Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Screening analysis and selection of emission reduction concepts for intermittent combustion aircraft engines

An analysis was conducted to screen, evaluate, and select three engine exhaust emission reduction concepts from a group of 14 candidate alternatives. A comprehensive literature search was conducted to survey the emission reduction technology state-of-the-art and establish contact with firms working on intermittent combustion engine development and pollution reduction problems. Concept development, advantages, disadvantages, and expected emission reduction responses are stated. A set of cost effectiveness criteria was developed, appraised for relative importance, and traded off against each concept so that its merit could be determined. A decision model was used to aid the evaluators in managing the criteria, making consistent judgements, calculating merit scores, and ranking the concepts. An Improved Fuel Injection System, Improved Cooling Combustion Chamber, and a Variable Timing Ignition System were recommended to NASA for approval and further concept development. An alternate concept, Air Injection, was also recommended.

Rezy, B. J.↗
NASA NTRS1977

Noise reduction evaluation of grids in a supersonic air stream with application to Space Shuttle

Near field acoustic measurements were obtained for a model supersonic air jet perturbed by a screen. Noise reduction potential in the vicinity of the space shuttle vehicle during ground launch when the rocket exhaust flow is perturbed by a grid was determined. Both 10 and 12 mesh screens were utilized for this experiment, and each exhibited a noise reduction only at very low frequencies in the near field forward arc. A power spectrum analysis revealed that a modest reduction of from 3 to 5 decibels exists below a Strouhal number S sub t = 0.11. Above S sub t = 0.11 screen harmonics increased the observed sound pressure level. The favorable noise reductions obtained with screens for S sub t 0.11 may be of substantial interest for the space shuttle at ground launch.

Seiner, J. M.↗
NASA NTRS1978

An investigation of the reduction of carbon dioxide in a silent electric discharge

The reduction of CO2 to O2 and CO in a silent electric discharge was studied. It was found that current alone (in the ionized plasma induced by the silent electric discharge) was reponsible for the CO2 reduction process. Voltage and frequency were important only in so far as they induced current in the plasma. Pressure and temperature were of minimum influence in the process. The large power consumption in the process was recognized as resulting from the low power factor of the reactor vessel which electrically behaved like a capacitor. The power factor was subsequently improved by adding an inductive element to make the reactor vessel capacitance part of a resonant circuit. It was found that the CO2 reduction process was most efficient in terms of power vs reduction rate when a voltage was employed that was only slightly higher than that needed to induce the plasma.

Luce, R. S.↗
NASA NTRS1977

Apollo 14 - Oxide, metal, and olivine mineral chemistries in 14072 with a bearing on the temporal relationships of subsolidus reduction

One of three primary objectives of the reported study is related to the definition of the distribution of troilite and Fe and the evaluation of the role of FeS in subsolidus reduction assemblages. Another objective was concerned with the definition of the lower limit of stabilizing elements such as Mg, Al, and Cr in ulvospinel to determine the terminal compositions at which reduction is inhibited. The third objective involves a comparison of the mineral chemistries of decomposed olivine with unaltered olivine in an attempt to determine the temperature limits. The sample was selected because it is one of the most intensely reduced samples returned from the moon. The model invoked for reduction is a magmatic-deuteric process which requires an environment approximating that of a closed system in which the volatile constituents are contained and in which reduction proceeds continuously with crystallization.

Haggerty, S. E.↗
NASA NTRS1977

The effect of carbon on phosphate reduction

Several experiments were performed in order to evaluate the effect of carbon on phosphate reduction in synthetic systems. It was attempted to simulate in the experiments conditions occurring during lunar impact processes, but without shock pressure. Temperature, oxygen fugacity, and bulk chemistry were evaluated separately in order to determine the conditions which are suitable for carbon reduction. It appears on the basis of the results of the reported investigation that carbon can be an effective reducing agent during reheating events such as those encountered by lunar soils and breccias. Phosphate reduction may be viewed as a two-step process in which carbon is mobilized as CO during heating and preferentially dissolved in the metal phase. It then acts as a reducing agent on cooling. Gas phase transport and diffusion of carbon in metal are sufficiently rapid to allow uniform carbon distribution both within and between metal grains. The availability of metal from meteorites and carbon from the solar wind is probably sufficient to make reduction by carbon a significant process on the lunar surface.

Friel, J. J.↗
NASA NTRS1978

The response of the zonally averaged circulation to stratospheric ozone reductions

The effects of various ozone density reductions of the zonally averaged circulation are evaluated with a numerical quasi-geostrophic model. If the ozone perturbations are confined to the polar regions and are minuscule on a global basis as was characteristic of the August 1972 solar proton event, then the calculations indicate a negligible effect on the mean circulation. For global ozone perturbations by predicted halocarbon pollution, about 10% reduction in the zonal jet strength and less than a 5% change in global mean stratospheric temperature are calculated. Large, uniform ozone reductions (above 50%) produce significant effects on the mean circulation: a substantial collapse of the stratosphere due to cooler temperatures, and a weak polar night jet. The reflection and transmission of quasi-stationary planetary waves in the middle atmosphere are computed to be insensitive to solar activity as extreme as the August 1972 solar proton event. It thus seems improbable that planetary waves are a viable mechanism for solar-weather interactions that involve perturbations of the zonally averaged circulation by ozone density reductions.

Schoeberl, M. R.↗
NASA NTRS1977

Quiet Clean Short-haul Experimental Engine (QCSEE) main reduction gears test program

Sets of under the wing (UTW) engine reduction gears and sets of over the wing (OTW) engine reduction gears were fabricated for rig testing and subsequent installation in engines. The UTW engine reduction gears which have a ratio of 2.465:1 and a design rating of 9712 kW at 3157 rpm fan speed were operated at up to 105% speed at 60% torque and 100% speed at 125% torque. The OTW engine reduction gears which have a ratio of 2.062:1 and a design rating of 12,615 kW at 3861 rpm fan speed were operated at up to 95% speed at 50% torque and 80% speed at 109% torque. Satisfactory operation was demonstrated at powers up to 12,172 kW, mechanical efficiency up to 99.1% UTW, and a maximum gear pitch line velocity of 112 m/s (22,300 fpm) with a corresponding star gear spherical roller bearing DN of 850,00 OTW. Oil and star gear bearing temperatures, oil churning, heat rejection, and vibratory characteristics were acceptable for engine installation.

Misel, O. W.↗
NASA NTRS1983

Turbulent drag reduction for external flows

Paper presents a review and summary of turbulent drag reduction approaches applicable to external flows. Because relatively recent and exhaustive reviews exist for laminar flow control and polymer (hydrodynamic) drag reduction, the paper focuses upon the emerging areas of nonplanar geometry and large eddy alteration. Turbulent control techniques for air generally result in modest (but technologically significant) drag reductions (order of 20 percent or less) whereas hydrodynamic approaches can yield drag reductions the order of 70 percent. Paper also includes suggestions for alternative concepts and optimization of existing approaches.

Bushnell, D. M.↗
NASA NTRS1984

Mixed Models and Reduction Techniques for Large-Rotation, Nonlinear Analysis of Shells of Revolution with Application to Tires

An effective computational strategy is presented for the large-rotation, nonlinear axisymmetric analysis of shells of revolution. The three key elements of the computational strategy are: (1) use of mixed finite-element models with discontinuous stress resultants at the element interfaces; (2) substantial reduction in the total number of degrees of freedom through the use of a multiple-parameter reduction technique; and (3) reduction in the size of the analysis model through the decomposition of asymmetric loads into symmetric and antisymmetric components coupled with the use of the multiple-parameter reduction technique. The potential of the proposed computational strategy is discussed. Numerical results are presented to demonstrate the high accuracy of the mixed models developed and to show the potential of using the proposed computational strategy for the analysis of tires.

Noor, A. K.↗
NASA NTRS1984

Optimization and application of riblets for turbulent drag reduction

Riblet surfaces have been tested in boundary layers having different upstream histories and at higher Reynolds numbers than previously reported. The drag reduction for the riblet surfaces was found to be dependent on the height and spacing of the riblets in law-of-the-wall variables regardless of the free-stream Reynolds number or upstream boundary-layer history. Micro-photographs of the actual riblet geometries are examined to determine the effect of rib details on the riblet drag-reduction performances. To further increase drag-reduction performance, riblet surfaces are combined with another drag-reduction concept, the large-eddy breakup device (LEBU). In addition, the yaw sensitivity of riblets is evaluated, as well as the characteristics of riblet surfaces manufactured out of a thin vinyl sheet.

Walsh, M. J.↗
NASA NTRS1985

Reduction method for thermal analysis of complex aerospace structures

A reduction method which combines classical Rayleigh-Ritz modal superposition techniques with contemporary finite-element methods is applied to transient nonlinear thermal analysis of aerospace structures. The essence of the method is the use of a few thermal modes from eigenvalue analyses as basis vectors to represent the temperature response in the structure. The method is used to obtain approximate temperature histories for a portion of the Shuttle orbiter wing subject to reentry heating and for a large space antenna reflector subject to heating associated with a low Earth orbit. The reduction method has excellent potential for significant size reduction for radiation-dominated problems such as the antenna reflector. However, for conduction-dominated problems such as the Shuttle wing, especially those with complex spatial and temporal variations in the applied heating, additional work appears necessary to find alternate sources of basis vectors which will permit significant problem size reductions.

Shore, C. P.↗
NASA NTRS1984

On the connection between multigrid and cyclic reduction

A technique is shown whereby it is possible to relate a particular multigrid process to cyclic reduction using purely mathematical arguments. This technique suggest methods for solving Poisson's equation in 1-, 2-, or 3-dimensions with Dirichlet or Neumann boundary conditions. In one dimension the method is exact and, in fact, reduces to cyclic reduction. This provides a valuable reference point for understanding multigrid techniques. The particular multigrid process analyzed is referred to here as Approximate Cyclic Reduction (ACR) and is one of a class known as Multigrid Reduction methods in the literature. It involves one approximation with a known error term. It is possible to relate the error term in this approximation with certain eigenvector components of the error. These are sharply reduced in amplitude by classical relaxation techniques. The approximation can thus be made a very good one.

Merriam, M. L.↗
NASA NTRS1984

NASA research on viscous drag reduction II

An assessment is made of determinations from NASA research on viscous drag reduction for aircraft, which extends to both laminar flow control and turbulent drag reduction methods. Attention is given to achievements in natural and suction-induced laminar flow control, hybrid systems incorporating both principles, turbulent drag reduction by means of low momentum fluid injection from discrete tangential slots, large eddy breakup devices, and an 'ion wind' system that functions on an inversion of the corona wind phenomenon. Surface-based drag reduction effects under study involve 'riblets', or small longitudinal surface striations, convex curvatures, and rigid, wavy walls.

Bushnell, D. M.↗
NASA NTRS1985

Turbulent drag reduction for external flows

A summary of turbulent drag reduction approaches applicable to external flows is given. Because relatively recent and exhaustive reviews exist for laminar flow control and polymer (hydrodynamic) drag reduction, the focus here is upon the emerging areas of nonplanar geometry and large-eddy alteration. Turbulent control techniques for air generally result in modest (but technologically significant) drag reductions (order of 20 percent or less), whereas hydrodynamic approaches can yield drag reductions the order of 70 percent. Suggestions are included for alternative concepts and optimization of existing approaches.

Bushnell, D. M.↗
NASA NTRS1985

Errors in reduction methods

A mathematical basis is given for comparing the relative merits of various techniques used to reduce the order of large linear and nonlinear dynamics problems during their numerical integration. In such techniques as Guyan-Irons, path derivatives, selected eigenvectors, Ritz vectors, etc., the nth order initial value problem of /y(dot) = f(y) for t greater than 0, y(0) given/ is typically reduced to the mth order (m is much less than n) problem of /z(dot) = g(z) for t greater than 0, z(0) given/ by the transformation y = Pz where P changes from technique to technique. This paper gives an explicit approximate expression for the reduction error e-i in terms of P and the Jacobian of f. It is shown that: (a) reduction techniques are more accurate when the time rate of change of the response y is relatively small; (b) the change in response between two successive stations contributes to the errors at future stations after the change in response is transformed by a filtering matrix H, defined in terms of P; (c) the error committed at a station propagates to future stations by a mixing and scaling matrix G, defined in terms of P, Jacobian and of f, and time increment h. The paper discusses the conditions under which the reduction errors may be minimized and gives guidelines for selecting the reduction basis vector, i.e., the columns of P.

Utku, S.↗
NASA NTRS1987

Reduction of the radar cross section of arbitrarily shaped cavity structures

The problem of the reduction of the radar cross section (RCS) of open-ended cavities was studied. The issues investigated were reduction through lossy coating materials on the inner cavity wall and reduction through shaping of the cavity. A method was presented to calculate the RCS of any arbitrarily shaped structure in order to study the shaping problem. The limitations of this method were also addressed. The modal attenuation was studied in a multilayered coated waveguide. It was shown that by employing two layers of coating, it was possible to achieve an increase in both the magnitude of attenuation and the frequency band of effectiveness. The numerical method used in finding the roots of the characteristic equation breaks down when the coating thickness is very lossy and large in terms of wavelength. A new method of computing the RCS of an arbitrary cavity was applied to study the effects of longitudinal bending on RCS reduction. The ray and modal descriptions for the fields in a parallel plate waveguide were compared. To extend the range of validity of the Shooting and Bouncing Ray (SBR) method, the simple ray picture must be modified to account for the beam blurring.

Chou, R.↗
NASA NTRS1987

Enhanced viscous flow drag reduction using acoustic excitation

Proper acoustic excitation of a single large-eddy break-up device can increase the resulting drag reduction and, after approximately 40 to 50 delta downstream, provide net drag reduction. Precise optimization of the input time delay, amplitude and response threshold is difficult but possible to achieve. Drag reduction is improved with optimized conditions. The possibility of optimized processing strongly suggests a mechanism which involves interaction of the acoustic waves and large eddies at the trailing edge of the large eddy break-up device. Although the mechanism for spreading of this phenomenon is unknown, it is apparent that the drag reduction effect does tend to spread spanwise as the flow convects downstream. The phenomenon is not unique to a particular blade configuration or flow velocity, although all data have been obtained at relatively low Reynolds numbers. The general repeatibility of the results for small configuration changes serves as verification of the phenomenon.

Nagel, Robert T.↗
NASA NTRS1988

The NASA/AHS Rotorcraft Noise Reduction Program

Research of the NASA/AHS noise reduction program is discussed, stressing work in four areas: noise prediction, testing and data base, noise reduction, and criteria development. A program called ROTONET has been developed, using a code structure divided into four main parts; main- and tail-rotor blade geometry, rotor performance, noise calculations, and noise propagation. Wind tunnel tests on individual rotors, and flight tests on a helicopter built specifically to generate a broadband main rotor noise data base have been conducted. In the field of noise reduction, researchers have performed analytical evaluations of low noise rotor concepts, and small-scale wind tunnel evaluations of noise reduction concepts. Under the supervision of the FAA, the program in conducting tests to develop criteria for helicopters and heliports.

Childress, Otis S., Jr.↗