Search NASA⌕ Search

SEARCH · Search NASA

Results for “STEELS - CLEANING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Mechanical Properties of Additively Manufactured 316L Stainless Steel Before and After Neutron Irradiation–FY23

This report presents the observed mechanical behavior of the additively manufactured (AM) 316L stainless steel (SS) before and after neutron irradiation. In the Advanced Materials and Manufacturing Technologies (AMMT) program, a variety of mechanical and physical property data are generated and accumulated to assess the AM austenitic alloy for nuclear reactor applications. The testing and evaluation task in the FY 2023 focused on elucidating the effects of sampling location and build size on the mechanical properties of AM 316L SS (in stress-relieved condition) before and after neutron irradiation. The laser powder bed fusion (LPBF) process produced 316L plates of three distinct sizes from which SS-J3 miniature tensile specimens were machined from six different locations. The tensile specimens were irradiated in the High Flux Isotope Reactor (HFIR) normally to 2 and 10 dpa at the target temperatures of 300 °C and 600 °C. Post-irradiation tensile testing was performed at room temperature, 300 °C, and 600 °C. The mechanical properties of AM 316L SS were significantly influenced by the characteristic microstructures of printed materials, which include fine grains and high-density dislocations. Compared with the traditional 316L SS, AM 316L showed higher initial strength and lower ductility. Regardless of sampling location, the AM 316L steel retained relatively high strength and ductility to the highest irradiation dose. A prompt necking at yield (with little uniform ductility) was observed after irradiation at 300 °C but no embrittlement was observed up to 10 dpa. Ductilization by irradiation–the radiation-induced increase of ductility–was observed for the 600 °C irradiation only and it occurred in low dose range only. The neutron irradiation increased the data variation in many tensile property datasets, particularly after 600 °C irradiation, and no clear dependence of tensile properties on build thickness or sampling location was observed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dynamic Data-Driven Multiscale Modeling for Predicting Microstructure and Mechanical Properties of 316L Stainless Steel

We have developed a long short-term memory stacked ensemble (LSTM-SE) surrogate modeling approach that can provide rapid predictions of microstructural evolution and the resultant mechanical properties of American Iron and Steel Institute (AISI) 316L series stainless steel (316LSS) fuel cladding under conditions of varying temperature and radiation dose rate. To acquire training data, we developed and implemented a kinetic Monte Carlo (KMC) model to simulate precipitation kinetics of M 23 C 6 , γ', and G phases within SS316L cladding. Experimentally reported precipitation kinetics of SS316L in literature were linked to the kinetic parameters of the simulated precipitation in our KMC model. The model was then used to simulate microstructure evolution under synthetically generated treatments of varying temperature and radiation dose rate, for periods of up to 3000 hours. Changes in volume fraction, number density, and particle size of precipitates were recorded, and particle area fractions were correlated using statistical methods to develop the surrogate model. Simultaneously, the mechanical properties of the simulated microstructures were evaluated using microstructure-based finite element method (FEM) analysis to determine the elastic modulus, yield stress, ultimate tensile strength, and elongation to failure of the aged microstructures. Using this approach, our surrogate model can predict precipitation behavior within 0.25% volume fraction and mechanical properties within 6% relative error from the values predicted by the KMC and FEM models using 50 training simulations as input. The trained recurrent neural network-based model can return estimations of precipitation kinetics and mechanical properties ~1000 times faster than the physics-based codes. This work demonstrates, as a proof of concept, that reactor material service lifetimes under variable service conditions can be predicted for a statistics-based model from a practicably obtainable dataset.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Highly Permeable Rubbery Thin Film Composite Membranes for CO2 Capture from Steel Mills

This presentation will report the rational design and fabrication of NETL’s highly permeable non-aging thin film composite (TFC) membranes for CO2 capture from various industrial point sources. This talk will also cover the design, computational fluid dynamic simulation, 3D printing, and permeation testing of plate-and-frame membrane modules for an upcoming field demonstration at U. S. Steel’s Edgar Thomson Plant in Braddock, PA. The field test will demonstrate membrane-based CO2 capture from a blast furnace for decarbonization of steel manufacturing for the first time in the U.S. A mobile gas permeation test unit is currently under design and construction for the field test, which is scheduled to take place in 2025.

Zhu, Lingxiang↗
DOE OSTI2024

Lifetime Energy Savings Via Advanced Manufacturing of Low Density Steels for Transportation Applications

The purpose of this “Low Density Steels for Transportation Applications” project was to develop an alloy composition and processing parameters that would result in a material suitable for use in automotive structural components at a reduced density over the current advanced high strength steel (AHSS) materials used. The project work successfully developed a robust alloy capable of exceeding project mechanical property targets at each stage of development, with an 8% density reduction over benchmark AHSS materials (7.8 g/cm3). The developed alloy has the potential to offer significant vehicle lightweighting and improved fuel economy, without sacrificing the increased passenger safety of more traditional AHSS. Through the three tasks of the project, (1) Alloy design and small-scale laboratory evaluation, (2) Laboratory development of hot rolled material and (3) Laboratory development of a cold rolled material, the laboratory work utilized advanced characterization and analytical methods on novel alloy compositions subjected to both conventional and non-conventional processing operations.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Tensile Properties of Austenitic Stainless Steel Tubing with Internal Hydrogen/Tritium

Can microstructure explain the observed influence of hydrogen/tritium on tensile ductility? • Hydrogen is believed to interact with dislocations, grain boundaries, vacancies, and other microstructural features2 • How hydrogen and helium (He) interact with austenitic stainless steels remains a vigorous debate • We hypothesize that: • Hydrogen isotopes and decay helium act like solutes strengthening the steel and promoting planar deformation structures that reduce tensile ductility • These changes in mechanical behavior are not the same for differing microstructures

Wieber, Natalie↗
DOE OSTI2023

Analysis of Pitting Corrosion on Wrought and Additively Manufactured 316L Stainless Steel in Atmospheric Environments

Additive manufacturing of metal components enables rapid fabrication of complex geometries. However, metal additive manufacturing also introduces new morphological and microstructural characteristics which might be detrimental to component performance. Here we report the pitting corrosion properties of wrought and additively manufactured 316L stainless steel after atmospheric exposure to coastal environments and laboratory-created environments. Qualitative visualization in combination with quantitative analysis of resulting pits provided an in-depth understanding of pitting differences between wrought and additively manufactured 316L stainless steel and between coastal and laboratory-based exposure. Optical and scanning electron microscopy were utilized for visualization, while white light interferometry measured pits across approximately 5mm x 5mm areas on each sample. Post-processing of the interferometry data enables quantification of pitting attack for each sample in terms of both pit depth and pit volume. The pitting analysis introduced herein offers a new technique to compare pitting attack between different manufacturing processes and materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Mechanical Performance of Additively Manufactured ODS 316L and 316H Stainless Steels

This work package within the Advanced Materials and Manufacturing Technologies (AMMT) program focused on the mechanical and microstructural characterization of oxide dispersion strengthened (ODS) stainless steels produced using advanced manufacturing techniques. The research aimed to identify an accelerated development path for ODS alloys by integrating additive manufacturing (AM) technologies with recent advancements in ODS materials and traditional manufacturing methods. For FY 24, the research specifically targeted exploring an accelerated development path for ODS alloys by combining AM technologies with these advancements. Novel AM and post-build processing routes were developed for ODS austenitic alloys, including Fe-Cr-Ni alloys such as 316L and 316H. Electron microscopy and mechanical characterizations were conducted to evaluate the impact of process variables on microstructure and properties, with the goal of optimizing these properties economically. Traditionally, producing ODS alloys involves multi-day, high-energy mechanical milling of alloy powder with yttria powder, followed by milled-powder consolidation through extrusion or other methods, and additional thermomechanical processing (TMP) for property control. To overcome the challenges associated with this complex and costly approach, we propose exploring alternative, cost-effective processing routes that emphasize AM and traditional TMP methods. The new processing routes for ODS alloys have achieved significantly higher strengths—several times greater than those of wrought stainless steels—while maintaining substantial ductility and fracture toughness. This report outlines the novel and economical AM-based processing routes for ODS austenitic alloys, combined with post-build TMPs, and discusses the mechanical and microstructural characteristics of the developed materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Computer vision models and advanced TEM imaging for microstructures of irradiated AM316 stainless steels

Advancements were made in automating microscopy-based material characterization, particularly in studying irradiation effects on additively manufactured (AM) materials using machine learning (ML) and computer vision (CV). These automation efforts address the challenges of analyzing complex microstructures, accelerating the detection of irradiation-induced defects. Two CV models were developed at Argonne National Laboratory (ANL) to enhance transmission electron microscopy (TEM) analysis of irradiated AM 316 stainless steel. The first model focused on the detection of irradiation-induced dislocation loops, which contribute to material hardening and embrittlement. These loops, categorized as faulted or perfect, were automatically detected and classified using a Mask R-CNN model trained on TEM images from both in-situ and ex-situ ion irradiation experiments. The model achieved high accuracy, with precision, recall, and F1 scores of 0.839, 0.734, and 0.776, respectively, demonstrating its effectiveness in analyzing dislocation loops in irradiated AM materials. The second CV model was developed to analyze the size and wall thickness of dislocation cells in laser powder bed fusion (LPBF) 316 stainless steel. Using a U-Net++ architecture with EfficientNet as the encoder, the model was trained on TEM images to segment and measure cell size and wall thickness.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Highly Permeable Rubbery Thin Film Composite Membranes for CO2 Capture from Steel Mills

For presentation at the 2024 AIChE Annual Meeting, San Diego, CA, October 27-31, 2024. High-permeance and CO2-selective membranes are needed to make membrane technology economically viable for large-scale deployment of carbon capture from various industrial point sources such as steel mills. Thin film composite (TFC) membranes are necessary for this practical implementation because they can provide high permeance by forming a thin selective layer on top of a porous support layer. This presentation reports the rational design and fabrication of National Energy Technology Laboratory’s highly permeable non-aging TFC membranes achieved by: (1) synthesizing a high-performance rubbery selective material; (2) developing a high-porosity membrane support; (3) optimizing coating methods to assemble the two materials into scalable membranes; and (4) scaling up membrane supports and TFCs via a roll-to-roll process. This talk will also cover the design, computational fluid dynamic simulation, 3D printing, construction, and permeation testing of plate-and-frame membrane modules for an upcoming field demonstration at U. S. Steel’s Edgar Thomson Plant in Braddock, PA.

Zhu, Lingxiang↗
DOE OSTI2024

Results from an Aeromagnetic Survey to Detect Steel-Cased Wells at a Marcellus Shale Well Site in Washington County, Pennsylvania

Pennsylvania has a 150-year history of oil and gas production—the longest of any state—and this enduring activity has resulted in the drilling of more than 300,000 recorded wells. However, unknown wells likely exist because innumerable wells were drilled during Pennsylvania’s intense early oil and gas history when incomplete records were kept of well locations. There is concern that early wells are likely to be ineffectively sealed because there were no laws that required plugging when the wells were abandoned. Today, many undocumented and unplugged wells are thought to be in areas of emerging shale gas and shale oil development where open wellbores can provide a pathway for undesired upward migration of fluids and gas from hydraulically fractured reservoirs. Due to this concern, Pennsylvania regulators have asked operators to locate orphaned and abandoned wells within a 1,000-ft buffer of proposed new wells. The objective of this report is to demonstrate that high-resolution aeromagnetic surveys, historic air photos, and Light Detection and Ranging (LiDAR) imagery can be rapid and effective methods to reconnoiter large, forested areas of moderate terrain for the presence of abandoned wells. These well-finding methods were evaluated at a proposed Marcellus Shale gas drilling site in Washington County, Pennsylvania, where the methods collectively located 18 confirmed wells: 15 wells were identified from aeromagnetic surveys, two wells were identified from inspection of historical air photos, and one well was identified by evaluation of state-wide LiDAR imagery. Only six wells were previously known, and their locations, as recorded in Pennsylvania’s statewide oil and gas wells database (PA/IRIS/WIS), were often too inaccurate for the wells to be found in the dense underbrush. Twelve wells identified in this study were abandoned, unmarked, and undocumented. Aeromagnetic surveys locate wells by detecting the unique magnetic signature of vertical, steel well casing, which is depicted on magnetic maps as a “bull’s eye” type anomaly that is centered directly over the well. However, when wells were drilled and found to be sub-economic, their casing was sometimes pulled and salvaged for reuse. Such wellbores provide no magnetic response and go undetected if all casing was removed. Oftentimes attempts to retrieve well casing were not 100% successful. For example, historical records for one well in the study area indicate that the well was completed in 1902 as a dry hole and that, to the extent possible, the casing was pulled for reuse. However, a section of 10-in. diameter steel casing was not recovered and remains at an unknown depth in the wellbore. This well was easily detected by the aeromagnetic survey although only deep casing remained in the well. To mitigate for the likelihood that wellbores exist where most or all casing has been removed, this study augmented aeromagnetic data with historic air photos and digital terrain models generated from LiDAR datasets—both databases are publicly available at no cost for areas within Pennsylvania. These complementary methods located three wells where the aeromagnetic anomaly, although present, was subtle and overlooked. Together, these methods determined accurate locations for six known wells within the study area and located 12 previously unknown wells. Although it is not certain that these methods successfully located all wells in the study area, the application of these methods does represent a significant improvement over relying on existing databases for well locations. For the Appendix to the report, see: https://www.netl.doe.gov/energy-analysis/details?id=b46c417a-7c9e-4d25-b810-e6248b0217f4</p>

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2023

Preliminary Characterization and Evaluation on FFF Manufactured 316H and ODS Steels

The Advanced Materials and Manufacturing Technology (AMMT) program develops cross-cutting technologies in support of a broad range of nuclear reactor technologies and maintains U.S. leadership in materials and manufacturing technologies for nuclear energy applications. The overarching vision of AMMT is to accelerate the development, qualification, demonstration, and deployment of advanced materials and manufacturing technologies to enable reliable and economical nuclear energy. Solid-state advanced manufacturing techniques can overcome some of the challenges in liquid-based additive manufacturing (AM) processes and should therefore be considered in material design and manufacturing as well. The work presented in this report forms part of a study on solid-state AM techniques of 316 stainless steels (SS) and oxide dispersion strengthened (ODS) steel components and supports the vision and goals of the AMMT program relevant to accelerate the development and deployment of advanced manufacturing processes. Achieving this can provide a safety improvement through larger safety margins, economic benefit for higher efficiency during operation, and a cost reduction through more effective manufacturing processes and less waste. This study provides preliminary information on development of the fused-filament fabrication (FFF) process using different powder types to demonstrate the sensitivity, and therefore the characterization of these sample components. The full solid-state manufacturing feasibility study will be completed and reported in a final feasibility evaluation during 2025. The study investigation used two 14YWT ODS powder batches, which provided information and the effect of different powder morphologies on manufacturability. The two 316SS powders demonstrated the effect of powder size on the manufacturability using FFF. Two product forms, namely a honeycomb structure and flat samples, were manufactured to demonstrate the flexibility of product form.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Evaluation of printability methodologies and feasibility to down select LBPF steel and other materials for nuclear applications

In this work, new research is underway to produce alloys beyond well-known alloys with modified compositions that are better suited to be produced with additive manufacturing. These alloys can only possess improved radiation tolerance but also improved high temperature strength, creep resistance while also using elements that reduce the amount of activation after irradiation. This work package supports the vision and goals of the Advanced Materials and Manufacturing Technology (AMMT) program relevant to accelerate the development and deployment of advanced manufacturing processes. This work focuses on evaluating the methodology for designing alloys best suited for AM processes based on “printability”, literature research to evaluate and down select steel alloy systems. In this work, microstructural characterization and testing activities have been performed on certain steel alloys to support the efforts from collaborating laboratories during the evaluation and printing of the test articles. The final recommendation will be performed by all four participating laboratories.

316L↗
DOE OSTI2022

Exploring the Impact of N Solubility and Trace Elements on the Creep Properties of P92 Steel

Trace elements can have major consequences on the properties of creep resistant martensitic steels. To better understand the changes in microstructure and mechanical performance associated with the variation of trace elements and enable design of steels operating at more demanding conditions, we formulated three versions of P92 within the specified allowable N, B, C and Si ranges. Different service conditions were explored, and >80% decrease in creep life was observed at 625°C 155MPa for the highest B and N containing alloy. Multiscale characterization (OM, SEM, TEM) revealed key changes due to the trace element variation. The high trace content alloy formed deleterious BN precipitates with morphology that would promote crack nucleation, but also formed higher fractions of beneficial MX precipitates. The alloy with the lowest trace content showed the best creep performance – a result of the refined precipitate populations and the absence of large-scale inclusions and BN precipitates.

Antonov, Stoichko↗
DOE OSTI2024

Decarbonization of the Iron and Steel Sector: Challenges and Opportunities

With a global initiative to reduce greenhouse gas emissions, the iron & steel industry presents an impactful decarbonization opportunity. In the U.S., the iron & steel industry accounted for 4.8% of industrial CO2 emissions in 2019, or about 72 M tonnes of CO2. This poster presents on the techno-economics of retrofitting blast oxygen furnace (BOF) iron/steel plants in the U.S. with capture.

Hughes, Sydney↗
DOE OSTI2024

Technical report Letter: RAFM, ODS steels and MMLC for Nuclear energy application

The lifetime, thermodynamic efficiency, safety and economic viability of new generation fission and fusion reactor concepts can largely be tied to the mechanical performance and stability of structural alloys under extreme environments. In this context, engineered nano materials could have broad-reaching impact on the future of advanced nuclear fuel-cycle and reactors. These systems are characterized by a large number density of interfaces which are efficient sinks for point defects and moderately biased; therefore limiting the deleterious effects of irradiation. Broadly, nuclear nano-technology deals with the use of the latest engineered-nanomaterials for improving the nuclear power performances and safety in all areas of nuclear energy production to bring new generations of nuclear power units. New advanced fuel assembly designs also have implications for securities and safeguards. To support the readiness for potential future license applications, an understanding of the technologies that would enable new reactor designs in the areas of component performance and domestic safeguards is necessary. This technical report letter work explores the technical issues and potential regulatory considerations associated with developing and adopting fuel claddings made of advanced nano- materials. Specifically three classes of nanomaterials are considered: (i) reduced activation ferritic/martensitic (RAFM) steels, (ii)oxide dispersed steels (ODS) and (iii) multi-metallic layered composites (MMLC).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

FEED Study of Carbon Capture Inc. DAC and CarbonCure Utilization Using United States Steel's Gary Works Waste Plant

The University of Illinois Urbana-Champaign (UIUC) is spearheading a front-end engineering design (FEED) study of a Direct Air Capture and Utilization System (DACUS) that can remove 5,000 tonnes/yr net CO2 from ambient air, utilizing it in the production of concrete. The designed system, if built, would be larger than any currently existing DAC collector. Such carbon negative technologies are critical to meeting the goals of the DOE’s program to accelerate climate-critical technology. DAC is a promising new technology for reducing the greenhouse gas in the atmosphere but is expensive, partly due to the energy required to capture and then release CO2 during the process. By integrating CarbonCapture Technologies Inc. DAC collector at United States Steel's Gary Works and utilizing steel plant's waste heat, energy, and location so energy & transportation costs can be minimized. CarbonCapture has developed an innovative DAC system using novel adsorbents to cost- effectively capture CO2. The captured, liquified CO2 will be trucked to ready-mix concrete plants across Illinois, Indiana, & Wisconsin, where CarbonCure will inject it into concrete during the mixing process. The carbon dioxide reacts with concrete, mineralizing into calcium carbonate (CaCO3), sequestering the CO2 into the concrete, and reducing the amount of cement, the manufacturing of which is among the major sources of CO2 emissions. This FEED study demonstrates a full CO2 value chain for DACUS from industrial facilities. It also provided an opportunity to assess the impact of this holistic approach on job creation, regional economic impact, and environmental justice.

Carbon management, ccus, carbon capture, utilizati↗
DOE OSTI2024

Field Validation of Electrocoagulation Treatment for Oily Wastewater at a Steel Mill

Oily wastewater is a significant byproduct across various industries, including steel production, posing environmental and health risks. Steelmaking is particularly water-intensive, with an estimated 75,000 gallons required to produce 1 ton of steel, although recycling reduces this to 13,000–23,000 gallons per ton.1 Water serves multiple purposes in steelmaking, including equipment cooling, scale removal, steam generation, lubrication, and pollution control.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Novel High Resolution High Temperature In-Line Sensors for Steel Manufacturing

To support efficiency, productivity, yield improvements, and future industry 4.0 and SMART manufacturing objectives for a competitive and prosperous steel industry, this program has embarked on an effort to develop, demonstrate and deploy several novel sensing technologies based on fiber optics for use in production steel facilities. Over the duration of this program, our team has successfully demonstrated three of these technologies: (1) near continuous Rayliegh Scattering optical frequency domain reflectometry (OFDR) sensing with single mode silica fibers for temperature sensing to 700 C, (2) semi-distributed fiber Bragg grating (FBG) sensing with multimode sapphire fibers for temperature sensing to >1600 C, and (3) remote in-situ Raman analysis for slag and flux chemistry analysis at steelmaking temperatures >1550 C. Each of these sensor and interrogation systems was developed, refined, and tested in our labs at Missouri S&T and then successfully deployed at SSAB’s production facilities at two sites, one in Montpelier, IA and one in Mobile, AL.

36 MATERIALS SCIENCE↗