Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reaction Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

The effect of normal atmospheric variability on Space Shuttle Orbiter entry performance

The Space Shuttle Orbiter is controlled during entry by a combination of aerodynamic surfaces composed of elevons, a body flap, and a rudder that flares as a speedbrake, and a reaction control system that uses 16 small rocket thrusters. To determine the effects of realistic atmospheric density variations on reentry, a series of Monte Carlo trajectories were generated for each season. The performance parameters analyzed include maximum hinge moments experienced by the aerodynamic control surfaces, the maximum deflections experienced by the aerodynamic control surfaces, a range of angle-of-sideslip values, maximum dynamic pressure, maximum stagnation point heat rate, and state conditions at touchdown. The results of the investigation indicate that the Orbiter guidance and control systems could tolerate atmospheric variability without failures in the control system hardware.

Powell, R. W.↗
NASA NTRS1982

Bipulsating Technique for Silicon Production

Method controls reaction temperature and rate of reaction of sodium and silicon tetrafluoride by alternately adding measured amounts of reactants. Technique used in large reactor, where heat dissipation becomes serious problem, to control reactor temperatures. Highly efficient method, which would utilize almost 100 percent of raw materials.

Sanjurjo, A.↗
NASA NTRS2015

Post-Flight Analysis of the Guidance, Navigation, and Control Performance During Orion Exploration Flight Test 1

The first test flight of the Orion Multi-Purpose Crew Vehicle presented additional challenges for guidance, navigation and control as compared to a typical re-entry from the International Space Station or other Low Earth Orbit. An elevated re-entry velocity and steeper flight path angle were chosen to achieve aero-thermal flight test objectives. New IMU's, a GPS receiver, and baro altimeters were flight qualified to provide the redundant navigation needed for human space flight. The guidance and control systems must manage the vehicle lift vector in order to deliver the vehicle to a precision, coastal, water landing, while operating within aerodynamic load, reaction control system, and propellant constraints. Extensive pre-flight six degree-of-freedom analysis was performed that showed mission success for the nominal mission as well as in the presence of sensor and effector failures. Post-flight reconstruction analysis of the test flight is presented in this paper to show whether that all performance metrics were met and establish how well the pre-flight analysis predicted the in-flight performance.

Barth, Andrew↗
NASA NTRSDate not supplied

Reflectivity Control Device (RCD) Momentum Management for Solar Cruiser and Future Solar Sail Missions

Solar sails provide propulsion from solar photonic pressure without the need for propellant. This advantage can be reduced or eliminated if propellant is required for attitude control. The current state of the art for solar sail attitude control is that of the solar sail mission Near Earth Asteroid Scout, which employs an Adjustable Mass Translator for pitch and yaw momentum management of reaction wheels, but must use a cold gas Reaction Control System for roll axis momentum management. It is highly desirable for solar sails to use an attitude control system that does not include propellant, so here we present a novel method of managing momentum on the roll axis. For the upcoming Solar Cruiser solar sail mission, for roll axis momentum management we plan to use Reflectivity Control Devices (RCDs), thin-film Polyimide Liquid Crystal Devices that are capable of changing optical properties on command, thus affording the opportunity to provide “photonic only” control if placed appropriately on the surface of the sail. RCD design for roll momentum management is multifaceted, and must include performance (degree of change in optical properties), RCD array size, locations of clusters on the sail, orientation with respect to the sail plane, and orientation out of the sail plane. Here we provide an explanation of the basic technology, optimal orientation, sizing, and location of RCDs, results of trade studies for Solar Cruiser, lessons learned from Solar Cruiser, and scalability for future solar sail missions. RCDs will dramatically improve the performance of the Solar Cruiser Momentum Management System compared to that of NEA Scout and will continue to benefit other future solar sail missions.

Daniel Tyler↗
NASA NTRSDate not supplied

Reflectivity Control Device (RCD) Roll Momentum Management for Solar Cruiser and Future Solar Sail Missions

Solar sails provide propulsion from solar photonic pressure without the need for propellant. This advantage can be reduced or eliminated if propellant is required for attitude control. The current state of the art for solar sail attitude control is that of the solar sail mission Near Earth Asteroid Scout, which employs an Adjustable Mass Translator for pitch and yaw momentum management of reaction wheels, but must use a cold gas Reaction Control System for roll axis momentum management. It is highly desirable for solar sails to use an attitude control system that does not include propellant, so here we present a novel method of managing momentum on the roll axis. For the upcoming Solar Cruiser solar sail mission, for roll axis momentum management we plan to use Reflectivity Control Devices (RCDs), thin-film Polyimide Liquid Crystal Devices that are capable of changing optical properties on command, thus affording the opportunity to provide “photonic only” control if placed appropriately on the surface of the sail. RCD design for roll momentum management is multifaceted, and must include performance (degree of change in optical properties), RCD array size, locations of clusters on the sail, orientation with respect to the sail plane, and orientation out of the sail plane. Here we provide an explanation of the basic technology, optimal orientation, sizing, and location of RCDs, results of trade studies for Solar Cruiser, lessons learned from Solar Cruiser, and scalability for future solar sail missions. RCDs will dramatically improve the performance of the Solar Cruiser Momentum Management System compared to that of NEA Scout and will continue to benefit other future solar sail missions.

Daniel Tyler↗
NASA NTRS1979

An overview of current Navy programs to develop thrust augmenting ejectors

The primary objective of Navy sponsored research in thrust augmentation is the development of an improved augmenter for V/STOL application. In support of this goal, a data base is being established to provide an accurate prediction capability for use in ejector design. A general technology development of ejectors and associated effects presently is split into the more specific areas of lift and control, since thrust augmenting ejectors may be suitable for both. Research areas examined include advanced diffuser and end wall design; advanced primary nozzles; analytic studies; augmenting reaction controls; and nozzle design.

Green, K. A.↗
NASA NTRS1975

Effects of Control Hysteresis on the Space Shuttle Orbiter's Entry

There are six degree-of-freedom simulations of the space shuttle orbiter entry with aerodynamic control hysteresis conducted on the NASA Langley Research Center interactive simulator known as the Automatic Reentry Flight Dynamics Simulator. These were performed to determine if the presence of aerodynamic control hysteresis would endanger the mission, either by making the vehicle unable to maintain proper attitude for a safe entry, or by increasing the amount of the reaction control system's fuel consumption beyond that carried.

Powell, R. W.↗
NASA NTRS1982

Shuttle entry performance and stability and control derivatives extraction from flight measurement data

Flight data taken from three Shuttle Space Transportation System flights (STS-1, 2, and 3) during entry are analyzed to determine the shuttle performance and aerodynamic characteristics. Correlations of the performance coefficients and the stability and control derivatives with preflight predictions are presented over the hypersonic speed range from Mach 2 to 25. In addition, an evaluation of the effectiveness of the onboard Reaction Control System (RCS) is given and an effort is made to independently quantify the combined impingement and flow-field interaction effects on the spacecraft rolling moment. Comparisons of stability and control derivatives extracted for the same flight conditions, but using data from different onboard sensors are also made. Results obtained using the same flight data, but different computer software are also shown.

Compton, H. R.↗
NASA NTRS1989

Detection of potential space station control/structure interaction with CO-ST-IN

The NASA Lewis Research Center is concerned with the potential of interaction between space station controllers and the solar PV array structures. The models required to handle this problem are very large, and automated methods were developed for the transfer of data between structural dynamic and control system analysis software. These methods emphasize the need to achieve accurate coupled analysis results while using as small a model as possible. Specific tools which help the analyst in this regard include modal order techniques, the use of mode acceleration to calculate internal loads and stresses and the transfer of Craig-Bampton components to reduce problems associated with modal sufficiency. These techniques were applied to a space station model with 366 modes below 1 Hz. Attitude control, and alpha and beta joint control were simulated. The inclusion of alpha and beta joint controllers is important when examining overall space station dynamics. An initial choice of control parameters does indicate a potential for control/structure interaction during reboost. As expected this is exacerbated by increasing the rate gain and decreasing the hysteresis of the reaction control system (RCS) in order to improve rigid body performance.

Carney, Kelly↗
NASA NTRS2005

Analysis of Thrust Vectoring Capabilities for the Jupiter Icy Moons Orbiter

A strategy to mitigate the impact of the trajectory design of the Jupiter Icy Moons Orbiter (JIMO) on the attitude control design is described in this paper. This paper shows how the thrust vectoring control torques, i.e. the torques required to steer the vehicle, depend on various parameters (thrust magnitude, thrust pod articulation angles, and thrust moment arms). Rather than using the entire reaction control system (RCS) system to steer the spacecraft, we investigate the potential utilization of only thrust vectoring of the main ion engines for the required attitude control to follow the representative trajectory. This study has identified some segments of the representative trajectory where the required control torque may exceed the designed ion engine capability, and how the proposed mitigation strategy succeeds in reducing the attitude control torques to within the existing capability.

low thrust↗
NASA NTRS1973

Flight-determined stability and control characteristics of the M2-F3 lifting body vehicle

Flight data were obtained over a Mach number range from 0.4 to 1.55 and an angle-of-attack range from -2 deg to 16 deg. Lateral-directional and longitudinal derivatives, reaction control rocket effectiveness, and longitudinal trim information obtained from flight data and wind-tunnel predictions are compared. The effects of power, configuration change, and speed brake are discussed.

Sim, A. G.↗
NASA NTRS1993

Space Station/Orbiter berthing dynamics during an assembly flight

A large-angle, multi-body, dynamic modeling capability was developed to help validate numerical simulations of the dynamic motion and control forces which occur while berthing Space Station Freedom to the Shuttle Orbiter during early assembly flights. The paper describes the dynamics and control of the station, the attached Shuttle Remote Manipulator System, and the Orbiter during a maneuver from a gravity-gradient attitude to a torque equilibrium attitude using the station reaction control jets. The influence of the elastic behavior of the station and of the remote manipulator system on the attitude control of the station/Orbiter system during the maneuver is investigated. The flexibility of the station and the arm had only a minor influence on the attitude control of the system during the maneuver.

Cooper, Paul A.↗
DOE OSTI2022

Nanopore facilitated monohydrocalcitic amorphous calcium carbonate precipitation

Predicting the precipitation of solids is important in both natural systems and subsurface energy applications. The factors controlling reaction mechanisms, phase selection and conversion between phases are particularly important. In this contribution the precipitation and growth of an amorphous calcium carbonate species from flowing aqueous solution in a nanoporous controlled pore glass is followed in situ with differential X-ray pair distribution function analysis. It is discovered that the local atomic structure of this phase indicates monohydrocalcite-like pair–pair correlations, yet is functionally amorphous because it lacks long-range structure. The unexpected occurrence of synthetic proto-monohydrocalcite amorphous calcium carbonate, precipitated from a solution undersaturated with respect to published solubilities, suggests that nanopore confinement facilitates formation of an amorphous phase at the expense of more favorable crystalline ones. Finally, this result illustrates that confinement and interface effects are physical factors exerting control on mineral nucleation behavior in natural and geological systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1984

Rapid single-axis torque-bounded slewing of SCOLE configuration

The first general research objective was to address control design challenges of the Spacecraft Control Laboratory Experiment (SCOLE) via the two stage approach: (1) slew the whole as if it were a rigid body about one Space Shuttle body axis each time using the onboard Reaction Control System (RCS) thrusters; and (2) damp out excited vibrations. The second objective was to examine the feasibility of applying the approach to shuttle-attached flexible space structures. The following was accomplished: (1) a standard bang-bang control technique was adapted; (2) a slew rate limit was imposed in the design; and (3) slew acceleration deviation was defined as the index of slew performance degradation.

Lin, Jiguan Gene↗
NASA NTRS1972

Apollo guidance, navigation and control: Guidance system operations plan for manned CM earth orbital and lunar missions using Program COLOSSUS 3. Section 3: Digital autopilots (revision 14)

Digital autopilots for the manned command module earth orbital and lunar missions using program COLOSSUS 3 are discussed. Subjects presented are: (1) reaction control system digital autopilot, (2) thrust vector control autopilot, (3) entry autopilot and mission control programs, (4) takeover of Saturn steering, and (5) coasting flight attitude maneuver routine.

Source record↗
NASA NTRS1974

Oxidative vaporization kinetics of chromium (III) oxide in oxygen from 1270 to 1570 K

Rates of oxidative vaporization of Cr2O3 on preoxidized resistively heated chromium were determined in flowing oxygen at 0.115 torr for temperatures from 1270 to 1570 K. Reaction controlled rates were obtained from experimental rates by a gold calibration technique. These rates were shown to agree with those predicted by thermochemical analysis. The activation energy obtained for the oxidative vaporation reaction corresponded numerically with the thermochemical enthalpy of the reaction. A theoretical equation is given for calculating the rate from thermodynamic data by using boundary layer theory.

Stearns, C. A.↗
NASA NTRS1974

The hard start phenomena in hypergolic engines. Volume 5: RCS engine deformation and destruct tests

Tests were conducted to determine the causes of Apollo Reaction Control (RCS) engine failures. Stainless steel engines constructed for use in the destructive tests are described. The tests conducted during the three phase investigation are discussed. It was determined that the explosive reaction that destroys the RCS engines occurs at the time of engine ignition and is apparently due to either the detonation of the heterogeneous constituents of the rocket engine, consisting primarily of unreacted propellant droplets and vapors, and/or the detonation of explosive materials accumulated on the engine walls from previous pulses. Photographs of the effects of explosions on the simulated RCS engines are provided.

Miron, Y.↗