication methods. Recent, ongoing, and potential future work supporting cryogenic propulsion systems development will be presented. The composite nozzle extension technology and test capabilities being developed are intended to support both NASA and US Department of Defense requirements, as well as those of the broader Commercial Space industry.
Valentine, Peter G.↗
The Effect on Stability and Control of a Pusher Propeller Behind Conventional Tail Surfaces as Determined by Tests of a Powered Model in the Free-flight Tunnel
Explore the source record for details and available documents.
PROPELLERS, PUSHER VS TRACTOR↗
Determination of the level flight performance of propeller-driven aircraft
A flight test method to determine the level flight performance of propeller driven aircraft is reported that measures the amount of power it takes to overcome a known increment of added drag to maintain steady state flight conditions to determine overall drag and propeller efficiency of a general aviation aircraft.
Cross, E. J.↗
Propfan installation aerodynamics of a supercritical swept wing transport configuration
A semispan model with a powered propeller has been tested to provide data on the installation drag penalty of advanced propfan-powered transports designed to cruise at a Mach number of 0.8. These tests, conducted in 14-foot and 11-foot transonic wind tunnels, are a part of a NASA program to develop efficient, high-speed propellers for more fuel-efficient commercial transports for the 1990s and beyond. The model is instrumented for measuring propeller forces, wing/nacelle forces and moments, and pressure distributions over the wing and nacelle. The body in these tests was nonmetric, being connected to the wing by an RTV seal at the wing/body juncture. Tests were run at angles of attack from -3 to +5 deg over the Mach number range 0.6 to 0.85 at a Reynolds number of about 9,000,000. Results of these tests indicate that the nacelle interference drag can be quite large relative to an uninstalled nacelle. However, the losses due to the nacelle were reduced to acceptable levels by changes to the wing leading edge and nacelle intersection. The propeller slipstream causes substantial changes in the wing span load distribution indicating that twist modifications are needed to recover a more favorable span load distribution.
Smith, R. C.↗
The scaling of the threshold conditions for solid propellant erosive burning
Rocket test firings were performed to measure the transition length threshold conditions while systematically varying various rocket motor parameters. These include the crossflow velocity, the chamber pressure, the propellant nonerosive burning rate, the propellant surface roughness, and the motor port diameter. The erosive burning trends with varying propellant burning rate, motor chamber pressure, and mass flow rate are consistent with published results.
Strand, L. D.↗
Rift Radiation Effects Program, Irradiation No. 9, Monomethyl Hydrazine
Radiation testing monomethyl hydrazine propellant for rift project
REACTOR IN-FLIGHT TEST /RIFT/ PROJECT↗
ALS engine propellant effector system
This report summarizes analysis, design, and experimental testing done on the propellant effector (valve plus electromechanical actuator) for the Advanced Launch System (ALS) main engine.
Faulkner, Colin↗
Test Results for a Non-toxic, Dual Thrust Reaction Control Engine
A non-toxic, dual thrust reaction control engine (RCE) was successfully tested over a broad range of operating conditions at the Aerojet Sacramento facility. The RCE utilized LOX/Ethanol propellants; and was tested in steady state and pulsing modes at 25-lbf thrust (vernier) and at 870-lbf thrust (primary). Steady state vernier tests vaned chamber pressure (Pc) from 0.78 to 5.96 psia, and mixture ratio (MR) from 0.73 to 1.82, while primary steady state tests vaned Pc from 103 to 179 psia and MR from 1.33 to 1.76. Pulsing tests explored EPW from 0.080 to 10 seconds and DC from 5 to 50 percent at both thrust levels. Vernier testing accumulated a total of 6,670 seconds of firing time, and 7,215 pulses, and primary testing accumulated a total of 2,060 seconds of firing time and 3,646 pulses.
Robinson, Philip J.↗
Wind tunnel results of advanced high speed propellers in the takeoff, climb and landing operating regimes
Low speed wind tunnel performance tests of two advanced propellers were completed. The 62.2 cm diameter adjustable pitch models were tested at Mach numbers typical of takeoff, initial climbout, and landing speeds in the 10 by 10 ft Supersonic Wind Tunnel. Both models had eight blades and a cruise design point operating condition of 0.80 Mach number, 10.668 km S.A. altitude, 243.8 m/s tip speed and a high power loading of 301 kW sq m. No adverse or unusual low speed operating conditions were found during the test with either the straight blade SR-2 or the 45 deg swept SR-3 propellers. The 45 deg swept propeller efficiency exceeded the straight blade efficiency by 4 to 5%. Typical net efficiencies of the straight and 45 deg swept propeller at a Mach 0.20 takeoff condition were 50.2 and 54.9% respectively. At a Mach 0.34 climb condition, the efficiencies were 53.7 and 59.1%. Reverse thrust data indicates that these propellers are capable of producing more reverse thrust at Mach 0.20 than a high bypass turbofan engine at Mach 0.20.
Stefko, G. L.↗
Wind tunnel results of advanced high speed propellers in the takeoff, climb, and landing operating regimes
Low speed wind tunnel performance tests of two advanced propellers were completed. The 62.2 cm diameter adjustable pitch models were tested at Mach numbers typical of takeoff, initial climbout, and landing speeds in the 10 by 10 ft Supersonic Wind Tunnel. Both models had eight blades and a cruise design point operating condition of 0.80 Mach number, 10.668 km S.A. altitude, 243.8 m/s tip speed and a high power loading of 301 kW sq m. No adverse or unusual low speed operating conditions were found during the test with either the straight blade SR-2 or the 45 deg swept SR-3 propellers. The 45 deg swept propeller efficiency exceeded the straight blade efficiency by 4 to 5 percent. Typical net efficiencies of the straight and 45 deg swept propeller at a Mach 0.20 takeoff condition were 50.2 and 54.9 percent respectively. At a Mach 0.34 climb condition, the efficiencies were 53.7 and 59.1 percent. Reverse thrust data indicates that these propellers are capable of producing more reverse thrust at Mach 0.20 than a high bypass turbofan engine at Mach 0.20.
Stefko, G. L.↗
Ignition propagation and heat effects of propellant chips embedded in castable inhibitor using a laser flux test bomb
A castable inhibitor is applied to the aft face of the Space Shuttle Redesigned Solid Rocket Motor (RSRM) forward segment propellant grain to control propellant surface burn area. During fabrication, the propellant surface is trimmed prior to the inhibitor application. This produces a potential for small propellant chips to remain undetected on the propellant surface and contaminate the inhibitor during application. The concern was that undetected propellant chips in the inhibitor might provide a fuse path for premature propellant ignition underneath the inhibitor. To evaluate the fuse path potential, testing was performed on inhibitor samples with embedded propellant. The internal motor environment was simulated with a calibrated CO2 laser beam directed onto a sample which was placed in a 4100 kPa (600 psi) nitrogen pressurized bomb (laser bomb). The testing showed definitive results pertaining to fuse path formation. Embedded propellant chips did not autoignite until the receding heat affected inhibitor surface reached, or passed, the propellant chip. Samples with embedded propellant chips in alignment did not propagate ignition from one chip to another with separation distances as small as 0.010 cm(0.004 inc) and some as little as 0.0051 cm (0.002 in). Propellant chips with volumes approximately less than 0.025 cu cm (0.0015 cu in) (which did not propagate ignition) did not increase the inhibitor material decomposition depth more than the resulting void cavity of the burned out propellant chip. In addition, the depth of this void cavity did not increase until it was overtaken by the surrounding material decomposition depth. This was due, in part, to the retention of the protective inhibitor char layer. Samples with embedded propellant strings, whose thicknesses were below 0.023 cm (0.009 in), did not propagate ignition. Propellant string thicknesses above 0.038 cm (0.015 in) did propagate ignition. Test sample char and heat affected layer measurements and observations compared well with those from the Space Shuttle Solid Rocket Motor (SRM) Technical Evaluation Motor no. 9(TEM-9).
Bolton, Douglas E., Jr.↗
Electrothermal thruster diagnostics. Volume 1: Executive summary
A flight-qualified electrothermal thruster demonstrated its adaptability to a variety of propellants. Originally qualified for operation with hydrazine propellant, it was operated with nitrogen, hydrogen, and ammonia propellants, demonstrating 73, 61, and 52 percent overall efficiency with these propellants, respectively, when tested over a wide range of operating conditions. By introducing a preheater to admit hot, rather than cold, propellant inlet gases to the thruster's augmentation heat exchanger, delivered specific impulse closer to theoretical performance limits should be achieved.
Zafran, S.↗
Electrothermal thruster diagnostics
A flight-qualified electrothermal thruster demonstrated its adaptability to a variety of propellants. Originally qualified for operation with hydrazine propellant, it was operated with nitrogen, hydrogen, and ammonia propellants, demonstrating 73, 61, and 52 percent overall efficiency with these propellants, respectively, when tested over a wide range of operating conditions. By introducing a preheater to admit hot, rather than cold, propellant inlet gases to the thruster's augmentation heat exchanger, delivered specific impulse closer to theoretical performance limits should be achieved.
Zafran, S.↗
Resistojet operation with various propellants
A flight-qualified electrothermal thruster demonstrated its adaptability to a variety of propellants. Originally qualified for operation with hydrazine propellant, it was operated with nitrogen, hydrogen, and ammonia propellants, demonstrating 73, 61, and 52 percent overall efficiency with these propellants, respectively, when tested over a wide range of operating conditions. By introducing a preheater to admit hot, rather than cold, propellant inlet gases to the thruster's augmentation heat exchanger, delivered specific impulse closer to theoretical performance limits should be achieved.
Zafran, S.↗
Flight tests of a rotating cylinder flap on a North American Rockwell YOV-10 aircraft
Flight tests were conducted of a twin engine airplane modified to a STOL configuration with rotating cylinder flaps and interconnected propellers. The flight tests included verification of the functional operation of the rotating cylinder flap system and the determination of the low speed flying qualities and performance characteristics with emphasis on approach and landing.
Cichy, D. R.↗