Search NASA⌕ Search

SEARCH · Search NASA

Results for “SWITCH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Input filter design for switching regulators

A small signal average model is derived to study analytically the complex interaction among input filter, output filter and control loop, which frequently causes degradation of switch regulator performance. Analytically based design guidelines are formulated, and key design parameters are identified. It is shown that minimization of the forward transfer characteristics and the output impedance of the input filter at filter resonance are key to designing an input filter for a switching regulator with given output filter parameters and specified line and load conditions.

Lee, F. C.↗
NASA NTRS1980

High power RF coaxial switch

A coaxial switch capable of operating in a vacuum with high RF power in the 1.2 GHz range without multipactor breakdown, and without relying on pressurization with an inert gas is described. The RF carrying conductors of the switch are surrounded with a high grade solid dielectric, thus eliminating any gaps in which electrons can accelerate.

Caro, E. R.↗
NASA NTRS1979

Future large broadband switched satellite communications networks

Critical technical, market, and policy issues relevant to future large broadband switched satellite networks are summarized. Our market projections for the period 1980 to 2000 are compared. Clusters of switched satellites, in lieu of large platforms, etc., are shown to have significant advantages. Analysis of an optimum terrestrial network architecture suggests the proper densities of ground stations and that link reliabilities 99.99% may entail less than a 10% cost premium for diversity protection at 20/30 GHz. These analyses suggest that system costs increase as the 0.6 power of traffic. Cost estimates for nominal 20/30 GHz satellite and ground facilities suggest optimum system configurations might employ satellites with 285 beams, multiple TDMA bands each carrying 256 Mbps, and 16 ft ground station antennas. A nominal development program is outlined.

Staelin, D. H.↗
NASA NTRS1979

Repetitively Q-switched Nd:BeL lasers

The thermal and mechanical characteristics which will ultimately limit the performance of Nd:BeL at high average power levels were investigated. The output beam characteristics (pulse width, peak power, beam dimensions and collimation) were determined at high repetition rates for both Nd:BeL and Nd:YAG. The output of Nd:BeL was shown to exceed that of Nd:YAG by a factor of 2.7 at low Q-switched repetition rates (1 Hz). This result follows from the smaller stimulated emission cross section of x-axis Nb:BeL compared to that of NdYAG by the same factor. At high repetition rates (10 Hz) the output of Nd:Bel falls to a level of three-fifths of its low repetition rate value while under similar tests the output of Nd:YAG remains essentially constant. A comparison of the measured values of the elasto-optic coefficients, the dn/dT values and the linear expansion coefficients for BeL and YAG failed to provide an explanation for the performance of BeL; however, thermal lensing was observed in Nd:BeL. Results imply that the output of a high repetition rate Q-switched Nd:BeL laser (high thermal loading) could be dramatically increased by utilization of a resonator design to compensate for the thermal lensing effects.

Degnan, J.↗
NASA NTRS1980

K-band high power latching switch

A 19 GHz waveguide latching switch with a bandwidth of 1400 MHz and an exceptionally low insertion loss of 0.25 dB was demonstrated. The RF and driver ferrites are separate structures and can be optimized individually. This analysis for each structure is separately detailed. Basically, the RF section features a dual turnstile junction. The circulator consists of a dielectric tube which contains two ferrite rods, and a dielectric spacer separating the ferrite parts along the center of symmetry of the waveguide to form two turnstiles. This subassembly is indexed and locked in the center of symmetry of a uniform junction of three waveguides by the metallic transformers installed in the top and bottom walls of the housing. The switching junction and its actuating circuitry met all RF performance objectives and all shock and vibration requirements with no physical damage or performance degradation. It exceeds thermal requirements by operating over a 100 C temperature range (-44 C to +56 C) and has a high power handling capability allowing up to 100 W of CW input power.

Mlinar, M. J.↗
NASA NTRS1981

Cryogenic switched MOSFET characterization

Both p channel and n channel enhancement mode MOSFETs can be readily switched on and off at temperatures as low as 2.8 K so that switch sampled readout of a VLWIR Ge:Ga focal plane is electronically possible. Noise levels as low as 100 rms electrons per sample (independent of sample rate) can be achieved using existing p channel MOSFETs, at overall rates up to 30,000 samples/second per multiplexed channel (e.g., 32 detectors at a rate of almost 1,000 frames/second). Run of the mill devices, including very low power dissipation n channel FETs would still permit noise levels of the order of 500 electrons/sample.

Source record↗
NASA NTRS1981

Push-pull converter with energy saving circuit for protecting switching transistors from peak power stress

In a push-pull converter, switching transistors are protected from peak power stresses by a separate snubber circuit in parallel with each comprising a capacitor and an inductor in series, and a diode in parallel with the inductor. The diode is connected to conduct current of the same polarity as the base-emitter juction of the transistor so that energy stored in the capacitor while the transistor is switched off, to protect it against peak power stress, discharges through the inductor when the transistor is turned on, and after the capacitor is discharges through the diode. To return this energy to the power supply, or to utilize this energy in some external circuit, the inductor may be replaced by a transformer having its secondary winding connected to the power supply or to the external circuit.

Mclyman, W. T.↗
NASA NTRS1981

Repetitive Q-switched operation of x-axis Nd:La2Be2O5

The repetitive Q-switched performances of an x-axis neodymium-doped lanthanum beryllate (Nd:BeL) laser and the current state-of-the-art Nd:YAG laser are compared. Output beam pulse energy, peak power, pulse width, beam divergence and mode pattern were measured for a gold-plated single elliptical cavity using a xenon flashlamp for excitation. The output of the Nd:BeL laser is found to exceed that of the Nd:YAG laser by a factor of two at Q-switched repetition rates on the order of 1 Hz, due to the smaller stimulated emission cross section of the x-axis Nd:BeL. When the repetition rate is increased to 10 Hz, the Nd:BeL output falls to a level three fifths lower than its low-rate value, while Nd:YAG output remained essentially constant. Analysis reveals that the decrease in output may be attributed to a depolarization loss due to thermally induced stress birefringence.

Tucker, A. W.↗
NASA NTRS1981

A new approach to the minimum weight/loss design of switching power converters

A new technique using the mathematical nonlinear programming ALAG is proposed to facilitate design optimizations of switching power converters. This computer-aided approach provides a minimum weight (or loss) design down to the details of component level and concurrently satisfies all related power-circuit performance requirements. It also provides such design insights as tradeoffs between power loss and system weight as the switching frequency is increased.

Lee, F. C.↗
NASA NTRS1981

An efficient procedure for scheduling packets in a multibeam satellite-switched TDMA system

A satellite-switched, multi-beam system using N sub T transponders is considered, in which a large number of ground stations are distributed over N sub Z (not less than N sub T) zones. Each station transmits information digitally in a packet-switched time division multiple access mode, with all packets of fixed length. A demand-assigned packet scheduling procedure is described which achieves high throughput with relatively low average time delay, adapts easily to fluctuating demand from individual earth stations, and automatically schedules transmissions to avoid adjacent zone interference.

Stern, T. E.↗
NASA NTRS1983

High Power Switching Transistor

Improved switching transistors handle 400-A peak currents and up to 1,200 V. Using large diameter silicon wafers with twice effective area as D60T, form basis for D7 family of power switching transistors. Package includes npn wafer, emitter preform, and base-contact insert. Applications are: 25to 50-kilowatt high-frequency dc/dc inverters, VSCF converters, and motor controllers for electrical vehicles.

Hower, P. L.↗
NASA NTRS1984

Improved Two-Phase Switching Regulator

Coupled-inductor polyphase regulator has better efficiency and lower inductor losses. Improved two-phase switching regulator employs negative coupling between inductors to achieve better power-to-weight ratio while reducing peak switching currents and inductor losses. Improvement of about 35 percent using new technique.

Rippel, W. E.↗
NASA NTRS1983

Heat pipe thermal switch

A thermal switch for controlling the dissipation of heat between a body is described. The thermal switch is comprised of a flexible bellows defining an expansible vapor chamber for a working fluid located between an evaporation and condensation chamber. Inside the bellows is located a coiled retaining spring and four axial metal mesh wicks, two of which have their central portions located inside of the spring while the other two have their central portions located between the spring and the side wall of the bellows. The wicks are terminated and are attached to the inner surfaces of the outer end walls of evaporation and condensation chambers respectively located adjacent to the heat source and heat sink. The inner surfaces of the end walls furthermore include grooves to provide flow channels of the working fluid to and from the wick ends. The evaporation and condensation chambers are connected by turnbuckles and tension springs to provide a set point adjustment for setting the gap between an interface plate on the condensation chamber and the heat sink.

Wolf, D. A.↗
NASA NTRS1982

Packet communication system for a multi-beam beam switched satellite repeater

This paper presents the design of a packet-switched communication system using a multi-beam, beam switched satellite repeater. The protocol provides a combination of random access via Slotted ALOHA techniques and demand assigned access using collision requests. This allows efficient bandwidth usage and low average delays. Minimization of earth station cost was a major objective. This was achieved by transferring the bulk of the system complexity to the satellite repeater and the (ground) network controller. This centrally controlled protocol would allow greater system stability and would permit system reconfiguration in response to changes in traffic intensity. Sufficient signalling is also incorporated to allow both rate diversity to combat fading and timing corrections to account for satellite drift.

Bose, S. K.↗
NASA NTRS1985

Automatic Monitoring of Switching Power Supplies

Fast analysis of switching waveforms allows detection of impending failures. Switching power conditioner converts dc power from source such as battery or solar cell array to well regulated dc at convenient voltages and currents. Concept originally developed for space stations and spacecraft also suitable for power conditioning equipment in aircraft and in terrestrial photovoltaic power systems.

Moser, R. L.↗
NASA NTRS1983

Energy stores and switches for rail-launcher systems

An overview of existing switch and power supply technology applicable to space launch, a new candidate pulsed power supply for Earth-to-space rail launcher duty, the inverse railgun flux compressor, and a set of switching experiments to study further the feasibility of Earth-to-space launch are discussed.

Weldon, W. F.↗
NASA NTRS1983

Input filter compensation for switching regulators

A novel input filter compensation scheme for a buck regulator that eliminates the interaction between the input filter output impedance and the regulator control loop is presented. The scheme is implemented using a feedforward loop that senses the input filter state variables and uses this information to modulate the duty cycle signal. The feedforward design process presented is seen to be straightforward and the feedforward easy to implement. Extensive experimental data supported by analytical results show that significant performance improvement is achieved with the use of feedforward in the following performance categories: loop stability, audiosusceptibility, output impedance and transient response. The use of feedforward results in isolating the switching regulator from its power source thus eliminating all interaction between the regulator and equipment upstream. In addition the use of feedforward removes some of the input filter design constraints and makes the input filter design process simpler thus making it possible to optimize the input filter. The concept of feedforward compensation can also be extended to other types of switching regulators.

Kelkar, S. S.↗