Search NASA⌕ Search

SEARCH · Search NASA

Results for “Test methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Discovery and Analysis of Rare High-Impact Failure Modes using Adversarial RL-Informed Sampling

Adaptive learning agents have tremendous potential to handle critical tasks currently performed by humans. Unfortunately, due to their complexity, it can be difficult to verify that these learning agents do not have critical failure modes. Standard verification and validation methods often do not apply directly to learning agents and Monte Carlo methods have difficulty covering even a small fraction of the state space, especially in multiagent systems or over long time horizons. To overcome this difficulty, we demonstrate an adaptive stress-testing method based on reinforcement learning of correlations that raise the probability of failure. This approach has three key properties: (1) it is able to find rare failure modes with far greater sample efficiency than Monte Carlo methods, (2) it can estimate the true probability of a failure mode despite the inherent bias in the learning method, and (3) it is capable of learning and resampling compact representations of multimodal failure spaces. These properties are important in practice as we need to find disparate failure modes while accounting for their actual relevance. This is a significant advantage over traditional adaptive stress testing methods that give abstract likelihoods of particular failure instances, but cannot estimate the probability of a broader failure mode. We test our algorithm on a simple problem from the aviation domain where an autonomous aircraft lands in gusty wind conditions. The results suggest that we can find failure modes with far fewer samples than the Monte Carlo approach and simultaneously estimate the probability of failure.

Validation↗

An investigation of the Iosipescu and Asymmetrical Four-Point Bend tests for composite materials

The results of an extensive analytical and experimental investigation of the Iosipescu and Asymmetrical Four-Point Bend (AFPB) test methods are summarized. Finite element analyses were used to assess the influence of notch parameters and load locations on the stress state in the specimens. The shear moduli and shear strengths were experimentally measured for quasi-isotropic graphite-epoxy laminates using both the Iosipescu and the AFPB test methods with various combinations of notch parameters and load locations. The test results indicate that changes in the notch geometry and load locations aimed at improving the stress distribution in the test section result in unexpected changes in the failure mode.

Spigel, B. S.↗

Iosipescu shear properties of graphite fabric/epoxy composite laminates

The Iosipescu shear test method is used to measure the in-plane and interlaminar shear properties of four T300 graphite fabric/934 epoxy composite materials. Different weave geometries tested include an Oxford weave, a 5-harness satin weave, an 8-harness satin weave, and a plain weave with auxiliary warp yarns. Both orthogonal and quasi-isotropic layup laminates were tested. In-plane and interlaminar shear properties are obtained for laminates of all four fabric types. Overall, little difference in shear properties attributable to the fabric weave pattern is observed. The auxiliary warp material is significantly weaker and less stiff in interlaminar shear parallel to its fill direction. A conventional strain gage extensometer is modified to measure shear strains for use with the Iosipescu shear test. While preliminary results are encouraging, several design iterations failed to produce a reliable shear transducer prototype. Strain gages are still the most reliable shear strain transducers for use with this test method.

Walrath, D. E.↗

Nonlinear Unsteady Aerodynamic Modeling Using Wind Tunnel and Computational Data

Extensions to conventional aircraft aerodynamic models are required to adequately predict responses when nonlinear unsteady flight regimes are encountered, especially at high incidence angles and under maneuvering conditions. For a number of reasons, such as loss of control, both military and civilian aircraft may extend beyond normal and benign aerodynamic flight conditions. In addition, military applications may require controlled flight beyond the normal envelope, and civilian flight may require adequate recovery or prevention methods from these adverse conditions. These requirements have led to the development of more general aerodynamic modeling methods and provided impetus for researchers to improve both techniques and the degree of collaboration between analytical and experimental research efforts. In addition to more general mathematical model structures, dynamic test methods have been designed to provide sufficient information to allow model identification. This paper summarizes research to develop a modeling methodology appropriate for modeling aircraft aerodynamics that include nonlinear unsteady behaviors using both experimental and computational test methods. This work was done at Langley Research Center, primarily under the NASA Aviation Safety Program, to address aircraft loss of control, prevention, and recovery aerodynamics.

Murphy, Patrick C.↗

Investigation of nonlinear mechanical behavior of two superfine-grained graphites with DIC assisted disc splitting test

Using standardized uniaxial tensile test specimens is not practical due to the limited volumes in irradiation capsules, molten salt degradation facilities, or oxidation apparatus. The ASTM International Standard Test Method for Tensile Strength Estimate by Disc Compression of Manufactured Graphite (ASTM D8289) was developed to provide a convenient way for estimating tensile strength. Unlike the traditional uniaxial tensile test in ASTM C749 (International Standard Test Method for Tensile Stress–Strain of Carbon and Graphite), which uses dog-bone shaped specimens larger than 12.95 mm × 120.65 mm, the ASTM D8289 standard uses smaller discs with diameters of 6–12.7 mm. A digital image correlation (DIC) system, which uses a full-field noncontact surface displacement measurement technique, was applied along with the ASTM D8289 disc splitting test on IG-110 samples and compared with previous measurements from Mersen 2114 samples. Results confirmed that the DIC technique can measure the surface displacement/strain on these small (Ø6 mm × 3 mm) graphite specimens with good repeatability. However, Mersen 2114 and IG-110 samples exhibited strain discrepancies when DIC measurements were compared with analytical and finite element simulation values. The loading history and strain results also indicated different mechanical behaviors between Mersen 2114 and IG-110, particularly the nonlinear behavior of the IG-110 samples. Good agreement was observed by comparing the splitting tensile strengths of two superfine-grained grades with results from other work. The specimen size effect is discussed when comparing the splitting tensile strength with corresponding uniaxial tensile strength of these two graphite grades.

Lin, Lianshan [ORNL] (ORCID:0000000203399219)↗

Bond Testing for Effects of Silicone Contamination

In 2003 ATK Thiokol discovered that the smocks and coveralls worn by its operations personnel for safety and contamination control were themselves contaminated with a silicone defoamer and a silicone oil. As a growing list of items have been identified as having this form of contamination, it was desirable to devise a test method to determine if the contamination level detected could cause subsequent processing concerns. The smocks and coveralls could potentially contact bonding surfaces during processing so the test method focused on dry transfer of the silicone from the clothing to the bonding surface.

Plaia, James↗

Electrostatic Evaluation: SCAPE Suit Materials

The surface resistivity tests are performed per the requirements of the ESD Association Standard Test Method ESD STM11.11*. These measurements are taken using a PRS-801 resistance system with an Electro Tech System (ETS) PRF-911 concentric ring resistance probe. The tests require a five pound weight on top of cylindrical electrodes and were conducted at both ambient and low humidity conditions. In order for materials to "pass" resistivity tests the surface of the materials must either be conductive or statically dissipative otherwise the materials "fail" ESD. Volume resistivity tests are also conducted to measure conductivity through the material as opposed to conductivity along the surface. These tests are conducted using the same PRS-801 resistance system with the Electro Tech System PRF-911 concentric ring resistance probe but are performed in accordance with ESD Association Standard Test Method ESD STM11.l2**.

Buhler, Charles↗

Full-field Strain Methods for Investigating Failure Mechanisms in Triaxial Braided Composites

Composite materials made with triaxial braid architecture and large tow size carbon fibers are beginning to be used in many applications, including composite aircraft and engine structures. Recent advancements in braiding technology have led to commercially viable manufacturing approaches for making large structures with complex shape. Although the large unit cell size of these materials is an advantage for manufacturing efficiency, the fiber architecture presents some challenges for materials characterization, design, and analysis. In some cases, the static load capability of structures made using these materials has been higher than expected based on material strength properties measured using standard coupon tests. A potential problem with using standard tests methods for these materials is that the unit cell size can be an unacceptably large fraction of the specimen dimensions. More detailed investigation of deformation and failure processes in large unit cell size triaxial braid composites is needed to evaluate the applicability of standard test methods for these materials and to develop alternative testing approaches. In recent years, commercial equipment has become available that enables digital image correlation to be used on a more routine basis for investigation of full field 3D deformation in materials and structures. In this paper, some new techniques that have been developed to investigate local deformation and failure using digital image correlation techniques are presented. The methods were used to measure both local and global strains during standard straight-sided coupon tensile tests on composite materials made with 12 and 24 k yarns and a 0/+60/-60 triaxial braid architecture. Local deformation and failure within fiber bundles was observed, and this local failure had a significant effect on global stiffness and strength. The matrix material had a large effect on local damage initiation for the two matrix materials used in this investigation. Premature failure in regions of the unit cell near the edge of the straight-sided specimens was observed for transverse tensile tests in which the braid axial fibers were perpendicular to the specimen axis and the bias fibers terminated on the cut edges in the specimen gage section. This edge effect is one factor that could contribute to a measured strength that is lower than the actual material strength in a structure without edge effects.

Littell, Justin D.↗

Some possible reference materials for fire toxicity tests

Suitable reference materials need to be selected in order to standardize any test method. The evaluation of cotton, polyethylene, polyether sulfone, polycarbonate, polystyrene, and polyurethane flexible and rigid foams as possible reference materials for the University of San Francisco/NASA toxicity screening test method is discussed.

Hilado, C. J.↗

Drawbar Pull (DP) Procedures for Off-Road Vehicle Testing

As NASA strives to explore the surface of the Moon and Mars, there is a continued need for improved tire and vehicle development. When tires or vehicles are being designed for off-road conditions where significant thrust generation is required, such as climbing out of craters on the Moon, it is important to use a standard test method for evaluating their tractive performance. The drawbar pull (DP) test is a way of measuring the net thrust generated by tires or a vehicle with respect to performance metrics such as travel reduction, sinkage, or power efficiency. DP testing may be done using a single tire on a traction rig, or with a set of tires on a vehicle; this report focuses on vehicle DP tests. Though vehicle DP tests have been used for decades, there are no standard procedures that apply to exploration vehicles. This report summarizes previous methods employed, shows the sensitivity of certain test parameters, and provides a body of knowledge for developing standard testing procedures. The focus of this work is on lunar applications, but these test methods can be applied to terrestrial and planetary conditions as well. Section 1.0 of this report discusses the utility of DP testing for off-road vehicle evaluation and the metrics used. Section 2.0 focuses on test-terrain preparation, using the example case of lunar terrain. There is a review of lunar terrain analogs implemented in the past and a discussion on the lunar terrain conditions created at the NASA Glenn Research Center, including methods of evaluating the terrain strength variation and consistency from test to test. Section 3.0 provides details of the vehicle test procedures. These consist of a review of past methods, a comprehensive study on the sensitivity of test parameters, and a summary of the procedures used for DP testing at Glenn.

wheel↗

Fire-related standards and testing

The state of the art of flammability testing has been changing rapidly. Here, the progress in developing general test methods for solid materials and products exposed to an external fire are reviewed. The special requirements pertinent to environments of concern to NASA are examined and some suggestions for possible directions for future test method developments are given.

Babrauskas, Vytenis↗

Proposed Ground Testing Standard Methods and Techniques

The methodologies used for prediction for on-orbit microgravity environment needs to be ground validated. The data and models for such validation will be coming from diverse sources. No standardized methodologies have been validated which cover the entire 0 - 300 Hz range. Current ground test data feeds into this process and therefore should be standardized to support both narrow and third octave band analysis.

Goodnight, Thomas↗

Recent NASA Wind Tunnel Free-Flight Testing of a Multirotor Unmanned Aircraft System Vehicle

Wind tunnel free-flight tests of a small quadrotor vehicle were completed in the NASA Langley 12-Foot Low Speed Tunnel and 20-Foot Vertical Spin Tunnel. The primary objective of these tests was to acquire flight data in forward and descending flight for the purpose of assessing the fidelity of an all-attitude flight dynamics simulation previously developed from static and dynamic wind tunnel data. A secondary objective was to demonstrate and mature free-flight test methods specific to the emerging class of small unmanned aircraft and urban air mobility vehicles. Experimental flight data correlated well with simulation predictions which included steady trim conditions consistent with straight and level flight and quasi-steady conditions associated with descent velocities prone to vortex ring state development. The test method was shown to be well suited to these classes of vehicles and several unique infrastructure requirements, including tether systems and data acquisition requirements were identified. In addition, unique operational test techniques and safety procedures were developed to accommodate the testing. Results of these tests will be used to support air traffic management studies and research into safety assurance concepts that enable the integration of these classes of vehicles into the National Airspace System.

John V Foster↗

Optimized testing of meshes

Efficient testing techniques for two-dimensional mesh interconnection networks are presented. The tests cover faults in the arbitration logic of the switches; this includes an examination of fault detection in the data paths, routing, and control circuitry, including the conflict resolution capabilities of mesh interconnection networks using topological test methods. The proposed methods are not implementation specific and can be applied to any design with a mesh topology. The topology and behavior of the network are described and definitions are presented. The fault model is defined and parallel testing methods for the entire network are given.

Malek, Miroslaw↗

Fracture mechanics life analytical methods verification testing

Verification and validation of the basic information capabilities in NASCRAC has been completed. The basic information includes computation of K versus a, J versus a, and crack opening area versus a. These quantities represent building blocks which NASCRAC uses in its other computations such as fatigue crack life and tearing instability. Several methods were used to verify and validate the basic information capabilities. The simple configurations such as the compact tension specimen and a crack in a finite plate were verified and validated versus handbook solutions for simple loads. For general loads using weight functions, offline integration using standard FORTRAN routines was performed. For more complicated configurations such as corner cracks and semielliptical cracks, NASCRAC solutions were verified and validated versus published results and finite element analyses. A few minor problems were identified in the basic information capabilities of the simple configurations. In the more complicated configurations, significant differences between NASCRAC and reference solutions were observed because NASCRAC calculates its solutions as averaged values across the entire crack front whereas the reference solutions were computed for a single point.

Favenesi, J. A.↗

Speckle Pattern for Woven Softgood Habitats Photogrammetry Testing

Space habitation is becoming more accessible and commercially available which is driving the development and testing of inflatable softgoods habitats that can be both lighter and more volume-efficient than heritage metallic pressure vessels. Photogrammetry test methods are used on new materials and larger inflatable softgood test articles to measure material displacement and strain during pressurization. A speckle pattern must be applied to the surface of interest for testing when using photogrammetry which is typically a very labor and time intensive process. Two methods were tested as options for a faster and more effective application to hand painting and temporary tattoos, which are the current application methods for the structural/restraint layer. One approach was to mix a plastic additive with a matte clear coat to create a speckle pattern that could be applied to the article. The second method uses a speckle paint gun to speckle the article after a white base coat is applied. Both methods adhered well to the Kevlar test sample materials and showed up well when examined with photogrammetry cameras. On the woven test samples the additive in a clear coat method could be applied evenly as was the paint gun method.

Rylee Cardon↗

Speckle Pattern Application to Woven Softgoods

Space habitation is becoming more accessible and commercially available which is driving the development and testing of inflatable softgoods habitats that can be both lighter and more volume-efficient than heritage metallic pressure vessels. Photogrammetry test methods are used on new materials and larger inflatable softgood test articles to measure material displacement and strain during pressurization. A speckle pattern must be applied to the surface of interest for testing when using photogrammetry which is typically a very labor and time intensive process. Two methods were tested as options for a faster and more effective application to hand painting and temporary tattoos, which are the current application methods for the structural/restraint layer. One approach was to mix a plastic additive with a matte clear coat to create a speckle pattern that could be applied to the article. The second method uses a speckle paint gun to speckle the article after a white base coat is applied. Both methods adhered well to the Kevlar test sample materials and showed up well when examined with photogrammetry cameras. On the woven test samples the additive in a clear coat method could be applied evenly as was the paint gun method.

Rylee Cardon↗

Speckle Pattern Application to Woven Softgoods

Space habitation is becoming more accessible and commercially available which is driving the development and testing of inflatable softgoods habitats that can be both lighter and more volume-efficient than heritage metallic pressure vessels. Photogrammetry test methods are used on new materials and larger inflatable softgood test articles to measure material displacement and strain during pressurization. A speckle pattern must be applied to the surface of interest for testing when using photogrammetry which is typically a very labor and time intensive process. Two methods were tested as options for a faster and more effective application to hand painting and temporary tattoos, which are the current application methods for the structural/restraint layer. One approach was to mix a plastic additive with a matte clear coat to create a speckle pattern that could be applied to the article. The second method uses a speckle paint gun to speckle the article after a white base coat is applied. Both methods adhered well to the Kevlar test sample materials and showed up well when examined with photogrammetry cameras. On the woven test samples the additive in a clear coat method could be applied evenly as was the paint gun method.

Rylee Cardon↗