Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reactor system”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Screening aqueous organic redox couples for spontaneous hydrogen generation on catalysts

Two low-cost redox couples with near neutral or alkaline pH - 7,8-dihydroxyphenazine-2-sulfonic acid (DHPS) and chrome chelated ethylenediaminetetraacetic acid (Cr-EDTA) with ammonia – are identified to generate hydrogen evolution spontaneously on Pt/C catalysts. Cr-EDTA redox couple has two times higher hydrogen evolution rate than that of DHPS, and the charged Cr-EDTA molecules are fully utilized to generate hydrogen gas, while ~ 50% of DHPS molecules are utilized to produce hydrogen spontaneously on Pt/C catalysts. The Cr-EDTA electrolyte enables cost reduction by allowing cheap raw material of Cr and corrosion resistant alloy instead of costly superalloy for catalytic reactor systems. Furthermore, the Cr-EDTA with ammonia as a negolyte for flow batteries was validated to suppress hydrogen evolution side reaction, reach 99% of coulombic efficiency in flow cell operation paired with Fe(CN)6 redox couple near neutral pH.

08 HYDROGEN↗
DOE OSTI2024

Site-specific Design Case Study for Wet Waste Hydrothermal Liquefaction and Biocrude Upgrading to Hydrocarbon Fuels

Hydrothermal liquefaction (HTL) is a thermal process that converts wet biomass to renewable hydrocarbon fuel blendstocks (i.e., renewable naphtha, renewable diesel, and sustainable aviation fuel (SAF)). It can utilize a wide range of pure and blended wet feedstocks, including sewage sludge from water resource recovery facilities (WRRF), food and agriculture wastes, algae, fats, oils and greases (FOG) and blends of dry and wet wastes/feedstocks. Historically, techno-economic analysis (TEA) and annual state of technology (SOT) assessments with standard economic assumptions used by the Bioenergy Technologies Office (BETO) were conducted for the wet waste HTL pathway leveraging experimental data collected from Pacific Northwest National Laboratory’s (PNNL) continuous flow reactor systems. The objective of the SOT assessment has been to guide and track progress of BETO’s HTL research and development (R&D) toward reduced cost and greenhouse gas (GHG) emissions for the pathway. However, gaps exist between BETO’s traditional SOT updates and the needs of key external stakeholders that – if addressed – will accelerate technology adoption. This Business Case Study aims to bridge this gap by providing an updated design, TEA, and LCA based on PNNL’s FY23 R&D with added analyses and information that provide enhanced relevance for stakeholders of the HTL technology. This includes specific siting, regional wet waste resource inventory and transportation cost analyses, fuel market information, sustainable fuel policy impacts, economic metrics of net present value (NPV) and internal rate of return (IRR), greenhouse gas (GHG) emissions analysis, and statistical analysis of cost and technical uncertainties of the HTL plant design. The study focuses on the “Detroit combined statistical area (CSA)” region for siting of a wet waste HTL plant adjacent to the Great Lakes Water Authority (GLWA) facility with guidance from industry participants. Regional resource and siting analyses were conducted to identify feedstock availability, scale, and cost, as well as a beneficial site location. TEA with detailed rigorous capital cost estimation for the specific site application was conducted to evaluate the key economic metrics of most value to industrial partners. These include total capital investment, operating costs, minimum fuel selling price (MFSP) of the biocrude and fuel blendstock, and NPV and internal rate of return IRR with sustainable fuel credits. Life cycle analysis was conducted to evaluate the supply chain greenhouse gas (GHG) emissions for the wet waste HTL process as compared with petroleum derived diesel. This study is also informed by years of R&D and process de-risking learnings and was conducted with a basic engineering HTL plant design and costing that akin to a “first-of-a-kind” plant economics. This differs from our conventional “nth plant ” SOT assessments. Specifically, the HTL process model has been updated with more operationally reliable methods for feed heating and phase separations. Further, we have implemented additional spare equipment for redundancy, a more rigorous installed equipment cost estimation approach, and additional costs associated with feed formatting and delivery, building, piping and site development. An Excel-based cost sheet based on the basic engineering design is also released alongside the report that allows users to conduct customized TEA with their own feed composition and financial assumptions.

09 BIOMASS FUELS↗
DOE OSTI2025

The Effect of Metal Promoters in an Mo-Supported HZSM-5 Catalyst for Microwave-Assisted Methane Dehydroaromatization to Aromatics

Microwave (MW)-assisted methane dehydroaromatization (MDHA) using an Mo-supported HZSM-5 catalyst (Mo/HZ5) can convert methane into value-added aromatic products in modular microwave reactor systems, enabling producers to generate revenue from an otherwise wasted resource. Modifying the local environments of active Mo species with metal promoters potentially regulates the reaction/deactivation pathways and improves the heating properties of the Mo/HZ5 under microwaves. Herein, metal promoters (M), including monovalent K+ and bivalent Co2+ and Ni2+, were incorporated to form M-Mo/HZ5 and their MDHA performance was investigated.

metal promoters↗
DOE OSTI2025

Influence of Mo- and Ga-Supported HZSM-5 Co-Catalyst Configuration in Microwave-Assisted Methane and Ethane Dehydroaromatization

Microwave (MW)-assisted dehydroaromatization (DHA) using an Mo-supported HZSM-5 catalyst (Mo/HZSM-5) enhances the value of natural gas resources by converting stranded or underutilized natural gas into value-added chemicals in modular microwave reactor systems. This approach offers the potential to generate economic value. However, natural gas mixtures often contain multiple components, including ethane (C2H6) and propane (C3H8), which complicate the reaction pathways. Ga-supported HZSM-5 (Ga/HZSM-5) catalysts are generally inactive toward CH4 but exhibit higher activity toward C2H6 and C3H8. Therefore, investigating the combination of Mo/HZSM-5 and Ga/HZSM-5 in various catalyst bed configurations is essential. This study explores different co-catalyst bed configurations and CH4/C2H6 feed compositions to determine the most effective way for enhanced natural gas conversion and benzene production.

cocatalyst bed configuration↗
DOE OSTI2025

High-Fidelity Modeling of Fuel-To-Coolant Thermomechanical Transport Behaviors Under Transient Conditions

This report summarizes the work completed under NEUP project number 21-24006. The objectives of this project are to advance the high-fidelity modeling capabilities and important phenomena that is important for high-burnup UO 2 and accident tolerant fuels (ATF) during transient conditions. Accurate modeling of the time-dependent phenomena that impact material performance must be used to determine the figures of merit and safety margin. Phenomena such as fuel fragmentation, cladding oxidation, pellet-clad interaction, clad ballooning, and clad rupture are examples that pose challenges to modeling during these transients. This project focused on the development of high-fidelity tightly coupled multiphysics models that can capture the time-dependent material response and associated thermal hydraulic conditions during these events. These models can then be validated against existing separate effects tests and in-pile integral experiments and will be used to model Transient Reactor Test facility (TREAT) loss-of-coolant accidents (LOCA) experiments. To achieve the project objective, we used a combination of NEAMS and NRC codes to model various LOCA test sets for the separate effects and in-pile integral experiments. BlueCRAB tool set, which can accurately predict material response at a sub-fuel pin level, as well as modeling the entire reactor system response to these events. Fuel performance was modeled using BISON (various versions) and FAST (version 1.2.1). BISON and FAST can model on a sub-fuel pin level the fuel performance under transient conditions. Both have simplified thermal hydraulic models that are capable of providing basic coolant boundary conditions. To better capture the thermomechanical interaction between the fuel, clad, and coolant, more sophisticated thermal hydraulic models are necessary.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Fuel-Cladding Eutectic Study of Legacy Fast Flux Test Facility (FFTF) MFF HT9/U-10Zr Metallic Fuel

This report presents the first systematic investigation of fuel-cladding eutectic interaction (FCEI) in irradiated HT9/U-10Zr metallic fuel from the Fast Flux Test Facility (FFTF) Materials Fuels Form (MFF) program, using differential scanning calorimetry (DSC) coupled with scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Two irradiated fuel cross-sections, MNT07H (9.5 at% burnup, x/L = 0.78) and MNT08H (7.0 at% burnup, x/L = 0.93), were subjected to three successive isothermal annealing rounds (R1–R3) at 820°C for 20 minutes each, yielding a cumulative transient duration of one hour. This study directly addresses a recognized gap in the existing FCEI database, which previously lacked irradiated HT9/U-10Zr data at burnup levels above 8 at%. Two principal findings emerge from the study. First, for both samples, FCEI remained spatially confined within the pre-existing fuel-cladding chemical interaction (FCCI) zone boundaries after R3, with no measurable eutectic penetration into unaffected cladding beyond the original FCCI layer. This self-limiting behavior is consistent with historical Fuel Behavior Test Apparatus (FBTA) results and is attributed to the near-eutectic phase composition of the FCCI zone, which rapidly absorb the available eutectic-forming constituents and then stall penetration once the FCCI zone is consumed. A comparison with unirradiated surrogate data further supports this mechanism: whereas a U–34 at.% Fe sample would be expected to show ~176 µm of iron penetration under comparable conditions, the irradiated samples exhibited only ~20 µm, a discrepancy attributed to irradiation-induced interfacial porosity and pre-existing FCCI composition gradients. Second, for MNT08H, FCEI was observed exclusively on the half of the cladding circumference where pre-existing steady-state FCCI was present, with no detectable FCEI on the opposite half. Three hypotheses are proposed to explain this asymmetry: the inhibiting role of a zirconium-rich rind at the fuel-cladding interface; the chemical sequestration of iron by redistributed zirconium within the fuel matrix; and the persistence of fuel-cladding gaps on the FCEI-free half that preclude direct contact. All three hypotheses require further experimental investigation. The results extend the empirical FCEI database into higher-burnup territory and demonstrate the viability of DSC-based testing as a substitute for the no-longer-available FBTA apparatus. Future work will include additional cross-section testing, compilation of the full FCEI dataset, model evaluation, and DSC testing of ternary fuel compositions to broaden the experimental basis for safety assessment of sodium-cooled fast reactor systems.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Battery Material Synthesis and Scalability using a 50L Taylor Vortex Reactor (Final CRADA Report)

Under this agreement, Laminar will loan Argonne a 50L Taylor Vortex Reactor (TVR) and provide mechanical troubleshooting guidance and consulting to ensure the successful setup of the pilot-scale synthesis process. The U.S. Department of Energy (DOE) will allocate funding for the labor and materials required for the study. To evaluate the physical and electrochemical properties of the materials produced by the 50L TVR, Argonne will perform comprehensive characterizations, including XRD, SEM, PSA, ICP, tap density, and coin half-cell testing. Throughout the collaboration, Argonne will provide feedback and recommendations for mechanical improvements to the reactor system. Furthermore, Argonne will credit Laminar as a collaborator in any presentations or publications resulting from data generated by the system. Laminar will retain no rights to experimental results or intellectual property generated through the experiments conducted with the 50L TVR at Argonne.

25 ENERGY STORAGE↗
DOE OSTI2026

Effect of Mo precursors in Microwave-assisted Methane Dehydroaromatization over Mo/HZSM5 catalysts

Natural gas flaring occurs in remote shale regions due to limited pipeline takeaway capacity. The conversion of the associated natural gas into aromatics in modular microwave reactors is a viable alternative to monetize the wasted gas. Microwaves offer rapid, selective heating in compact reactor systems that can enable on-demand chemical production at the well-site. Mo-HZSM-5 catalysts are widely used for aromatic production, but the location and nature of the active sites are still under debate. This study focuses on the use of 6 different Mo precursors to elucidate insights into the Mo properties that are desirable for BTX production. The catalysts were characterized by different methods (XPS, TPR, Raman, etc) to determine differences in Mo catalytic properties that may affect performance and understand these differences through performance testing under microwave at 700C for methane dehydroaromatization. Metal precursors that enable a better distribution of Mo into the pores and over the surface lead to improved benzene yield, whereas those that limited Mo to primarily the surface suffer rapid deactivation and low benzene yields. Additionally, strong Lewis acidity that arises from the sodium containing precursor drastically shifts the product selectivity towards dehydrogenation, which produces more ethylene and carbon. This catalyst had the highest deactivation constant of all catalysts tested.

gas flaring reduction↗
DOE OSTI2021

An Algebra of Machine Learners with Applications

Machine learning (ML) methods are increasingly being applied to solve complex, data-driven problems in diverse areas, by exploiting the physical laws derived from first principles such as thermal hydraulics and the abstract laws developed recently for data and computing infrastructures. These physical and abstract laws encapsulate, typically in compact algebraic forms, the critical knowledge that complements data-driven ML models. We present a unified perspective of these laws and ML methods using an abstract algebra (A;⊕,Ⓧ), wherein the performance estimation and classification tasks are characterized by the additive ⊕ operations, and the diagnosis, reconstruction, and optimization tasks are characterized by the difference Ⓧ operations. This abstraction provides ML codes and their performance characterizations that are transferable across different areas. We describe practical applications of these abstract operations using examples of throughput profile estimation tasks in data transport infrastructures, and power-level and sensor error estimation tasks in nuclear reactor systems.

Rao, Nageswara↗
DOE OSTI2024

Supporting data for Site-specific Design Case Study for Wet Waste Hydrothermal Liquefaction and Biocrude Upgrading to Hydrocarbon Fuels

Hydrothermal liquefaction (HTL) is a thermal process that converts wet biomass to renewable hydrocarbon fuel blendstocks (i.e., renewable naphtha, renewable diesel, and sustainable aviation fuel (SAF)). It can utilize a wide range of pure and blended wet feedstocks, including sewage sludge from water resource recovery facilities (WRRF), food and agriculture wastes, algae, fats, oils and greases (FOG) and blends of dry and wet wastes/feedstocks. Historically, techno-economic analysis (TEA) and annual state of technology (SOT) assessments with standard economic assumptions used by the Bioenergy Technologies Office (BETO) were conducted for the wet waste HTL pathway leveraging experimental data collected from Pacific Northwest National Laboratory’s (PNNL) continuous flow reactor systems. The objective of the SOT assessment has been to guide and track progress of BETO’s HTL research and development (R&D) toward reduced cost and greenhouse gas (GHG) emissions for the pathway. However, gaps exist between BETO’s traditional SOT updates and the needs of key external stakeholders that – if addressed – will accelerate technology adoption. This Business Case Study aims to bridge this gap by providing an updated design, TEA, and LCA based on PNNL’s FY23 R&D with added analyses and information that provide enhanced relevance for stakeholders of the HTL technology. This includes specific siting, regional wet waste resource inventory and transportation cost analyses, fuel market information, sustainable fuel policy impacts, economic metrics of net present value (NPV) and internal rate of return (IRR), greenhouse gas (GHG) emissions analysis, and statistical analysis of cost and technical uncertainties of the HTL plant design. The study focuses on the “Detroit combined statistical area (CSA)” region for siting of a wet waste HTL plant adjacent to the Great Lakes Water Authority (GLWA) facility with guidance from industry participants. Regional resource and siting analyses were conducted to identify feedstock availability, scale, and cost, as well as a beneficial site location. TEA with detailed rigorous capital cost estimation for the specific site application was conducted to evaluate the key economic metrics of most value to industrial partners. These include total capital investment, operating costs, minimum fuel selling price (MFSP) of the biocrude and fuel blendstock, and NPV and internal rate of return IRR with sustainable fuel credits. Life cycle analysis was conducted to evaluate the supply chain greenhouse gas (GHG) emissions for the wet waste HTL process as compared with petroleum derived diesel. This study is also informed by years of R&D and process de-risking learnings and was conducted with a basic engineering HTL plant design and costing that akin to a “first-of-a-kind” plant economics. This differs from our conventional “nth plant ” SOT assessments. Specifically, the HTL process model has been updated with more operationally reliable methods for feed heating and phase separations. Further, we have implemented additional spare equipment for redundancy, a more rigorous installed equipment cost estimation approach, and additional costs associated with feed formatting and delivery, building, piping and site development. An Excel-based cost sheet based on the basic engineering design is also released alongside the report that allows users to conduct customized TEA with their own feed composition and financial assumptions.

Li, Shuyun↗
DOE OSTI2026

Dielectric Resonator Design for Low Power and Low Temperature Microwave Plasma

Waveguide-based microwave plasmas generally operate at high temperatures (2000 - 6000K)[1], making it difficult to directly interface solid materials with the plasma without significant thermal damage. Dielectric microwave resonators (DMRs), long studied for wave-based manipulation of electromagnetic radiation for telecom and optics, can focus radiation to extremely small mode volumes, creating intense localized fields with low-power input.[2] This phenomenon can be used for applications ranging from efficient plasma electronics to near-ambient plasma-materials interactions. Such DMR-based plasmas have been demonstrated a handful of times in the literature, but the majority of research towards this utilize the lowest frequency resonance mode.[3], [4], [5] By carefully controlling the geometry of cylindrical resonators, a variety of electromagnetic modes can be excited. In this work, COMSOL Multiphysics simulations are used to study the electric field enhancement and absorption properties of CaTiO3 DMRs as a function of geometry and excitation frequency. Whereas previous studies have utilized the HEM111 resonance frequency to drive low power plasma excitation, we find that higher order resonance frequencies are more effective at field enhancement and result in less power loss within the dielectric material, hence less wasted heating. The effectiveness of these modes is also geometry dependent and can be computationally optimized for plasma generation. Complementing these computational efforts, we demonstrate a new closed-system reactor design built in a WR-650 waveguide and experimentally demonstrate the formation of atmospheric argon microwave plasma using < 30 W input power on DMR dimers. We observe a shifting resonance frequency as the DMRs heat in response to microwave excitation and develop a Python-based lock-in mechanism to effectively track the DMR resonance over time, leading to stable plasma operation. We use infrared thermal imaging to monitor the temperature of the DMR dimers and surrounding quartz chamber, demonstrating thermal temperatures < 60 degreesC. Finally, we utilize optical emission spectroscopy (OES) to probe the plasma properties as a function of the resonance mode.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1974

Compatibility of refractory materials for nuclear reactor poison control systems

Metal-clad poison rods have been considered for the control system of an advanced space power reactor concept studied at the NASA Lewis Research Center. Such control rods may be required to operate at temperatures of about 140O C. Selected poison materials (including boron carbide and the diborides of zirconium, hafnium, and tantalum) were subjected to 1000-hour screening tests in contact with candidate refractory metal cladding materials (including tungsten and alloys of tantalum, niobium, and molybdenum) to assess the compatibility of these materials combinations at the temperatures of interest. Zirconium and hafnium diborides were compatible with refractory metals at 1400 C, but boron carbide and tantalum diboride reacted with the refractory metals at this temperature. Zirconium diboride also showed promise as a reaction barrier between boron carbide and tungsten.

Sinclair, J. H.↗
NASA NTRS1976

Chemical vapor deposition growth

The chemical vapor deposition (CVD) method for the growth of Si sheet on inexpensive substrate materials is investigated. The objective is to develop CVD techniques for producing large areas of Si sheet on inexpensive substrate materials, with sheet properties suitable for fabricating solar cells meeting the technical goals of the Low Cost Silicon Solar Array Project. Specific areas covered include: (1) modification and test of existing CVD reactor system; (2) identification and/or development of suitable inexpensive substrate materials; (3) experimental investigation of CVD process parameters using various candidate substrate materials; (4) preparation of Si sheet samples for various special studies, including solar cell fabrication; (5) evaluation of the properties of the Si sheet material produced by the CVD process; and (6) fabrication and evaluation of experimental solar cell structures, using standard and near-standard processing techniques.

Ruth, R. P.↗
NASA NTRS1976

Chemical vapor deposition growth

A laboratory type CVD reactor system with a vertical deposition chamber and sample pedestal heated by an external RF coil has been extensively modified by installation of mass flow controllers, automatic process sequence timers, and special bellows-sealed air-operated valves for overall improved performance. Various film characterization procedures, including classical metallography, SEM analyses, X ray diffraction analyses, surface profilometry, and electrical measurements (resistivity, carrier concentration, mobility, spreading resistance profiles, and minority-carrier lifetime by the C-V-t method) area used to correlate Si sheet properties with CVD parameters and substrate properties. Evaluation procedures and measurements are given. Experimental solar cell structures were made both in epitaxial Si sheet (on sapphire substrates) and in polycrystalline material on alumina substrates, the former to provide an indication of what might be an upper limit on performance of the latter. Preliminary results are given, as obtained in cell structures not specially designed to allow for the unique properties of the sheet material, and fabricated in material known to be far from optimum for photovoltaic performance. Low power conversion efficiencies have been obtained in the epitaxial as well as the polycrystalline Si sheet.

Ruth, R. P.↗
NASA NTRS1977

Thermionic energy conversion technology - Present and future

Aerospace and terrestrial applications of thermionic direct energy conversion and advances in direct energy conversion (DEC) technology are surveyed. Electrode materials, the cesium plasma drop (the difference between the barrier index and the collector work function), DEC voltage/current characteristics, conversion efficiency, and operating temperatures are discussed. Attention is centered on nuclear reactor system thermionic DEC devices, for in-core or out-of-core operation. Thermionic fuel elements, the radiation shield, power conditions, and a waste heat rejection system are considered among the thermionic DEC system components. Terrestrial applications include topping power systems in fossil fuel and solar power generation.

Shimada, K.↗