Search NASA⌕ Search

SEARCH · Search NASA

Results for “Struts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Airframe noise: A design and operating problem

A critical assessment of the state of the art in airframe noise is presented. Full-scale data on the intensity, spectra, and directivity of this noise source are evaluated in light of the comprehensive theory developed by Ffowcs Williams and Hawkings. Vibration of panels on the aircraft is identified as a possible additional source of airframe noise. The present understanding and methods for prediction of other component sources - airfoils, struts, and cavities - are discussed. Operating problems associated with airframe noise as well as potential design methods for airframe noise reduction are identified.

Hardin, J. C.↗
NASA NTRS1977

Airplane self-noise - four years of research

A critical assessment of the state of the art in airframe self-noise is presented. Full-scale data on the intensity, spectra, and directivity of this noise source are evaluated. Vibration of panels on the aircraft is identified as a possible additional source of airframe noise. The present understanding and methods for prediction of other component sources (airfoils, struts, and cavities) are discussed, and areas for further research as well as potential methods for airframe noise reduction are identified. Various experimental methods which have been developed for airframe noise research are discussed, and sample results are presented.

Hardin, J. C.↗
NASA NTRS1976

Results of a carrier aircraft (model AX13191-4) verification test in the Boeing transonic wind tunnel using a 0.03-scale 747 CAM/orbiter model 45-0 (CA6), volume 1

Force and moment data were obtained on each vehicle both mated and separated. The investigation included the effects of orbiter incidence, orbiter tail cone, orbiter strut fairings, elevon, and body flap settings. Analysis of the data indicated the 747 is suitable as a carrier of the orbiter in both the ALT launch and ferry mode. The effect of configuration changes on drag and stability was determined.

Source record↗
NASA NTRS1977

Measurements of radon concentrations in the lunar atmosphere

The radon concentrations in the lunar atmosphere were determined by measuring the Po-210 progeny activity in artifacts returned from the moon. Experiments performed on a section of the polished aluminum strut from Surveyor 3 and data obtained from the Apollo 16 Cosmic Ray Detector Experiment Teflon thermal shield are compared with other values of the lunar radon concentration obtained at different times and different locations and by various techniques. Possible sources and release mechanisms compatible with all of the data are discussed. An experimental procedure to determine the relative retention coefficients of various types of material for radon progeny in a simulated lunar environment is described. The results of several experiments are given, and their effect on lunar radon progeny measurements is discussed. An analytical procedure is given for the analysis of a Teflon matrix for trace constituents.

Brodzinski, R. L.↗
NASA NTRS1977

Dynamic stability characteristics of the combination space shuttle orbiter and ferry vehicle

Subsonic forced-oscillation tests of a 0.015 scale model of the space shuttle orbiter/747 ferry vehicle were conducted in the Langley high speed 7- by 10-foot tunnel at Mach numbers of 0.2, 0.4, and 0.5 for angles of attack up to 12 deg. Tests were made of the basic 747 airplane, of the modified 747 (tip fins and struts added), of the ferry configuration, (747 plus orbiter at an incidence angle of 3 deg), and of the approach and landing test configuration (747 plus orbiter at an incidence angle of 6 deg).

Freeman, D. C., Jr.↗
NASA NTRS1975

Test data from solid propellant plume aerodynamics test program in Ames 6 x 6 foot supersonic wind tunnel (shuttle test FA7) (Ames test 033-66)

The aerodynamic effects of plumes from hot combustion gases in the presence of a transonic external flow field were measured to advance plumes simulation technology, extend a previously acquired data base, and provide data to compare with the effects observed using cold gas plumes. A variety of underexpanded plumes issuing from the base of a strut-mounted ogive-cylinder body were produced by combusting solid propellant gas generators. The gas generator fired in a short-duration mode (200 to 300 msec). Propellants containing 16 percent and 2 percent A1 were used, with chamber pressures from 400 to 1800 psia. Conical nozzles of 15 deg half-angle were tested with area ratios of 4 and 8. Pressures were measured in the gas generator combustion chamber, along the nozzle wall, on the base, and along the body rear exterior. Schlieren photographs were taken for all tests. Test data are presented along with a description of the test setup and procedures.

Hair, L. M.↗
NASA NTRS1977

Aeroelastic Analysis for Rotorcraft in Flight or in a Wind Tunnel

An analytical model is developed for the aeroelastic behavior of a rotorcraft in flight or in a wind tunnel. A unified development is presented for a wide class of rotors, helicopters, and operating conditions. The equations of motion for the rotor are derived using an integral Newtonian method, which gives considerable physical insight into the blade inertial and aerodynamic forces. The rotor model includes coupled flap-lag bending and blade torsion degrees of freedom, and is applicable to articulated, hingeless, gimballed, and teetering rotors with an arbitrary number of blades. The aerodynamic model is valid for both high and low inflow, and for axial and nonaxial flight. The rotor rotational speed dynamics, including engine inertia and damping, and the perturbation inflow dynamics are included. For a rotor on a wind-tunnel support, a normal mode representation of the test module, strut, and balance system is used. The aeroelastic analysis for the rotorcraft in flight is applicable to a general two-rotor aircraft, including single main-rotor and tandem helicopter configurations, and side-by-side or tilting proprotor aircraft configurations.

Johnson, W.↗
NASA NTRS1977

An experimental investigation of airframe component interference noise

Measurements of noise produced by a model of a wheel well (rectangular cavity), landing gear (wheel and strut), and flap at Mach numbers of 0.18 and 0.40 have been made in an anechoic flow facility. Individual component noise and component interference noise are described in terms of the OASPL, spectra, and streamwise or flyover directivity patterns. Areas of significant sound generation are illuminated and causes of these noise sources are suggested. Results from an acoustic imaging technique are used to point out other source regions not discernible by simple far-field measurements.

Block, P. J. W.↗
NASA NTRS1977

Validation of a Flexible Aircraft TakeOff and Landing Analysis /FATOLA/ computer program using flight landing data

A multiple-degree-of-freedom takeoff and landing analysis, Flexible Aircraft TakeOff and Landing Analysis computer program (FATOLA), was used to predict the landing behavior of a rigid-body X-24B reentry research vehicle and of a flexible-body modified-delta-wing supersonic YF-12 research aircraft. The analytical predictions were compared with flight test data for both research vehicles. Predicted time histories of vehicle motion and attitude, landing-gear strut stroke, and axial force transmitted from the landing gear to the airframe during the landing impact and rollout compared well with the actual time histories. Based on the comparisons presented, the versatility and validity of the FATOLA program for predicting landing dynamics of aircraft has been demonstrated.

Carden, H. D.↗
NASA NTRS1977

Effect of an integrated scramjet installation on the subsonic performance of an aircraft designed to Mach 6 cruise

Various factors contributing to the high drag caused by the installation of a six-module scramjet engine were determined from wind tunnel tests at Mach numbers from 0.2 to 0.7. Methods for alleviating this drag were also explored. The external exhaust nozzle, required for good cruise performance, was a major contributor. Of the drag produced by the engine modules, a significant fraction was attributable to wall divergence in the combustor. Good drag simulation could be achieved by using a single fuel injection strut having approximately the same cross-sectional area as the three used on the full-scale engine. External exhaust nozzle fences had a small but beneficial effect on maximum L/D and a flap which diverted the flow away from the inlet was effective in decreasing drag but only at low angles of attack.

Johnston, P. J.↗
NASA NTRS1977

Experimental and analytical determination of characteristics affecting light aircraft landing-gear dynamics

An experimental and analytical investigation was conducted to determine which characteristics of a light aircraft landing gear influence gear dynamic behavior significantly. The investigation focused particularly on possible modification for load control. Pseudostatic tests were conducted to determine the gear fore-and-aft spring constant, axial friction as a function of drag load, brake pressure-torque characteristics, and tire force-deflection characteristics. To study dynamic tire response, vertical drops were conducted at impact velocities of 1.2, 1.5, and 1.8 m/s onto a level surface; to determine axial-friction effects, a second series of vertical drops were made at 1.5 m/s onto surfaces inclined 5 deg and 10 deg to the horizontal. An average dynamic axial-friction coefficient of 0.15 was obtained by comparing analytical data with inclined surface drop test data. Dynamic strut bending and associated axial friction were found to be severe for the drop tests on the 10 deg surface.

Fasanella, E. L.↗
NASA NTRS1977

Results of an investigation of the acoustic and vibrational environment of a full scale space shuttle orbiter structural test panel with simulated TPS in the Ames unitary plan wind tunnel, model 81-0, test OS8A and B

Results of tests OS8A and B and pertinent test and model information are presented. The test was conducted in two parts. Test OS8A was performed in the NASA/ARC unitary 11-foot section and OS8B was conducted in the NASA/ARC unitary 9 x 7 tunnel. Test objectives were to investigate thermal protection system (TPS) tile sensitivity to extreme pressure gradients and vibration and to define the TPS aerodynamic environment. The model utilized for OS8 was a full-scale representation of a portion of the space shuttle orbiter lower wing carry-through structure forward of the aft tank strut and propellant lines. Thermal protection tiles were simulated on the model. The model was instrumented with static pressure orifices, accelerometers, and dynamic pressure transducers (Kulites). A total rake was utilized to obtain boundary layer surveys.

Kingsland, R. B.↗
NASA NTRS1978

Rectangular capture area to circular combustor scramjet engine

A new concept for a scramjet engine design was presented. The inlet transformed a rectangular shaped capture stream into a cross section which was almost circular in shape at the inlet throat or combustor entrance. The inlet inner surface was designed by the method of streamline tracing. The high pressure and temperature regions of the combustor were almost circular in shape and thus the benefits of hoop stresses in relation to structural weight could be utilized to reduce combustor and engine weights. The engine had a center body consisting of a 20 deg included angle cone, followed by a constant diameter cylinder. Fuel injection struts were arranged in a radial array and were swept 54 deg from the center body to the inlet inner surface and had values of length to maximum average thickness between 5.6and 6.6 which were felt to be structurally reasonable. Combustor wetted areas were shown to be less than those of the present fully rectangular engine concept.

Pinckney, S. Z.↗
NASA NTRS1978

Combustion of hydrogen in a two-dimensional duct with step fuel injectors

An investigation of the combustion of hydrogen perpendicularly injected from step fuel injectors into a Mach 2.72, 2100 K vitiated test gas was conducted. The model simulated the flow between the center and side struts of an integrated scramjet module at Mach 7 flight and an altitude of 29 km. Parametric variation included equivalence ratio, fuel dynamic pressure ratio, and area distribution of the model. The overall area ratio of the model was held constant at 2.87. The data analysis indicated that no measurable improvement in mixing or combustion efficiency was obtained by varying the fuel dynamic pressure ratio from 0.79 to 2.45. Computations indicated approximately 80 percent of the fuel was mixed so that it could react; however, only approximately 50 percent of the mixed fuel actually reacted in two test configurations, and 74 percent in later tests where less area expansion of the flow occurred.

Eggers, J. M.↗
NASA NTRS1978

Space Spider - A concept for fabrication of large structures

The Space Spider concept for the automated fabrication of large space structures involves a specialized machine which roll-forms thin gauge material such as aluminum and develops continuous spiral structures with radial struts to sizes of 600-1,000 feet in diameter by 15 feet deep. This concept allows the machine and raw material to be integrated using the Orbiter capabilities, then boosting the rigid system to geosynchronous equatorial orbit (GEO) without high sensitivity to acceleration forces. As a teleoperator controlled device having repetitive operations, the fabrication process can be monitored and verified from a ground-based station without astronaut involvement in GEO. The resultant structure will be useful as an intermediate size platform or as a structural element to be used with other elements such as the space-fabricated beams or composite nested tubes.

Britton, W. R.↗
NASA NTRS1978

Thermal control requirements for large space structures

Performance capabilities and weight requirements of large space structure systems will be significantly influenced by thermal response characteristics. Analyses have been performed to determine temperature levels and gradients for structural configurations and elemental concepts proposed for advanced system applications ranging from relatively small, low-power communication antennas to extremely large, high-power Satellite Power Systems (SPS). Results are presented for selected platform configurations, candidate strut elements, and potential mission environments. The analyses also incorporate material and surface optical property variation. The results illustrate many of the thermal problems which may be encountered in the development of three systems.

Manoff, M.↗
NASA NTRS1978

Aerodynamic and acoustic effects of eliminating core swirl from a full scale 1.6 stage pressure ratio fan (QF-5A)

Fan QF-5A was a modification of fan QF-5 which had an additional core stator and adjusted support struts to turn the core exit flow from a 30 deg swirl to the axial direction. This modification was necessary to eliminate the impingement of the swirling core flow on the axial support pylon of the NASA-Lewis Quiet Fan Facility that caused aerodynamic, acoustic and structural problems with the original fan stage at fan speeds greater than 85 percent of design. The redesigned fan QF-5A did obtain the design bypass ratio with an increased core airflow suggesting that the flow problem was resolved. Acoustically, the redesigned stage showed a low frequency broadband noise reduction compared to the results for fan QF-5 at similar operating conditions.

Woodward, R. P.↗
NASA NTRS1978

Free wing assembly for an aircraft

A free wing is attached to a fuselage of an aircraft in a manner such that the wing is free to pivot about a spanwise axis forward of its aerodynamic center. The wing is angularly displaced about the axis by aerodynamic pitching moments, resulting from lift, and is trimmed through a use of a trimmable free stabilizer comprising a floating canard mounted on a strut rigidly connected to the wing and projected forward from it.

Wolowicz, C. H.↗